User`s manual
Table Of Contents
- Preface
- Chapter 1
- Introducing the Mainboard
- Chapter 2
- Installing the Mainboard
- Safety Precautions
- Quick Guide
- Installing the Mainboard in a Case
- Checking Jumper Settings
- Connecting Case Components
- Installing Hardware
- Installing the Processor
- Installing Memory Modules
- Installing a Hard Disk Drive/CD-ROM
- Installing a Floppy Diskette Drive
- Installing Add-on Cards
- Connecting Optional Devices
- Connecting I/O Devices
- Chapter 3
- Using BIOS
- About the Setup Utility
- Using BIOS
- Standard CMOS Features
- Advanced BIOS Setup Option
- Anti-Virus Protection (Disabled)
- Y2K Monitor (Disabled)
- CPU Internal Cache CPU Internal Cache (Enabled)
- External Cache (Enabled)
- CPU L2 Cache ECC Checking (Enabled)
- Quick Power On Self Test (Enabled)
- 1st/2nd/3rd Boot Device (Floppy/HDD-0/LS120)
- Boot Other Device (Enabled)
- Swap Floppy Drive (Disabled)
- Boot Up Floppy Seek (Enabled)
- Boot Up NumLock Status (On)
- ATA 66/100 IDE Cable MSG (Enabled)
- Gate A20 Option (Fast)
- Typematic Rate Setting (Disabled)
- Security Option (Setup)
- OS Select For DRAM > 64 MB (Non-OS2)
- HDD S.M.A.R.T Capability (Disabled)
- Report No FDD For WIN95 (Yes)
- Advanced Chipset Features Option
- Integrated Peripherals Option
- OnChip IDE Device
- OnChip PCI Device
- SuperIO Device
- POWER ON Function (Hot KEY)
- KB Power ON Password
- Hot Key Power ON (Ctrl-F12)
- Onboard FDC Controller (Enabled)
- Onboard Serial Port 1 (3F8/IRQ4)
- Onboard Serial Port 2 (2F8/IRQ3)
- UART Mode Select (Normal)
- UR2 Duplex Mode (Half)
- Onboard Parallel Port (378/IRQ7)
- Parallel Port Mode (ECP)
- ECP Mode Use DMA (3)
- Game Port Address (201)
- Midi Port Address (330)
- Midi Port IRQ (10)
- Init Display First (PCI Slot)
- OnChip USB Controller (All Enabled)
- USB Keyboard Support (Disabled)
- IDE HDD Block Mode (Enabled)
- Power Management Setup Option
- Power Management Timeouts
- Wake Up Calls
- ACPI Function (Enabled)
- ACPI Suspend Type (S1 (POS))
- Power Management Option (User Define)
- HDD Power Down (Disable)
- Suspend Mode (Disable)
- Video Off Option (Suspend --> Off)
- Video Off Method (DPMS Support)
- MODEM Use IRQ (3)
- Soft-Off by PWRBTN (Instant-Off)
- AC Resume Function (Always Off)
- IRQ/Event Activity Detect
- Press
to return to the previous screen. - PNP/PCI Configuration Option
- PC Health Status Option
- Frequency/Voltage Control
- Load Fail-Safe Defaults Option
- Load Optimized Defaults Option
- Set Password Option
- Save & Exit Setup Option
- Exit Without Saving
- Chapter 4
- Using the Mainboard Software
Table of Mainboard Components
Label Component
AGP1 Accelerated Graphics Port
ATX1 Power connector
AUDIO1 Mic/speaker-out header
BAT1 Three volt realtime clock battery
CASFAN1 Case fan connector 1
CD1 Primary CD-in connector
CD2 Secondary CD-in connector
CNR1 Communications Network Riser (CNR) slot
CPU SOCKET Socket 462 for AMD Athlon processor
CPUFAN1 Cooling fan for CPU
DIMM ~ DIMM3 Three 184-pin DIMM sockets
FDD1 Floppy disk drive connector
IDE 1 Primary IDE channel
IDE 2 Secondary IDE channel
J1 Case open alarm header
JP1 KB/USB power on
JP3 CPU frequency selection jumper
JP4 BIOS voltage selection jumper
JP5 BIOS protection jumper
JP6 USB2/3 power on jumper
JP7 Clear CMOS jumper
LAUDIO1 MIC/speaker-out header
LPANEL1 Second front panel header
LSJ1 Single color LED header
LUSB1 Connector for front panel USB ports
LUSB2 Connector for front panel USB ports
PANEL1 Front panel header
PCI1 ~ PCI5 Five 32-bit add-on card slots
SCR1 Smart card reader connector
SIR1 Serial infrared cable header
SJI Single-color MSG (message) LED
SPEAKER1 Speaker connector
USB2 Connector for front panel USB ports
USB3 Connector for front panel USB ports
WOL1 Wake On LAN wakeup connector
WOM1 Wake On Modem wakeup connector
Note: LED1 is usually connected to a light that indicates that the computer is
powered on. Do not install hardware or disconnect power cables while the
LED is on.
This concludes Chapter 1. The next chapter explains how to install the main-
board.
5