User's Manual

02/10/2012
© 2012 Meteorcomm LLC. All Rights Reserved.
is used by the MCC
checksum is invalid, the unit will revert to factory defaults.
The only configuration parameter that is not stored in CPM is the CR10X
pointer.
This parameter, together with the date and time, is stored in
clock chip battery backed up RAM
is discharged or removed from the unit
FACTORY,DEFAULT,INIT command is used to change the configuration back
to the factory defaults.
When the MCC-
545C ships from the factory it is programmed with the
following default configuration: the Operator Port (port 0) is set for 9600
baud, 8 data bits, 1 stop bit, no parity, ASCII protocol and no flow control
This provides a known starting point for commun
terminal or computer
unit ID and other operational parameters and then use the SAVE command
to write them to CPM
effect.
Caution:
Once the software is rebooted or is restarted due to a crash or
failure of the battery backup RAM, all changes will be lost unless they were
previously saved in CPM.
5.2
Station Configuration
The station configuration parameters are usually entered b
configuration script file as described in Section 3.3.3.5
enter these commands one at a time from the operator port
describes some of the key commands
chapter for a comple
In order for the MCC
properly configured
to application, therefore refer to your systems manual or consult your
systems manage
r for correct settings.
545C Operations Manual
Prerelease
DCN
© 2012 Meteorcomm LLC. All Rights Reserved.
Proprietary and Confidential. Do Not Distribute.
is used by the MCC
-545C to verify the data in CPM is correct
.
checksum is invalid, the unit will revert to factory defaults.
The only configuration parameter that is not stored in CPM is the CR10X
This parameter, together with the date and time, is stored in
clock chip battery backed up RAM
.
These will be lost if the internal battery
is discharged or removed from the unit
.
It will not be lost if the
FACTORY,DEFAULT,INIT command is used to change the configuration back
to the factory defaults.
545C ships from the factory it is programmed with the
following default configuration: the Operator Port (port 0) is set for 9600
baud, 8 data bits, 1 stop bit, no parity, ASCII protocol and no flow control
This provides a known starting point for commun
icating to the unit from a
terminal or computer
.
From this starting point, the user can program the
unit ID and other operational parameters and then use the SAVE command
to write them to CPM
.
As soon as the parameters are entered they take
Once the software is rebooted or is restarted due to a crash or
failure of the battery backup RAM, all changes will be lost unless they were
previously saved in CPM.
Station Configuration
The station configuration parameters are usually entered b
y loading a
configuration script file as described in Section 3.3.3.5
.
It is also possible to
enter these commands one at a time from the operator port
.
describes some of the key commands
.
Refer to the last section of this
chapter for a comple
te list of commands.
In order for the MCC
-
545C to operate correctly in your network, it must be
properly configured
.
Configuration requirements will vary from application
to application, therefore refer to your systems manual or consult your
r for correct settings.
545C Operations Manual
DCN
00001789-A
49
.
If the
The only configuration parameter that is not stored in CPM is the CR10X
This parameter, together with the date and time, is stored in
the
These will be lost if the internal battery
It will not be lost if the
FACTORY,DEFAULT,INIT command is used to change the configuration back
545C ships from the factory it is programmed with the
following default configuration: the Operator Port (port 0) is set for 9600
baud, 8 data bits, 1 stop bit, no parity, ASCII protocol and no flow control
.
icating to the unit from a
From this starting point, the user can program the
unit ID and other operational parameters and then use the SAVE command
As soon as the parameters are entered they take
Once the software is rebooted or is restarted due to a crash or
failure of the battery backup RAM, all changes will be lost unless they were
y loading a
It is also possible to
.
This section
Refer to the last section of this
545C to operate correctly in your network, it must be
Configuration requirements will vary from application
to application, therefore refer to your systems manual or consult your