Table of Contents Introduction Instrument Cluster 4 10 Warning and control lights Gauges 10 14 Entertainment Systems 17 AM/FM stereo with CD AM/FM stereo cassette with CD Climate Controls Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 17 20 30 30 40 41 41 46 48 53 53 54 64 65 67 75 Locks and Security 90 K
Table of Contents Seating and Safety Restraints Seating Safety restraints Airbags Child restraints Tires, Wheels and Loading Tire Information Tire Inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving 108 108 133 147 161 179 179 181 193 199 205 210 211 Starting Brakes Transmission operation 211 214 219 Roadside Emergencies 227 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Lug Nut Tor
Table of Contents Maintenance and Specifications Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications 270 272 274 277 280 285 302 302 303 304 Accessories 310 Index 312 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered by your vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter.
Introduction To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check Fuel Cap Low Tire Pressure Warning MAX
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information.
Instrument Cluster Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Check engine warning light to come on, refer to Fuel filler cap in the Maintenance and Specification chapter.
Instrument Cluster Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Malfunction indicator: Illuminates when a powertrain fault has been detected. Contact your authorized dealer as soon as possible. Charging system: Illuminates when the battery is not charging properly. Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter.
Instrument Cluster not turn ON or begins to flash, have the system inspected by your authorized dealer. For more information on this system, refer to Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. Low fuel: Illuminates when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. Turns off when the speed control system is disengaged.
Instrument Cluster High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened.
Instrument Cluster Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot. Odometer: Registers the total miles (kilometers) of the vehicle.
Instrument Cluster Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade. The arrow near the fuel pump icon indicates which side of the vehicle the fuel filler door is located. Refer to Filling the tank in the Maintenance and Specifications chapter for more information.
Entertainment Systems AUDIO SYSTEMS AM/FM stereo/ single CD sound system (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press / / SEEK to set.
Entertainment Systems Treble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. / / SEEK . Use Fade: Press to adjust the audio between the front and rear speakers. / / SEEK . Use Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind / / SEEK to adjust. noise.
Entertainment Systems 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16.
Entertainment Systems AM/FM stereo with cassette/CD (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Seek:Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 4. Menu: Press to toggle through the following modes: Treble: Press to adjust the treble setting. Use / / SEEK . / / SEEK . Bass: Press to adjust the bass setting.
Entertainment Systems Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU to access and use / / SEEK to adjust. Setting the clock: Your vehicle is equipped with an in-dash clock. Refer to “Setting the clock” in the Driver Controls chapter for further information.
Entertainment Systems 9. Compress (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a CD track. 12. Rewind: Press to manually reverse in a CD track. 13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 14. Tape: Insert a tape facing to the right. 15.
Entertainment Systems 19. CD eject: Press to eject a CD. 20. CD slot: Insert a CD label side up. 21. Seek:Press to access the previous strong station or track. 22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. Premium In-Dash Six CD Sound System (if equipped) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings.
Entertainment Systems 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: / Treble: Press to adjust the treble setting. Use Bass: Press to adjust the bass setting. Use / / / SEEK SEEK . . Balance: Press to adjust the audio between the left and right speakers. / / SEEK . Use Fade: Press to adjust the audio between the front and rear speakers. / / SEEK .
Entertainment Systems 6. Text: In CD mode, press to display the track name, artist name and disc name (if available). 7. Shuffle: Press to play tracks in random order. 8. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 9. Repeat: Press to repeat the current CD track. 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12.
Entertainment Systems 17. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last. 18. LOAD: Press to load a CD. Press and hold to autoload up to six CDs. 19. CD eject: Press to eject a CD. Press and hold to auto eject all CDs present in the system. 20. CD slot: Insert a CD label side up. Auxiliary audio controls (if equipped) Your vehicle may be equipped with auxiliary audio controls.
Entertainment Systems mode). In this mode, all speakers will play audio from the same media source for all passengers to hear. If there is a discrepancy between the rear seat controls and the front audio controls (such as both trying to listen to the same playing media), the front audio system will receive the desired selection. To activate Dual Play mode (rear seat passengers listen to a different playing media than the front seat passengers): • Press the speaker/headphone control.
Entertainment Systems GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM: 530, 540 – 1700, 1710 kHz FM: 87.7, 87.9 – 107.7, 107.9 MHz Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from a station, the weaker the signal and the weaker the reception.
Entertainment Systems Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • For vehicles equipped with a six disc CD changer, don’t insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players.
Climate Controls DUAL ZONE MANUAL HEATING AND AIR CONDITIONING SYSTEM WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior air is more economical and efficient.
Climate Controls will be warmer or cooler than the driver airflow temperature setting when more than one rear temperature light ( REAR ) is illuminated. 5. R Rear defroster: Press to activate/deactivate rear window defroster. Refer to Rear window defroster later in this chapter for more information. 6. Recirculated air: Press to activate/deactivate air recirculation in cabin.
Climate Controls In the and modes: • Move the temperature control selector to the coldest setting. • Select A/C and recirculated air colder airflow. . Use with A/C to provide • Set the fan to the highest speed initially, then adjust to maintain passenger comfort. In extremely cold temperatures, to maximize overall heater performance it is suggested to not operate the auxiliary system (if so equipped) until the engine temperature gauge crosses into the normal operating range.
Climate Controls DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls engaged manually in any airflow selection except may turn off automatically in all airflow selections. . Recirculated air 7. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO, , and . : Distributes air through the windshield defroster vents and floor 8. vents. 9. : Distributes air through the floor vents. : Distributes air through the instrument panel vents and the floor 10. vents.
Climate Controls Dual zone automatic temperature control with heated seats and rear passenger compartment climate control (if equipped) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls 7. :Distributes air through the windshield defroster vents and the floor vents. 8. : Distributes air through the floor vents. 9. : Distributes air through the instrument panel vents and the floor vents. 10. : Distributes air through the instrument panel vents. 11. Manual override controls: Allows you to change the system operation. To return to full automatic control, press AUTO. 12. Driver heated seat control: Press once to activate the high heat setting (2 indicator lights).
Climate Controls 19. REAR: Press to enable the control located in the rear seat. Press again to turn the auxiliary system off. Dual automatic temperature control with heated and cooled seats and rear passenger compartment climate control (if equipped) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2.
Climate Controls 6. Passenger heated seat control: Press once to activate the high heat setting (2 indicator lights). Press again to activate the low heat setting (1 indicator light). Press again to deactivate the passenger heated seat. 7. Passenger cooled seat control: Press once to activate the high cool setting (2 indicator lights). Press again to activate the low cool setting (1 indicator light). Press again to deactivate the passenger cooled seat. 8.
Climate Controls 16. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO, , and . 17. REAR: Press to enable the control located in the rear seat. Press again to turn the auxiliary system off. 18. Recirculated air: Press to activate/deactivate air recirculation in the vehicle cabin.
Climate Controls 3. Adjust the temperature control to maintain comfort. 4. Set the fan to the highest speed. 5. Direct the outer instrument panel vents towards the side windows. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: Turn to select the desired fan speed. 2.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. P Turns the headlamps on. PULL Note: Some vehicles may be equipped with a headlamps on with wipers feature. In order for this feature to work: • the ignition must be in run and the front wipers must be on greater than 10 seconds except during a mist wipe or while the wipers are on to clear washer fluid during a wash condition.
