eng © 2013 Mercury Marine i SC 1000 Tachometer/Speedometer 90-8M0081594 813
ii eng
Product Overview Basic Operation and Features..................................................... 1 Automatic Engine Detection Feature........................................... 2 Master Reset............................................................................... 3 Alarm Warnings With Descriptive Text........................................ 4 Warning Display Screens............................................................ 6 Display Screens.........................................................
iv eng
PRODUCT OVERVIEW Basic Operation and Features NOTE: Descriptive text alarm warning screens are displayed with 2007 and newer engines. 46346 System Tachometer System Speedometer Power up: Each gauge will power up when the ignition is turned on. The gauges will stay on as long as the ignition is on. Lights: Adjusts the brightness and contrast of the gauge. Buttons: The "MODE/SELECT" button is used for selecting information screens.
PRODUCT OVERVIEW PRODUCTS WITH EMISSIONS CONTROL After the ignition is turned on, the tachometer will display the name of the gauge and the version of the software for approximately two seconds. In the upper left‑hand corner of the display, a small engine icon will also be visible. The icon is a representation the power package has emissions control onboard diagnostics, also known as OBD. The icon will only be seen during the key up process unless a system fault is detected.
PRODUCT OVERVIEW Master Reset Returns the gauge to the factory defaults through the Master Reset command. IMPORTANT: Performing a Master Reset will reset the unit to the factory defaults, thus eliminating any installation and calibrations performed during set up of product. Press the "‑" and "+" buttons simultaneously for approximately 10 seconds (until the graphic bars collide) to restore the unit to factory default settings. Press the "MODE/SELECT" button to confirm.
PRODUCT OVERVIEW Alarm Warnings With Descriptive Text NOTE: Descriptive text alarm warning screens are displayed with 2007 and newer engines. a b c REDUCE THROTTLE 3200 AL RPM 46348 a - Display screen b - Engine Guardian System c - Alarm signal When a problem is detected, the name of the offending alarm appears on the display. If the problem can cause immediate engine damage, the Engine Guardian System will respond to the problem by limiting engine power.
PRODUCT OVERVIEW Alarm Warning with Descriptive Text SYS FAULT [ SHOW ] 24184 STBD SYSTEM FAULT [ EXIT ] [ NEXT ] [ MORE ] 24186 STBD SYSTEM FAULT [ EXIT ] [ NEXT ] [ ACTION ] 24187 The "SYS FAULT" bar indicates there is a problem in the system. "SHOW" displays the faulty component. The top bar indicates the system with the faulty component. The scrolling text displays the faulty component. "NEXT" displays the next fault.
PRODUCT OVERVIEW If the "MODE/SELECT" button is pressed to display a different screen, the engine emission fault alarm icon will appear in the upper left‑hand corner. The engine icon will be visible on all screens. A servicing dealer must diagnose the emission control faults and correct the problem prior to the next use of the vessel.
PRODUCT OVERVIEW PROBLEM eng TACHOMETER DISPLAY BATTERY × ENGINE DATA BUS × FAULT ‑ HORN × FAULT ‑ IGNITION × FAULT ‑ INJECTOR × FAULT ‑ OIL PUMP × FAULT ‑ SENSOR × FAULT ‑ WATER TEMP × SPEEDOMETER DISPLAY LOW FUEL × LOW OIL × FAULT ‑ OIL TEMP × OIL PSI × OVERHEAT × OVERSPEED × FAULT ‑ OIL PRESSURE × RESERVE OIL × SYSTEM FAULT – OBD SERVICE SOON × WATER IN FUEL × FAULT ‑ MAP × FAULT ‑ MAT × FAULT ‑ TPS × 7
PRODUCT OVERVIEW NOTE: Depending on the engine model and vessel options, not all screens will apply. 1 2 3 4 FAULT OVERHEAT HORN RESERVE PRESSURE 90% REMAINING OVERSPEED FAULT 7500 RPM OIL PUMP WATER FAULT IN FUEL INJECTOR 5 6 7 8 46351 IMPORTANT: Refer to the engine Operation, Maintenance, and Warranty Manual for further explanation of the problem and the correct action to take. Contact the dealer if the problem persists. 1. OVERHEAT: The engine has overheated. 2.
