Table of Contents Introduction Instrument Cluster 4 12 Warning and control lights Gauges 12 18 Entertainment Systems 21 AM/FM stereo with CD AM/FM stereo cassette with CD AM/FM stereo with in-dash six CD Climate Controls Manual heating and air conditioning Automatic temperature control Auxiliary passenger climate control Rear window defroster 21 26 31 41 41 43 46 47 Lights 48 Driver Controls 59 Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Messag
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Lug Nut Torque Jump starting Wrecker towing Customer Ass
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications 288 290 293 298 300 306 319 319 321 323 Accessories 330 Index 332 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction BREAKING-IN YOUR VEHICLE Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. Vary your speed frequently in order to give the moving parts a chance to break in. Drive your new vehicle at least 500 miles (800 km) before towing a trailer. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter.
Introduction Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems.
Introduction Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death. Be sure to read Driving off road in the Driving chapter.
Introduction Cell phone use The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX
Instrument Cluster WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Instrument Cluster Note: Depending on which options your vehicle has, some indicators may not be present in your vehicle. Service engine soon: The Service engine soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter.
Instrument Cluster Brake system warning light: To ! P confirm the brake system warning light is functional, it will BRAKE momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your authorized dealer.
Instrument Cluster • Optional instrument cluster Engine oil pressure: Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and Specifications chapter. If the light remains ON while driving, the temperature of the engine may be too high, refer to Engine coolant in the Maintenance and specifications chapter. Engine coolant temperature: Illuminates when the engine coolant temperature is high.
Instrument Cluster Low tire pressure warning: Illuminates when your tire pressure is low. If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to ON, the light will illuminate for 3 seconds to ensure the bulb is working. If the light does not turn ON, have the system inspected by your authorized dealer.
Instrument Cluster AdvanceTrac威: Flashes when the AdvanceTrac威 with RSC system is active. Illuminates solid when the system has been disabled (by the driver or as a result of a system failure), refer to the Driving chapter for more information. All wheel drive (AWD): 4x4 Illuminates when AWD is engaged. If the light fails to illuminate when the ignition is turned ON, or remains on, have the system serviced immediately by your authorized dealer.
Instrument Cluster Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened. Turn signal warning chime: Sounds when the turn signal lever has been activated to signal a turn and not turned off after the vehicle is driven more than 2 miles (3.2 km).
Instrument Cluster Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating, refer to Engine coolant in the Maintenance and specifications chapter. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot.
Instrument Cluster • Optional instrument cluster Press and release the message center INFO button until TRIP A mode appears in the display. Press the control again to select the TRIP B feature. Press the RESET button to reset. Note: Outside Air Temperature will only be displayed in the Instrument Cluster Message Center on vehicles with manual climate control. Tachometer: Indicates the engine speed in revolutions per minute.
Entertainment Systems AUDIO SYSTEMS AM/FM Single CD/MP3 Satellite Compatible Sound System (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings.
Entertainment Systems 3. MENU: Press to toggle through the following modes: Setting the clock: Press MENU until SET HOURS or SET MINUTES is displayed. Use / to manually increase/decrease Press MENU again to disengage clock mode. CATEGORY (Satellite Radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY MODE). In CATEGORY MODE, press / to scroll through the list of available Sirius channel Categories (Pop, Rock, News, etc.
Entertainment Systems Track/Folder Mode: Available only on MP3 discs in CD mode. / to toggle between Track and Folder mode. Press In Track mode, press current disc. In Folder mode, press selected folder. SEEK SEEK to scroll through all tracks on the to scroll through tracks within the Compression: Brings soft and loud CD passages together for a more consistent listening level when in CD mode. Press MENU until / to turn the feature on/off. compression status is displayed. Press 4.
Entertainment Systems 7. SHUFFLE: Press to play tracks in random order. : In folder mode, 8. FOLDER press to access next folder on MP3 discs, if available. FOLDER: In folder mode, 9. press to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): Press to manually advance in a CD track. 11. REW (Rewind): Press to manually reverse in a CD track. 12. Memory presets: To set a station, select the desired frequency band, AM, FM1 or FM2. Tune to the desired station.
Entertainment Systems In Satellite Radio mode (if equipped), press and hold to hear a brief sampling of the next channels. Press again to stop. 14. AM/FM: Press to select AM/FM1/FM2 frequency band. 15. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 16. CD: Press to enter CD mode.
Entertainment Systems AM/FM Single CD/MP3/Cassette Satellite Compatible Sound System (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings.
Entertainment Systems In CD mode, press / to access the previous/next CD track. In Satellite Radio mode (if equipped), press SEEK to seek to the previous/next channel. If a specific category is selected, (Jazz, Rock, News, etc.), press SEEK to seek to the previous/next channel in the selected category. Press and hold SEEK to fast seek through the previous /next channels. In TEXT MODE, press SEEK to view the previous/additional display text. In CATEGORY MODE, press SEEK to select a category.
Entertainment Systems Bass: Press / / Treble: Press to adjust the treble setting. / Balance: Press speakers. Fade: Press speakers. to adjust the bass setting. / to adjust the audio between the left and right to adjust the audio between the front and rear Speed sensitive volume: Radio volume automatically changes slightly / with vehicle speed to compensate for road and wind noise. Use to adjust. Recommended level is 1–3. Level 0 (SPEED OFF) turns the feature off and level 7 is the maximum setting.
Entertainment Systems 7. Play/Pause: This control is operational in CD, tape and DVD mode (if equipped). When a CD or DVD is playing in the FES system, press this control to play or pause the current CD/DVD. The CD/DVD status will display in the radio display. 8. SHUFFLE: Press to play CD tracks in random order. 9. FOLDER : When in folder mode, press to access next folder on MP3 discs, if available. FOLDER: When in folder 10. mode, press to access the previous folder on MP3 discs, if available. 11.
Entertainment Systems 16. AM/FM: Press to select AM/FM1/FM2 frequency band. 17. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. 18. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. If no CD is loaded, NO DISC will appear in the display. 19.
Entertainment Systems Audiophile AM/FM In-dash Six CD/MP3 Satellite Compatible Sound System (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. / Tune/Disc selector: 1. Press and release to manually advance up/down the radio frequency or to select a desired disc.
Entertainment Systems 2. MUTE/Phone: Press to mute the playing media. Press again to return to the playing media. 3. MENU: Press to toggle through the following modes: Setting the clock: Press until SET HOURS or SET MINUTES is / to adjust the hours/minutes. displayed. Press CATEGORY (Satellite Radio if equipped): Press MENU until the currently active category appears in the display (CATEGORY MODE).
Entertainment Systems When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system / to turn will store the last one in the remaining presets. Use on/off. Bass: Press / / Treble: Press to adjust the treble setting. / Balance: Press speakers. Fade: Press speakers. to adjust the bass setting.
Entertainment Systems 5. Seek: Press to access the ) or next ( ) strong previous ( station or CD track. In Satellite Radio mode (if SEEK to seek to the previous/next channel. If a equipped), press specific category is selected, (Jazz, Rock, News, etc.), press SEEK to seek to the previous/next channel in the selected category. SEEK to fast seek through the previous /next Press and hold channels. SEEK to view the previous/additional In TEXT MODE, press display text. SEEK to select a category.
Entertainment Systems 12. Memory presets: To set a station, select the desired frequency band, AM, FM1 or FM2. Tune to the desired station. Press and hold a preset button until sound returns and PRESET # SAVED appears in the display. You can save up to 18 stations, six in AM, six in FM1 and FM2. In Satellite Radio mode (if equipped), there are 18 available presets, six each for SAT1, SAT2 and SAT3.
Entertainment Systems 16. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. If no CD is loaded, NO DISC will appear in the display. 17. LOAD: Press to load a CD. Press LOAD and a memory preset to load to a specific slot. Press and hold to autoload up to six CDs. 18. CD eject: Press to eject a CD. Press and hold to auto eject all CDs present in the system. If there is no CD present, the display will read NO DISC. 19.
