DSP520/640 DSP Loudspeaker User Guide
EN DSP520/640 User Guide Important safety instructions • • • • • • • • • • • • • Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
EN DSP520/640 User Guide Installation These instructions assume that a Meridian wall box type RF500/600 has already been mounted in the wall ready to accept the loudspeaker. If necessary, refer to the RF500/600 Wall Box Installation Instructions as appropriate. M5 button-head screws Contents Each DSP520/640 loudspeaker is supplied with the following components: • Mounting frame. • M5 x 25 screws (DSP520 8 pieces, DSP640 12 pieces). • M5 x 10 screws (DSP520 14 pieces, DSP640 20 pieces). • Scrim. • Grille.
DSP520/640 User Guide EN To fit the mounting frame Clamping screws (M5 x 25) Mounting frame Locking screws (M5 x 10) • Slide the mounting frame into the wall box. Once the frame is tight against the wall: • Clamp the frame to the wall with the M5 x 25 button-head screws (DSP520 8 pieces, DSP640 12 pieces). • Lock into place with M5 x 10 button-head screws (DSP520 6 pieces, DSP640 8 pieces). Tighten just enough to clamp the frame to the wall. Do not overtighten as this may distort the frame.
DSP520/640 User Guide EN To fit the loudspeaker To fit the scrim and grille Scrim Clamping screws (M5 x 10) Grille Magnet positions Grab handle • Using the grab handle, sit the loudspeaker on the lower edge of the wall box. • Plug in the RJ45 cable(s) and AC supply. • With the aid of the grab handle, slide the loudspeaker into position, inserting the top of the loudspeaker into the wall box first. • Fix with M5 x 10 button-head screws (DSP520 8 pieces, DSP640 12 pieces).
DSP520/640 User Guide EN Front and back panel Connections Front panel The following diagram gives details of the connections on the back of the loudspeaker: The following diagram gives details of the front of the loudspeaker: Power Channel selector SpeakerLink input output Right Fuse Fuse On CAUTION: Disconnect supply before changing fuse. Replace with same type fuse. ATTENTION: Débrancher avant de remplacer le fusible. Utiliser un fusible de rechange du même type. Off ~50-60Hz T5.
DSP520/640 User Guide EN Applications To connect a pair of DSP520/640 loudspeakers to a Meridian Audio Core 200 • Connect the upper SpeakerLink output on the AC200 to the Slave DSP520/640, using an RJ45 cable. The DSP520/640 loudspeakers are ideal for a compact Audio Core 200 based home entertainment system. • Make sure the Channel selector is set to the Left position on the front of the left loudspeaker and to the Right position on the front of the right loudspeaker.
DSP520/640 User Guide EN To use DSP520/640 loudspeakers in a Meridian Digital Theatre • Connect the appropriate SpeakerLink outputs on the G68 to each of the remaining loudspeakers, using RJ45 cables. DSP520/640 loudspeakers are ideal as the front, rear, and centre loudspeakers in a Meridian Digital Theatre, in conjunction with a Meridian Digital Surround Controller such as the G68. The following diagram shows how to connect the loudspeakers using “home run” wiring.
DSP520/640 User Guide EN To create a Sooloos system to the rest of your network, or to your Cable/DSL Modem. The DSP520/640 loudspeakers can be used in conjunction with an 818 Reference Audio Core to make a superb Sooloos system. • Connect the upper SpeakerLink output from the 818 Reference Audio Core to the Master DSP520/640 SpeakerLink input, using an RJ45 cable.
DSP520/640 User Guide EN
EN DSP520/640 User Guide 11
DSP520/640 User Guide EN