PRODUCT OVERVIEW NOTE: Depending on the engine model and vessel options, not all screens will apply. 9 10 FAULT FAULT IGNITION WATER TEMP FAULT BATTERY 8V NO STARBOARD ENGINE 18V 11 ENGINE FAULT DATA BUS MULTIPLE STARBOARD ENGINE 12 FAULT SENSOR FAULT OIL TEMP 13 14 15 16 46353 9. FAULT ‑ IGNITION: A problem has developed in the ignition system. 10. BATTERY: The electrical system is not charging or the battery charge is low. 11.
PRODUCT OVERVIEW 16. OIL TEMP: The engine oil is overheating. NOTE: Depending on the engine model and vessel options, not all screens will apply. 17 FAULT FAULT OIL PRESSURE MAP FAULT LOW FUEL 18 E 19 E 20 21 MAT F LOW OIL FAULT 22 TPS F SYS FAULT OBD SERVICE SOON 23 [ SHOW ] 46354 17. FAULT ‑ OIL PRESSURE: There is insufficient oil pressure. 18. LOW FUEL LEVEL: The fuel level in the fuel tank is critically low. Stop for fuel immediately to avoid running out. 19.
PRODUCT OVERVIEW Display Screens Tachometer Display Screen Engine Break‑in (2‑Stroke outboard only) Clock ‑ Air/Sea Temp Engine Temperature Fuel Used Oil Temperature Cog ‑ If there is a GPS input Oil PSI Distance and Fuel to Waypoint Trim and RPM Speed Trim and Water Pressure Estimated Range Water Pressure Instant and Average Fuel Economy Battery Voltage and Engine Hours Trip Odometer Fuel Flow and Fuel Used Fuel Tank Levels Speed and Sea Temperature Oil Tank Levels Battery Voltage Fres
SC 1000 TACHOMETER System Tachometer Display Screens When the ignition is turned on, the tachometer will display the last screen that was visible before the ignition was turned off. Press "MODE/SELECT" to change display screens. Revert back to the previous screen by pressing and holding "MODE/ SELECT" for two seconds. NOTE: Readings can be displayed in English (U.S.) or metric. Refer to Tachometer Screens. NOTE: Depending on the engine model and vessel options, not all screens will apply.
SC 1000 TACHOMETER 6. Water Pressure: Displays the cooling system water pressure at the engine. 7. Battery Voltage: Displays the voltage level (condition) of the battery. Also records the running time of the engine. FUEL GPH 8 USED 4.5 12.5 3500 9 RPM MAINTENANCE 10 OK 11 [ENTER] 35 FT SPEED SEA TEMP 12 45 13 BAT TMP PSI OK OK OK 14 - 45 F MPH 12.5 v 50352 8. Fuel Flow: Displays fuel use in gallons or liters per hour, and overall amount of fuel used. 9.
SC 1000 TACHOMETER 11. Water Depth: Displays the water depth under the transducer if connected. The water depth screen can be turned on or off in Tachometer Screens. The alarm can be set to trigger whenever the boat moves into water shallower than the alarm level. Refer to Tachometer Screens for water depth alarm and offset settings. NOTE: A depth transducer (purchased separately) must be connected to the system for this screen to operate. 12.
SC 1000 TACHOMETER Maintenance Screen Some 4‑stroke power package models have the ability to estimate the amount of run time the engine accumulated since the last scheduled maintenance. Normal scheduled maintenance for the engine is 100 hours. The maintenance screen shows a bar graph approximating the amount of time remaining before a scheduled maintenance is required. When the maintenance screen is reset, the bar graph will change to represent the scheduled maintenance has 100 hours remaining.
SC 1000 TACHOMETER 3. If the amount of time since the last scheduled maintenance has passed 100 hours, the screen will show "PERFORM SCHEDULED MAINTENANCE" and the bar graph will not be visible. Press "EXIT" to return to the previous screen or "RESET." 4. After pressing "RESET" the screen goes to the "MAINTENANCE" screen. The "MAINTENANCE" screen will display "HAS SCHEDULED MAINT. BEEN PERFORMED?" Press "YES" to reset the maintenance schedule, or press "NO" to return to the previous screen. 5.