Entertainment Systems • Allow tapes which have been subjected to extreme heat, humidity or cold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme humidity, heat or cold. • Leave tapes in the cassette player for a long time when not being played. CD/CD player care: Do: • Handle discs by their edges only.
Entertainment Systems sports, weather and traffic programming. For a complete set of SIRIUS Satellite Radio channels, visit www.sirius.com or call SIRIUS at 1.888.539.7474. For a quick reference of the SIRIUS Satellite Radio channel guide, refer to the Sirius Welcome Kit. Satellite radio reception factors: To receive the satellite signal, your vehicle has been equipped with a satellite radio antenna located on the roof of your vehicle.
Entertainment Systems Satellite Radio Electronic Serial Number (ESN): This 12 digit Satellite Serial Number is needed to activate, modify or track your satellite radio account. You will need this number when communicating with SIRIUS. While in Satellite Radio mode, you can view this number on the radio display by pressing AUX and Preset 1 control simultaneously.
Entertainment Systems Radio Display NO TEXT NO TEXT NO SIGNAL UPDATING CALL SIRIUS 1–888–539–7474 Condition Song title information not available. Action Required Song title information not available at this time on this channel. The system is working properly. Category information not Category information not available. available at this time on this channel. The system is working properly.
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Temperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. Max A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This recooling of the interior air is more economical and efficient.
Climate Controls • Remove any snow, ice or leaves from the air intake area at the base of the windshield. • To improve the A/C cool down when the vehicle interior is significantly warmer than the outside temperature, drive with the windows slightly open for 2–3 minutes after start up or until the vehicle has been “aired out.” For maximum cooling performance in panel ( ) mode: • Select MAX A/C mode. MAX A/C uses recirculated air with A/C to provide a cooler airflow.
Climate Controls DUAL AUTOMATIC TEMPERATURE CONTROL (DATC) SYSTEM (IF EQUIPPED) 14 15 16 17 1 EXT F F C 13 12 3 A/C F AUTO 2 DUAL R OFF 11 10 9 1. A/C control: Manually turns A/C on or off. 8 7 6 5 4 A/C 2. Recirculation control: Cools the vehicle more quickly by recirculating the cabin air instead of using outside air and helps prevent unpleasant outside odors or fumes from entering the vehicle. Press to turn on/off. 3.
Climate Controls 5. DUAL (Single/dual electric temperature control): Allows the driver to have full control of the cabin temperature settings (single zone) or allows the passenger to have control of their individual temperature settings (dual zone control). Press to turn on dual zone mode, press again to return to single zone. DUAL 6. : Distributes outside air through the windshield defroster vents. : Distributes outside air through the windshield defroster vents 7. and floor vents.
Climate Controls 15. Fan Speed: Manually increases or decreases the fan speed. EXT 16. EXT: Displays the outside air temperature. It will remain displayed until the EXT control is pressed again. The external temperature will be most accurate when the vehicle has been moving for a period of time. FC 17. Temperature conversion: Press to toggle between Fahrenheit and Celsius temperature on the DATC display only. The set point temperatures in Celsius will be displayed in half-degree increments.
Climate Controls Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. AUXILIARY SYSTEM (IF EQUIPPED) Your vehicle may be equipped with an auxiliary climate system. These auxiliary controls, located in the overhead console, allow the front passengers to control airflow direction, temperature and fan level of the rear compartment to quickly heat or cool the entire vehicle. Front auxiliary controls: 1.
Climate Controls FLOOR CONSOLE CLIMATE CONTROLS Controls the direction of the airflow to the rear of the vehicle. • • directs air flow primarily through the console panel register. directs air flow through the console floor register. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp Control The autolamp Control sets the headlamps to turn on and off automatically. The autolamp control, located on the headlamp control, may be set to: • turn on the lamps automatically at night • turn off the lamps automatically during the daylight • keep the lamps on for up to three minutes after the key is turned to OFF. .
Lights Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the ON position and • the headlamp control is in the or position • the transmission is not in park. Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel when exterior lights are on. • Rotate the thumbwheel from left to right to brighten the instrument panel. • Rotate the thumbwheel from right to left to dim the instrument panel. • Rotate to fully to the right (past detent) to turn on interior lamps. • Rotate to the left position (past detent) to turn off the interior lamps and will also disable the illuminated entry feature.
Lights 3. Turn on the low beam headlamps. The brightest part of the light should be below the horizontal line (4). If it is above the line the headlamp will need to be adjusted. 4. Open the hood. 5. Locate the vertical adjuster for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust down) or counterclockwise (to adjust up). Note: Use a 4 mm socket or box wrench to turn the vertical adjuster control. 6.
Lights INTERIOR LAMPS Dome/reading lamps The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF. The reading portion, the two outer lights, can only be toggled on and off at the lamp. The front map lamps are located in the overhead console (if equipped). Press the controls on either side of each map lamp to activate the lamps.
Lights Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing the interior bulbs Check the operation of the bulbs frequently. To replace any of the interior bulbs, see a dealer or qualified technician. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility.
Lights Replacing headlamp bulbs Do not touch the glass of a halogen bulb. 1. Turn off the headlamps and open the hood. 2. Remove the two retainer pins, then pull headlamp forward. 3. Remove protective cap and disconnect the electrical connector. 4. Remove the bulb retaining ring. 5. Carefully pull the old bulb out of the lamp assembly.
Lights Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Reverse steps to reinstall bulb(s). Replacing front parking/turn signal bulbs 1. Turn OFF the headlamps and open the hood. 2. Remove the two headlamp retainer pins, then pull the headlamp forward. 3. Remove the bulb socket from the lamp assembly. 4.
Lights Replacing side-mounted turn signal bulbs 1. Turn the headlamp switch to off. 2. Carefully pry the lamp assembly away from the fender. 3. Rotate the bulb socket counterclockwise to remove it from the lamp assembly. 4. Pull the bulb straight out. Reverse steps to reinstall bulb(s). Replacing front/rear side marker bulbs 1. Turn the headlamp switch to off. 2. Reach under the bumper and rotate the bulb socket counterclockwise to remove it. 3. Pull the bulb straight out.
Lights 4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly. 5. Pull the bulb straight out of the socket. Note: Disconnect the LED brake lamp from the electrical connector and replace the LED assembly. Reverse steps to reinstall bulb(s). Replacing foglamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning it counterclockwise. 3. Disconnect the electrical connector. Reverse steps to reinstall bulb(s).
Lights Replacing high-mount brakelamp bulb 1. Remove the two screws and lamp assembly away from the vehicle. 2. Remove the bulb holder from the lamp assembly by depressing the snaps. 3. Pull the bulb straight out of the socket and push in the new bulb. Reverse steps to reinstall bulb(s).
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls TILT STEERING COLUMN Pull the lever down and release, to unlock the steering column tilt lock. With the lever in the down position, tilt the steering column and wheel to its desired orientation. Do not push or pull the lever while tilting the wheel. Lift the lever back to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on the visor mirror lamps.
Driver Controls Slide on rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Storage compartment Press the latch to open the storage compartment.
Driver Controls Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Place the VELCRO威 hook onto the side of the aftermarket transmitter opposite of the button. • Place the transmitter into storage compartment, button down. • Place the provided height adaptors onto the back of the door as needed. • Close the door. • Press the depression in the door to activate the transmitter.
Driver Controls The auxiliary power point is located in the floor console. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used.
Driver Controls • Cupholders Use only soft cups in the cupholder. Hard objects can injure you in a collision. Rear center console features (if equipped) The rear center console incorporates the following features: • Utility compartment • Cupholders • Flip forward armrest to provide a flat load floor POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves.