Lights Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a fixed period of time after the ignition switch is turned to OFF. • To turn autolamps on, rotate the . control counterclockwise to • To turn autolamps off, rotate the control clockwise to .
Lights Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Rotate the thumbwheel from left to right to brighten the instrument panel. • Rotate the thumbwheel from right to left to dim the instrument panel. Your vehicle also contains a feature called “sleeping baby mode” — in which the dome lamps will remain off and only the lower lamps will illuminate.
Lights • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 0.5 mm circle on the headlamp lens. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. 4.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS The interior lights illuminate when: • any door is opened (and the operation switch is in the middle position). • the instrument panel dimmer switch is moved to the passenger side position (right position). • any of the remote entry controls are pressed and the ignition is OFF (and the operation switch is in the middle position).
Lights Second row & third row dome and map lamps (if equipped) The second row dome and map lamps are located overhead, above the second row passenger seats. The dome lamp will stay on if the panel dimmer control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the driver’s side position, the lamp will not come on at all. The dome lamp will illuminate whenever a front door is opened.
Lights Cargo lamp The cargo lamp will stay on if the control is moved to the driver side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the passenger’s side position, the lamp will not come on at all. With the ignition key in the ACCESSORY or ON position, the rear cargo lamp can be turned ON or OFF by sliding the control. BULB REPLACEMENT Headlamp Condensation The headlamps are vented to equalize pressure.
Lights Function Trade Number Backup lamps 3156K Dome lamp (first row) 10W sofitte Cargo lamp 10W sofitte Map lamps (second row) H6W Dome lamp (third row) 10W sofitte Map lamps (overhead console) 906 Stepwell lamp T-562 Front seat footwell 194 Front door mounted courtesy lamp 168 Visor vanity lamp - Slide on Rail system (SOR) 37 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer.
Lights Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order. Replacing front parking/turn/sidemarker signal bulbs 1. Make sure the headlamp switch is in the OFF position and open the hood. 2.
Lights Replacing tail lamp/backup/turn lamp bulbs 1. Make sure the headlamp switch is in the OFF position and open the liftgate to expose the tail lamp assembly, then remove the retaining screws for the lamp assembly. 2. Carefully remove the lamp assembly. 3. Rotate bulb socket counterclockwise and remove from lamp assembly. 4. Pull bulb straight out of socket and push in new bulb. Install the new bulb(s) in reverse order.
Lights Replacing foglamp bulbs 1. Make sure the foglamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning counterclockwise. If a plastic tie strap restricts the rotation of the bulb socket and connector, cut the strap. Replacement of the strap is not necessary. 3. Disconnect the electrical connector. Install the new bulb in reverse order.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls TILT STEERING WHEEL To adjust the steering wheel: 1. Pull and hold the steering wheel release control toward you. 2. Move the steering wheel up or down until you find the desired location. 3. Release the steering wheel release control. This will lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp.
Driver Controls Conversation mirror The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror. Electronic compass/temperature display (if equipped) The overhead console may have an electronic compass and outside air temperature display. The compass heading and outside air temperature are displayed together - side by side. The display, as a whole, can be turned on or off by pressing the momentary push-button on the overhead console.
Driver Controls Zone variation mode 1. Determine which magnetic zone you are in by referring to the zone map. 2. Turn the ignition to the ON position. 3 2 1 15 4 14 13 5 12 6 7 8 9 1011 3. Press and hold the momentary push-button for approximately 4 seconds, until VAR is displayed, then release it. (Pressing the momentary push-button for 8 seconds de-calibrates the compass—see Compass Calibration Mode). 4. Press the button to increment the VAR number to the desired VAR number.
Driver Controls Note: Look for a parking lot away from buildings, light posts, manhole covers, sewer and drainage grates and other metallic objects. Some magnetic objects may be hidden underground. Look for signs of underground utilities, water mains or other industrial structures. The parking lot should be level and have a smooth surface. Blacktop is preferred over cement as a cement surface often contains iron reinforcing bars or metallic mesh that could interfere with the calibration process.
Driver Controls Manual door operation when vehicle is stopped or parked on a downhill grade In some cases it may be necessary to have someone hold the door while rear seat passengers are entering or exiting the vehicle. The hold open mechanism will restrain the door open when the vehicle is parked on moderate downhill grades.
Driver Controls The Power Door Lockout Control is located in the overhead console. With the control in the OFF position, power operation is disabled from both PSD handles and from both second row passenger switches. The overhead console switch and remote entry transmitter will operate the power doors regardless of the position of the lockout switch.
Driver Controls To power close the PSD with the inside or outside release handle: • Manually pull the door about 6 inches in the desired direction of travel. The power door assist will take over and complete the open or close operation. Pressing any of the switches, overhead console, second row passenger, or remote entry transmitter while the door is moving will cause the door to either reverse direction or stop depending on the position and direction of movement of the door.
Driver Controls Resetting the PSD The power sliding door may operate incorrectly or not at all because of the following conditions: • a low voltage or dead battery • the door is left opened for more than 6 hours • the battery is disconnected • the PSD Passenger compartment fuse panel fuse (fuse #11) is removed or blown. Refer to Fuses and relays in the Roadside Emergencies chapter.
Driver Controls To open the sliding door when the child safety lock is on: • Unlock the sliding door and open the door from the outside. • Press the right or left hand control on the overhead console or the remote to open the door. • The second row passenger switch will still be functional to open the door. To prevent the second row passenger from operating the PSD, turn the Power Door Lockout control to the OFF position.
Driver Controls Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. To prevent the battery from being discharged, do not use the power point longer than necessary when the engine is not running. Always keep the power point caps closed when not being used. There are up to three auxiliary power points in the following locations: • Located on the instrument panel.
Driver Controls Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Improper use of the lighter can cause damage not covered by your warranty.
Driver Controls Power vent windows Do not leave children unattended in the vehicle and do not let children play with the power vent windows. They may seriously injure themselves. When closing the power vent windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. The power vent windows are operated by a single switch located on the instrument panel.
Driver Controls POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
Driver Controls Fold-away mirrors Carefully pull the outside mirrors inwards when driving through a narrow space, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.8 inches (73 mm) of maximum travel.
Driver Controls Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. light on the 5. The indicator instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill.
Driver Controls Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h). • Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.
Driver Controls Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal. This will not erase your vehicle’s previously set speed. • Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press MEDIA to select AM, FM1, FM2, TAPE or CD (if equipped).
Driver Controls CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a utility compartment. POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) To install floor mats that have a retention post: Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.
Driver Controls Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal. 1.
Driver Controls Note: If the indicator light blinks rapidly for two seconds and then turns to a continuous red, proceed with Steps 6 through 8 to complete programming of a rolling code equipped device. 6. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 7. Press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.
Driver Controls Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.
Driver Controls MESSAGE CENTER With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by an indicator chime.
Driver Controls DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected. Average Fuel Economy (AFE) Select this function from the INFO menu to display your average fuel economy in 100 miles/gallon or liters/100 km.
Driver Controls Setup menu Press this control for the following displays: • Language • Units (English/Metric) • System Check INFO SETUP RESET Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control for 2 seconds to set the language choice. Units (English/Metric) 1.
