Table of Contents Introduction Instrument Cluster 4 10 Warning and control lights Gauges 10 15 Entertainment Systems 17 AM/FM stereo with CD AM/FM stereo cassette with CD Climate Controls Manual heating and air conditioning Rear window defroster Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 17 23 30 30 40 41 41 46 48 53 53 54 65 66 68 76 Locks and Security 91 K
Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Tires, Wheels and Loading Tire Information Changing tires Wheel lug nut torque Low tire warning system Vehicle loading Trailer towing Recreational towing Driving 109 109 128 142 155 167 168 172 182 191 194 201 205 206 Starting Brakes Transmission operation 206 210 214 Roadside Emergencies 222 Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Jump starting W
Table of Contents Cleaning 248 Maintenance and Specifications 254 Engine compartment Engine oil Battery Engine Coolant Fuel information Air filter(s) Part numbers Refill capacities Lubricant specifications 256 257 261 263 268 281 285 286 287 Accessories 293 Index 295 All rights reserved.
Introduction CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.
Introduction SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger air bag.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Windows Front/Rear Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap Low tire warning MAX MIN 9 2
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Check engine warning light to come on, refer to Fuel filler cap in the Maintenance and Specification chapter.
Instrument Cluster Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Check transaxle: Illuminates when a transaxle problem has been detected and shifting may be restricted. If the light remains on, have the system serviced immediately. Charging system: Illuminates when the battery is not charging properly.
Instrument Cluster Traction Control娂 or TRAC AdvanceTrac威 off light (if OFF equipped): Illuminates when the Traction Control娂 has been disabled (by the driver or as a result of a system failure). Refer to the Driving chapter for more information. Low tire warning: Illuminates when your tire pressure is low. If the light remains on at start up or while driving, the tire pressure should be checked. Refer to Inspecting and Inflating Your Tires in the Tires, Wheels and Loading chapter.
Instrument Cluster Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb. Bulb warning: Displays which bulb is burned out. Depress the RESET control to clear. High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’s door is opened.
Instrument Cluster GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. Never remove the coolant reservoir cap while the engine is running or hot.
Instrument Cluster Odometer: Registers the total miles (kilometers) of the vehicle. Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English. Trip odometer: Registers the miles (kilometers) of individual journeys. To reset, press and hold the message center RESET button for three seconds to reset. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: / Treble: Press to adjust the treble setting. Use Bass: Press to adjust the bass setting. Use / / / SEEK SEEK . .
Entertainment Systems Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU / / SEEK to adjust. to access and use Setting the clock: Your vehicle is equipped with an in-dash clock; Refer to “Setting the clock” in the Driver Controls chapter for further information. Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press / / SEEK to set.
Entertainment Systems 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume.
Entertainment Systems AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press / / SEEK to set. MENU to access.
Entertainment Systems Treble: Press to adjust the treble setting. Use / / SEEK . Balance: Press to adjust the audio between the left and right speakers. / / SEEK . Use Fade: Press to adjust the audio between the front and rear speakers. / / SEEK . Use Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind / / SEEK to adjust. noise.
Entertainment Systems 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16.
Entertainment Systems AM/FM STEREO WITH CASSETTE/CD (IF EQUIPPED) / Tuner: Press to 1. manually go up or down the radio frequency. Also use in menu mode to select various settings. 2. Seek:Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 4. Menu: Press to toggle through the following modes: Treble: Press to adjust the treble setting. Use / / SEEK . / / SEEK . Bass: Press to adjust the bass setting.
Entertainment Systems Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK . Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Press MENU to access and use / / SEEK to adjust. Setting the clock: Your vehicle is equipped with an in-dash clock. Refer to “Setting the clock” in the Driver Controls chapter for further information.
Entertainment Systems 9. Compress (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level. 10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a CD track. 12. Rewind: Press to manually reverse in a CD track. 13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 14. Tape: Insert a tape facing to the right. 15.
Entertainment Systems 19. CD eject: Press to eject a CD. 20. CD slot: Insert a CD label side up. 21. Seek:Press to access the previous strong station or track. 22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. AUXILIARY AUDIO CONTROLS (IF EQUIPPED) Your vehicle may be equipped with auxiliary audio controls. This feature allows the front and middle seat passengers to listen to different media sources (radio, cassette, CD or DVD) simultaneously.
Entertainment Systems If there is a discrepancy between the rear seat controls and the front audio controls (such as both trying to listen to the same playing media), the front audio system will receive the desired selection. To activate Dual Play mode (rear seat passengers listen to a different playing media than the front seat passengers): • Press the speaker/headphone control. • Press MEDIA to change audio sources (for headphone mode only).
Entertainment Systems RADIO FREQUENCIES AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.
Entertainment Systems CD/CD PLAYER CARE Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleaner and wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • For vehicles equipped with a six disc CD changer, don’t insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion.
Climate Controls DUAL ZONE MANUAL HEATING AND AIR CONDITIONING SYSTEM WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents only to cool the vehicle. This re-cooling of the interior air is more economical and efficient.
Climate Controls will be warmer or cooler than the driver airflow temperature setting REAR ) is when more than one rear temperature light ( illuminated. Rear defroster: Press to activate/deactivate rear window 5. R defroster. Refer to Rear window defroster later in this chapter for more information. Recirculated air: Press to activate/deactivate air recirculation 6. in cabin.
Climate Controls • For maximum cooling performance (MAX A/C): In the MAX A/C mode: • Move the temperature control selector to the coldest setting. • Set the fan to the highest speed initially, then adjust to maintain passenger comfort. and In the modes: • Move the temperature control selector to the coldest setting. • Select A/C and recirculated air colder airflow. . Use with A/C to provide • Set the fan to the highest speed initially, then adjust to maintain passenger comfort.
Climate Controls DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls engaged manually in any airflow selection except may turn off automatically in all airflow selections. . Recirculated air 7. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO, , and . : Distributes air through the windshield defroster vents and floor 8. vents. 9. : Distributes air through the floor vents. : Distributes air through the instrument panel vents and the floor 10. vents.
Climate Controls DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH HEATED SEATS AND REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster vents. Can be used to clear thin ice or fog from the windshield. 2. Rear temperature control: Press to enable the auxiliary system and set the desired rear cabin airflow temperature with the front control.
Climate Controls 7. :Distributes air through the windshield defroster vents and the floor vents. 8. : Distributes air through the floor vents. 9. : Distributes air through the instrument panel vents and the floor vents. 10. : Distributes air through the instrument panel vents. 11. Manual override controls: Allows you to change the system operation. To return to full automatic control, press AUTO. 12. Driver heated seat control: Press once to activate the high heat setting (2 indicator lights).
Climate Controls 19. REAR: Press to enable the control located in the rear seat. Press again to turn the auxiliary system off. DUAL AUTOMATIC TEMPERATURE CONTROL WITH HEATED AND COOLED SEATS AND REAR PASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) Defrost: Distributes outside air through the windshield defroster 1. vents. Can be used to clear thin ice or fog from the windshield. 2.
