Product Overview

ManualsBrandsMetacaulk ManualsFirestop Products6" x 7" Firestop Putty Pad

D-17

10. LIMITED WARRANTY

RectorSeal, LLC makes the Limited Express Warranty that when the instructions for storage and handling of our products are followed we warrant our products to be free from defects. THIS LIMITED

EXPRESS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PAR-

TICULAR PURPOSE, AND OF ANY OTHER OBLIGATION ON THE PART OF RECTORSEAL, LLC. The sole remedy for breach of the Limited Express Warranty shall be the refund of the purchase

price. All other liability is negated and disclaimed, and RectorSeal, LLC shall not be liable for incidental or consequential damages.

Suggestions and recommendations covering the use of our products are based on our past experience and laboratory ﬁndings. However, as we have no control as to the methods and conditions

of application, we only assume responsibility for the uniformity of our products within manufacturing tolerances.

Metacaulk

Fire Rated Putty and Putty Pads

directory for selection of prop-

er system design detailing

depths of putty and backing

material.

PUTTY PADS:

Remove liner from one side

of pad (Step 1). Align with the

side of the box partially over-

lapping the stud and adhere.

Work pad to the opposite side

of the box and over the edges

(Step 2). If wall membrane is

in place, pack putty into gaps

between box and gypsum

board slightly overlapping

inner wallboard surface. If

membrane is to be installed

after pad installation, overlap

front edge of box so that putty

will be compressed around

edges of box as wallboard is

installed. Cut slits in pad to

fit around conduit or cables

(Step 3). Press pad to surface

of top, bottom, and sides of

box (Step 4). Trim excess at

corners and apply to conduit

ﬁttings connected to the box.

Remove exposed liner. Op-

tionally, putty may be packed

into inside of conduit ﬁttings

to prevent passage of smoke.

Only one putty pad thickness

(1/8") is needed for a 1 or 2

hour rating.

5. Testing Data

Metacaulk

Fire Rated Putty

is classiﬁed by Underwriters

Laboratories, Inc. as a ﬁll, void

or cavity material. Metacaulk

Fire Rated Putty Pads are

classified as a wall opening

protective material. For spe-

ciﬁc test criteria see UL Fire

Resistance Directory or call

RECTORSEAL.

Metacaulk

Fire Rated Put-

ty was tested at a minium

0.01 inch of water, positive

pressure in accordance with

UL 1479, ASTM E 814 and

CAN4-S115-M.

6. Storage & Handling

Metacaulk

Fire Rated Putty

is not to be stored in areas

where the temperatures ex-

ceed 120˚F or drop below

0˚F. Best if protected from

freezing. If freezing occurs,

thaw completely before using.

Keep products dry and stored

under protective cover in their

original containers. Products

have a minimum shelf life of 2

years subject to re-inspection

thereafter. A stock rotation

program is recommended.

7. Availability

Moldable Fire Rated Putty

available in 1 1/2 inches di-

ameter by 10 inches long (18

cubic inches)

Moldable putty pads are 6

and 7 inches by 7 inches by

1/8 inch thick.

8. Limitations

Do not expose to water.

9. CAUTIONS

FOR CHEMICAL EMER-

GENCY, SPILL, LEAK, FIRE,

EXPOSURE OR ACCIDENT,

CALL CHEMTREC - DAY OR

NIGHT 1-800- 424-9300.

For additional information, refer

to Safety Data Sheet

For additional technical

service,

call: 1-800-231-3345

Fax: 1-800-452-2824

RECTORSEAL

2601 Spenwick Drive Houston, Texas 77055