Driver Controls System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate a warning message for three seconds when there is a malfunction. Pressing the RESET control cycles the message center through each of the systems being monitored and will display the following only when there is a malfunction. 1. Oil life in XX% 2. Charging system 3. Washer fluid level 4.
Driver Controls This acts as a reminder that these warning conditions still exist within the vehicle.
Driver Controls CHECK BRAKE SYSTEM. Displayed when the braking system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK BRAKE LAMPS. Displayed when the brake lamps are activated and at least one is burned out. Check the lamps as soon as possible and have the burned out lamp replaced. The center high-mount brakelamp is not monitored. CHECK LEFT OR RIGHT HEADLAMPS.
Driver Controls An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press the SETUP control to access the System Check function. 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4.
Driver Controls 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”. 5. Press RESET until you find your personalized OIL LIFE XX%. 6. With your personalized OIL LIFE XX% displayed, press SETUP to continue the system check.
Driver Controls LIFTGATE Unlock the liftgate (but not release it) with the power door lock system and remote entry transmitter. To open the liftgate, pull the liftgate handle rearward. • Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is opened, the liftgate could be damaged against a low ceiling. • Do not leave the liftgate open while driving.
Driver Controls Keep the keys out of the reach of children. Do not allow children to play on or near an open or moving power liftgate. Exercise care, when power opening or closing the PLG in a garage or other enclosed area with a low ceiling or close to a wall/garage door. The PLG could be damaged from the contact. Do not attempt to manually force the PLG to travel faster than the power system will permit. When power operating the PLG at temperatures below 32° F (0° C), the PLG may stop about 5 inches (12.
Driver Controls To power open the PLG with outside release handle: 1. Ensure that the Power Door Lockout Control in the overhead console is ON. 2. Ensure that the PLG is unlocked, using the remote entry transmitter or power door unlock. Refer to Remote Entry System in the Locks and security chapter. 3. Pull up on the liftgate handle to engage the power assist feature. Release the handle as soon as the PLG begins to power open.
Driver Controls PLG encounters an obstacle while opening, the PLG will stop when it encounters a solid obstacle. Close the liftgate manually and remove the obstruction. Normal operation can then be resumed. Resetting the PLG: The power liftgate may not operate properly if any of the following conditions occur: • a low voltage or dead battery • disconnected battery • the liftgate has been left open or unlatched for more than six (6) hours If any of these conditions occur, the PLG must be reset.
Driver Controls CARGO AREA FEATURES Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lbs. (22 kg) in the net. The cargo net is not designed to restrain objects during a collision or heavy braking. Utility hooks The utility hooks can be used to hang small items. Do not hang more than 20 lb. (12 kg) on each of the hooks. The hooks are not designed to restrain objects during a collision.
Driver Controls To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the desired location. 3. Tighten the thumbwheel at both ends of the cross-bar. To remove the cross-bar assembly (if equipped): 1. Remove rear support covers from the rear rails. Place a small object into the pin holes and slide the cover out towards the rear of the vehicle. 2.
Driver Controls To reinstall the cross-bar assembly (if equipped): 1. Slide the cross-bar into the rail track with the arrow facing towards the front of the vehicle. Slide the bar forward passed the retaining clip. 2. Firmly tighten the thumbscrews at both ends of the cross-bar. 3. Install both support covers by sliding the covers back into the channel and pushing gently into place. Note: When the cross-bars are not in use, remove or move the cross-bars to the back of the roof rack for optimum wind noise.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information. POWER DOOR LOCKS Press the top portion of the control to unlock all doors and the bottom portion to lock all doors.
Locks and Security Unlocking the liftgate during a battery failure In the event of a vehicle power failure affecting the liftgate latch, the liftgate can be unlocked manually. 1. Locate the liftgate trim access panel in the center of the liftgate. 2. Using your key, a small screwdriver or knife, pry off the access panel. 3.
Locks and Security CHILDPROOF DOOR LOCKS • When these locks are set, the sliding doors cannot be opened with the inside handle. • The sliding doors can be opened from the outside when the doors are unlocked. The childproof lock controls are located on front edge of each sliding door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors. • Move lock control up to engage the childproof lock feature.
Locks and Security • 3–button remote • 5–button remote • 6–button remote The remote entry system allows you to: • lock or unlock all vehicle doors and liftgate without a key. • unlock/open a driver’s side power sliding door and/or passenger side power sliding door (if equipped). • unlock/open the power liftgate (PLG) (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system (if equipped).
Locks and Security If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate and the anti-theft system (if equipped) will disarm. and release again within three seconds to unlock all doors 2. Press and the liftgate.
Locks and Security Opening power liftgate (PLG) (if equipped) Press the control twice within three seconds to power open the power liftgate. The interior lamps will illuminate. Make sure all persons are clear of the power liftgate area before using the power liftgate controls to open or close the liftgate. Press the control another two times within three seconds to close the power liftgate and turn off the interior lights.
Locks and Security If any of the doors, the liftgate or the hood (if equipped with perimeter alarm) are not properly closed, the horn will make two quick chirps and the parklamps will not flash. Sounding a panic alarm Press to activate the alarm. The alarm will cycle the horn, the turn signals will flash, and the interior lamps will illuminate. Press again or turn the ignition to the 4 (ON) or the 1 (ACCESSORY) position to deactivate.
Locks and Security 5. Snap the two halves back together. Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.
Locks and Security 9. Turn the ignition to the 3 (OFF) position after you have finished programming all of the remote entry transmitters. 10. The doors will lock, then unlock, to confirm that the programming mode has been exited. Illuminated entry The interior lamps illuminate when the key in the driver’s door lock cylinder (if equipped with perimeter alarm), the keyless entry system or the remote entry transmitter is used to unlock the door(s), power sliding doors (if equipped) or liftgate.
Locks and Security • Head lamps • Park lamps • Tail lamps The system will automatically turn off if: • the vehicle is locked using the remote entry system, the keyless entry keypad, or • the ignition is turned to the 4 (ON) position, or • after 25 seconds of illumination. Deactivating/activating perimeter lamps You may enable/disable this feature by having your vehicle serviced by your authorized dealer.
Locks and Security Press to automatically move the driver seat, side view mirrors and adjustable pedals to the desired memory position. Associating the remote transmitter with the memory feature To activate this feature: 1. Position the driver’s seat, side view mirrors and adjustable pedals to the positions you desire. 2. Press the SET control on the door next to the window inside from the mirror. 3.
Locks and Security The keypad can be operated with the factory set 5–digit entry code; this code is located: • on the owner’s wallet card in the glove box, • marked on the passenger compartment fuse panel (located below and to the left of the steering, near the brake pedal), • and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Locks and Security Tips for setting codes: • The factory set code cannot be erased or changed. • The factory code will work even after you have set your own personal codes. • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds of entering the factory code, press and release the 1 • 2 control.
Locks and Security • the ignition is in the 4 (ON) position, • the brake is pressed before reaching 5 mph (8 km/h), and • then the vehicle increases to more than 5 mph (8 km/h). Relock The autolock feature repeats when: • an “autolock” occurrence has already taken place, • the brake is depressed while vehicle speed is less than 5 mph (8 km/h), • all vehicle doors become closed again, and • then the vehicle increases to more than 5 mph (8 km/h).