SC 1000 TACHOMETER Tachometer Menu SPEED CONTROL TROLL CONTROL ? ENABLED [ NO ] [SAVE] [ YES ] 52680 LIGHT [DOWN] [SAVE] [ UP ] Troll control must be enabled on the tachometer to use engine RPM. Using engine RPM to control the troll function will cause the vessel speed to vary based on conditions the vessel encounters: wind, waves, or current. Adjusts the brightness of the gauge lighting. 23517 CONTRAST [DOWN] [ UP ] [SAVE] Adjusts the contrast of the display screen.
SC 1000 TACHOMETER Tachometer Menu LOCAL LIGHT [DOWN] [SAVE] [ UP ] 52644 Allows you to control the light level of the local screen. Tachometer Screens This calibration turns the system screens on and off. NOTE: Depending on the engine model and vessel options, not all screens will apply. 1. Press and hold the "MODE/SELECT" and "+" buttons for approximately seven seconds until "SCREENS" appear. 2. Press the "–" or "+" button to select the option choice displayed in the [ ] brackets on the screen. 3.
SC 1000 TACHOMETER Tachometer–Display Screens TRIM AND PSI SCREEN ? [ NO ] [SAVE] [ YES ] 23788 The split screen showing trim angle and water pressure is displayed "YES" for on or off "NO." WATER PSI SCREEN ? [ NO ] [SAVE] [ YES ] 23789 TRIM AND RPM SCREEN ? [ NO ] [SAVE] [ YES ] 23979 The water pressure screen is displayed "YES" for on or off "NO." The split screen showing trim angle and engine RPM is displayed "YES" for on or off "NO.
SC 1000 TACHOMETER Tachometer–Display Screens SEA TEMP OFFSET (DOWN ) = (SAVE) O F ( UP ) 30242 Sea temperature sensor error correction. Press "DOWN" or "UP." DEPTH SCREEN ? [ NO ] [SAVE] [ YES ] 23984 REMOTE SCREENS ? [ NO ] [SAVE] [ YES ] 52645 The depth screen is displayed "YES" for on or off "NO." Allows all SC1000 tachometers that are enabled (YES) to show the same screen. When station 1 tachometer has depth on the screen, station 2 tachometer will show the same screen.
SC 1000 TACHOMETER • • Performing the tank calibration procedure without adding fuel; the system will supply an estimated range value based on linear interpolation of the sensor range values. This mode does not factor in irregular tank shapes. You must edit the tank calibration by entering a numerical value for the capacity of the fuel tank. The linear readout is based on raw sensor values.
SC 1000 TACHOMETER Tank Calibration FILL TANK TO ½ THEN PRESS PLUS BUTTON [SAVE] 30428 Fill the tank to 1/2 full. Press the "+" button to save the calibration level to 1/2 full. FILL TANK TO 3/4 THEN PRESS PLUS BUTTON [SAVE] 30429 Fill the tank to 3/4 full. Press the "+" button to save the calibration level to 3/4 full. FILL TANK TO FULL THEN PRESS PLUS BUTTON [SAVE] 30430 CALIBRATION TANK 2 INPUT OIL TANK [DOWN] [SAVE] [ UP ] 52652 Fill the tank to full.
SC 1000 TACHOMETER Fuel Used Calibration FUEL USED CAL : MULTIPLIER = 1.0 [SAVE] [ UP ] [DOWN] 30167 FUEL USED CAL : AMOUNT REFUELED = 0.0 G [SAVE] [ UP ] [DOWN] 30168 Adjusts multiplier between 0.50 and 1.50. Press "–" to select "DOWN," or "+" to select "UP." The multiplier is used to fine‑tune the fuel gauge sender to correct for fuel used errors. If the gauge indicates that 10 gallons of fuel was used, but the actual fuel that was added is 14 gallons, change the multiplier to 1.40.
SC 1000 TACHOMETER Tachometer Calibration ‑ External Sensors CALIBRATION EXTERNAL SENSORS PITOT SENSOR ? YES [ NO ] [SAVE] [YES ] 52654 Is the boat equipped with a pitot sensor to measure boat speed? Press "–" to select "NO" or "+" to select "YES." CALIBRATION EXTERNAL SENSORS PADDLE SENSOR ? YES [ NO ] [SAVE] [YES ] 52655 Is the boat equipped with a paddle wheel to measure boat speed? Press "–" to select "NO" or "+" to select "YES.