Climate Controls 6. Passenger heated seat control: Press once to activate the high heat setting (2 indicator lights). Press again to activate the low heat setting (1 indicator light). Press again to deactivate the passenger heated seat. 7. Passenger cooled seat control: Press once to activate the high cool setting (2 indicator lights). Press again to activate the low cool setting (1 indicator light). Press again to deactivate the passenger cooled seat. 8.
Climate Controls 16. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO, , and . 17. REAR: Press to enable the control located in the rear seat. Press again to turn the auxiliary system off. 18. Recirculated air: Press to activate/deactivate air recirculation in the vehicle cabin.
Climate Controls 3. Adjust the temperature control to maintain comfort. 4. Set the fan to the highest speed. 5. Direct the outer instrument panel vents towards the side windows. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. AUXILIARY CLIMATE CONTROL (IF EQUIPPED) 1. Fan speed: Turn to select the desired fan speed. 2.
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. P Turns the headlamps on. PULL Note: Some vehicles may be equipped with a headlamps on with wipers feature. In order for this feature to work: • the ignition must be in run and the front wipers must be on greater than 10 seconds except during a mist wipe or while the wipers are on to clear washer fluid during a wash condition.
Lights Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a fixed period of time after the ignition switch is turned to OFF. • To turn autolamps on, rotate the . control counterclockwise to • To turn autolamps off, rotate the control clockwise to .
Lights • and the transmission must be out of PARK. Always remember to turn on your headlamps at dusk or during inclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision. High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.
Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Rotate the thumbwheel from left to right to brighten the instrument panel. • Rotate the thumbwheel from right to left to dim the instrument panel. Your vehicle also contains a feature called “sleeping baby mode” — in which the dome lamps will remain off and only the lower lamps will illuminate.
Lights • (1) 8 feet (2.4 meters) • (2) Center height of lamp to ground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height from the center of your headlamp to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well). The center of the lamp is marked by a 0.5 mm circle on the headlamp lens. 3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. 4.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS The interior lights illuminate when: • any door is opened (and the operation switch is in the middle position). • the instrument panel dimmer switch is moved to the passenger side position (right position). • any of the remote entry controls are pressed and the ignition is OFF (and the operation switch is in the middle position).
Lights Second row & third row dome and map lamps (if equipped) The second row dome and map lamps are located overhead, above the second row passenger seats. The dome lamp will stay on if the panel dimmer control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the driver’s side position, the lamp will not come on at all. The dome lamp will illuminate whenever a front door is opened.
Lights Cargo lamp The cargo lamp will stay on if the control is moved to the driver side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the passenger’s side position, the lamp will not come on at all. With the ignition key in the ACCESSORY or ON position, the rear cargo lamp can be turned ON or OFF by sliding the control. BULBS Headlamp Condensation The headlamps are vented to equalize pressure.
Lights Function Trade Number Backup lamps 3156K Dome lamp (first row) 10W sofitte Cargo lamp 10W sofitte Map lamps (second row) H6W Dome lamp (third row) 10W sofitte Map lamps (overhead console) 906 Stepwell lamp T-562 Front seat footwell 194 Front door mounted courtesy lamp 168 Visor vanity lamp - Slide on Rail system 37 (SOR) All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. Replacing headlamp bulbs To remove the headlamp bulb: 1.
Lights 3. Disconnect the electrical connector from the bulb by pulling rearward and unlock the bulb by rotating it counterclockwise. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated. Install the new bulb(s) in reverse order. Replacing front parking/turn/sidemarker signal bulbs 1.
Lights Replacing tail lamp/backup/turn lamp bulbs 1. Make sure the headlamp switch is in the OFF position and open the liftgate to expose the tail lamp assembly, then remove the retaining screws for the lamp assembly. 2. Carefully remove the lamp assembly. 3. Rotate bulb socket counterclockwise and remove from lamp assembly. 4. Pull bulb straight out of socket and push in new bulb. Install the new bulb(s) in reverse order.
Lights Replacing foglamp bulbs 1. Make sure the foglamp switch is in the OFF position. 2. Remove the bulb socket from the foglamp by turning counterclockwise. If a plastic tie strap restricts the rotation of the bulb socket and connector, cut the strap. Replacement of the strap is not necessary. 3. Disconnect the electrical connector. Install the new bulb in reverse order.
Driver Controls MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three times with washer fluid. • a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.
Driver Controls Changing the wiper blades 1. Pull the wiper arm away from the vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 2. Attach the new wiper to the wiper arm and press it into place until a click is heard. Replace wiper blades at least once per year for optimum performance.
Driver Controls ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamp. Slide on rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package.
Driver Controls overhead console. When the vehicle is turned off, the electronics display will remember the last display state. Outside air temperature The temperature can be displayed in either Centigrade or Fahrenheit. This is controlled via the Message Center. Please refer to the Message Center in this chapter to change from English to metric. The ignition key must be in the ON or ACCESSORY position.
Driver Controls 3. Press and hold the momentary push-button for approximately 4 seconds, until VAR is displayed, then release it. (Pressing the momentary push-button for 8 seconds de-calibrates the compass—see Compass Calibration Mode). 4. Press the button to increment the VAR number to the desired VAR number. Wait 5 seconds without button activity and the compass will return to the heading mode.
Driver Controls SLIDING DOOR OPERATION Manual door operation If equipped with a Power Sliding Door (PSD), turn the Power Door Lockout control on the overhead console to the OFF position. Refer to the Disabling power operation of the PSD section in this chapter for more information. Note: Before unlatching the left side door, verify that the fuel fill door is closed. The left hand door will not open if the fuel door is open. Slide the door carefully in a controlled manner to the full open position.
Driver Controls Do not operate vehicle with the door in the open position. Abrupt vehicle acceleration or deceleration could cause the door to move suddenly and could result in personal injury or damage to the door. If the vehicle is parked on a downhill grade, the door could slam shut and could result in injury or damage to the door. Ensure that the open door is secure against the stop before allowing passengers to enter or exit the vehicle.
Driver Controls To power open or close the PSD from the Overhead console: Push and release the overhead console right or left hand control. Pressing this control will also simultaneously unlock all doors. To power open or close the PSD from the second row passenger control switch: • Ensure that the PSD is unlocked, using the key fob or power door unlock. Refer to Remote Entry System in the Locks and security chapter. • Push and release the right or left hand second row passenger control.
Driver Controls Disabling PSD power operation Pressing the Power Door Lockout Control to the OFF position prevents power operation of the PSD using the rear seat control(s), inside or outside handle or by manually moving the door. With the PSD rear controls disabled, the door(s) can be opened manually with the inside or outside handles. With the Power Door Lockout control in the OFF position, the overhead console right and left hand controls and the Remote Entry System remain functional.
