User Instructions Part 1

ManualsBrandsMertik Maxitrol ManualsElectronicsHandset of remote electronic ignition and control system for gas applications

INSTALLATION INSTRUCTIONS FOR OEM USE ONLY

4 / 28

Misc. cables: 221 °F

Cable with relay: 158 °F

CE: Combination control: 0 °C to 80 °C

Latching solenoid valve: 0 °C to 80 °C

Receiver RF without batteries: 80 °C

Receiver RF with batteries: 60 °C

Handset: 60 °C

Wall switch/touch pad: 80 °C

Switch panel: 105 °C

Module: 80 °C

Ignition cable: 150 °C

HANDSETS

NOTICE

The handsets and receivers are not interchangeable with previ-

ous electronics (see ﬁ gure 7).

RADIO FREQUENCY

868 MHz for Europe

915 MHz for U.S. and for Canada.

This device complies with Part 15 of the FCC Rules and with

Industry Canada license-exempt RSS standard(s). Opera-

tion is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) This device must

accept any interference received, including interference that

may cause undesired operation. Changes or modiﬁ cations not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential instal-

lation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interfer-

ence will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one

or more of the following measures: Reorient or relocate the

receiving antenna.

BATTERIES – HANDSET

2 x 1.5 V “AAA” (quality alkaline recommended).

BATTERIES – RECEIVER

4 x 1.5 V “AA” (quality alkaline recommended).

An AC Mains Adapter may be used instead of batteries.

NOTICE

Only the Mertik Maxitrol AC Mains Adapter or one preapproved

by Mertik Maxitrol can be used. Use of other adaptors can

render the system inoperable.

V MODULE

CE: Inlet: 230 VAC/50 Hz; 210 VA

Outlet: 230 VAC/50 Hz; 100 VA each

Built-in fuse 2,5 A

CSA: Inlet: 115 VAC/60 Hz; 210 VA

Outlet: 115 VAC/60 Hz; 100 VA each

Built-in fuse 2.5 A

TECHNICAL SPECIFICATIONS

Gas combination control according to CSA or CE approval

(see label for certiﬁ cation)

APPROVALS

CSA: Multifunctional gas control according to ANSI Z21.78

6.20 and ANSI Z21.20 6.20 for U.S. & Canada

CE: Gas Appliances Directive 90/396/EEC and EN 298-2003,

DIN EN 126

FUELS

CSA: Suitable for natural, manufactured, mixed gases, lique-

ﬁ ed petroleum gases, and LP gas-air mixtures.

CE: Suitable for use with gases of EN 437 gas family 1, 2

and 3.

PRESSURE DROP/CAPACITY

CSA: 1” w.c. at 65,000 BTU/hr

CE: 2,5 mbar at 1,2 m³/h air

RANGE OF REGULATION

CSA: 10,000 to 85,000 BTU/hr

CE: Class C according EN 88

REGULATOR ADJUSTMENT

CSA: 3” w.c. to 5” w.c.; 8” w.c. to 12” w.c.

CE: 5 to 40 mbar (50 to 400 kPa)

CE + CSA: 3” w.c. to 12” w.c. (7.5 to 30 mbar)

Convertible Regulator: 3 to 4.5” NG/8.5 to 11.5” LP

MOUNTING POSITION

In upright position, gas control knobs are on top of the valve.

Valve may be mounted 0° to 90° any direction (including verti-

cal) from the upright position. Valve must NOT be mounted

upside down.

MAXIMUM INLET PRESSURE

CSA: ½ psi (14” w.c.)

CE: 50 mbar (5 kPa)

MAIN GAS CONNECTION

CSA: ⅜ NPT (ANSI/ASME B1.20.1), ⅜ Loxit

CE: Rp ⅜ (ISO 7-1/EN 10226-1), compression ﬁ ttings for

8 mm, 10 mm or 12 mm tube

PILOT GAS CONNECTION

CSA: 7/16-24 UNS for ¼” or

” tubing

CE: M10x1 for 4 mm or 6 mm tubing

INLET AND OUTLET CONNECTION

Side or Bottom

MAXIMUM ALLOWED TORQUE INLET AND OUTLET

CSA: 280 inch-pounds

CE: 35 Nm

THERMOCOUPLE/INTERRUPTER BLOCK

11/32-32 UNF, M10x1, M9x1, M8x1

AMBIENT TEMPERATURE RANGE

CSA: Combination control: 32 °F to 176 °F

Latching solenoid valve: 32 °F to 176 °F

Receiver RF without batteries: 176 °F

Receiver RF with batteries: 140 °F

Handset: 140 °F

Wall switch/touch pad: 176 °F

Switch panel: 221 °F

Module: 176 °F

Ignition cable: 302 °F

Figure 7: Previous Handsets