SC 1000 TACHOMETER Tachometer Calibration ‑ External Sensors CALIBRATION TRIM FULL DOWN THEN PRESS PLUS BUTTON [DFLT] [SKIP] [SAVE] Trim the system to the full down position, then press the "+" button to save the setting. 52662 CALIBRATION TRIM FULL UP THEN PRESS PLUS BUTTON [DFLT] [SKIP] [SAVE] 52663 Trim the system to the full up position, then press the "+" button to save the setting.
SC 1000 TACHOMETER Tachometer Calibration ‑ External Sensors CALIBRATION DEPTH SENSOR OFFSET = 3 FEET [DOWN] [SAVE] [ UP ] 52676 CALIBRATION DEPTH ALARM LEVEL = 2.5 FEET [DOWN] [SAVE] [ UP ] 52677 SPEED UNITS [DOWN] MPH [ UP ] 23540 [SAVE] DISPLAY UNITS ENGLISH [DOWN] [ UP ] 23539 [SAVE] Electronically configure a depth offset. Entering a negative number gives you a waterline offset. A positive number gives you a keel offset. Press "–" or "+" to calibrate the depth sensor offset "DOWN" or "UP.
SC 1000 SPEEDOMETER Speedometer Display Screens NOTE: Depending on the engine model and vessel options, not all screens will apply. 1 2 5:30 PM F 70 60 SEA F AIR 90 GAL FUEL 1 E 30 40 50 F 20 60 10 3 110GAL FUEL 2 E 0 F 70 SPEED 80 TABS 4 0% PORT INST 5 1.5 RESET M/G 0% STBD AVG 3.2 46451 When the ignition is turned on, the speedometer will show the last screen that was displayed before the ignition was turned off. Press "MODE/SELECT" to change display screens.
SC 1000 SPEEDOMETER 4. Tabs: Shows the position of the port and starboard tab viewed as a percentage. 5. Fuel Economy: Displays the average "AVG" fuel consumption as well as instantaneous "INST" fuel economy. The numbers displayed indicate miles per gallon "M/G" or kilometers per liter "KM/L." Fuel Reset: To reset, select the display screen, press "MODE/SELECT" and "–" simultaneously. NOTE: Depending on the engine model and vessel options, not all screens will apply.
SC 1000 SPEEDOMETER 8. Speedometer: Displays the boat speed in miles per hour, kilometers per hour, or nautical miles per hour. The speedometer will use the paddle wheel for its low‑speed readings and will switch to the pitot or GPS (if connected) for high‑speed readings. 9. Fuel Used: Displays the amount of fuel used since the gauge was last reset to zero. Reset: To reset the fuel used screen, press "MODE/SELECT" and "–" simultaneously. 10.
SC 1000 SPEEDOMETER Speedometer Calibration Menu–Speed Control, Light, Contrast, and Time 46359 SPEEDOMETER CALIBRATION MENU 1. Press the "MODE/SELECT" and "+" buttons simultaneously for approximately two seconds or until the "MENU" screen appears. 2. Press "MODE/SELECT" to "SKIP" the speed control and advance through the calibration menu. 3. Press the "+" or "–" to change the settings.
SC 1000 SPEEDOMETER Calibration Menu REMOTE LCD LIGHT ? [SAVE] [ NO ] [YES ] 23532 REMOTE LCD CONTRAST ? [SAVE] [ NO ] [YES ] 23533 SPLASH SCREEN MERCURY [SKIP] [ EDIT ] 46447 SPLASH SCREEN _MERCURY [DOWN] [NEXT] [ UP ] 30246 LOCAL LIGHT [DOWN] [SAVE] [ UP ] 52644 Adjusts the lighting levels on all gauges simultaneously from this gauge. If "YES" is selected, then lighting level changes made on this tachometer will effect all tachometers in the system.
SC 1000 SPEEDOMETER Calibration Menu ( NO ) CALIBRATION USE GPS TIME DISABLED ( SKIP ) ( YES ) 46461 CALIBRATION UTC ZONE UTC CORRECTION = 0 H [DOWN] [SAVE] [ UP ] 30197 CALIBRATION HOUR PM (DOWN) 1:42 (SAVE) ( UP ) 23536 CALIBRATION MINUTE PM (DOWN) 1:42 (SAVE) ( UP ) 23538 When a GPS is installed and the GPS is enabled, the speedometer will display time received by the GPS. This is useful to automatically update the time when crossing time zones.