Driver Controls Press and pull the window switches to open and close windows. • Push down (to the first detent) and hold the switch to open. • Pull up and hold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise; this noise can be eliminated by lowering a front window approximately two to three inches. One touch down Allows the driver’s window to open fully without holding the control down.
Driver Controls AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function. The electrochromic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the mirror. When the mirror detects bright light from behind the vehicle, it will automatically adjust (darken) to minimize glare.
Driver Controls Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Driver Controls Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. on the 5. The indicator light instrument cluster will turn on.
Driver Controls Resuming a set speed Press the RES (resume) control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function.
Driver Controls Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features.
Driver Controls In AM, FM1, or FM2 mode: SEEK to • Press select preset stations within the selected radio band or press and hold to select the next/previous radio frequency. In Satellite radio mode (if equipped): SEEK to • Press advance through preset channels or subscribed channels. In Tape mode: SEEK to select the next selection on the tape or • Press press and hold to forward or reverse the tape.
Driver Controls Climate control features (if equipped) Press TEMP + or - to adjust temperature. Press FAN + or - to adjust fan speed. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up (from the closed position) to ventilate the vehicle. Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.
Driver Controls To close the moon roof: The moon roof is equipped with an automatic, one-touch, express closing feature. Press and release the front portion of the control. To stop motion at any time during the one-touch closing, press the control again. Bounce back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automatically open and stop at a prescribed position.
Driver Controls When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
Driver Controls 3. Simultaneously press and hold both the HomeLink威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” section for Canadian residents. 4. The indicator light will flash slowly and then rapidly. Release both buttons when the indicator light flashes rapidly.
Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Steps 1 and 2 outlined in the “Programming” section, replace Step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating.
Driver Controls Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 2 in the “Programming” section.
Driver Controls Selectable features Press and release the TRIP/RESET control switch to scroll and reset the following functions. Select or reset a function by holding the TRIP/RESET button for more that 2 seconds. Info menu This menu displays the following control displays: • Odometer/Trip Odometer (Trip A and Trip B) • Distance to Empty • Average Fuel Economy • Setup Menu Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter.
Driver Controls Average fuel economy (AFE) Select this function to display your average fuel economy in miles/gallon or liters/100 km.
Driver Controls Briefly press the TRIP/RESET control switch to scroll through the SETUP MENU display sequence. If the TRIP/RESET control switch is not pressed within 4 seconds, the message center returns to the Info Menu. AWD lock (vehicles equipped with AdvanceTrac姞 with RSC only) Select this function from the SETUP MENU to display the AWD locked function. 1. Press the TRIP/RESET control for the current display mode. 2.
Driver Controls 5. EXTERIOR LAMP 6. BRAKE SYSTEM 7. PARK BRAKE 8. MILES TO EMPTY 9. FUEL LEVEL LOW (will only display if 50 miles or less to empty) To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Enter SYSTEM CHECK to display “HOLD RESET IF NEW OIL”. 2. Press and hold the RESET control switch for more than 2 seconds. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed.
Driver Controls 1. Select this function from the SETUP MENU for the current language to be displayed. 2. Press and hold the TRIP/RESET control to select a new language. Selectable languages are English, Spanish, French, Japanese, or Arabic. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU. Autolamp This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1.
Driver Controls 1. To disable/enable the autounlock feature, select this function from the SETUP MENU. 2. Press and hold the TRIP/RESET control switch to turn the autounlock ON or OFF. 3. Press the TRIP/RESET control switch for the next SETUP MENU item or wait for more than 4 seconds return to the INFO MENU. Reverse Sensing System (Park Aid) (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1.
Driver Controls The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone adjustment.
Driver Controls 4. Press and hold the reset button on the compass module for approximately 4 seconds until COMPASS ZONE XX appears in the message center display. 5. Continue to press the reset button until the correct zone appears in the message center display. 6. After 4 seconds ZONE IS SET will appear in the message center display. 7. The display will return to normal operation. The zone is now updated.
Driver Controls In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.
Driver Controls DOOR AJAR. Displayed when a door is not completely closed. CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage when the engine is running. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. FUEL LEVEL LOW.
Driver Controls CHECK HIGHBEAM LAMP. Displayed when the highbeam lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. CHECK TURN LAMP. Displayed when the turn lamps are activated and at least one bulb is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. Refer to Replacing headlamp bulbs in the Lights chapter. WASHER FLUID LEVEL LOW.
Driver Controls Your display can show up to 6 reconfigurable telltales at one time. What ever is displayed in the top left corner has the highest priority. Selectable features Reset Press this control to select and reset functions shown in the INFO menu, SETUP menu, text warnings and reconfigurable telltale warnings. Info menu The Info menu items are shown on the top two lines of the message center.
Driver Controls Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty.
Driver Controls 2. Record the highway fuel economy for future reference. It is important to press the RESET control (press and hold RESET for 2 seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a Bar Graph ranging from poor fuel economy excellent fuel economy.
Driver Controls Blank display Select this function from the INFO menu to turn the upper two lines of the message center display OFF.
Driver Controls System check Selecting this function from the SETUP MENU causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. OIL LIFE RESET 2.
Driver Controls • Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed. Note: To change oil life 100% miles value from 5,000 miles (8,000 km) and 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section. Units (English/Metric) 1. Select this function from the SETUP MENU for the current units to be displayed. 2. Press the RESET control to change from English to Metric. 3.
Driver Controls 1. To change the delay time of the autolamp feature, select this function from the SETUP MENU. 2. Press the RESET control to select the new Autolamp delay time (in seconds) value of 0, 10, 20, 30, 60, 90, 120 or 180 and wraps back to 0. Selecting 0 will result in no delay feature. Note: “>” in front of a number indicates current selection. 3. Press the RESET control for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO menu.
Driver Controls Running Boards (if equipped) This feature automatically deploys the side running boards for easy entry/exit from the vehicle or for cleaning. Refer to Running boards in the Driver Controls chapter for more information. 1. To change operation of the power running board feature, select this function from the SETUP MENU. 2.
Driver Controls Reverse Sensing System (Park Aid) (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reverse sensing system feature with the vehicle in P (Park), select this function from the SETUP MENU or put the vehicle in R (Reverse). 2. Press the RESET control to turn the park aid ON or OFF. 3.
Driver Controls Compass zone adjustment 1. Determine your magnetic zone by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 3 2 1 15 4 14 13 5 12 6 4. From SETUP MENU, select compass zone. 5. Press RESET control until the message center display changes to show the current zone setting (XX). 6. Press the RESET control repeatedly until the correct zone setting for your geographic location is displayed on the message center.
Driver Controls Compass calibration adjustment. Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. From the SETUP MENU, press the SETUP control to select the compass calibration function. 2. Press RESET for calibration. 3.
Driver Controls System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages.
Driver Controls Warning display Check park aid (if equipped) Low tire pressure Tire monitor fault Tire sensor fault Brake fluid level low Check headlamp Check highbeam lamp Check turn lamp Washer fluid level low Oil change required Engine oil change soon Liftgate/glass ajar Status Warning returns only after the ignition key is turned from OFF to ON. Warning returns after the condition has cleared then reoccures within the same ignition ON-OFF cycle. DOOR AJAR.
Driver Controls TIRE MONITOR FAULT. Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, have the system inspected by your authorized dealer. TIRE SENSOR FAULT. Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter.
Driver Controls RUNNING BOARDS (IF EQUIPPED) Deployable running boards (DRB) automatically move when the doors are opened to assist entering and exiting the vehicle. Automatic power deploy: • The running boards will extend down when the doors are opened. Automatic power stow: • The running boards will return to the stowed position when the doors are closed. Manual power deploy: To manually operate the running boards, refer to the Message Center in this chapter.
Driver Controls Note: If the battery is disconnected, the power running boards default to the OFF mode. The running boards must be turned on again, refer to Message Center in this chapter. Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board under body mounts to lift the vehicle with the jack, refer to Changing Tires in the Roadside Emergencies chapter. In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy.
