User's Manual

545C Operations Manual
02/10/2012
56
© 2012 Meteorcomm LLC.
5.2.7 Script Files
The MCC-
545C must be programmed with the parameters that “fit” the
network that it is being used in, whether as a Base Station, Repeater, or
Remote Station.
This programming is
from the operator terminal into the MCC
A Script File can also be downloaded into a Remote Station via RF from the
Master Station.
The appropriate Script File is usually programmed int
factory prior to shipment
been entered, a new file can be loaded from your operator terminal using
XTermW software
.
545C to operat
e as a Remote Station in your specific network.
Other Script Files define application programs that are performed by the
station.
For example, the application for a Remote Station may be as a
mobile unit reporting position data or as a fixed site reporting
New Script Files may be entered into MCC
outlined in Section 3.3.3.5 and Appendix C
already loaded in the unit’s Parameter Memory (also called CPM), may be
made using the Station Con
5.2.8
CPU Power Mode
The CPU of the MCC
mode.
Use the _LPSTP command to select the CPU power mode
low-
power mode, the CPU uses a “hibernate” mode to conserve batter
power.
The _LPSTP command is displayed as a Factory Default Parameter.
To select low-
power mode, enter:
_LPSTP,ON
To select low-
power mode, enter:
_LPSTP,OFF
Important:
Using the CPU in high
545C Remote Station t
System Administrator to make certain whether the network configuration
Prerelease
DCN
© 2012 Meteorcomm LLC.
All Rights Reserved. Proprietary and Confidential. Do Not Distribute.
545C must be programmed with the parameters that “fit” the
network that it is being used in, whether as a Base Station, Repeater, or
This programming is
accomplished by loading a Script File
from the operator terminal into the MCC
-
545C via the Operator (MNT) port
A Script File can also be downloaded into a Remote Station via RF from the
The appropriate Script File is usually programmed int
o the MCC
factory prior to shipment
.
If the appropriate Script File has already not
been entered, a new file can be loaded from your operator terminal using
.
There is one Script File that uniquely programs the MCC
e as a Remote Station in your specific network.
Other Script Files define application programs that are performed by the
For example, the application for a Remote Station may be as a
mobile unit reporting position data or as a fixed site reporting
New Script Files may be entered into MCC
-
545C using the procedures
outlined in Section 3.3.3.5 and Appendix C
.
Changes to a Script File that is
already loaded in the unit’s Parameter Memory (also called CPM), may be
made using the Station Con
figuration commands listed previously.
CPU Power Mode
The CPU of the MCC
-545C also runs in either high-
power or low
Use the _LPSTP command to select the CPU power mode
power mode, the CPU uses a “hibernate” mode to conserve batter
The _LPSTP command is displayed as a Factory Default Parameter.
power mode, enter:
power mode, enter:
Using the CPU in high
-
power mode causes that particular MCC
545C Remote Station t
o use higher power consumption. Check with your
System Administrator to make certain whether the network configuration
DCN
00001789-A
All Rights Reserved. Proprietary and Confidential. Do Not Distribute.
545C must be programmed with the parameters that “fit” the
network that it is being used in, whether as a Base Station, Repeater, or
accomplished by loading a Script File
545C via the Operator (MNT) port
.
A Script File can also be downloaded into a Remote Station via RF from the
o the MCC
-545C at the
If the appropriate Script File has already not
been entered, a new file can be loaded from your operator terminal using
There is one Script File that uniquely programs the MCC
-
e as a Remote Station in your specific network.
Other Script Files define application programs that are performed by the
For example, the application for a Remote Station may be as a
mobile unit reporting position data or as a fixed site reporting
sensor data.
545C using the procedures
Changes to a Script File that is
already loaded in the unit’s Parameter Memory (also called CPM), may be
figuration commands listed previously.
power or low
-power
Use the _LPSTP command to select the CPU power mode
. While in
power mode, the CPU uses a “hibernate” mode to conserve batter
y
The _LPSTP command is displayed as a Factory Default Parameter.
power mode causes that particular MCC
-
o use higher power consumption. Check with your
System Administrator to make certain whether the network configuration