Driver Controls 4. Wait five (5) seconds and close the door by pressing the PSD control on the overhead console. 5. Wait five (5) seconds and repeat Steps 3 and 4 then go on to step 6. 6. Repeat steps 3–5 for opposite door. If the door still does not operate correctly: 7. Ensure the ignition is in the OFF position 8. Remove the PSD fuse (fuse #11) from the passenger fuse panel and leave it out for thirty (30) seconds. Refer to the chapter on Fuses and Relays.
Driver Controls INSTRUMENT PANEL STORAGE COMPARTMENT The storage compartment may be used to secure sunglasses or similar sized objects. Press the control to open the storage compartment. CLOCK (IF EQUIPPED) Press the right + control to move the time display forward. Press the left - control to move the time display backwards. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only.
Driver Controls There are up to three auxiliary power points in the following locations: • Located on the instrument panel. • Located next to the second row seat. • Located on the right trim panel in the rear cargo area. Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket.
Driver Controls POWER WINDOWS Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.
Driver Controls Power vent windows The power vent windows are operated by a single switch located on the instrument panel. Press and hold the bottom of the switch to open or the top of the switch to close both vent windows. A sound will be heard when opening and closing the vent windows. This is a normal noise that informs you the windows are operating. MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle may be equipped with an inside rear view mirror with an auto-dimming function.
Driver Controls Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Signal indicator mirrors (if equipped) When the turn signal is activated, the appropriate mirror will show a blinking yellow arrow.
Driver Controls POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you. The adjustment allows for approximately 2.8 inches (73 mm) of maximum travel. Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.
Driver Controls 3. Press the SET + control and release it. 4. Take your foot off the accelerator pedal. light on the 5. The indicator instrument cluster will turn on. Note: • Vehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed. • If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.
Driver Controls • Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control. Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the CST - control until you get to the desired speed, then release the control. You can also use the CST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).
Driver Controls STEERING WHEEL CONTROLS (IF EQUIPPED) RADIO CONTROL FEATURES • Press MEDIA to select AM, FM1, FM2, TAPE or CD (if equipped). In Radio mode: • Press SEEK to access the next/previous strong station. In Tape mode: • Press SEEK to listen to the next selection on the tape. In CD mode: • Press SEEK to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust the volume. • Press MUTE to mute the volume.
Driver Controls Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in-vehicle communications systems, telematics devices and portable two-way radios. A driver’s first responsibility is the safe operation of the vehicle. The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.
Driver Controls Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section. Programming Do not program HomeLink威 with the vehicle parked in the garage.
Driver Controls 5. Press and hold the just-trained HomeLink威 button and observe the indicator light. If the light is constant, programming is complete and your device should activate when the HomeLink威 button is pressed and released. Note: To program the remaining two HomeLink威 buttons, begin with Step 2 in the “Programming” section — do not repeat Step 1.
Driver Controls signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal. • Proceed with Step 4 in the “Programming” section. Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.).
Driver Controls For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515. MESSAGE CENTER With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime.
Driver Controls Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display.
Driver Controls Trip elapsed drive time Select this function from the INFO menu to display your trip elapsed drive time. When selected the display will accumulate when the key is in the ON position. 1. Press the INFO control until the message center display shows the TRIP TIME XX:XX:XX. 2. Hold the RESET control down for two seconds to clear display. Display on/off Select this function from the INFO menu to turn the upper two lines of the message center display OFF or ON.
Driver Controls 3. Press and hold the RESET control for 2 seconds to set the language choice. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored.
Driver Controls System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warning messages.
Driver Controls Liftgate ajar Warning returns after the ignition key is turned from OFF to ON Check left park lamp Check right park lamp Check left headlamp Check fuel cap Check right headlamp Check left turn lamp Washer fluid low Check right turn lamp Change oil soon Check tires Check brake lamps Turn signal on reminder DRIVER’S DOOR AJAR. Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. LEFT REAR DOOR AJAR.
Driver Controls REDUCED ENGINE POWER. Displayed when the engine temperature exceeds safe driving operating range and the vehicle limits engine power to prevent engine damage. STOP ENGINE SAFELY. Displayed when the engine temperature exceeds safe driving operating range and the engine must be shut down to prevent damage. Stop the vehicle as soon as possible and turn off the engine. If this warning stays on, contact your dealer as soon as possible. CHECK BRAKE LAMPS.
Driver Controls CHANGE OIL SOON. Displayed when the engine oil life remaining is 5 percent or less. When oil life left is between 5% and 0%, the CHANGE OIL SOON message will be displayed. When oil life left reaches 0%, the OIL CHANGE REQUIRED message will be displayed. An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS.
Driver Controls To reset the oil monitoring system to your personalized oil life %: 1. Press the SETUP control to access the System Check function. 2. Press and release the RESET control to display “OIL LIFE XX% HOLD RESET NEW”. 3. Press and hold the RESET control for 2 seconds to display “IF NEW OIL HOLD RESET”. 4. Release the RESET control momentarily, then press RESET and SETUP controls at the same time to activate a service mode which will display “OIL LIFE XX% RESET TO ALTER”. 5.
Driver Controls LIFTGATE Unlock the liftgate (but not release it) with the power door lock system and remote entry transmitter. To open the liftgate, pull the liftgate handle rearward. • Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is opened, the liftgate could be damaged against a low ceiling. • Do not leave the liftgate open while driving.
Driver Controls Keep the keys out of the reach of children. Do not allow children to play on or near an open or moving power liftgate. Exercise care, when power opening or closing the PLG in a garage or other enclosed area with a low ceiling or close to a wall/garage door. The PLG could be damaged from the contact. Do not attempt to manually force the PLG to travel faster than the power system will permit.
Driver Controls To power open the PLG with outside release handle: 1. Ensure that the Power Door Lockout Control in the overhead console is ON. 2. Ensure that the PLG is unlocked, using the key fob or power door unlock. Refer to Remote Entry System in the Locks and security chapter. 3. Pull up on the liftgate handle to engage the power assist feature. Release the handle as soon as the PLG begins to power open.
Driver Controls PLG encounters an obstacle while opening, the PLG will stop when it encounters a solid obstacle. Close the liftgate manually and remove the obstruction. Normal operation can then be resumed. Resetting the PLG: The power liftgate may not operate properly if any of the following conditions occur • a low voltage or dead battery • disconnected battery • the liftgate has been left open or unlatched for more than six (6) hours If any of these conditions occur, the PLG must be reset.
Driver Controls CARGO AREA FEATURES Cargo net (if equipped) The cargo pouch net secures lightweight objects in the cargo area. Attach the net to the anchors provided. Do not put more than 50 lbs. (22 kg) in the net. The cargo net is not designed to restrain objects during a collision or heavy braking. Utility hooks The utility hooks can be used to hang small items. Do not hang more than 20 lb. (12 kg) on each of the hooks. The hooks are not designed to restrain objects during a collision.
