Product Overview

R50101 1217
10. LIMITED WARRANTY
RectorSeal, LLC makes the Limited Express Warranty that when the instructions for storage and handling of our products are followed we warrant our products to be free from defects. THIS LIMITED
EXPRESS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR-
TICULAR PURPOSE, AND OF ANY OTHER OBLIGATION ON THE PART OF RECTORSEAL, LLC. The sole remedy for breach of the Limited Express Warranty shall be the refund of the purchase
price. All other liability is negated and disclaimed, and RectorSeal, LLC shall not be liable for incidental or consequential damages.
Suggestions and recommendations covering the use of our products are based on our past experience and laboratory findings. However, as we have no control as to the methods and conditions
of application, we only assume responsibility for the uniformity of our products within manufacturing tolerances.
METACAULK
®
JOINT STRIP
4. Application and
Installation
Install Metacaulk
®
Joint Strip
along with any normal backer
rod, cover it with approved
architectural caulk or sealant, and
you have a fire rated control joint.
No longer do you need to use
firestop caulks that are difficult
to install and impossible to paint
over. No need for mineral wool
or expensive, difficult to install
backing materials. Metacaulk
®
Joint Strip has the capability for 1,
2, 3 and 4 hour assembly ratings,
refer to the UL systems for specific
installation instructions.
4. Trowel sealant to the
desired finish. See tested
UL systems for complete
installation instructions.
5. Storage & Handling
Metacaulk
®
Joint Strip should be
stored between 35˚F (2˚C) and
120˚F (49˚ C). Keep products
stored under protective cover, in
their original containers. A stock
rotation program is recommended.
Shelf life of the product is indefinite.
6. Availability
Metacaulk
®
Joint Strip is available in
1" (25 mm), 1.5" (38 mm), 2" (50.8
mm), 2.5" (64 mm), 3" (76 mm) and
4" (102 mm) widths. The 4" widths
has an adhesive backing. They
come on a roll 82' ( 25 m) long.
7. Limitations
To be used only in the tested
configurations or as recommended
by RectorSeal.
8. Cautions
FOR CHEMICAL EMERGENCY, SPILL, LEAK,
FIRE, EXPOSURE OR ACCIDENT, CALL
CHEMTREC-DAY OR NIGHT 1-800-424-9300.
PRECAUTIONS: Do not take internally. May
be harmful if swallowed. May cause eye and
skin irritation if prolonged or repeated contact
occurs. Wash after handling. FIRST AID: For
any overexposure, get immediate medical
attention after first aid is given. Eyes- Flush
15 minutes with clean water. Skin-Wash with
soap and water. Ingestion-Only if conscious,
give large amounts of water and INDUCE
VOMITING. FIRE AND SPILLS: Use water
fog, CO
2
, foam, or dry chemicals. Wipe up
spills to prevent footing hazard. Clean up
with scrapers and water. STORAGE AND
HANDLING: Store away from heat sources.
KEEP OUT OF REACH OF CHILDREN.
For additional information, refer to Safety Data Sheet.
For additional technical service,
call: 713-263-8001 or 1-800-231-3345
fax: [phone] or 1-800-441-0051
RECTORSEAL
2601 SPENWICK DRIVE HOUSTON, TEXAS 77055
WWW.RECTORSEAL.COM
1. Clean all surfaces in joint area to
remove loose debris, dirt, oil, wax,
grease, old caulking, etc.
2. For floor applications, install a
separate base section of backer rod
recessed approximately 2" down from
the top of the floor. Bend and friction
fit Metacaulk
®
Joint Strip longitudi-
nally into joint using the backer rod as
the transport mechanism. Push into
joint far enough to accommodate the
required depth of caulk.
3. Gun, trowel, or pump approved
sealants to minimum 1/4”
depth on both sides of wall or
top of floor over the backer rod.