Driver Controls CARGO COVER (IF EQUIPPED) Your vehicle may be equipped with a cargo area cover that covers the luggage compartment of your vehicle. To install the cover: Push both ends of the cover into the depressions (right side first) in the trim panels behind the second row seat. To reduce the risk of injuries, the cargo area cover must be properly installed on the rear trim panels. Do not place any objects on the cargo area cover.
Driver Controls 5 passenger stowage: When the lid is open, it will stand up on its own. 1. To open, lift the release handle and the lid. 2. To close, lower the lid, lift the release handle and press down on the lid. REAR LIFTGATE The liftgate area is only intended for cargo, not passengers. You can open and close the liftgate from outside the vehicle. It cannot be opened from inside the cargo area.
Driver Controls Make sure the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also reduce the risk of passengers and cargo falling out. LUGGAGE RACK Your vehicle is equipped with a roof rack. The maximum recommended load is 100 lbs (45 kg), evenly distributed. Use the tie down loops on the thumbwheels (if equipped) to secure the load. To adjust cross-bar position (if equipped): 1.
Locks and Security KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer. Refer to the SecuriLock娂 passive anti-theft system section later in this chapter for more information.
Locks and Security Power door lock/unlock inhibit feature (if equipped) If the key is not in the ignition, all doors are closed, and the vehicle has been locked using the remote entry transmitter, keypad (if equipped) or the power door unlock control on the door panel while a front door is open (then subsequently closed), the power door unlock control on the door panel will become disabled 20 seconds after the lock event occurred.
Locks and Security CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage the childproof lock. • Move control down to disengage childproof locks.
Locks and Security The remote entry system allows you to lock or unlock all vehicle doors and liftgate, open the liftgate window without a key and activate the panic alarm. The remote entry lock/unlock feature operates in any ignition position. The liftgate glass feature operates as long as the vehicle’s speed is less than 3 mph (5 km/h). The panic feature operates with the key in the 1 (OFF/LOCK) position.
Locks and Security Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can be switched between two step and one step door unlocking by pressing and and buttons simultaneously on the remote entry holding both the transmitter for approximately 4 seconds. The parklamps will flash twice to indicate that the vehicle has switched to one step unlocking. Repeat the procedure to switch back to two-step unlocking. Locking the doors/liftgate 1.
Locks and Security Activating the memory seat feature To activate this feature: 1. Position the seat and adjustable pedals to the position desired. 2. Press the SET control on the lower-center portion of the instrument panel. 3. Within 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the lower-center portion of the instrument panel which you would like to associate with the seat and Driver 1 or Driver 2 positions. 4.
Locks and Security 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity. 5. Snap the two halves back together.
Locks and Security To reprogram the remote entry transmitters: 3 2 4 1 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (OFF/LOCK) position to 3 (ON). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (OFF/LOCK) position and 3 (ON). Note: The eighth turn must end in the 3 (ON) position. 5. The doors will lock, then unlock, to confirm that the programming mode has been activated. 6.
Locks and Security The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 10 minutes after the ignition has been turned to the 1 (OFF/LOCK) position. KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without using a key. • open the liftgate window. • activate or deactivate the autolock feature.
Locks and Security Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal code. • If you program a code to a position that already contains a set code, the previously-set code will be erased. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad and release. 3. Press and hold the 1 • 2 for two seconds.
Locks and Security Autolock The autolock feature will lock all the doors, liftgate and liftgate window when: • all doors are closed, • the ignition is in the 3 (ON) position, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h).
Locks and Security 4. Press the power door unlock control three times. 5. Turn the ignition back to the 3 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the 1 (OFF/LOCK) position. The horn will chirp once to confirm the procedure is complete. Keyless entry key pad procedure 1.
Locks and Security Deactivating/activating autounlock Your vehicle comes with the autounlock feature activated. There are four methods to enable/disable this feature: • Through your authorized dealer, or • Performing the power door lock control procedure, or • Performing the keyless entry key pad (if equipped) procedure, or • Performing the message center (if equipped) procedure.
Locks and Security 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Message center procedure For information on activating/deactivating the autounlock feature using the vehicle’s message center (if equipped), refer to Message center information in the Driver Controls chapter.
Locks and Security If a problem occurs with the SecuriLock娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for service. Automatic arming The vehicle is armed immediately 3 after switching the ignition to the 2 (ACCESSORY) position. 2 The theft indicator will flash every 4 two seconds when the vehicle is armed.
Locks and Security • If two previously programmed coded keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed. Please read and understand the 3 entire procedure before you begin. 1. Insert the first previously 2 programmed coded key into the 4 ignition. 1 2. Turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position. Keep the ignition in the 3 (ON) position for at least three seconds, but no more than 10 seconds. 3.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward.
Seating and Safety Restraints Pull lever up to adjust seatback. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seatback, with your feet on the floor.
Seating and Safety Restraints Press the control to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward. Memory seats and adjustable pedals (if equipped) This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions. The memory seat control is located on the lower-center portion of the instrument panel.
Seating and Safety Restraints The memory positions are also recalled when you press your remote entry transmitter UNLOCK control if the transmitter is programmed to a memory position or when you enter a valid personal entry code that is programmed to a memory position. To program the memory feature to a remote entry transmitter and for more information on how to use the keypad, refer to Remote entry system and Keyless entry system in the Locks and Security chapter.
Seating and Safety Restraints REAR SEATS Folding down the 2nd row 60/40 seats and bucket seats Ensure that the head restraint is in the down position and no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down. 1. Lower the head restraints by pulling on the strap. 2. Locate handle on the side of the seat cushion by the door. 3. Pull up on the handle and push the seatback forward toward the front of the vehicle.
Seating and Safety Restraints 3. Lift up on the head restraint until it locks into its original position. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
Seating and Safety Restraints Returning to the upright position from full lowered load floor position The seatback cannot be returned to the upright position until the seat is returned from the kneel down position. To return the seat to the upright position: 1. Push the seat rearward until the latch is engaged. 2. Return the seatback to the upright position. Adjusting the 2nd row seat for E-Z Entry The E-Z entry seat allows for easier entry and exit to and from the 3rd row seat.
Seating and Safety Restraints To return the seat to a seating position: 1. Push the seat down and latch to the floor with a moderate amount of effort and speed. 2. Make sure the seat is latched to the floor. 3. Bring the seat back to an upright position. The seatback should lock into position. Note: If the seat back will not return to the upright position, tumble the seat again and re-latch it to the floor. Be sure that cargo or other objects are not trapped underneath the seatback.
Seating and Safety Restraints 3rd row folding seat (if equipped) Before folding the third row seats, fold the head restraints down by pulling on the strap located under the restraint. Pull up on the handle located behind the seatback while pushing the seatback forward and down into the seat cushion. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints The control buttons are located on the driver-side rear quarter trim panel (accessible from the liftgate area). Push the bottom portion of the control button to lower the desired seatback. Push the top of the control button to return the seatback to its original position. The power fold down seats will operate for 30 minutes after the ignition switch is in the 1 (OFF/Lock) position. The transmission must be in P (Park), and the liftgate, or liftgate glass must be open.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision.
Seating and Safety Restraints The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system. Rather, it means the Personal Safety System娂 determined the accident conditions (crash severity, belt usage, etc.) were not appropriate to activate these safety devices.
Seating and Safety Restraints Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The front passenger sensing system can automatically turn off the front passenger airbag and passenger seat-mounted side airbag.
Seating and Safety Restraints Determining if the Personal Safety System姟 is operational The Personal Safety System娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the Personal Safety System娂 is not required.
Seating and Safety Restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. To unfasten, push the release button and remove the tongue from the buckle. • Front and rear seats All safety restraints in the vehicle are combination lap and shoulder belts.
Seating and Safety Restraints Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions.
