User`s manual
Table Of Contents
- Preface
- Chapter 1
- Introducing the Mainboard
- Chapter 2
- Installing the Mainboard
- Safety Precautions
- Quick Guide
- Installing the Mainboard in a Case
- Checking Jumper Settings
- Connecting Case Components
- Installing Hardware
- Installing the Processor
- Installing Memory Modules
- Installing a Hard Disk Drive/CD-ROM
- Installing a Floppy Diskette Drive
- Installing Add-on Cards
- Connecting Optional Devices
- Connecting I/O Devices
- Chapter 3
- Using BIOS
- About the Setup Utility
- Using BIOS
- Standard CMOS Features
- Advanced BIOS Setup Option
- Anti-Virus Protection (Disabled)
- Y2K Monitor (Disabled)
- CPU Internal Cache CPU Internal Cache (Enabled)
- External Cache (Enabled)
- CPU L2 Cache ECC Checking (Enabled)
- Quick Power On Self Test (Enabled)
- 1st/2nd/3rd Boot Device (Floppy/HDD-0/LS120)
- Boot Other Device (Enabled)
- Swap Floppy Drive (Disabled)
- Boot Up Floppy Seek (Enabled)
- Boot Up NumLock Status (On)
- ATA 66/100 IDE Cable MSG (Enabled)
- Gate A20 Option (Fast)
- Typematic Rate Setting (Disabled)
- Security Option (Setup)
- OS Select For DRAM > 64 MB (Non-OS2)
- HDD S.M.A.R.T Capability (Disabled)
- Report No FDD For WIN95 (Yes)
- Advanced Chipset Features Option
- Integrated Peripherals Option
- OnChip IDE Device
- OnChip PCI Device
- SuperIO Device
- POWER ON Function (Hot KEY)
- KB Power ON Password
- Hot Key Power ON (Ctrl-F12)
- Onboard FDC Controller (Enabled)
- Onboard Serial Port 1 (3F8/IRQ4)
- Onboard Serial Port 2 (2F8/IRQ3)
- UART Mode Select (Normal)
- UR2 Duplex Mode (Half)
- Onboard Parallel Port (378/IRQ7)
- Parallel Port Mode (ECP)
- ECP Mode Use DMA (3)
- Game Port Address (201)
- Midi Port Address (330)
- Midi Port IRQ (10)
- Init Display First (PCI Slot)
- OnChip USB Controller (All Enabled)
- USB Keyboard Support (Disabled)
- IDE HDD Block Mode (Enabled)
- Power Management Setup Option
- Power Management Timeouts
- Wake Up Calls
- ACPI Function (Enabled)
- ACPI Suspend Type (S1 (POS))
- Power Management Option (User Define)
- HDD Power Down (Disable)
- Suspend Mode (Disable)
- Video Off Option (Suspend --> Off)
- Video Off Method (DPMS Support)
- MODEM Use IRQ (3)
- Soft-Off by PWRBTN (Instant-Off)
- AC Resume Function (Always Off)
- IRQ/Event Activity Detect
- Press
to return to the previous screen. - PNP/PCI Configuration Option
- PC Health Status Option
- Frequency/Voltage Control
- Load Fail-Safe Defaults Option
- Load Optimized Defaults Option
- Set Password Option
- Save & Exit Setup Option
- Exit Without Saving
- Chapter 4
- Using the Mainboard Software
Checking Jumper Settings
The following illustration shows the location of the mainboard jumpers. Pin 1 is
labeled.
Jumper Settings
Jumper Type Description Setting (default)
JP1 3 pin KB/USB power
on
1-2: Disable
2-3: Enable
JP1
1
JP3 3 pin CPU frequency
select
1-2: 100 MHz
2-3: 133 MHz
JP3
1
JP4 3 pin BIOS voltage
select
1-2: 5V
2-3: 3.3V
JP4
1
JP5 3 pin BIOS protection 1-2: Disable
2-3: Enable
JP5
1
8