Driver Controls To adjust the cross-bar (if equipped) position: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide cross-bar to the desired location and tighten the thumbwheel at both ends of the cross-bar. To remove the cross-bar (if equipped) assembly: 1. Loosen the thumbwheel (2) at both ends of the cross-bar (1) and slide the cross-bar (1) to the end of the side rails (4). 2.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock娂 passive anti-theft system section in this chapter for more information. POWER DOOR LOCKS Press control to unlock all doors. Note: When the perimeter alarm is armed, the power door locks “inhibit” state is enabled and this switch is disabled.
Locks and Security The vehicle can still be locked, with the key in the ignition, using the manual lock button on the door, locking the driver’s door with a key, by simultaneously pressing button 7 • 8 and the 9 • 0 controls on the remote entry keypad (if equipped), or using the lock button on the remote entry transmitter (if equipped). Childproof door locks • When these locks are set, the sliding doors cannot be opened with the inside handle.
Locks and Security • For vehicles without power liftgate, pull the lock/unlock lever to the right (drivers side). • For vehicles with power liftgate, pull the lock/unlock lever toward you (toward the front of the vehicle). Once the lock/unlock lever has been moved, you can open the liftgate from the outside liftgate handle. REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada.
Locks and Security • 3–button remote • 5–button remote • 6–button remote The remote entry system allows you to: • lock or unlock all vehicle doors and liftgate without a key. • unlock/open a driver’s side power sliding door and/or passenger side power sliding door (if equipped). • unlock/open the power liftgate (PLG) (if equipped). • activate the personal alarm. • arm and disarm the perimeter anti-theft system (if equipped).
Locks and Security If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to the dealership in order to aid in troubleshooting the problem. Unlocking the doors 1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate and the anti-theft system (if equipped) will disarm. and release again within three seconds to unlock all doors 2. Press and the liftgate.
Locks and Security Opening power liftgate (PLG) (if equipped) Press the control twice within three seconds to power open the power liftgate. The interior lamps will illuminate. Make sure all persons are clear of the power liftgate area before using the power liftgate controls to open or close the liftgate. Press the control another two times within three seconds to close the power liftgate and turn off the interior lights.
Locks and Security Sounding a panic alarm to activate the alarm. The alarm will cycle the horn, the turn Press signals will flash, and the interior lamps will illuminate. Press again or turn the ignition to the 4 (ON) or the 1 (ACCESSORY) position to deactivate. Replacing the battery The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: 1. Twist a thin coin between the two halves of the remote entry transmitter near the key ring.
Locks and Security Replacing lost remote entry transmitters If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure.
Locks and Security Illuminated entry The interior lamps illuminate when the key in the driver’s door lock cylinder, the keyless entry system or the remote entry transmitter is used to unlock the door(s), power sliding doors (if equipped) or liftgate. The illuminated entry system will turn off the interior lights if: • the ignition switch is turned to the 4 (ON) position, or • the keyless entry system or the remote entry transmitter lock control is pressed, or • after 25 seconds of illumination.
Locks and Security • the ignition is turned to the 4 (ON) position, or • after 25 seconds of illumination. Deactivating/activating perimeter lamps You may enable/disable this feature by having your vehicle serviced by your authorized dealer. You may also perform the following power door lock sequence to enable/disable the perimeter lamps feature: 1. Turn the ignition to the 4 (ON) position, then press the power door unlock control 3 times. 2.
Locks and Security 2. Press the SET control on the door next to the window inside from the mirror. 3. Within 5 five seconds, press any control on the remote transmitter and then press the 1 or 2 control on the driver’s door panel to associate with the Driver 1 or Driver 2 positions. 4. Repeat this procedure for another remote transmitter if desired. Disassociating the memory feature from the remote transmitter To deactivate this feature: 1. Press the SET control on the driver’s door panel. 2.
Locks and Security • marked on the passenger compartment fuse panel (located below and to the left of the steering, near the brake pedal), • and is available from your authorized dealer. You can also create your own 5–digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation. Programming a personal entry code To create your own personal entry code(s): 1. Enter the factory set code. Note: The driver’s door will unlock. 2.
Locks and Security • Do not use five numbers in sequential order. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds of entering the factory code, press and release the 1 • 2 control. The door locks will lock and quickly unlock to confirm entry into the programming mode. 3. Within five seconds of Step 2, press and hold the 1 • 2 for two seconds to erase the customer programmed code. The programming mode is exited after five seconds of keypad inactivity.
Locks and Security • the brake is depressed while vehicle speed is less than 5 mph (8 km/h), • all vehicle doors become closed again, and • then the vehicle increases to more than 5 mph (8 km/h). Deactivating/activating the autolock feature The deactivating/activating the autolock feature can be turned off by the keyless entry keypad (if equipped) on your door, driver configuration mode or by your dealer.
Locks and Security 7. Turn the ignition to the 3 (OFF) position. The horn will chirp once to confirm the procedure is complete. SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems.
Locks and Security If your keys are lost or stolen, you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to an authorized Ford dealer or a locksmith. The key codes will need to be erased from your vehicle and new codes will need to be re-coded. Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience.
Locks and Security 5. Within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 3 (OFF) position to the 4 (ON) position [maintain ignition in the 4 (ON) position for at least three seconds, but no more than ten seconds]. This step will program your new key to a coded key. 6. To program additional new unprogrammed key(s), repeat this procedure from step 1.
Locks and Security • Unlock the vehicle with the keyless entry keypad. • Unlock the vehicle with a key in the driver’s door lock cylinder. • Use a SecuriLock娂 key to move the ignition to the 4 (ON) or 5 (START) position.
Seating and Safety Restraints SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Adjustable head restraints Head restraints help to limit head motion in the event of a rear collision. Adjust your head restraint so that it is located directly or as close as possible behind your head.
Seating and Safety Restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop.
Seating and Safety Restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on the climate control system panel once to activate high heat. • Push twice to activate low heat. • Push a third time to deactivate. The indicator light on the control will illuminate when activated.
Seating and Safety Restraints • Push again to operate the heated/cooled system at a lower level. • Push again to deactivate. The climate controlled seat system includes an air filter that has to be replaced periodically. Refer to the Schedule Maintenance Guide for more information. Do not run heated/cooled system with the filter removed. Using the manual lumbar support (if equipped) The lumbar control is located on the inboard side of the seat under the armrest.
Seating and Safety Restraints A position can only be recalled when the transmission gearshift is in Park. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remote entry transmitter UNLOCK control if the transmitter is programmed to a memory position or when you enter a valid personal entry code that is programmed to a memory position.
Seating and Safety Restraints Seat mounted cup holders (if equipped) Deploy by pressing the button on top of the cupholder. The cupholder is designed to detach from the seat when subjected to heavy load. The cupholder can be reinstalled by returning to the closed position. Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Seating and Safety Restraints Adjusting 2nd row seats (if equipped) Lift control to adjust seat forward or backward. Adjusting second row bucket seat back Pull control forward to adjust seat back. Using same control will fold the seat back flat. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Seating and Safety Restraints Note: Place the front row seat in a forward position to allow the 2nd row to be fully upright. Lift the handle located on the rear lower corner of the seat. The seat back will fold flat. Continuing to lift the handle will tumble the seat forward, allowing easier access to the third row seat. Note: Ensure the front row seat is in a forward position to allow the seat to return.