Locks and Security 1. Turn the ignition key to the 4 (ON) position. 2. Press the power door unlock control three times. 3. Turn the ignition key from the 4 (ON) position to the 3 (OFF) position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the 4 (ON) position. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7.
Locks and Security The following items may prevent the vehicle from starting: • Large metallic objects. • Electronic devices on the key chain that can be used to purchase gasoline or similar items. • A second key on the same key ring as the coded key. If any of these items are present, you need to prevent these objects from touching the coded key while starting the engine.
Locks and Security 1. Insert the first previously programmed coded key into the ignition and turn the ignition from the 3 (OFF) position to the 4 (ON) position [maintain ignition in 4 (ON) for at least three seconds, but no more than ten seconds]. 2. Turn ignition from the 4 (ON) position back to the 3 (OFF) position in order to remove the first coded key from the ignition. 3 4 5 2 1 3.
Locks and Security Arming the system When armed, this system will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the turn signal lamps and side repeaters and honk the horn. The system is ready to arm whenever the key is removed from the ignition. Any of the following actions will prearm the alarm system: • Locking the vehicle using the remote entry transmitter. • Locking the vehicle using the keyless entry keypad.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback.
Seating and Safety Restraints Push control to lower head restraint. Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward. Pull lever up to adjust seatback.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and Safety Restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on the climate control system panel once to activate high heat. • Push twice to activate low heat. • Push a third time to deactivate. The indicator light on the control will illuminate when activated.
Seating and Safety Restraints • Push again to operate the heated/cooled system at a lower level. • Push again to deactivate. The climate controlled seat system includes an air filter that has to be replaced periodically. Refer to the scheduled maintenance information for more information. Do not run heated/cooled system with the filter removed.
Seating and Safety Restraints • To program position two, repeat the previous procedure using control 2. A position can only be recalled when the transmission gearshift is in Park. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remote entry transmitter UNLOCK control if the transmitter is programmed to a memory position or when you enter a valid personal entry code that is programmed to a memory position.
Seating and Safety Restraints Seat mounted cup holders (if equipped) Deploy by pressing the button on top of the cupholder. The cupholder is designed to detach from the seat when subjected to heavy load. The cupholder can be reinstalled by returning to the closed position. Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Seating and Safety Restraints Adjusting 2nd row seats (if equipped) Lift control to adjust seat forward or backward. • 2nd row bucket seat (if equipped) • 2nd row bench seat (if equipped) Note: This seat can be moved forward to keep a child in a LATCH child restraint attached to the LATCH anchors at the center of the bench seat close to the front seat occupants or to increase cargo room without removing the seat.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Accessing the third row seat with a second row bucket seat Ensure head restraint is in the full down position and seat is adjusted to full rear position (if equipped). Note: Place the front row seat in a forward position to allow the 2nd row to be fully upright. Lift the handle located on the rear lower corner of the seat.
Seating and Safety Restraints Continuing to lift the handle will tumble the seat forward, allowing easier access to the third row seat. After entering the 3rd row seat, return the seat from the tumbled position and latch it to the floor. Operate recline control to return the seatback to the upright position. Note: • Ensure that the seat and seatback is latched securely in position. • Keep floor area free of objects that would prevent proper seat engagement.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop.
Seating and Safety Restraints Second row bench seat To exit the third row, activate the easy entry system by pulling on the strap on the rear of the seat. This will cause the seatback to flip forward and the seat track latches to open. Push the seat forward to allow easier exit from the third row. After exiting the third row, push rearward on the cushion of the seat to return the seat to its original position. Push the seatback rearward until it latches.
Seating and Safety Restraints 3. Place seat in tumbled position. (See Accessing 3rd row seat) 4. From inside the vehicle, pull up on front floor release handle. 5. Rotate the seat rearward at a 30 to 45 degree angle.
Seating and Safety Restraints 6. With the assist handle, pull the seat rearward. 7. Remove the seat from vehicle. Second row bench seat 1. Detach the lap/shoulder belts from both sides of the seat by inserting a seat belt tongue or key into the buckle release slot, pushing upward as shown, and pulling out the mini-tongue on the end of the seat belt.
Seating and Safety Restraints 2. Find the clips attached near the ends of the lap/shoulder belts. 3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
Seating and Safety Restraints 4. Position seatback in full down position. 5. From behind seat pull straight back on the release handles located on each side of the seat, releasing the rear floor latches. 6. Lift up the seat by the release handles to clear the floor latches and then pull the seat rearward until the front hooks have come out of the floor tubs. 7. Remove the seat.
Seating and Safety Restraints 2. Install seat onto rear pin of front tub at a 30 to 45 degree angle. 3. Rotate the seat forward until it latches onto the front pin. 4. Rotate seat rearward until the back of the seat latches onto the floor.
Seating and Safety Restraints 5. Operate recline lever and push the seat back upright. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
Seating and Safety Restraints 3. Lower back of seat onto the rear tubs until both release controls latch into place. Be sure that the seat is locked in place both front and back. Do not place the seat front hooks on the front most pin of the front tub. Doing so will not allow the seat to fully install in vehicle. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop. Stowing the third row seat 1.
Seating and Safety Restraints 2. If you plan to carry very large objects or items that might damage the center lap/shoulder belt, detach the belt from the seat. Use a key or seat belt tongue to release the buckle. 3. Store the tongue of the sliding latchplate in the belt pocket.
Seating and Safety Restraints 4. Store the belt in the housing found on the ceiling by inserting the smaller tongue in the slot provided. Note: The seat can be stowed with the safety belt connected if desired. Store the tongue of the sliding latchplate in the belt pocket to avoid potential damage to the seat. 5. Push the head restraint release buttons and move the head restraints fully down. Remove all objects from the seat and stowage tub. 6.
Seating and Safety Restraints Important: If you don’t let go of the number 1 strap before the seat back folds completely, the seat may not stow flat in the tub. Refer to the label attached to the rear of the vehicle seat. 7. Release the cushion latches by pulling the number 2 strap.
Seating and Safety Restraints 8. Pull the number 3 strap on the seat back to tumble seat all the way in to the tub in the floor. Do not use the seat anchors as cargo tie downs. Unstowing the third row seat Ensure seat latching area is free of objects. 1. Lift the seat out of the tub in the floor by pulling up on the exposed strap or handle. Once seat is at a vertical position, push the seat over, letting it fall onto the latches.
Seating and Safety Restraints 2. To return the seat back to the seating position, pull the number 1 strap, then while holding the number 1 strap, pull the number 3 strap to raise the seat back. 3. Release the number 1 strap to allow the seat to lock, then release the number 3 strap. 4. Pull up on the head restraints to adjust them. 5.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Tailgate function The 3rd row seat is equipped with a tailgate function to be utilized when the vehicle is parked and engine turned off. This rearward-facing position allows the customer to open the liftgate and sit facing out of the vehicle rearward. This is not a position suitable for driving.
Seating and Safety Restraints 3. To return the seat, ensure seat latching area is free of objects. Then, raise the seat off the liftgate scuff plate and push at the top of the seat back to rotate the seat back onto the latches. Pull up on the head restraints to raise them. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop.
Seating and Safety Restraints conditions. A collection of crash and occupant sensors provides information to the Restraints Control Module (RCM). During a crash, the RCM activates the safety belt pretensioners and/or either one or both stages of the dual-stage airbag supplemental restraints based on crash severity and occupant conditions. The fact that the pretensioners or airbags did not activate for both front seat occupants in a collision does not mean that something is wrong with the system.