Seating and Safety Restraints • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Unbuckle the combination lap and shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and Safety Restraints Refer to the Safety belt maintenance section in this chapter. Front safety belt height adjustment Your vehicle has safety belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down.
Seating and Safety Restraints To adjust the comfort guide: 1. Slip the shoulder belt into the belt guide. 2. Slide the guide up or down along the webbing so that the belt is centered on the occupant’’s shoulder. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20 cm) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from an authorized dealer.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...
Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” Consider... 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers.
Seating and Safety Restraints Reasons given... “I have an airbag” “I’d rather be thrown clear” Consider... Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on top of a buckled safety belt to avoid the BeltMinder威 chime.
Seating and Safety Restraints The driver and front passenger BeltMinder威 features can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: • The parking brake is set • The gearshift is in P (Park) (automatic transmission) • The ignition switch is in the OFF position • The driver and front passenger safety belts are unbuckled To reduce the risk of injury, do not deactivate/activate the BeltMinder威 feature while driving the vehicle. 1.
Seating and Safety Restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary.
Seating and Safety Restraints Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Airbags DO NOT inflate slowly; there is a risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided.
Seating and Safety Restraints Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses. See your authorized dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and non-Ford tow hooks may effect the performance of the airbag sensors increasing the risk of injury. Do not modify the front end of the vehicle with anything other than authorized Ford accessories for your vehicle.
Seating and Safety Restraints How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags). • seat-mounted side airbags (if equipped).
Seating and Safety Restraints The front passenger sensing system will disable (will not inflate) the front passenger’s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat, • the system determines that an infant is present in a rear-facing infant seat that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’s in
Seating and Safety Restraints • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the full upright position.
Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below. Objects Pass Airbag Off Indicator Lamp Unlit Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or “pass airbag off” indicator lamp for proper airbag Status.
Seating and Safety Restraints Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required.
Seating and Safety Restraints Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
Seating and Safety Restraints The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints Do not lean your head on the door. The Safety Canopy娂 could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the Safety Canopy娂 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy娂. See your authorized dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy娂 system is provided.
Seating and Safety Restraints • A headliner that will flex to open above the side doors to allow Safety Canopy娂 deployment. • The same warning light, electronic control and diagnostic unit as used for the front airbags. • Two side crash sensors mounted at the front doors (one on each side of the vehicle). • Two side crash sensors located at the c-pillar behind the rear doors (one on each side of the vehicle). • Roll over sensor in the restraints control module (RCM).
Seating and Safety Restraints If the Safety Canopy娂 system has deployed, the Safety Canopy娂 will not function again. The Safety Canopy娂 system (including the A, B and C pillar trim) must be inspected and serviced by an authorized dealer. If the Safety Canopy娂 is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system.
Seating and Safety Restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old.
Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury in a crash.
Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat.
Seating and Safety Restraints Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle.
Seating and Safety Restraints tether anchors. For more information on top tether straps and anchors, refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. The rear seats of your vehicle are equipped with built-in tether strap anchors located behind the seats as shown below.
Seating and Safety Restraints 1. Position the child safety seat on the rear seat cushion. 2. Route the tether strap under the head restraint and between the head restraint posts. 3. Locate the correct anchor for the selected rear seating position. When placing a child safety seat in the 2nd row center seating position of the 5 passenger vehicle, the tether straps may be attached to either of the tether anchors located at the rear of the cargo area.
Seating and Safety Restraints 4. Clip the tether strap to the anchor. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the LATCH anchors or safety belts. Follow the instructions in this chapter. 6. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and Safety Restraints • 5 passenger vehicle • 6 passenger vehicle • 7 passenger vehicle Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the second row seat between the cushion and seat back. The LATCH anchors are below the locator symbols on the seat back. ’The anchors on the 2nd row outboard seats are provided only to install child seats at the outboard seats.
Seating and Safety Restraints If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the child seat just touching the vehicle seat gives the best protection in a severe crash. Each time you use the safety seat, check that the seat is properly attached to the lower anchors and tether anchor.
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Utility vehicles have a significantly higher rollover rate than other types of vehicles.
Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and Specifications chapter. You should become thoroughly familiar with this information before you operate your vehicle.
Tires, Wheels and Loading • Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car.
Tires, Wheels and Loading government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. Traction AA A B C The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for Metric tires].
Tires, Wheels and Loading At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company. Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate.
Tires, Wheels and Loading If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recommended cold pressures. A hot tire at or below recommended cold inflation pressure could be significantly under-inflated. To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety, tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail.
Tires, Wheels and Loading U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall. This begins with the letters “DOT” and indicates that the tire meets all federal standards.
Tires, Wheels and Loading on the tire sidewall). Additionally, if your vehicle was originally equipped with run-flat tires, replacing them with tires that are not identical to those originally fitted may cause malfunction of the TPMS, and is not recommended. Run-flat tires should not be used to replace regular tires. Always check your TPMS indicator immediately after replacing one or more tires on your vehicle. If the TPMS indicator is flashing, your TPMS is malfunctioning.
Tires, Wheels and Loading vehicle seems to pull to one side when you’re driving, the wheels may be out of alignment. Have an authorized dealer check the wheel alignment periodically. Wheel misalignment in the front or the rear can cause uneven and rapid treadwear of your tires and should be corrected by an authorized dealer. Front wheel drive (FWD) vehicles and those with an independent rear suspension (if equipped) may require alignment of all four wheels. The tires should also be balanced periodically.
Tires, Wheels and Loading Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire/wheel it is intended for temporary use only and should not be used in a tire rotation. Note: After having your tires rotated, inflation pressure must be checked and adjusted to the vehicle requirements.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading When your temporary spare tire is installed (if equipped) When one of your road tires needs to be replaced with the temporary spare (T-type spare/Mini spare or Dissimilar spare), the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle. During this time, the low tire warning light can periodically return or stay on, depending on the state of the damaged road wheel/tire.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1. Check your tire pressure to under-inflated ensure tires are properly inflated; refer to Inflating your tires in this chapter. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge for increased accuracy. 2.
Tires, Wheels and Loading Low Tire Pressure Possible cause Warning Light Flashing Warning Spare tire in use Light (flashes for a short time either at start-up or while driving) TPMS malfunction Customer Action Required Your temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to Changing tires with TPMS in this section.
Tires, Wheels and Loading How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. The pressure in each tire is dependent upon several factors, one of them being the contained air temperature (temperature of the air inside the tire). As the contained air temperature increases, the tire pressure also increases.
Tires, Wheels and Loading USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction in rain and snow. However, in some climates, using snow tires or traction devices may be necessary. Ford offers tire cables as a Ford approved accessory and recommends use of these or SAE class “S” tire cables.
Tires, Wheels and Loading Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Tires, Wheels and Loading 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Tongue Load or Fifth Wheel King Pin Weight – refers to the amount of the weight that a trailer pushes down on a trailer hitch. Examples: For a 5,000 lb. (2,268 kg) conventional trailer, multiply 5,000 by 0.10 and 0.
Tires, Wheels and Loading 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You decide to go golfing.
Tires, Wheels and Loading Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’s Guide. Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken when driving a heavily loaded vehicle.
Tires, Wheels and Loading Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to the severe duty schedule in the scheduled maintenance guide.
Tires, Wheels and Loading 4x2 GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum Trailer weight GCWR-lb. (kg) range-lb. (kg) (0-Maximum) 4.0L SOHC Class 3.55 8500 (3856) 0–3500 (0–1588) II towing 4.6L* Class II 3.55 8500 (3856) 0–3500 (0–1588) towing 4.0L SOHC Class 3.73 10000 (4536) 0–5320 (0–2413) III/IV Towing 4.6L* Class III/IV 3.55 12000 (5443) 0–7230 (0–3279) Towing Notes: - For high altitude operation, reduce GCW by 2% per 1,000 ft. (300 meters) elevation.