Seating and Safety Restraints After entering the 3rd row seat, return the seat from the tumbled position and latch it to the floor. Operate recline control to return the seatback to the upright position. Note: • Ensure that the seat and seatback is latched securely in position. • Keep floor area free of objects that would prevent proper seat engagement. • Do not adjust or release the seat floor latch while vehicle is in motion. • Do not operate the vehicle with seats in tumbled position.
Seating and Safety Restraints Removal of second row seats from vehicle 1. Place the front row seat in a forward position to allow the 2nd row seat to be fully upright. 2. Place the 2nd row seat in a rear position to allow the 2nd row seat to be fully upright. 3. Place seat in tumbled position. (See Accessing 3rd row seat) 4. From inside the vehicle, pull up on front floor release handle. 5. Rotate the seat rearward at a 30 to 45 degree angle.
Seating and Safety Restraints 6. With the assist handle, pull the seat rearward. 7. Remove the seat from vehicle. Installation of second row seats Prior to installation, ensure that the seats are on the correct side of the vehicle. Ensure that the seat is positioned so that the seat belt buckle is near the center aisle of the vehicle. The seatback must be folded flat prior to installation. 1. Position the seat in vehicle.
Seating and Safety Restraints 3. Rotate the seat forward until it latches onto the front pin. 4. Rotate seat rearward until the back of the seat latches onto the floor. 5. Operate recline lever and push the seat back upright. Ensure seat is latched to vehicle floor by pushing/pulling on seat. If not latched, the seat may cause injury during a sudden stop.
Seating and Safety Restraints Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or collision. Stowing the third row seat 1.
Seating and Safety Restraints 3. Store the tongue of the sliding latchplate in the belt pocket. 4. Store the belt in the housing found on the ceiling by inserting the smaller tongue in the slot provided. Note: The seat can be stowed with the safety belt connected if desired. Store the tongue of the sliding latchplate in the belt pocket to avoid potential damage to the seat. 5. Push the head restraint release buttons and move the head restraints fully down. Remove all objects from the seat and stowage tub.
Seating and Safety Restraints 6. From the rear of the vehicle, fold seat back by pulling and releasing the number 1 strap. Important: If you don’t let go of the number 1 strap before the seat back folds completely, the seat may not stow flat in the tub. Refer to the label attached to the rear of the vehicle seat.
Seating and Safety Restraints 7. Release the cushion latches by pulling the number 2 strap. 8. Pull the number 3 strap on the seat back to tumble seat all the way in to the tub in the floor. Do not use the seat anchors as cargo tie downs.
Seating and Safety Restraints Unstowing the third row seat Ensure seat latching area is free of objects. 1. Lift the seat out of the tub in the floor by pulling up on the exposed strap or handle. Once seat is at a vertical position, push the seat over, letting it fall onto the latches. 2. To return the seat back to the seating position, pull the number 1 strap, then while holding the number 1 strap, pull the number 3 strap to raise the seat back. 3.
Seating and Safety Restraints Third row seat features The seat is equipped with a recline function to allow for adjustment of the seat back for improved comfort. To activate the recliner, pull and hold the strap located near the plastic shield in the center of the seat. When seat is adjusted to desired location, release the strap. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Seating and Safety Restraints 2. To access the tailgate function, the seat must be in the seating position. If the seat is not in the seating position, follow all the steps of the ‘Unstowing Seat Section’. Once the seat is in the seating position, release the cushion latches by pulling the number 2 strap. Then, pull the seat rearward by the number 3 strap and set the seat on the liftgate scuff plate. The number 1 strap is not used to access this position. 2 Do not sit on the head restraints. 3.
Seating and Safety Restraints SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Seating and Safety Restraints common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Air bag supplemental restraints section in this chapter. Front crash severity sensor The front crash severity sensor enhances the ability to detect the severity of an impact. Positioned up front, it provides valuable information early in the crash event on the severity of the impact.
Seating and Safety Restraints The passenger occupant classification sensor can automatically turn off the passenger front air bag. The system is designed to help protect small (child size) occupants from air bag deployments when they are improperly seated or restrained in the front passenger seat contrary to proper child-seating or restraint usage recommendations. Even with this technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat.
Seating and Safety Restraints the RCM also monitors the restraints warning light in the instrument cluster. A difficulty with the system is indicated by one or more of the following. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and warning light are repaired.
Seating and Safety Restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.
Seating and Safety Restraints Energy Management Feature — Outboard • This vehicle has a safety belt system with an energy management feature at the front seats to help further reduce the risk of injury in the event of a head-on collision. • This safety belt system has a retractor assembly that is designed to extend the seat belt webbing in a controlled manner. This helps reduce the belt force acting on the user’s chest.
Seating and Safety Restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and Safety Restraints Unbuckle the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Safety belt height adjustment Your vehicle has safety belt height adjustments at the front and second row outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Seating and Safety Restraints The safety belt for the 3rd row center occupant may be stowed in the ceiling if it has been detached from the seat to carry large cargo. Remove the safety belt from the stowage area on the ceiling and buckle the small tongue on the end of the safety belt to the mini-buckle on the left side of the center seat position. The third row center lap/shoulder belt is equipped with a Belt Comfort Guide located in a pocket on the back of the seat.
Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON position... Then... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
Seating and Safety Restraints If... The driver’s and front passenger’s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The driver’s or front passenger’s safety belt is not buckled when the vehicle has reached at least 3 mph (5 km/h) and 1-2 minutes have elapsed since the ignition switch has been turned to ON...
Seating and Safety Restraints Reasons given... “Belts are uncomfortable” “I was in a hurry” “Safety belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” “I have an airbag” “I’d rather be thrown clear” Consider... We design our safety belts to enhance comfort. If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. Prime time for an accident.
Seating and Safety Restraints Do not sit on top of a buckled safety belt to avoid the BeltMinder娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the BeltMinder娂 feature please follow the directions stated below. One time disable If at any time the driver/front passenger quickly buckles then unbuckles the BeltMinder娂 feature for that seating position, the BeltMinder娂 is disabled for the current ignition cycle.
Seating and Safety Restraints 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt 9 times, ending in the unbuckled state. (Step 3 must be completed within 50 seconds after the safety belt warning light turns off.) • After Step 3, the restraint system warning light (airbag light) will be turned on for three seconds. 4. Within 10 seconds of the light turning on, at a moderate speed, buckle then unbuckle the safety belt.
Seating and Safety Restraints a collision. Ford recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced, except as described in the Replacing the front seat belt assemblies after a collision section of this chapter.