Seating and Safety Restraints occupants, this occurs when the occupant is not properly restrained by seat belts or child safety seats and they move forward during pre-crash braking. The most effective way to reduce the risk of unnecessary injuries is to make sure all occupants are properly restrained. Accident statistics suggest that children are much safer when properly restrained in the rear seating positions than in the front. Air bags can kill or injure a child in a child seat.
Seating and Safety Restraints Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum. This helps reduce the risk of force-related injuries to the occupant’s chest by limiting the load on the occupant. Refer to Energy management feature section in this chapter.
Seating and Safety Restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle.
Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. To unfasten, push the release button and remove the tongue from the buckle. All restraints in the vehicle are combination lap and shoulder belts.
Seating and Safety Restraints All safety restraints in the vehicle are combination lap and shoulder belts. All of the passenger combination lap and shoulder belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and Safety Restraints • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...
Seating and Safety Restraints Reasons given... “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an airbag” “I’d rather be thrown clear” Consider... We design our safety belts to enhance comfort. If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident.
Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the BeltMinder娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the BeltMinder娂 feature please follow the directions stated below. One time disable If at any time the driver/front passenger quickly buckles then unbuckles the safety belt for that seating position, the BeltMinder娂 is disabled for the current ignition cycle.
Seating and Safety Restraints • Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.) • After Step 3, the restraint system warning light (airbag light) will be turned on for three seconds. 4.
Seating and Safety Restraints assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
Seating and Safety Restraints The airbag supplemental restraint system (SRS) is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the airbags are intended as a supplement to the safety belts.
Seating and Safety Restraints To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the airbag module. Placing objects on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Seating and Safety Restraints How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger airbag modules (which include the inflators and airbags). • side airbags (if equipped). Refer to Side airbag system later in this chapter.
Seating and Safety Restraints • the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period of time, • a child or a small person occupies the front passenger seat.
Seating and Safety Restraints • When the front passenger sensing system enables the front passenger frontal airbag (may inflate), the indicator will be unlit and stay unlit. If a person of adult size is sitting in the front passenger’s seat, but the ⬙passenger airbag off⬙ or ⬙pass airbag off⬙ indicator lamp is lit, it is possible that the person isn’t sitting properly in the seat. If this happens: • Turn the vehicle off and ask the person to place the seatback in the full upright position.
Seating and Safety Restraints The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙pass airbag off⬙ lamp may or may not be illuminated according to the table below. Objects Pass Airbag Off Indicator Light Unlit Small (i.e. 3 ring binder, small purse, bottled water) Medium (i.e.
Seating and Safety Restraints To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check Passenger Airbag Disable Indicator for proper airbag Status. Failure to follow these instructions may interfere with the front passenger seat sensing system.
Seating and Safety Restraints If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide. Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system.
Seating and Safety Restraints Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided.
Seating and Safety Restraints The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateral deceleration sufficient to cause the sensors to close an electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system.
Seating and Safety Restraints Do not lean your head on the door. The Safety Canopy娂 could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the Safety Canopy娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy娂. See your authorized dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy娂 system is provided.
Seating and Safety Restraints • An inflatable nylon curtain with a gas generator concealed behind the headliner and above the doors (one on each side of vehicle). • A headliner designed to flex open above the side doors to allow Safety Canopy娂 deployment. • The same readiness airbag light, electronic control and diagnostic unit as used for the front airbags. • Two crash sensors mounted under the front seats (one on each side).
Seating and Safety Restraints If the Safety Canopy娂 system has deployed, the Safety Canopy娂 will not function again unless replaced. The Safety Canopy娂 system (including the A, B, C, and D pillar trim) must be inspected and serviced by an authorized dealer. If the Safety Canopy娂 is not replaced, the unrepaired area will increase the risk of injury in a collision.
Seating and Safety Restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that children use approved booster seats until they are eight years old.
Seating and Safety Restraints To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably. Booster seats also make the shoulder belt fit better and more comfortably for growing children.
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder belt should cross the chest, resting snugly on the center of the shoulder.
Seating and Safety Restraints Child booster seats Children outgrow a typical convertible or toddler seat when they weigh 40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulder belt will provide some protection, these children are still too small for lap/shoulder belts to fit properly, which could increase the risk of serious injury.
Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat.
Seating and Safety Restraints Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder. The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably close to the neck and a shoulder belt that could slip off the shoulder.
Seating and Safety Restraints The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’s head hitting a hard surface in a collision. For this reason, you should never use a booster seat with a lap belt only. It is best to use a booster seat with lap/shoulder belts in the back seat- the safest place for children to ride. Move a child to a different seating location if the shoulder belt does not stay positioned on the shoulder during use.
Seating and Safety Restraints When installing a child safety seat: • Review and follow the information presented in the Airbag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and Safety Restraints Installing child safety seats with combination lap and shoulder belts Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Children 12 and under should be properly restrained in the rear seat whenever possible. 1. Position the child safety seat in a seat with a combination lap and shoulder belt.
Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and Safety Restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward.
Seating and Safety Restraints The tether anchors in your vehicle are in the positions shown: The front passenger seat with power adjustment does not have a tether anchor. The two tether anchors on the back of the second row bench seat can be used either for child safety seats at the two seating positions, or either anchor can be used for a single LATCH child seat installed at the center of the bench seat. Front passenger seating position (manual adjusting seats only) 1.
Seating and Safety Restraints 2. Route the child safety seat tether strap over the back of the seat. If the head restraint is adjustable, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, raise the head restraint to let the child seat fit further rearward. 3. Grasp the tether strap and position it to the seat frame. 4. Rotate the tether hook, and clip the tether strap to the seat frame.
Seating and Safety Restraints If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. 5. Rotate the tether strap clip. 6. Install the child safety seat tightly using the LATCH anchors or safety belts. Follow the instructions in this chapter. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions.
Seating and Safety Restraints Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket • 2nd row bench • 3rd row bench For additional important safety information on the proper use of safety belts, child seats and infant seats, please read the entire Seating and safety restraints chapter in this owner’s guide.
Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol. If your vehicle has a second row bench seat, one child seat can be placed in each outboard seating position, or one LATCH child seat can be placed in the center of the seat only. Please note that the center-only position does not have a separate tether anchor. Either of the outboard tether anchors may be used for the center position.
Seating and Safety Restraints Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Attach LATCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat.
Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tires, Wheels and Loading • • • • • • • • • Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. kPa: Kilopascal, a metric unit of air pressure. PSI: Pounds per square inch, a standard unit of air pressure. Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.6 km).
Tires, Wheels and Loading Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙blowout⬙, with unexpected loss of vehicle control and increased risk of injury. Under-inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may result in unnecessary tire stress, irregular wear, loss of vehicle control and accidents.
Tires, Wheels and Loading when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. Never “bleed” or reduce air pressure when tires are hot. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge. 3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pushing on the metal stem in the center of the valve.
Tires, Wheels and Loading Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm). When the tire tread wears down to the same height as these “wear bars”, the tire is worn out and must be replaced.