Tires, Wheels and Loading AWD GCWR (Gross Combined Weight Rating)/Trailer Weight Engine Rear axle ratio Maximum Trailer weight GCWR-lb. (kg) range-lb. (kg) (0-Maximum) 4.0L SOHC Class 3.55 8500 (3856) 0–3500 (0–1588) II towing 4.6L* Class II 3.55 8500 (3856) 0–3500 (0–1588) towing 4.0L SOHC Class 3.73 10000 (4536) 0–5150 (0–2336) III/IV Towing 4.6L* Class III/IV 3.55 12000 (5443) 0–7060 (0–3202) Towing Notes: - For high altitude operation, reduce GCW by 2% per 1,000 ft. (300 meters) elevation.
Tires, Wheels and Loading Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Class III Trailer Hitch Safety Chain Loops can be used as recovery hooks. Do not attach safety chains to the bumper.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer, and don’t make full throttle starts. • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling.
Tires, Wheels and Loading • If you will be towing a trailer frequently in hot weather, hilly conditions, at GCW, or any combination of these factors, consider refilling your rear axle with synthetic gear lube if not already so equipped. Refer to the Maintenance and Specifications chapter for the lubricant specification.
Tires, Wheels and Loading RECREATIONAL TOWING (ALL WHEELS ON THE GROUND) Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. Rear Wheel Drive (RWD) 4x2 vehicles: This applies to all 4x2 trucks/sport utilities with rear wheel drive capability. • Place the transmission in N (Neutral).
Driving STARTING Positions of the ignition 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. This position also unlocks the steering wheel. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts.
Driving • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). • Turn the key to 3 (ON) without turning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn the key to 3 (ON) without turning the key to 4 (START). If there is difficulty in turning the key, rotate the steering wheel until the key turns freely.
Driving Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.
Driving Refer to Brake system warning light in the Instrument Cluster chapter for information on the brake system warning light. ! P BRAKE Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! P BRAKE Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. The parking brake is not recommended to stop a moving vehicle.
Driving Some drivers may notice a slight movement of the brake pedal when the AdvanceTrac威 with RSC performs a system self-check. During AdvanceTrac威 with RSC operation you may experience the following: • A rumble, grunting, or grinding noise after startup and when driving off • A slight deceleration of the vehicle • The AdvanceTrac威 with RSC indicator light will flash when the system is activated. • If your foot is on the brake pedal, you will feel a vibration in the pedal.
Driving Electronic Stability Control (ESC) The Electronic Stability Control (ESC) with RSC system may enhance your vehicle’s stability during adverse maneuvers. The AdvanceTrac威 with RSC system helps the driver maintain steering control. AdvanceTrac威 with RSC will attempt to correct the vehicle motion by applying brake force at individual tires and, if necessary, by reducing engine power. During Electronic Stability Control events the “sliding car” icon in the instrument cluster will flash momentarily.
Driving AdvanceTrac威 with RSC button and icon functionality The AdvanceTrac威 with RSC system automatically turns on each time the engine is started, even if it was turned off when the engine was last shut down. The “sliding car” icon which is located with the warning lights in the instrument cluster will illuminate during bulb check at initial start-up and then go off. This tells you that the system is normal and active.
Driving AdvanceTrac威 with RSC Features Engine Button “Sliding RSC ESC Traction functions car” icon Control Illuminated Default at during bulb Enabled Enabled Enabled start-up check Disabled Disabled Disabled Button Illuminated below 25 below 25 below 25 pressed solid mph (40 mph (40 mph (40 momentarily km/h) km/h) km/h) Button Flashes Disabled Disabled Disabled pressed and then below 25 below 25 below 25 held more illuminated mph (40 mph (40 mph (40 than five solid km/h) km/h) km/h) seconds Brake Traction
Driving • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, check for low power steering pump fluid level before seeking service by your authorized dealer. • Heavy or uneven steering efforts may be caused by low power steering pump fluid level. Check for low power steering pump fluid level before seeking service by your authorized dealer.
Driving Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Extra precautions such as slower speeds and increased stopping distance should be taken when driving a heavily loaded vehicle. AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed.
Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer. Driving with a 5–speed automatic transmission (if equipped) This vehicle is equipped with an Adaptive Transmission Control Strategy. This Adaptive Transmission Control Strategy offers the optimal transmission operation and shift quality.
Driving P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Press the gearshift release button on the front of the lever and move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Driving D (Drive) without Overdrive Overdrive can be deactivated by pressing the transmission control switch on the side of the gearshift lever. • This position allows for all forward gears (1-4) except overdrive. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears. Examples: city traffic, hilly terrain, heavy loads, trailer towing and when engine braking is required. • O/D OFF lamp is illuminated.
Driving Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. Driving with a 6–speed automatic transmission (if equipped) This vehicle is equipped with an Adaptive Transmission Control Strategy. This Adaptive Transmission Control Strategy offers the optimal transmission operation and shift quality. The transmission is equipped with a Transmission Control Module (TCM) located within the transmission assembly.
Driving P (Park) This position locks the transmission and prevents the rear wheels from turning. To put your vehicle in gear: • Depress the brake pedal • Start the engine • Press the gearshift lever release button (on the front of the lever) and shift into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Driving D (Drive) without Overdrive Overdrive can be deactivated by pressing the transmission control switch on the side of the shift lever. • This position allows for all forward gears (1-4) except overdrive. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears. Examples: city traffic, hilly terrain, heavy loads, trailer towing and when engine braking is required. • O/D OFF lamp is illuminated.
Driving • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Drive) only. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear. If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out by shifting between forward and reverse gears, stopping between shifts in a steady pattern.
Driving Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps. The RSS detects obstacles up to six feet (two meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.
Driving For the lubricant specification and refill capacity of the AWD transfer case refer to Maintenance and Specifications chapter. If your vehicle is equipped with AWD, a spare tire of a different size than the road tires should never be used. Such a tire could make the vehicle difficult to control as well as result in damage to driveline components.
Driving • AWD LOCKED will be displayed in the message center for four seconds and a warning chime will sound. This condition may clear without any action being taken by the driver. • the 4X4 indicator light in the instrument cluster will turn off when the AWD system cools down. Disabling AWD (vehicles equipped with AdvanceTrac姞 with RSC only) When a problem is detected in the AWD system: • the 4X4 indicator light in the instrument cluster will flash eight times every two minutes in the message center.
Driving The differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
Driving If your vehicle gets stuck If your vehicle gets stuck in mud or snow it may be rocked out by shifting between forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat.
Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns, excessive speed and abrupt maneuvers in these vehicles.
Driving Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited. When driving through water, determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly. If the ignition system gets wet, the vehicle may stall. Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Driving Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use.
Driving Driving on snow and ice AWD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. Avoid sudden braking as well.
Driving Failure to maintain your vehicle properly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety. Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage. DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment.
Roadside Emergencies HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Use it when your vehicle is disabled and is creating a safety hazard for other motorists.
Roadside Emergencies The fuel pump shut-off switch is located in the passenger’s foot well, by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the OFF position. 5.
Roadside Emergencies Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse rating 2A 3A 4A 5A 7.
Roadside Emergencies Passenger compartment fuse panel The fuse panel is located below the instrument panel on the driver’s side. To remove a fuse use the fuse puller tool provided on the fuse panel box.
Roadside Emergencies Fuse/Relay Location 6 Fuse Amp Rating 20A 7 8 9 15A 15A 2A 10 5A 11 12 5A 5A 13 15A 14 15 16 17 18 20A 10A 10A 10A 10A 19 20 — 10A 21 22 — 15A 23 15A Passenger Compartment Fuse Panel Description Liftglass release motor, Door unlock/lock Trailer stop/turn Ignition switch power, PATS 6R TCM/PCM (Ignition RUN/START), Fuel pump relay Front wiper RUN/ACC relay in PDB Radio start Rear wiper motor RUN/ACC, Trailer battery charge relay in PDB, Radio Heated mirror, Rear defrost
Roadside Emergencies Fuse/Relay Location 24 25 Fuse Amp Rating 10A 15A 26 15A 27 28 CB1 15A 10A 25A Passenger Compartment Fuse Panel Description Cluster, Theft LED Trailer park, Trailer electronic brake module License plate/rear park lamp, Front park lamps, Manual climate Tri-color stop lamps Manual/DEATC Windows The following relays are located on either side of the passenger compartment fuse panel. See your authorized dealer for service of these relays.