SC 1000 SPEEDOMETER Speedometer Display Screens WAYPOINT ALARM ? YES ( SAVE ) ( NO ) ( YES ) 46463 WAYPOINT ALARM DISTANCE = 0.3 MILES ( SAVE ) ( UP ) ( DOWN ) 46464 Waypoint alarm is displayed "YES" for on or off "NO." GPS screens must be turned on for this screen to be activated. Set the distance from the waypoint when the alarm will become active. Press the "–" button to decrease the distance or "+" to increase the distance. The default distance setting is 0.3 mile STEERING ANG.
SC 1000 SPEEDOMETER Speedometer Display Screens SCREENS [ NO ] EXIT ? [ YES ] [CAL ] 52646 Select "NO" to go through the screen selection again, "YES" to exit the screens, or "CAL" to calibrate the tank levels. Refer to Calibration–Fuel Used. CALIBRATION–FUEL USED 1. Press the "MODE/SELECT" and "+" buttons simultaneously for approximately seven seconds until "SCREENS" is display screen. 2.
SC 1000 SPEEDOMETER Fuel Used FUEL USED CAL : AMOUNT REFUELED = 0.0 G [SAVE] [ UP ] [DOWN] 30168 Adjusts fuel used calibration using the amount of fuel replaced. Press "–" to select "DOWN," or "+" to select "UP." The fuel option functions the same as the multiplier. If the gauge indicates that 10 gallons of fuel was used, but the actual fuel that was added is 14 gallons, change the amount refueled to 14.0.
SC 1000 SPEEDOMETER External Sensors CALIBRATION EXTERNAL SENSORS USE GPS SPEED ? YES ( NO ) (SAVE) ( YES ) 52684 Use the GPS input to drive the speed display? Press "–" to select "NO" or "+" to select "YES". CALIBRATION SEA TEMP OFFSET = 0 F (DOWN) (SAVE) ( UP ) 23592 Adjust the seawater temperature sensor to correct display readings that are too high/low. Press "–" or "+" to calibrate the temperature display "DOWN" or "UP". DISPLAY UNITS 1.
SC 1000 SPEEDOMETER Simulator Mode SIMULATOR MODE [ NO ] eng NO [SAVE] [ YES ] 46443 Enables the simulation mode. (Used for demonstration purposes only.
TROLL CONTROL Troll Control Operation NOTE: The troll control feature is only available on the System Tachometer and Speedometer. 5 1 0 30 40 50 4 3 2 RPM X1000 20 6 10 7 0 60 70 80 SPEED b a b a c d e f Troll Speed On ACT SET MPH MPH PUSH SELECT TO DISENGAGE Troll Speed On ACT SET 1500 RPM 1000 RPM 12.0 10.
TROLL CONTROL When the troll control is shut off, the system will remember the set speed. When the troll control is engaged, it will return to the set speed. The display screen will revert back to the previous screen after five seconds of inactivity. Push the "+" or "–" button to reactivate the troll control display screen.
TROLL CONTROL 2. Push in either the "+" or "–" buttons to bring up the troll control display screen. 3. Press "MODE/SELECT" to engage the troll control. 4. Use the "+" and "–" buttons to set the desired speed. Use "+" to increase the set speed and use "–" to decrease the set speed. 5. If the troll speed is set to a higher speed than the troll control can maintain, the "TROLL SPEED TOO FAST" display will appear. Reduce the set troll speed. 6.
SMART TOW Cruise Control Operation NOTE: Cruise control is only available with 2007 and newer DTS engines. a - Increase set cruise RPM b - Decrease set cruise RPM c - Set cruise RPM 30 40 50 20 60 10 0 70 SPEED 80 a b c 1000 SMART TOW ON CRUISE RPM SET LAUNCH + / - TO DISENGAGE 53433 NOTE: The cruise control minimum maximum range may change depending on engine model. There are two modes of cruise control: "RPM MODE" and "SPEED MODE".
SMART TOW When the cruise control is engaged and the throttle is moved below the set cruise engine RPM or speed, the engine RPM will decrease with the throttle movement. When the throttle is moved above the set cruise speed, the cruise control will actively control the engine speed to the set cruise speed. When the cruise control is disengaged it will remember the set speed. It will return to that speed when the cruise control is engaged and the throttle is positioned beyond the set cruise speed.