Tires, Wheels and Loading If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of the 35 mph (55 km/h) point indicated on the speedometer. Highway hazards No matter how carefully you drive there’s always the possibility that you may eventually have a flat tire on the highway. Drive slowly to the closest safe area out of traffic.
Tires, Wheels and Loading • Front Wheel Drive (FWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
Tires, Wheels and Loading Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the sensor. It is recommended that you always have your tires serviced by an authorized dealer.
Tires, Wheels and Loading wheel/tire needs to be repaired and put back on your vehicle. During this time, the low tire warning light can periodically return or stay on, depending on the state of the damaged road wheel/tire. This will include messages from the message center (if equipped). To restore the full functionality of the Tire Pressure Monitoring System, have the damaged road wheel/tire repaired and remounted on your vehicle.
Tires, Wheels and Loading Low Tire Pressure Possible cause Customer Action Required Warning Light Solid Warning Light Tire(s) 1. Check your tire pressure to under-inflated ensure they are properly inflated; refer to Inflating your tires in this chapter. Ford Motor Company recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge for increased accuracy. 2.
Tires, Wheels and Loading Low Tire Pressure Possible cause Warning Light Flashing Warning Spare tire in use Light (flashes for 20 to 30 seconds either at start-up or while driving) TPMS malfunction Customer Action Required Your temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality. For a description of how the system functions under these conditions, refer to Changing tires with TPMS in this section.
Tires, Wheels and Loading How temperature affects your tire pressure The Tire Pressure Monitoring System (TPMS) monitors tire pressure in each pneumatic tire. The pressure in each tire is dependent upon several factors, one of them being the contained air temperature (temperature of the air inside the tire). As the contained air temperature increases, the tire pressure also increases.
Tires, Wheels and Loading Follow these guidelines when using snow tires and chains: • Use only cable type SAE Class “S” chains. Conventional link or other type chains may cause damage to your vehicle’s wheelhouse and/or underbody. • These cable type chains should only be applied to the front wheels. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label). Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Tires, Wheels and Loading mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your authorized dealer (or the RV and Trailer Towing Guide provided by your authorized dealer) for more detailed information. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
Tires, Wheels and Loading capacity to carry you, 4 of your friends and all the golf bags? You and four friends average 220 lb. (99 kg) each and the golf bags weigh approximately 30 lb. (13.5 kg) each. The calculation would be: 1400 – (5 x 220) – (5 x 30) = 1400 – 1100 – 150 = 150 lb. Yes, you have enough load capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kg — (5 x 99 kg) — (5 x 13.5 kg) = 635 — 495 — 67.5 = 72.5 kg.
Tires, Wheels and Loading A new underbody wiring harness (14406) will be a component to this kit and will need to be installed, if applicable, per instructions located in the service kit.
Tires, Wheels and Loading Vehicle towing capability/Trailer hitch requirement Model/ Engine GCWR lb. (kg) Wagon, 4.2L 7200 (3266) Trailer Trailer Weight range Tongue load - lb. (kg) Class I 0-2000 10 - 15% of TW Non-Equalizing (0-907) (200 lb. [91 kg] Weight maximum) Carrying 0–3500 10 - 15% of TW Class II Non-Equalizing (0-1588) (350 lb. [159 kg] maximum) Weight Carrying Hitch type required Wagon, 4.
Tires, Wheels and Loading If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Be sure your trailer conforms to all applicable local and Federal Regulations regarding trailer braking. If your trailer is equipped with electronically controlled brakes you will need to have an electronic brake controller with associated wiring installed to your vehicle by an authorized dealer.
Tires, Wheels and Loading Understanding the gearshift positions of the 4–speed automatic transmission in the Driving chapter. • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to your Scheduled Maintenance Information for more information.
Tires, Wheels and Loading RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Front Wheel Drive (FWD) vehicles: It is not recommended to tow front wheel drive vehicles with the front drive wheels on the ground.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving • Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START) 4 without pressing the accelerator 3 pedal and release as soon as the 5 engine starts.
Driving Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.5 cm) or adjust the heating or air conditioning to bring in fresh air. USING THE ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant which aids in starting and heater/defroster performance. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -10°F (-23°C) or below.
Driving ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates ABS when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, ! P normal braking is still effective. (If your BRAKE warning lamp BRAKE illuminates with the parking brake released, have your brake system serviced immediately by an authorized dealer.
Driving Parking brake To set the parking brake, pull the handle up as far as possible. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. To release, press and hold the button, pull the handle up slightly, then push the handle down. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
Driving • • • • Maneuvering quickly to avoid an accident, pedestrian or obstacle Hitting a patch of ice Changing lanes on a snow-rutted road Entering a snow-free road from a snow-covered side street, or vice versa • Entering a paved road from a gravel road, or vice versa • Hitting a curb while turning • Cornering at excessive speeds while towing a heavily loaded trailer (refer to Trailer Towing in this chapter) The AdvanceTrac威 system automatically turns on when the engine is started.
Driving • A slight deceleration of the vehicle • The TRAC ACTIVE indicator light will illuminate • If your foot is on the brake pedal, you will feel a vibration in the pedal. • If the driving condition is severe and your foot is not on the brake, the brake pedal will move to apply higher brake forces. You may also hear a whoosh of air from under the instrument panel during this severe condition. All these conditions are normal during AdvanceTrac威 operation.
Driving If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steering seem to wander/pull.
Driving Do not drive your vehicle until you verify that the brakelamps are working. Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer.
Driving To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle.
Driving When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running. If you do not take these precautions, your vehicle may move unexpectedly and injure someone.
Driving FORWARD AND REVERSE SENSING SYSTEM The forward and reverse sensing system will warn the driver of obstacles within a certain range of the front and rear bumpers. The front sensors will be active when the gearshift is in any position other than P (Park) and the vehicle speed is below 8 mph (13 km/h). The rear sensors will only be active when the gearshift is in R (Reverse). The front sensors cover an area up to 31.
Driving The reverse sensing portion of the system detects obstacles up to 6 ft. (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the system detects a stationary or receding object further than 10 inches (25.
Driving This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground. Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the forward and reverse sensing system may create false beeps.
Driving The system is automatically enabled OFF when the gear selector is placed in D (Drive) or R (Reverse) and the ignition is ON. The park aid disable switch allows the driver to disable the system only when the ignition is ON, and the gear selector is in D (Drive) or R (Reverse). The OFF indicator remains illuminated when the system is disabled. If the indicator light illuminates when the system is enabled, it may indicate a failure in the RSS.
Roadside Emergencies ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty.