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies 1 2 3 4 5 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 55 6 11 7 12 8 13 9 14 56 10 15 52 53 54 51 16 17 18 45B 19 20 41 43 44 50B 46B 47 45A 42 48 49 50A 46A The high-current fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 6 7 Fuse Amp Rating 50A** 50A** 50A** 30A** 30A** 40A** 40A** 8 9 10 11 12 13 — — 30A** 30A** 30A** 30A** 254 2006 Mountaineer (mnt) Owners Guide (post-2002-fmt) USA (fus) Power Di
Roadside Emergencies Fuse/Relay Location 14 15 16 17 18 19 20 21 22 23 24 Fuse Amp Rating 30A** 40A** 40A** 40A** 30A** 30A** 30A** — 20A* 20A* — 10A* 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 20A* 20A* 20A* 20A* 20A* 25A* 15A* — 30A* 20A* 10A* — 30A* 15A* 15A* 15A* 41 15A* Power Distribution Box Description Memory seats (DSM) Non-memory seats Rear defrost, Heated mirrors Blower motor Trailer electronic brakes Auxiliary blower motor Running boards Not used Rear power point Subwoofer Not used Pow
Roadside Emergencies Fuse/Relay Location 42 Fuse Amp Rating 15A* 43 15A* 44 15A* 45A — 45B — 46A — 46B — 47 — 48 — 49 — 50A — 50B — 51 — 52 — 53 — 54 — 55 — 56 — * Mini Fuses ** Cartridge Fuses Power Distribution Box Description Redundant brake switch, EVMV, MAFS, HEGO, EVR, VCT1, VCT2, CMCV, CMS Coil on plug (4.6L engine only), Coil tower (4.
Roadside Emergencies Have a flat serviced by an authorized dealer in order to prevent damage to the TPMS sensor, refer to Changing tires with TPMS in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. The use of tire sealants may damage your tires. The use of tire sealants may also damage your Tire Pressure Monitoring System and should not be used.
Roadside Emergencies • Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar spare tire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • We
Roadside Emergencies When driving with the full-size dissimilar spare tire/wheel additional caution should be given to: • Towing a trailer • Driving vehicles equipped with a camper body • Driving vehicles with a load on the cargo rack Drive cautiously when using a full-size dissimilar spare tire/wheel and seek service as soon as possible. Stopping and securing the vehicle 1. If you get a flat tire while driving, do not apply the brake heavily; instead, gradually decrease your speed.
Roadside Emergencies The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Location Under the vehicle, just in front of the rear bumper. The spare tire winch drive nut is located at the rear center of the cargo area under a lid. Jack, lug nut wrench, jack handle, Behind the rear seat under the wheel chock carpeted floor lid in the cargo floor. The tools are located in a bag attached to the jack. Removing the jack and tools 1.
Roadside Emergencies Removing the spare tire Do not use an impact wrench on the winch drive nut. This will damage the spare tire winch. 1. Open the cover from the carpeting on cargo floor to expose the winch drive nut. 2. Insert the lug wrench on the winch drive nut. The wrench will stop moving and forward resistance to turning will be felt when properly engaged.
Roadside Emergencies 3. Turn the wrench counterclockwise until the tire is lowered to the ground and the cable has slack. When turning the wrench, make sure that it does not scuff the kick plate. 4. Slide the tire rearward, lift one side and remove the retainer from the spare tire. Changing the spare tire To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheel that is diagonally opposite (other end of the vehicle) to the tire being changed.
Roadside Emergencies 1. Use the tip of the lug wrench to remove the beauty cap by twisting the tip under the cap. On 5–passenger vehicles, the carpeted floor lid can be used as a kneeling pad. 2. Loosen each wheel lug nut by half a turn, but do not remove them until the wheel is raised off the ground. 3. Assemble the jack handle extension on the lug nut wrench by sliding the square end of the jack handle through the plastic grommet on the lug nut wrench and into the square hole on the other side.
Roadside Emergencies 4. Position the jack according to the illustrated guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board underbody mounts to lift the vehicle with the jack. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack.
Roadside Emergencies 8. Remove the jack and fully tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nut torque specification. 1 3 4 5 2 Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire. 1. Lay the tire on the ground with the valve stem facing up, toward the vehicle. 2.
Roadside Emergencies 2. Stow the wheel ornament (if removed) in a safe location in the vehicle (such as the glove box or jack stowage compartment) so it will not become damaged. Re-install the wheel ornament onto the wheel once the tire is repaired or replaced. 3. Stow the jack and tools in their respective locations, making sure they are fully secured so they do not rattle when you drive.
Roadside Emergencies Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + - + - 4. Make the final connection of the negative (-) cable to the ground stud located toward the front of the vehicle (forward of the battery) on the raidator support. Keep the negative (-) cable away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Ensure that the battery shield is properly installed before jump starting the vehicle.
Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery.
Roadside Emergencies + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING Note: Turn off the power running boards (if equipped) prior to preparing the vehicle for towing. Refer to Power deployable running boards in the Driver Controls chapter. If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt.
Roadside Emergencies On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground. On AWD vehicles, it is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment with all the wheels off the ground. If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Lincoln or Mercury vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you. In the United States: Ford Motor Company Customer Relationship Center P.O.
Customer Assistance In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. IN CALIFORNIA (U.S.
Customer Assistance achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program. The BBB AUTO LINE program consists of two parts – mediation and arbitration. Initially, the BBB will try to resolve your question or concern through mediation.
Customer Assistance The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment.
Customer Assistance If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a regional office or owner relations/customer relationship office. The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel.
Customer Assistance (Items in this catalog may be purchased by credit card, check or money order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your authorized dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. REPORTING SAFETY DEFECTS (U.S.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid Wax (ZC-53-A), which is available from your authorized dealer, or an equivalent quality product. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time.
Cleaning ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean.
Cleaning 4.0L SOHC V6 Engine 4.6L V8 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42).
Cleaning coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: • The windshield, rear windows and side windows may be cleaned with a non-abrasive cleaner such as Motorcraft Ultra-Clear Spray Glass Cleaner (ZC-23), available from your authorized dealer.
Cleaning INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side airbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14).
Cleaning FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work on a hot engine. • Make sure that nothing gets caught in moving parts.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Engine oil filler cap 2. Engine oil dipstick (out of view) 3. Brake fluid reservoir 4. Power distribution box 5. Battery 6. Power steering fluid reservoir 7. Radiator cap 8. Engine coolant reservoir 9. Air filter assembly 10.
Maintenance and Specifications 4.6L V8 engine 1. Air filter assembly 2. Engine oil filler cap 3. Engine oil dipstick 4. Brake fluid reservoir 5. Power distribution box 6. Battery 7. Power steering fluid reservoir 8. Radiator cap 9. Engine coolant reservoir 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to Lubricant specifications later in this chapter.
Maintenance and Specifications CHANGING THE WIPER BLADES 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at least once per year for optimum performance.
Maintenance and Specifications • 4.0L V6 engine • 4.6L V8 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the lower and upper holes, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the lower hole, add enough oil to raise the level within the lower and upper holes.
Maintenance and Specifications • 4.0L V6 engine • 4.6L V8 engine • Oil levels above the upper hole may cause engine damage. Some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications To avoid possible oil loss, DO NOT operate the vehicle with the engine oil level indicator and/or the engine oil filler cap removed. Engine Oil Recommendations 4.0L Engine Look for this certification trademark. Use SAE 5W-30 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API).