Seating and Safety Restraints outboard passenger from certain upper body injuries. The term “supplemental restraint” means the air bags are intended as a supplement to the safety belts. Air bags alone cannot protect as well as air bags plus safety belts in impacts for which the air bags are designed to deploy, and air bags do not offer any protection in crashes for which they do not deploy.
Seating and Safety Restraints To properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags). • side air bags (if equipped). Refer to Side air bag system later in this chapter.
Seating and Safety Restraints • the system determines that a small child is present in a forward-facing child restraint that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a booster seat, • a front passenger takes his/her weight off of the seat for a period of time, • A smaller person, such as a child who has outgrown child restraints, or a small adult occupies the front passenger seat.
Seating and Safety Restraints vehicle off and ask the person to place the seatback in the full upright position, then sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended. Restart the vehicle and have the person remain in this position for about two minutes. This will allow the system to detect that person and then enable the passenger’s air bag. If the indicator lamp remains lit even after this, then the occupant should be advised to ride in the back seat.
Seating and Safety Restraints In case there is a problem with the passenger sensing system, the airbag readiness light in the instrument cluster will stay lit. DO NOT attempt to repair or service the system; take your vehicle immediately to the dealer. If it is necessary to modify an advanced front air bag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide.
Seating and Safety Restraints Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side air bags and increase the risk of injury in an accident. Do not lean your head on the door. The side air bag could injure you as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the air bag SRS, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln/Mercury dealer.
Seating and Safety Restraints Side air bags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side air bags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the air bag on the side affected by the collision will be inflated, even if the respective seat is not occupied.
Seating and Safety Restraints Safety Canopy姟 system (if equipped) Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy娂. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not lean your head on the door. The Safety Canopy娂 could injure you as it deploys from the headliner.
Seating and Safety Restraints How does the Safety Canopy姟 system work? The design and development of the Safety Canopy娂 system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Air Bag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy娂).
Seating and Safety Restraints The Safety Canopy娂 is mounted to roof side-rail sheet metal, behind the headliner, along the entire side of the vehicle. In certain lateral collisions or rollover events, the Safety Canopy娂 system will be activated, regardless of which seats are occupied. The Safety Canopy娂 is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
Seating and Safety Restraints • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision or rollover event.
Seating and Safety Restraints Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
Seating and Safety Restraints Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’s head (top of ear level) above the top of the seat.
Seating and Safety Restraints Follow all instructions provided by the manufacturer of the booster seat. Never put the shoulder belt under a child’s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision.
Seating and Safety Restraints • LATCH lower anchors are recommended for use by children up to 48 pounds (22 kg) in a child restraint. Top tether anchors can be used for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster. Ford recommends the use of a child safety seat having a top tether strap.
Seating and Safety Restraints 1. Position the child safety seat in a seat with a combination lap and shoulder belt. If you use the 3rd row center seat and the safety belt has been detached from the seat to carry large cargo, remove the safety belt from the stowage area on the ceiling and buckle the small tongue on the end of the belt to the mini-buckle on the left side of the center seat position. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3.
Seating and Safety Restraints 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract.
Seating and Safety Restraints 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. To check this, grab the seat at the belt path and attempt to move it side to side and forward. There should be no more than one inch of movement for proper installation. 10.
Seating and Safety Restraints Front passenger seating position (manual adjusting seats only) 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. If the head restraint is adjustable, route the tether strap under the head restraint and between the head restraint posts. If the top of the safety seat hits the head restraint, raise the head restraint to let the child seat fit further rearward. 3.
Seating and Safety Restraints 4. Rotate the tether hook, and clip the tether strap to the seat frame. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. 5. Rotate the tether strap clip. 6. Install the child safety seat tightly using the LATCH anchors or safety belts. Follow the instructions in this chapter.
Seating and Safety Restraints 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Rear seating positions Follow Steps 1–7 as described above for the following available seats: • 2nd row bucket • 3rd row bench For additional important safety information on the proper use of safety belts, child seats and infant seats, please read the entire Seating and Safety Restraints chapter in this Owner’s Guide.
Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol. Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back.
Tires, Wheels and Loading INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Tires, Wheels and Loading The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Tires, Wheels and Loading • Extra load: A class of P-metric or Metric tires designed to carry a heavier maximum load at 41 psi [43 psi (2.9 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load carrying capability. • kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure.
Tires, Wheels and Loading Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove stones, nails, glass or other objects that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced.
Tires, Wheels and Loading higher than the manufacturer’s recommended cold inflation pressure which can be found on either the tire label or certification label which is located on the B-Pillar or the edge of the driver’s door. The cold inflation pressure should never be set lower than the recommended pressure on the tire label or certification label. When weather temperature changes occur, tire inflation pressures also change.
Tires, Wheels and Loading TIRE REPLACEMENT REQUIREMENTS Your vehicle is equipped with tires designed to provide a safe ride and handling capability. Only use replacement tires and wheels that are the same size and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford.
Tires, Wheels and Loading Temporary spare tire information Your vehicle may have a temporary spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. Replace this tire with a full-size tire as soon as possible. Note: The Low Tire Pressure Warning system (if equipped) will detect the temporary spare tire and illuminate the low tire warning light until the spare tire is replaced with a proper full-size tire.
Tires, Wheels and Loading Dissimilar spare tire/wheel information (if equipped) Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. Your vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels. If you have a dissimilar spare tire/wheel, then it is intended for temporary use only.
Tires, Wheels and Loading Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Item Spare tire Jack Jack handle Flat tire tether, wing screw Location Under the vehicle, just forward of the rear bumper. Behind the access panel located on the right rear quarter panel interior trim. Attached to the jack with a clip. Inside tire tether kit, next to jack. Removing the jack and tools 1. Locate the access panel on the interior trim.
Tires, Wheels and Loading 2. Turn the wrench counterclockwise until cable is slack and tire can be slid rearward. Item 1 2 3 Description Primary Tether Secondary Tether Anti-Rotation Tab 3. Remove the primary retainer from the center of the tire. 4. Stand tire up at the rear of the vehicle to access the lug nut for the secondary tether.
Tires, Wheels and Loading 5. Use the lug wrench provided to turn the lug nut counter clock wise to loosen, and remove the lug nut. 6. Lay the tire down and remove the secondary tether. Note: Do not stow the full size tire or any flat tire under the vehicle. Stowing the primary and secondary tether Note: If no tire is to be stowed under the vehicle, attach the secondary tether to the primary using the Velcro that’s attached to the secondary tether.
Tires, Wheels and Loading If the vehicle slips off the jack, you or someone else could be seriously injured. 1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine off, and block the diagonally opposite wheel. 3. Remove the spare tire, jack and lug wrench. 4. Removing the optional wheel cover or center ornament: • To remove a bolt-on wheel cover (if equipped) loosen the plastic nuts on the center ornament with the wheel nut wrench.
