® POLLY Installation Manual Toilet Partitions and Dressing Compartments Metpar Corp 95 State Street, Westbury, New York, USA, 11590 Tel: 516-333-2600 ~ Fax: 516-333-2618 ~ www.Metpar.com ~ E-mail: Service@Metpar.
• • • • • • • • • • • • • • • • • • Table of Contents Stop! Before you begin Suggested tools Metpar tips Hardware nomenclature Step 1 - Layout Step 2 - Prepare Stiles Step 3 - Position Panel Step 4 - Attach Stiles Step 5 - Secure stiles to panel Step 6 - Headrail & Panel fasten Step 7 - Install Door & Hinge Step 8 – Install Door Latch Step 9 – Care & Maintenance Step 10 - Need Help? Page 1 Page 1 Page 2 Page 2 Page 3 Page 3 Page 3 Page 4 Page 5 Page 5 Page 6 Page 7 Page 7 Page 7 Before you begin, note
üMetpar tips… 1. Plan ahead… coordinate all of the materials and hardware for each specific layout. Study your layout drawings and evaluate any special conditions that may require custom size materials, unique hardware or special tools. 2. When you determine the centerline dimensions, refer to the stall depths shown on your layout drawings. The centerline is ½” less than the stall depth. 3. Read all of these instructions carefully and thoroughly.
STEP 1 - Layout A. Mark the centerline of each stile location from the back wall. The centerline of the stile is ½" less than the overall dimension shown. Measure out at each end of overall distance from first stall to last line. B. Mark the centerline of all 54” full height wall brackets. C. From the sidewall measure along the centerline of the stiles to locate the floor fasteners, to be located 1" in from each end of each pilaster. D. Mark all bracket holes to be drilled using brackets as templates. E.
STEP 4A - Attach Stile FP500 A. Place plastic anchors into the floor holes. B. Over each floor anchor place these items in the following order; one (1) shoe clip and one (1) bracket. Fasten into anchor with #12 x 1½” screw. C. Loosely install ¼-20 nuts and bolts thru each bracket on bottom of stiles. Note the use of washers on either side of each L-bracket. See detail 4C. D.
STEP 4C - Attach Stile FT700 A. Place expansion shields into floor holes. B. Screw (hand tight) 3/8” studs into shields. C. On each stud place these items in the following order; one (1) shoe clip and one (1) washer. D. Screw one (1) 3/8” nut onto each stud. Tighten nuts to expand anchor. Place one (1) nut and one (1) round washer onto each stud. E. Lower the stile over the studs and place on each stud these items in the following order; one (1) clamp, one (1) round washer, screw on one (1) nut. F.
STEP 7A – Door Installation with Integral Hinge A. Review this detail and read the instructions before you begin. Be certain that you have all the correct parts. B. Turn the door over so the bottom is “face up”. The bottom has a metal heat sink. Insert the female half of the 2-piece cam into the bottom hole of the door. With a 1/8” drill bit, drill a 1/8” hole through the edge of the door into the nylon cam. Screw the setscrew to lock the cam in place.
STEP 8A – Concealed Round Round Latch Installation A. Put slide bar through small hole in side of door with notch facing up. B. Choose which indicator ring will be used; Green on tab for OUTSWING doors, Red on tab for INSWING doors. Install the indicator ring by lining up the tabs with the notches in the door hole. C. Place the "OUTSIDE HALF" of the latch (with the slot) into the hole, and through the slide bolt. D.
