Users Manual Part 2

23 / 30
ENGLISH
INSTALLATION AND OPERATING INSTRUCTIONS DR AFT FOR OEM USE ONLY
© 2019 Mertik Maxitrol GmbH & Co. KG, All Rights Reserved.
MYFIRE WI-FI BOX (B6R-W2…)
TECHNICAL DATA
AMBIENT TEMPERATURE RANGE
32 °F to 176 °F / 0 °C to 80 °C
RADIO FREQUENCY
2.4 GHz (see radio frequency information on page 4.)
RADIATED POWER OUTPUT
19.8 dBm
POWER SUPPLY
6 VDC powered by the receiver
WIRELESS COMMUNICATION
▪ WPA2 authentication
▪ AES 256-bit encryption security
▪ Compatible with IEEE 802.11 b/g/n
POWER CONSUMPTION
Nominal: max. 0.5 W
Standby: max. 0.03 W
LED RGB CONTROL OUTPUT
Phoenix, 3 pol, MC 1.5 / 3-ST-3.5, 5 VDC - 24 VDC / 5 A
LED RGB EXTERNAL POWER INPUT
Phoenix, 2 pol, MC 1.5 / 2-ST-3.5, 5 VDC - 24 VDC / 5 A
APPROVALS / SDOC
Europe (CE); U.S. (FCC), Canada (ISED), New Zealand
(RNZ), Australia (ACMA)
MODES OF OPERATION
The myre Wi-Fi Box communicates with a home network (Wi-Fi
Router) over a wireless signal.
1. The myre Wi-Fi Box must be wired to the receiver according
to the myre App setup diagram (see gure 32, page 30)
2. Connect receiver to mains power. The myre Wi-Fi Box start
with the Access Point Mode (green/blue LED blinking). Go to
“myre App setup”…
MINIMUM REQUIREMENT FOR WI-FI ROUTER
▪ IEEE 802.11n/g/b compatibility
▪ WPA2 encryption
▪ Radio frequency: 2.4 GHz band
▪ Wireless auto channel: Automated search for WLAN radio
channel free of interference
▪ User Datagram Protocol (UDP) support
▪ Multicast DNS (mDNS) for Kwik Connect process
MINIMUM REQUIREMENT SMART DEVICE:
▪ iOS 10.0 or Android 5.0
Reset button
(Use paper clip to push button)
Receiver
LED 1
RGB
Power Input
Receiver cable
RGB 1
RGB 2
Figure 24: myre Wi-Fi Box (B6R-W2…)
LED INDICATION ON MYFIRE WI-FI BOX (see gure 24, page 23)
2 RGB LEDs
Label LED Status
Receiver
LED 1
Green Connected to receiver.
Red No data transfer between receiver and Wi-Fi Box.
Off Standby mode is active or no Power supply.
WLAN
LED 2
Green Wi-Fi connection is safe.
Blue/Green blinking Access point mode (AP mode) is active.
Red Connection to home network (Wi-Fi Router) failed.
Off Standby mode is active or no power supply.
RESET STATUS ON MYFIRE WI-FI BOX:
Press Reset
Button
LED Function
Power-On-
Reset or
1-sec-Reset
WLAN LED 2
ashes red,
green and
blue
If no network is set, the AP Mode will be activated
for 2 hours. When the network isn't set after 2
hours, the Wi-Fi Box will go to Standby Mode.
Once a network is set, the Wi-Fi Box will connect
directly.
7 secs RECEIVER
LED 1 ashes
every 500 ms
in blue
Removes the Wi-Fi settings and turns on the
Access point mode (AP mode) for 2 hours.
20 secs RECEIVER
LED 1 ashes
every 50 ms
in blue
Erases all Setup Data including Wi-Fi settings. The
AP-Mode will be activated for 2 hours.
NOTICE
▪ A Symax handset or The Puck must be used to achieve full
functionality.
▪ If mains power is lost, disconnect the myre Wi-Fi Box from
the receiver. This will prevent receiver batteries from being
drained quickly.
▪ If no network is congured, the myre Wi-Fi Box will leave the
Access Point Mode (AP Mode) after 2 hours.
▪ If you have multiple replaces using myre Wi-Fi Boxes, the
minimum distance between the myre Wi-Fi Boxes must be 60
cm (2'). A shorter distance may interfere with the data transfer.
WLAN
LED 2