Roadside Emergencies U.S. Ford or Mercury vehicle customers who require roadside assistance, call 1–800–241–3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
Roadside Emergencies This switch is located behind the service panel on the right side of the cargo area. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6. Make another check for leaks. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 Fuse Amp Rating Relay Relay 10A 5A 20A 6 5A 7 8 10A 10A 9 10A 10 11 5A 5A Passenger Compartment Fuse Panel Description Accessory delay relay 1 Accessory delay relay 2 Front wiper motor Run feed B+ feed to outside mirrors Vent window power feed/Radio feed Driver door switch illumination/Passenger door switch illumination Rear wiper Run feed Cluster/Electronic Automatic Temperature Control (EATC) B+ feed, DVD Passive
Roadside Emergencies Fuse/Relay Location 12 Fuse Amp Rating 5A 13 5A 14 5A 15 16 10A 5A 17 10A 18 10A 19 5A 20 10A 21 10A 232 2006 Monterey (mty) Owners Guide (post-2002-fmt) USA (fus) Passenger Compartment Fuse Panel Description Brake-Shift Interlock (BSI) Run feed, Climate control system Run feed Compass/Driver heated seat/Passenger heated seats/Reverse sensing system/Power Liftgate Module/Power sliding door Run feeds Underhood fuse box Run feed, Front blower Run feed Brake On-Off (BOO
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies Fuse/Relay Location 3 4 5 6 Fuse Amp Rating 30A** 30A** 30A** 30A** 7 8 30A** 40A** 9 10 30A** 30A** 11 12 13 14 30A** 40A** 40A** 30A** 15 16 20 30A** 30A** Mini relay 21 22 23 24 25 26 27 28 29 30 31 32 Mini relay Micro relay Micro relay Mini relay Micro relay Micro relay — Mini relay Micro relay Micro relay Micro relay Mini relay 234 2006 Monterey (mty) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description Left cooling fan Starter solenoid Right-hand
Roadside Emergencies Fuse/Relay Location 40 Fuse Amp Rating 15A* 41 42 43 25A* 10A* 15A* 44 45 46 47 10A* 15A* 20A* 15A* 48 49 50 51 15A* 10A* 10A* 10A* 52 53 54 55 56 57 58 20A* 10A* 30A* 25A* 30A* — 30A* 59 60 20A* 30A* Power Distribution Box Description Engine #1 (A/C relay coil, IMRC, HEGO sensors, Canister purge, Transmission module) Horn A/C clutch Engine #2 (Cooling fan relays, Injectors, PCM, MAF sensor, IAC, Ignition coil, ESM) Heated PCV High beams Trailer stop/turn lamps Fuel pump, Fu
Roadside Emergencies Fuse/Relay Location 61 62 Fuse Amp Rating — 30A* 63 20A* 64 65 20A* 30A* 66 20A* 67 20A* 70 — 71 — 72 — 73 — 74 — 75 Diode 76 Diode * Mini Fuse ** Cartridge Fuse 236 2006 Monterey (mty) Owners Guide (post-2002-fmt) USA (fus) Power Distribution Box Description Not used SJB #3 – Right cornering/auxiliary lamps, Right low beam, Left front park/turn lamps, Left rear park/stop/turn lamps, Instrument panel courtesy lamps, Step well lamps, Left signal mirror, Clock, Cluster, Message
Roadside Emergencies Auxiliary relay box (cooling fans) The relay box is located in the engine compartment by the radiator.
Roadside Emergencies The use of tire sealants may damage your tires. The use of tire sealants may also damage your Tire Pressure Monitoring System and should not be used. Your vehicle is equipped with a Tire Pressure Monitoring System. Refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function. Temporary spare tire information Your vehicle may have a temporary spare tire.
Roadside Emergencies • ground clearance and parking at curbs • Winter driving capability Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only.
Roadside Emergencies • Winter weather driving capability • Wet weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire. If 4WD operation is necessary, do not operate above speeds of 10 mph (16 km/h) or for distances above 50 miles (80 km). 3.
Roadside Emergencies Have a flat tire serviced by an authorized dealer in order to prevent damage to the TPMS sensor, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. The spare tire and tools for your vehicle are stowed in the following locations: Item Spare tire Jack Jack handle Flat tire tether, wing screw Location Under the vehicle, just forward of the rear bumper.
Roadside Emergencies 2. Turn the wrench counterclockwise until cable is slack and tire can be slid rearward. 3. Remove the primary retainer from the center of the tire. Note: Do not stow the full size tire or any flat tire under the vehicle. Stowing the primary tether Note: If no tire is to be stowed under the vehicle, raise the primary tether by turning the wrench clockwise until the hex nut ratchets.
Roadside Emergencies 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine off, and block the diagonally opposite wheel. 3. Remove the spare tire, jack and lug wrench. 4. Removing the optional wheel cover or center ornament: • To remove a bolt-on wheel cover (if equipped) loosen the plastic nuts on the center ornament with the wheel nut wrench. Then, remove the wheel cover with the tapered end of the wheel nut wrench.
Roadside Emergencies If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area. 6. Locate the jack notch next to the door closest to the tire you are changing, then place the jack on the frame rail directly behind the notch. 7. Turn the jack handle clockwise until the wheel is completely off the ground.
Roadside Emergencies 11. Remove the jack and fully 1 tighten the lug nuts in the order shown. Refer to Wheel lug nut torque specifications later in this 3 4 chapter for the proper lug nut torque specification. 12. Installing the optional wheel cover or center ornament: 5 2 • If equipped with a bolted-on wheel cover, install the wheel cover and tighten the five plastic nuts until they click (do not use power tools on these nuts).
Roadside Emergencies The effort to turn the jack handle increases significantly and the spare tire carrier ratchets or slips when the tire is raised to the maximum tightness. Tighten to the best of your ability, to the point where the ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your authorized dealer for assistance at your earliest convenience. 5.
Roadside Emergencies JUMP STARTING The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter.
Roadside Emergencies Connecting the jumper cables + + – – 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Roadside Emergencies + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Roadside Emergencies 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed by wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Roadside Emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Lincoln or Mercury vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repairs require special training and/or equipment, so not all authorized dealers are authorized to perform all warranty repairs.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealer to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the Warranty Guide. However, if your warranty concern has not been resolved using the three-step procedure, you may be eligible to participate in the BBB AUTO LINE program.
Customer Assistance trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: • a non-Ford product • a non-authorized dealership • sales disputes between customer and authorized dealer except those associated with warranty repairs or concerns with the vehicle’s performance as designed • a request for reimbursement of consequential expenses unless a service or product concern is being reviewed • items not covered by the New Vehicle Limit
Customer Assistance Your application is reviewed and, if it is determined to be eligible, you will receive an acknowledgment indicating: • The file number assigned to your application. • The toll-free phone number of the DSB’s independent administrator. Your authorized dealer and a Ford Motor Company representative will then be asked to submit statements.
Customer Assistance After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the authorized dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Customer Assistance CAMVAP services are available in all territories and provinces. For more information, without charge or obligation, call your CAMVAP Provincial Administrator directly at 1-800-207-0685. FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage.
Customer Assistance If your vehicle must be serviced while you are traveling or living in Central America, the Caribbean, or the Middle East, contact the nearest authorized dealer. If the authorized dealer cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest authorized dealer.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their shine: • Clean weekly with Motorcraft Wheel and Tire Cleaner (ZC-37–A), which is available from your authorized dealer.
Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42).
Cleaning • The wiper blades can be cleaned with isopropyl (rubbing) alcohol or Motorcraft Premium Windshield Washer Concentrate (ZC-32–A), available from your authorized dealer. This washer fluid contains special solution in addition to alcohol which helps to remove the hot wax deposited on the wiper blade and windshield from automated car wash facilities. Be sure to replace wiper blades when they appear worn or do not function properly. • Do not use abrasives, as they may cause scratches.
Cleaning • Remove light stains and soil with Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14). • If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set.