SMART TOW 3. Push "+" and "–" button simultaneously to engage the cruise control. NOTE: The cruise control must be engaged for both gauges to display the active cruise control setting. CANCELING CRUISE CONTROL To cancel the cruise control: press the "+" and "–" buttons simultaneously. Precise Speed Control Calibration (Optional) The Smart Tow with GPS speedometer is capable of maintaining the speed within 0.8 km/h (0.5 MPH) of the cruise control setting.
SMART TOW Press and hold the "SELECT" button for approximately three seconds to toggle between "SPEED MODE" and "RPM MODE". IMPORTANT: Only the Smart Tow Speedometer can toggle between cruise control "RPM MODE" and "SPEED MODE". Smart Tow Tachometer can change from "SPEED MODE" to "RPM MODE" only. ENGAGING THE CRUISE CONTROL 1. Push either the "+" or "–" button to bring up the cruise control display screen. 2. Set the speed to 10 MPH. 3. Push "+" and "–" button simultaneously to engage the cruise control.
SMART TOW Launch Control Operation NOTE: Launch control is only available with 2007 and newer DTS engines. a - Raise launch control setting b - Lower launch control setting c - Set cruise RPM d - Launch control setting 30 40 50 20 60 10 0 70 SPEED 80 b a c d 1000 SMART TOW ON 5 RPM SET LAUNCH + / - TO DISENGAGE 53436 BASIC OPERATION Launch control determines how fast the engine accelerates to a set cruise speed.
SMART TOW Set the launch control with either the Smart Tow Tachometer or Smart Tow Speedometer. The settings are 1, 2, 3, 4, and 5, with 1 the most gradual acceleration and 5 the most aggressive. Press "SELECT" once to highlight the launch control setting. Press "+" to increase launch control setting and "–" to decrease the launch control setting. This can be accomplished in either "RPM MODE" or "SPEED MODE." The launch control setting will remain until changed.
SMART TOW IMPORTANT: Only the Smart Tow Speedometer can toggle between cruise control "RPM MODE" and "SPEED MODE." Smart Tow Tachometer can change from "SPEED MODE" to "RPM MODE" only. 1. Press "+" or "–" to bring up the cruise control display screen. 2. Push the "SELECT" button to highlight "SET LAUNCH." 3. Push "+" to raise the setting and push "–" to lower the setting. 4. Launch control will automatically turn on with the cruise control.
SMART TOW 3. Press and hold the "SELECT" button for approximately three seconds to edit the customized launch setting. 30 40 50 20 60 10 70 0 80 SPEED a b c 35.5 NEW USER RPM SET LAUNCH + / - TO DISENGAGE SMART TOW ON a - Raise launch control setting b - Lower launch control setting c - Set cruise RPM d - "SELECT" button e - Launch control setting d e 53437 Customized Launch Settings NAME RPM SET MPH SET AAAAAAA 1000 10.0 Press the "SELECT" button to edit the name.
SMART TOW Customized Launch Settings NAME RPM SET MPH SET [DOWN] AAAAAAA 4225 10.0 [EDIT] [ UP ] 30601 MPH SET [DOWN] [ OK ] [ UP ] 30609 LAUNCH OVERSHOOT DURATION [DOWN] 1.0 0% 0.0 S [EDIT] [ UP ] 30614 LAUNCH [DOWN] [ OK ] [ UP ] 30612 LAUNCH OVERSHOOT DURATION [DOWN] 4.7 0% 0.0 S [EDIT] [ UP ] 30615 OVERSHOOT [DOWN] 12 MAX : 20% [ OK ] [ UP ] 30617 LAUNCH OVERSHOOT DURATION [DOWN] 4.7 12 % 0.0 S [EDIT] [ UP ] 30619 eng Press the "–" to move the cursor to "MPH SET".
SMART TOW Customized Launch Settings DURATION [DOWN] 3.4 s [ OK ] [ UP ] 30620 OVERSHOOT DURATION EXIT 12 % 0.0 S [ OK ] [ UP ] 30621 Press "–" or "+" to edit the duration of seconds the overshoot percentage is activated. The number of seconds is between 0 and 4. Press the "SELECT" button to exit the "DURATION" edit. Press the "–" to move the cursor to "EXIT". Press the "SELECT" button to exit the launch setting or press the "+" to review and edit the customized launch settings.
