Warning RISK OF ELECTRIC SHOCK OR FIRE. « Make sure the power is OFF at the circuit breaker for the wall switch you are replacing. » The wall switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes, or are uncomfortable performing the installation, please call a qualified electrician. « Do not install the wall switch with wet hands or when standing on wet or damp surfaces.
2, Hardware installation. Note: You can also refer to the instructions in Merinos app and follow it step by step. a) Make sure your traditional switch is single pole switch. This smart switch is not for 3 way or 4 way switches. b) Place your smartphone near the traditional switch to make sure the location is covered by strong WI-Fi signal. ¢} Get you tools ready and turn off the power at the circuit breaker that controls the switch.
e) Unscrew the wires and connect them according to picture below. f) Push the smart switch back into the box and turn the power on at the circuit breaker. If the switch works manually and the LED is flashing amber and green, then you are good to go for setting up. If not, please turn off the power at the circuit breaker and check the wiring. For more detailed information, please refer to the Merinos app.
3. Set up the device. (1) For Android user. Open Merinos app and tap +on the top right. Just follow the instructions in Merinos app and you will set it up in minutes. If you want to use Home Kit with an i0S device after setup on Android. Just launch your Home app and scan or input the code printed on the device or user manual. No reset or extra configuration needed. TonENaikghiead ¢ Fell the lass ton losses S 2) For i0S user. Please follow instructions below. a.
¢. Use Apple Home app instead of Merinos app to set it up. Just launch your Home app and tap “Add Accessory” or + on the top right and follow the instructions. It may take a few minutes and then you'll be all set. The setup code is printed on the device and the user manual.Input the code on the label and wait. You should be able to upsetting minute.
Daedalus e Bl Akl Trainman Vil R B Dol rsi Note: 1. According to Apple Home Kit, the only way to set up Home Kit accessory with i0S is Home app. If you don’t want to set up with Home app, you will have to use an Android device. 2.If you can’t setup the device with Home app. It might be that the i0S is having cache issue with Home kit device. Please try to a. Reset the smart device and kill the Home app and retry. b. Restart your i0S$ and retry. (This is important.) ¢.
LED and Button Rules — Brightness Button Press to increase the lighting brightness. Press to decrease the lighting brightness. Status LED Flashing amber (or red) and green:Configuration | mode. Solid green: Switch on. Solid red or amber: No internet. Flashing red: WI-Fi disconnection/Resetting /Firmware upgrading/ Initiating. Off: Switch off. Brightness LED Indicate the current lighting brightness. Power Button Short press to turn the light on or off. Long press for 5s to reset the switch.
FAQ At Merinos, we strive to assure your satisfaction. We are always happy to help at 1. What should | do when | can’t turn the wall switch offing manually? Please check the Status LED. If it is off: « Make sure that you restore power to the wall switch at the circuit breaker. « Make sure the wall switch is wired correctly. Please consult with a qualified electrician. 2.
4. Why my i0S will require me to use Home app when sifting it up? This is required by Apple iOS. If you want manage your device in Merinos app, please launch your Merinos app after the setup and tap + on the top right. Merinos app will find devices in the same WI-Fi network. 5.1 can’t pair my device with Home Kit anyhow. Please make sure your i0S is connecting to the 2.4GHz of your home WI-Fi and you are having i0S 13 or above. Restart your iOS will help due to some system cache issue.
2. By using any third-party services such as Amazon Alexei, Google Assistant, Apple Home Kit. Consumer acknowledge that all data and privacy collected by such third parties are not covered by Merinos, nor Merinos would take any legal responsibility. Merinos only take responsibility for what’s covered by Merinos Privacy Policy. Consumer acknowledge understanding this clearly by reading this document.
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
SIMPLE DEVICE SIMPLIFY YOUR LIFE Email: Website: www.meross.com Made in China Designed in California. Made in China Supervisor: MR TECH USA Limited Address: 8825 53 Ave, Hurst, NY 11373, USA Manufacturer: Chengdu Merinos Technology Co., Lid. o US Address: Room 1312, Floor 13, Building 6-1, Zone E, Fustian Software Park, Boxing District, Chengdu, Sichuan, China .