Tires, Wheels and Loading 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. If Ford Accessory Running Boards have been installed, use the jack adapters supplied with the running boards as described on the inside of the jack storage area. 6. Locate the jack notch next to the door closest to the tire you are changing, then place the jack on the frame rail directly behind the notch. 7.
Tires, Wheels and Loading To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall lug nuts until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 10.
Tires, Wheels and Loading 4. Check that the flat tire is properly secured. Stowing the spare tire Note: If no tire is to be stowed under the vehicle, attach the secondary tether to the primary using the Velcro that’s attached to the secondary tether. Wrap the Velcro around the primary cable and tightly back around the secondary, overlapping itself to secure. Note: Store secondary lug nut with the tether kit. 1. Lay the spare, inflated tire on the ground with the valve stem facing down. 2.
Tires, Wheels and Loading ratchet/slip occurs, if possible. The spare tire carrier will not allow you to overtighten. If the spare tire carrier ratchets or slips with little effort, take the vehicle to your dealer for assistance at your earliest convenience. 7. Check that the tire lies flat against the frame and is properly tightened. Try to push or pull, then turn the tire to be sure it will not move. Loosen and retighten, if necessary.
Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the Tire and Rim Association (T&RA), that may be used for service on cars, SUVs, minivans and light trucks.
Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186 mph (299 km/h) Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR.
Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (11⁄2) times as well on the government course as a tire graded 100. • Traction: The traction grades, from highest to lowest are AA, A, B, and C.
Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the Tire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/Load Inflation Limits: Indicates the tire’s load-carrying capabilities and its inflation limits. 3. Maximum Load Dual lb.
Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the Tire and Rim Association (T&RA), that is intended for temporary service on cars, SUVs, minivans and light trucks. 2.
Tires, Wheels and Loading TIRE CARE Improper or inadequate vehicle maintenance can also cause tires to wear abnormally. Here are some of the important maintenance items: Tire wear Measure and inspect the tire tread on all your tires periodically. Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy, etc.) conditions. Visually check your tires for uneven wear, looking for high and low areas or unusually smooth areas. Also check for signs of tire damage.
Tires, Wheels and Loading Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds.
Tires, Wheels and Loading The tires should also be balanced periodically. An unbalanced tire and wheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly, providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km).
Tires, Wheels and Loading • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar spare tire/wheel.
Tires, Wheels and Loading When a tire loses inflation, the low tire warning system detects the change and illuminates the low tire warning indicator light as shown. If the light remains on while driving, check the tire pressure refer to “Checking the tire pressure” in this chapter. The low tire warning indicator light will also illuminate when using a temporary spare, refer to “Changing the tires” in the Roadside emergencies chapter.
Tires, Wheels and Loading Speed ranges: • Low 25–42 mph (40–68 km/h) • Medium 42–62 mph (68–100 km/h) • High – above 62 mph (100 km/h) This system may not function properly under the following conditions: • Uneven tread wear. • Driving on loose or low traction surfaces such as gravel, snow or slush. • Using tire chains • Initial tire pressures out of specified range. • Two or more under inflated tires. • Sudden loss of tire pressure.
Tires, Wheels and Loading • These cable type chains should only be applied to the front wheels. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed.
Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door. Look for “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for maximum payload. The payload listed on the tire label is the maximum payload for the vehicle as built by the assembly plant.
Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight.
Tires, Wheels and Loading GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Tires, Wheels and Loading GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The GVW must never exceed the GVWR.
Tires, Wheels and Loading Maximum Loaded Trailer Weight – is the highest possible weight of a fully loaded trailer the vehicle can tow. It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your dealership (or the RV and Trailer Towing Guide provided by your dealership) for more detailed information.
Tires, Wheels and Loading 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. The following gives you a few examples on how to calculate the available amount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity. You decide to go golfing.
Tires, Wheels and Loading TRAILER TOWING Your vehicle is capable either of towing Class I trailers or up to Class II trailers when equipped with the optional trailer tow package. If your vehicle does not have the optional trailer tow package your vehicle is partially prepped for trailer tow lamp wiring but you will also need to install electrical kit 3F2Z-15A416-A.
Tires, Wheels and Loading Vehicle towing capability/Trailer hitch requirement Model/ Engine GCWR lb. (kg) Wagon, 4.2L 7200 (3266) Wagon, 4.2L with trailer tow option 8700 (3946) Trailer Trailer Weight range Tongue load - lb. (kg) Class I 0-2000 10 - 15% of TW Non-Equalizing (0-907) (200 lb. [91 kg] Weight maximum) Carrying 0–3500 10 - 15% of TW Class II Non-Equalizing (0-1588) (350 lb.
Tires, Wheels and Loading Safety chains Always connect the trailer’s safety chains to the hook retainers on the hitch. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Be sure your trailer conforms to all applicable local and Federal Regulations regarding trailer braking.
Tires, Wheels and Loading Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling. (For additional information, refer to the Understanding the positions of the 4–speed automatic transmission section in this chapter.
Tires, Wheels and Loading RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Front Wheel Drive (FWD) vehicles: It is not recommended to tow front wheel drive vehicles with the front drive wheels on the ground.
Driving STARTING Positions of the ignition 1. ACCESSORY, allows the electrical 4 accessories such as the radio to 3 operate while the engine is not 5 running. 2. LOCK, locks the steering wheel, 2 automatic transmission gearshift lever and allows key removal. 1 3. OFF, shuts off the engine and all accessories without locking the steering wheel. This position also allows the automatic transmission shift lever to be moved from the P (Park) position without the brake pedal being depressed.
Driving Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions.
Driving • Turn the key to 4 (ON) without turning the key to 5 (START). 4 3 5 2 1 Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter.
Driving 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. When the engine starts, release the key. 3 4 5 2 1 Note: If the engine does not start within five seconds on the first try, turn the key to 3 (OFF), wait 10 seconds and try again.
Driving BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by a qualified service technician. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by a qualified service technician. Refer to Brake system warning ! P light in the Instrument Cluster chapter for information on the brake BRAKE system warning light.
Driving Brake Assist (if equipped as part of the AdvanceTrac姞 system) The Brake Assist system provides full braking force during panic braking situations. It detects a rapid application of the brake pedal and maximizes the amount of brake booster assist, helping the driver to achieve maximum braking pressure. Once a panic brake application is detected, the system will remain activated as long as the brake pedal is depressed. The system is deactivated by releasing the brake pedal.
Driving vehicle does not respond to steering inputs, the system will attempt to increase the turning response of the vehicle. AdvanceTrac威 enhances your vehicle’s stability during maneuvers that require all available tire traction, like in wet/snowy/icy road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall vehicle traction, and have better control of the vehicle.
Driving ADVANCETRAC will show in the message center display. Have the vehicle system serviced immediately. If the vehicle is stuck in snow or mud or when driving in deep sand, switching off the AdvanceTrac威 system may be beneficial so the wheels are allowed to spin. If your vehicle seems to lose engine power while driving in deep sand or very deep snow, switching off the AdvanceTrac威 stability enhancement feature will restore full engine power and will enhance momentum through the obstacle.