Cleaning quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod. Your vehicle’s hood has two locations for the prop rod to be placed. These locations provide two different hood opening positions. Use the location which best suits your needs.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engines 10 9 2 1 8 7 6 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8. Windshield washer fluid reservoir 9. Engine coolant reservoir 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing. Refer to Lubricant specifications in this chapter.
Maintenance and Specifications CHANGING THE WIPER BLADES To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at least once per year for optimum performance.
Maintenance and Specifications 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter.
Maintenance and Specifications • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity.
Maintenance and Specifications economy requirements of the International Lubricant Standardization and Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Maintenance and Specifications If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals. If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water.
Maintenance and Specifications installed, the transaxle must relearn its adaptive strategy. Optimal shifting will resume within a few hundred kilometers (miles) of operation. Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance. To begin this process: 1.
Maintenance and Specifications R TU LE AD RE N • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. RECYCLE ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in scheduled maintenance information.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (U.S.
Maintenance and Specifications coolant degas system with a pressurized cap, or if it is necessary to remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1.
Maintenance and Specifications Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section.
Maintenance and Specifications FUEL FILTER For fuel filter replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter. Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Maintenance and Specifications Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Maintenance and Specifications Refueling • • • • • • Fuel vapor burns violently and a fuel fire can cause severe injuries.
Maintenance and Specifications If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Maintenance and Specifications Do not be concerned if your engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized dealer to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems, try a different brand of unleaded gasoline.
Maintenance and Specifications possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,000 miles (1,600 km) of driving (engine break-in period). You will get a more accurate measurement after 2,000 miles-3,000 miles (3,000 km–5,000 km).
Maintenance and Specifications 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled.
Maintenance and Specifications • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items.
Maintenance and Specifications expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed.
Maintenance and Specifications it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your Warranty Guide for complete emission warranty information. On board diagnostics (OBD-II) Your vehicle is equipped with a computer that monitors the engine’s emission control system.
Maintenance and Specifications condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle.
Maintenance and Specifications BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of your brake system could be compromised; seek service from your authorized dealer immediately.
Maintenance and Specifications 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperatures 150°F-170°F (66°C-77°C) on a level surface.
Maintenance and Specifications Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter.
Maintenance and Specifications 2. Loosen the hose clamp located closest to the air cleaner. 3. Remove the air cleaner assembly from the vehicle. 4. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 5. Remove the air filter element from the air filter housing. 6. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.
Maintenance and Specifications 7. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. 8. Replace the air filter housing cover and secure the clamps. Be sure all the tabs on the bottom edge are properly aligned. 9. Reinstall the air cleaner assembly into the vehicle. Ensure the tabs on the inlet tube are secure in the sheet metal.
Maintenance and Specifications 10. Ensure the pads on the bottom of the air cleaner assembly are properly seated. 11. Reconnect the outlet tube to the air cleaner assembly and tighten the clamp. 12. Reconnect the Mass Air Flow Sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in “locked” position.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery Oil filter PCV valve Spark plugs 4.2L OHV V6 engine FA-1679 FG-986B BXT-59 BXT-65-750 FL-400S 1 2 1 The PCV valve is a critical emission component. It is one of the items listed in scheduled maintenance information and is essential to the life and performance of your vehicle and to its emissions system. For PCV valve replacement, see your authorized dealer.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid Engine oil (includes filter change)3 Engine coolant 2 Ford Part Name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid1 Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) Motorcraft Premium Gold Engine Coolant (yellow-colored) Power steering fluid Fuel tank Motorcraft MERCON威 ATF N/A Automatic transaxle fluid Motorcraft MERCON威V ATF Motorcraft Premium Windshield
Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Ford part name Brake fluid Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid1 Door Silicone weatherstrips Spray Lubricant Engine Motorcraft coolant Premium Gold Engine Coolant (yellow colored) Engine oil Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) Ford part number PM-1 Ford specification XL-6 ESR-M13P4-A VC-7-A (U.S.
Maintenance and Specifications Item Ford part Ford part name number Multi-Purpose XG-4 or XL-5 Grease Door latch, hood latch, auxiliary hood latch, door and liftgate hinges, striker plates, seat tracks, sliding door both sides (upper and lower track) and fuel filler door hinge.
Maintenance and Specifications Item Windshield washer fluid Ford part name Motorcraft Premium Windshield Washer Concentrate Ford part number ZC-32–A Ford specification WSB-M8B16–A2 1 Use only brake fluids certified to meet Ford specifications. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used. 2 Ensure the correct automatic transmission fluid is used MERCON威 and MERCON威V are not interchangeable. DO NOT MIX MERCON威 and MERCON威V.
Maintenance and Specifications 307 2006 Monterey (mty) Owners Guide (post-2002-fmt) USA (fus)
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake type and Gross Vehicle Weight Rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number TRANSMISSION/TRANSAXLE CODE DESIGNATIONS You can find a transmission/transaxle code on the Safety Compliance Certification Label .
Accessories MERCURY ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Mercury Accessories are available for your vehicle through your local authorized Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Rear seat entertainment systems - DVD Ash cup/coin holder Trailer hitches, wiring harnesses and accessories Roof carriers Peace of mind First aid and safety kits Full vehicle covers Locking gas cap Remote start Vehicle security systems Mobile-Ease娂 hands-free communication system For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed t
Index A Accessory delay ..........................64 AdvanceTrac ..............................216 Air cleaner filter ...............298, 302 Air filter, cabin ............................40 Airbag supplemental restraint system ................147–148, 156, 158 and child safety seats ............149 description ..............148, 156, 158 disposal ....................................161 driver airbag ............150, 157, 159 indicator light .................156, 161 operation .................
Index wiper blades ............................266 Clock ............................................62 Compass, electronic ....................55 calibration .................................56 set zone adjustment .................56 Console ........................................71 overhead ..............................54–55 Controls power seat ...............................110 steering column ........................70 Coolant checking and adding ..............280 refill capacities ................
Index cap ...........................................287 capacity ...................................303 choosing the right fuel ...........288 comparisons with EPA fuel economy estimates .................292 detergent in fuel .....................289 filling your vehicle with fuel ..................285, 287, 290 filter, specifications ........285, 302 fuel pump shut-off switch .....228 improving fuel economy ........289 octane rating ...................288, 306 quality .....................................
Index headlamps .................................41 headlamps, flash to pass ..........43 instrument panel, dimming .....44 interior lamps .....................46–48 replacing bulbs ...................48–52 Lane change indicator (see Turn signal) ........................46 Liftgate ............................83, 87, 95 Lights, warning and indicator ....10 anti-lock brakes (ABS) ..........215 Load limits .................................199 Locks autolock ...................................102 childproof ..
Index Safety belts (see Safety restraints) ..........133, 136, 138–140 Safety Canopy ...........................158 Safety defects, reporting ..........263 Safety restraints ...........133, 136, 138–140 belt minder .............................142 extension assembly ................146 for adults .........................138–140 for children .....................161–162 Occupant Classification Sensor ......................................134 safety belt maintenance .........
Index Turn signal ..................................46 V Vehicle dimensions ...................306 Vehicle Identification Number (VIN) ..........................................308 Vehicle loading ..........................199 Ventilating your vehicle ...........214 Washer fluid ..............................273 Water, Driving through .............226 Windows power .........................................64 rear wiper/washer .....................53 W Windshield washer fluid and wipers ..................