Maintenance and Specifications 4.6L Engine Look for this certification trademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to scheduled maintenance information for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and radio settings must be reset once the battery is reconnected. Additionally, the power running boards, if equipped, will default to the off mode and must be turned on again. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal.
Maintenance and Specifications • 4.0L V6 engine • 4.6L V8 engine • The engine coolant should be at the “FULL COLD” level as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Maintenance and Specifications Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.
Maintenance and Specifications For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level.
Maintenance and Specifications Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. What you should know about fail-safe cooling (4.
Maintenance and Specifications Oil overheat can be triggered in severe driving conditions, such as towing heavy loads over mountainous terrain in extreme hot temperatures. As oil temperature increases, engine and vehicle speed will be limited. The transmission will also shift differently. When the engine oil has cooled, the vehicle will perform normally. When fail-safe cooling mode is activated You have limited engine power when in the fail-safe mode, so drive the vehicle with caution.
Maintenance and Specifications If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury. Automotive fuels can cause serious injury or death if misused or mishandled. Gasoline may contain benzene, which is a cancer-causing agent.
Maintenance and Specifications splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes.
Maintenance and Specifications When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/4 of a turn to unscrew the cap. 3. Pull to remove the cap from the fuel filler pipe. 4. Reinstall the cap on the filler pipe and turn it clockwise until at least one click is heard. After refueling, if the “CHECK FUEL CAP” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed.
Maintenance and Specifications Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications • The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible.
Maintenance and Specifications • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4.
Maintenance and Specifications • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy.
Maintenance and Specifications • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact your authorized dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles. It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of MPG (L/100 km) expected on the vehicle under optimum conditions.
Maintenance and Specifications An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately. Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and Specifications Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test of the on-board diagnostics system. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may not pass the I/M test with the indicator on.
Maintenance and Specifications BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels below the “MAX” line that do not trigger the brake system warning lamp are within the normal operating range, there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of your brake system could be compromised, seek service from your authorized dealer immediately.
Maintenance and Specifications TRANSFER CASE FLUID (IF EQUIPPED) Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extended running board and the vehicle. A moving running board may cause injury. 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening.
Maintenance and Specifications AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter. To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1.
Maintenance and Specifications For PCV valve replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material and design specifications for your vehicle, such as a Motorcraft or equivalent replacement part. The customer warranty may be void for any damage to the emissions system if such a PCV valve is not used. 2 For spark plug replacement, see your authorized dealer.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid Fuel tank Ford Part Name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft SAE 5W-30 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-30 Super Premium Motor Oil (Canada) Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) N/A Power steering fluid Motorcraft MERCON 威 ATF All Transmission fluid 1 Motorcraft MERCON威 V ATF Transmission fluid 1 Mot
Maintenance and Specifications Fluid Transfer case Engine coolant Front axle lubricant (if equipped) Rear axle lubricant Windshield washer fluid 3 Ford Part Name Motorcraft MERCON 威 ATF Motorcraft Premium Gold Engine Coolant (yellow-colored) Application AWD Capacity 1.3 quarts (1.25L) 4.0L SOHC V6 12.2 quarts engine without (11.5L) auxiliary climate control 4.0L SOHC V6 13.9 quarts engine with (13.2L) auxiliary climate control 4.6L V8 engine 13.9 quarts without (13.2L) auxiliary climate control 4.
Maintenance and Specifications 2 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be checked by a qualified technician. 3 Add the coolant type originally equipped in your vehicle. Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only have the API Certification mark and meet the requirements of Ford specification WSS-M2C929-A (4.
Maintenance and Specifications Ford Part Name or equivalent Engine coolant Motorcraft Premium Gold Engine Coolant (yellow-colored) Motorcraft Cooling system Cooling System stop leak pellets Stop Leak Pellets Motorcraft SAE 5W-30 Premium Synthetic Blend Engine oil Motor Oil (US) Motorcraft SAE (4.0L) 5W-30 Super Premium Motor Oil (Canada) Motorcraft SAE 5W-20 Premium Synthetic Blend Engine oil Motor Oil (US) Motorcraft SAE (4.
Maintenance and Specifications Item Power steering fluid Rear axle Front axle (AWD) Transfer case (AWD) Ford Part Name or equivalent Motorcraft MERCON 威 Multi-Purpose ATF Motorcraft 75W-140 Synthetic Rear Axle Lubricant Motorcraft SAE 80W-90 Premium Rear Axle Lubricant Motorcraft MERCON威 Multi-Purpose ATF Ford Part Number Ford Specification XT-2-QDX MERCON威 XY-75W140–QL WSL-M2C192–A XY-80W90-QL WSP-M2C197-A XT-2-QDX MERCON威 Transfer case Front Output Slip Shaft (AWD) Premium XG-1-C Long-Lif
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 1 Spark plug gap is not adjustable 4.0L SOHC V6 engine 245 87 octane 1-4-2-5-3-6 EDIS 0.052–0.056 inch (1.32–1.42 mm) 9.7:1 VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Maximum height* (4) Wheelbase (5) Track width, front (5) Track width, rear Inches (mm) 193.5 (4916) 73.5 (1866) 72.8 (1849.1) 113.7 (2888.7) 60.9 (1547.5) 62 (1574.
Maintenance and Specifications 327 2006 Mountaineer (mnt) Owners Guide (post-2002-fmt) USA (fus)
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
Accessories MERCURY ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Mercury Accessories are available for your vehicle through your local Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle. In addition, each accessory is made from high quality materials and meets or exceeds Mercury’s rigorous engineering and safety specifications.
Accessories Peace of mind Mobile-Ease娂 hands-free communication system Remote start Vehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety Compliance Certification label).
Index A Accessory delay ..........................65 AdvanceTrac ..............................221 Air cleaner filter .......................319 Air conditioning ..........................43 Airbag supplemental restraint system ................151–152, 160, 162 and child safety seats ............153 description ..............152, 160, 162 disposal ....................................165 driver airbag ............154, 161, 163 indicator light .................160, 165 operation .................
Index washing ....................................281 waxing .....................................281 wheels ......................................282 wiper blades ............................284 Climate control (see Air conditioning or Heating) ............43 Clock adjust 6-CD in dash .............................32 AM/FM/CD .................................22 AM/FM/Tape/CD .......................27 Compass, electronic ....................83 calibration .................................
Index service points ..................290–291 starting after a collision .........247 Engine block heater .................219 Engine oil ..................................293 checking and adding ..............293 dipstick ....................................293 filter, specifications ........296, 319 recommendations ...................296 refill capacities ........................321 specifications ..................323, 326 Exhaust fumes ..........................219 F Fail safe cooling .................
Index Illuminated visor mirror .............60 Infant seats (see Safety seats) .....................170 Inspection/maintenance (I/M) testing ........................................316 Instrument panel cleaning ...................................285 cluster ........................................12 J Jack ....................................256, 260 positioning .......................256, 262 storage .....................256, 259–260 Jump-starting your vehicle ......266 K Keyless entry system .............
Index Passenger Occupant Classification Sensor .................137 Pedals (see Power adjustable foot pedals) .................................67 Power adjustable foot pedals .....67 Power deployable running boards ........................................103 Power distribution box (see Fuses) ...............................253 Power door locks ......................108 Power mirrors .............................66 Power point ...........................62–63 Power steering ..........................
Index Speed control ..............................67 Starting your vehicle ........217–218 jump starting ..........................266 Steering wheel controls ......................................70 tilting .........................................60 T Tilt steering wheel ......................60 Tire Pressure Monitoring System (TPMS) Roadside Emergencies ...........256 Tires, Wheels and Loading ....196 Warning Displays ........12, 85, 100 Tires ...........................182–183, 256 alignment ...........
