Specifications

1-24 GROUP 1-ENGINES AND EXHAUST SYSTEMS
support insulator to engine retaining
nuts (install the automatic transmis-
sion oil cooler lines bracket).
5. Install the remaining converter
or flywheel housing retaining bolts.
Install the engine rear plate lower
retaining bolts.
6. Install the starter (and auto-
matic transmission fluid filler tube
bracket).
On a car with an automatic trans-
mission, install the transmission oil
cooler lines in the bracket at the
engine block.
7. Install the exhaust manifold to
muffler inlet pipe lock washers and
nuts. Torque the nuts to specifica-
tions. Connect the engine ground
strap, the generator wires, and the
choke control cable.
On a car with an automatic trans-
mission, install the accelerator brack-
et on the intake manifold.
On a car with a manual-shift
transmission, connect the clutch re-
lease spring and rod. Adjust the
clutch pedal free travel. Install the
flywheel housing inspection cover.
8. Connect the accelerator re-
tracting spring and the accelerator
rod assembly.
9. Connect the starter cable, the
coil primary wire, the oil pressure
and temperature sending unit wires,
flexible fuel line, the heater hoses,
and the battery ground cable.
10. Install the radiator. Connect
the radiator lower hose to the water
pump and the radiator upper hose to
the radiator supply tank.
On a car with an automatic trans-
mission, connect the oil cooler lines.
11. Fill and bleed the cooling sys-
tem. Fill the crankcase. Operate the
engine at fast idle and check all hose
connections and gaskets for leaks.
On a car with an automatic trans-
mission, adjust the transmission con-
trol linkage.
12. Install the air cleaner. Install
and adjust the hood.
IN-CHASSIS REPAIR OPERATIONS
ENGINE SUPPORTS
The front supports are located on
each side of the cylinder block (Fig.
13). The rear support is located at
the transmission extension housing
(Fig. 14).
ENGINE FRONT SUPPORT
The procedures given apply to
either a right or left installation.
Removal
1. Remove the support insulator
assembly to frame nut and lock
washer.
2. Raise the engine with a jack
and a wood block placed under the
oil pan.
3. Remove the support insulator
assembly to support bracket bolts and
lock washers. Remove the support in-
sulator assembly. If only one support
is removed, loosen the other support.
Installation
1. Position the support insulator
assembly.
A1473-A
FIG. 13-Engine Front Support
2. Lower the engine. Install the
support insulator assembly to frame
lock washer and nut. Torque the nut
to specifications.
3. Install the support insulator as-
sembly to support bracket lock wash-
ers and bolts. Torque the bolts to
specifications.
4. If only one support was re-
moved, tighten the other support.
ENGINE REAR SUPPORT
Removal
1. Remove the support insulator
assembly retaining bolts and washers.
2. Raise the engine slightly to gain
clearance at the transmission. Re-
move the support insulator assembly.
Installation
1. Position the support insulator
assembly. Lower the engine.
2. Install the support insulator as-
sembly to extension housing flat
washers, lock washers, and bolts.
Torque the bolts to specifications.
MANIFOLDS
REMOVAL
1. Remove the air cleaner.
On a car with an automatic trans-
mission, disconnect the throttle con-
trol rod and the accelerating assembly
connecting link at the accelerator
bracket. Disconnect the accelerator
retracting spring at the block
mounted bracket. Remove the
bracket.
On a car with a manual-shift
transmission, disconnect the accel-
erator retracting spring and the accel-
erator rod assembly at the bellcrank.
On an engine with positive crank-
case ventilation, remove the exhaust
tube and regulator valve as an assem-
bly by disconnecting the bracket from
the intake manifold, the exhaust tube
from crankcase ventilation outlet and
the regulator valve from the rubber
connection (Fig. 16).
2. Disconnect the choke control
cable at the carburetor.
3. Disconnect the fuel inlet line
and the distributor vacuum line at
the carburetor.
4. Disconnect the muffler inlet
pipe from the exhaust manifold.
5. Remove the bolts fastening the
manifolds to the head (two manifold
I TRANSMISSION
\ EXTENSION
YV HOUSING
SUPPORT
INSULATOR
ASSEMBLY
FRAME CROSS
MEMBER
A1474-A
FIG. 14-Engine Rear Support