Installation Guide

Instruction Manual/Instrucciones/Directives
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [e-mail]
1
FCC DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following
2 conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that any unauthorized changes or modications to
this equipment not expressly approved by the manufacturer could void the user’s
authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
For T-Grid Mounting
1. Turn off the power at the main fuse/breaker box.
2. Carefully open carton and remove panel from packaging.
3. Locate fixture junction box cover and remove it (Fig. 1).
4. Remove appropriate knockout(s) for power supply wiring.
Figure 1.
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENU DU PAQUET
ITEMS REQUIRED
(Purchase separately)
• Phillips Screw Driver • Flat head Screwdriver
• Wire Cutters • Safety Glasses & Gloves
• Hammer • Ladder
• Wire Strippers
WARNINGS AND CAUTIONS
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation
and maintenance of this product must be performed by a qualified
electrician. This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation
of the product and hazards involved. The light source contained in this
luminaire shall only be replaced by the manufacturer or his service agent or
a similar qualified person.
Risk of Fire and Electric Shock- Make certain power is OFF before starting
installation or attempting any maintenance. Disconnect power at fuse or
circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow fixture to cool before handling or
servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily
injury and property damage.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or
losses of any kind that may arise from the improper, careless, or negligent installation, handling or
use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
NOTICE: Ground screw provided in proper location. Do not relocate.
NOTICE: Fixture may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable
damage on delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for
concealed damage must be filed within 15 days of delivery. All damaged material, complete with
original packing must be retained.
A. Fixture housing
Boîtier du luminaire
Carcasa de la lámpara
ENGLISH
B. Wire Nuts - (3) 14 AWG & (2) 8 AWG
Écrous de l - (3) 14 AWG et (2) 8 AWG
Tuercas de alambre - (3) 14 AWG y (2) 8 AWG
Wire Nuts
NOTE: Fixture weights are below. Ensure grid location is rated for xture weight before moving
to next step. If unsure use cable to support xture to structure above xture using the holes in
the alignment clips. (Fig 1).
CGFP or GPT models