Driving STEERING To prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (below the MIN mark on the reservoir). If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually, but it takes more effort.
Driving When the key is in the 3 (OFF) position, the automatic transmission shift lever can be moved from the P (Park) position without the brake pedal depressed. To avoid unwanted vehicle movement, always set the parking brake. 3. Start the vehicle. If it is necessary to use the above procedure to move the gearshift lever, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly. Refer to Fuses and relays in the Roadside Emergencies chapter.
Driving Understanding the gearshift positions of the 4–speed automatic transaxle P (Park) This position locks the transaxle and prevents the front wheels from turning. To put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever into the desired gear To put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Driving 1 (First) • Transaxle operates in first gear only. • Provides maximum engine braking. • Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle.
Driving FORWARD AND REVERSE SENSING SYSTEM The forward and reverse sensing system will warn the driver of obstacles within a certain range of the front and rear bumpers. The front sensors will be active when the gearshift is in any position other than P (Park) and the vehicle speed is below 8 mph (13 km/h). The rear sensors will only be active when the gearshift is in R (Reverse). The front sensors cover an area up to 31.
Driving The reverse sensing portion of the system detects obstacles up to 6 ft. (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the illustration for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away, the tone will sound continuously. If the system detects a stationary or receding object further than 10 inches (25.
Driving This system is not designed to prevent contact with small or moving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damaging the vehicle. The system may not detect smaller objects, particularly those close to the ground. Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the forward and reverse sensing system may create false beeps.
Driving The system is automatically enabled OFF when the gear selector is placed in D (Drive) or R (Reverse) and the ignition is ON. The park aid disable switch allows the driver to disable the system only when the ignition is ON, and the gear selector is in D (Drive) or R (Reverse). The OFF indicator remains illuminated when the system is disabled. If the indicator light illuminates when the system is enabled, it may indicate a failure in the RSS.
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 36,000 miles (60,000 km), whichever occurs first on Ford and Mercury vehicles, and four years or 50,000 miles (80,000 km) on Lincoln vehicles.
Roadside Emergencies Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Roadside Emergencies This switch is located behind the service panel on the right side of the cargo area. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. Turn the ignition ON. 5. Wait a few seconds and return the key to OFF. 6. Make another check for leaks. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies The fuses are coded as follows: Fuse/Relay Location 1 2 3 4 5 Fuse Amp Rating Relay Relay 10A 5A 20A 6 5A 7 8 10A 10A 9 10A 10 11 5A 5A 226 2005 Monterey (mty) Owners Guide (post-2002-fmt) USA_English (fus) Passenger Compartment Fuse Panel Description Accessory delay relay 1 Accessory delay relay 2 Front wiper motor Run feed B+ feed to outside mirrors Vent window power feed/Radio feed Driver door switch illumination/Passenger door switch illumination Rear wiper Run feed Clu
Roadside Emergencies Fuse/Relay Location 12 Fuse Amp Rating 5A 13 5A 14 5A 15 16 10A 5A 17 10A 18 10A 19 5A 20 10A 21 10A Passenger Compartment Fuse Panel Description Brake-Shift Interlock (BSI) Run feed, Climate control system Run feed Compass/Driver heated seat/Passenger heated seats/Reverse sensing system/Power Liftgate Module/Power sliding door Run feeds Underhood fuse box Run feed, Front blower Run feed Brake On-Off (BOO) switch B+ Steering angle/Cluster/Power sliding door and power l
Roadside Emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside Emergencies Fuse/Relay Location 4 5 6 Fuse Amp Rating 30A** 30A** 30A** 7 8 30A** 40A** 9 10 30A** 30A** 11 12 13 14 30A** 40A** 40A** 30A** 15 16 20 30A** 30A** Mini relay 21 22 23 24 25 26 27 28 29 30 31 32 Mini relay Micro relay Micro relay Mini relay Micro relay Micro relay — Mini relay Micro relay Micro relay Micro relay Mini relay Power Distribution Box Description Starter solenoid Right-hand power sliding door SJB accessory #2 (driver power window) Auxiliary blower motor Anti-loc
Roadside Emergencies Fuse/Relay Location 40 Fuse Amp Rating 15A* 41 42 43 25A* 10A* 15A* 44 45 46 47 48 49 50 51 10A* 15A* 20A* 15A* 15A* 10A* 10A* 10A* 52 53 54 55 56 57 58 20A* 10A* 30A* 25A* 30A* 20A* 30A* 59 60 20A* 30A* 230 2005 Monterey (mty) Owners Guide (post-2002-fmt) USA_English (fus) Power Distribution Box Description Engine #1 (A/C relay coil, IMRC, HEGO sensors, Canister purge, Transaxle, Canister vent) Horn A/C clutch Engine #2 (Cooling fan relays, Injectors, PCM, MAF sensor, IAC,
Roadside Emergencies Fuse/Relay Location 61 62 Fuse Amp Rating 20A* 30A* 63 20A* 64 65 20A* 30A* 66 20A* 67 20A* 70 — 71 — 72 — 73 — 74 — 75 Diode 76 Diode * Mini Fuse ** Cartridge Fuse Power Distribution Box Description Spare SJB #3 – Right cornering/auxiliary lamps, Right low beam, Left front park/turn lamps, Left rear park/stop/turn lamps, Instrument panel courtesy lamps, Step well lamps, Left signal mirror, Clock, Cluster, Message center (SJB F–15), Switch illumination for: overhead console, DVD/
Roadside Emergencies Auxiliary relay box (cooling fans) The relay box is located in the engine compartment by the radiator.
Roadside Emergencies Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start capability; doing so may damage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member of a roadside assistance program, your roadside assistance service provider. It is recommended that your vehicle be towed by wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Customer Assistance GETTING THE SERVICES YOU NEED At home You must take your Lincoln or Mercury vehicle to an authorized Lincoln Mercury dealer for warranty repairs. While any Ford or Lincoln Mercury dealership handling your vehicle line will provide warranty service, we recommend you return to your selling dealer who wants to ensure your continued satisfaction.
Customer Assistance In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Customer Assistance In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws.
Customer Assistance THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states.
Customer Assistance Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities.
Customer Assistance Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well.
Customer Assistance FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. It provides the following: • Benefits during the warranty period depending on the plan you purchase (such as: reimbursement for rentals; coverage for certain maintenance and wear items). • Protection against covered repair costs after your Bumper-to-Bumper Warranty expires.
Customer Assistance If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY WORLDWIDE DIRECT MARKET OPERATIONS 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A. Telephone: (313) 594-4857 FAX: (313) 390-0804 If you are in another foreign country, contact the nearest Ford dealership.
Customer Assistance REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight.
Cleaning • Do not allow paint sealant to come in contact with the sliding door electrical contact switches. Paint sealant or other contaminants could interfere with the proper operation of the power locks or power sliding door. If necessary, clean the contacts with Motorcraft Bug and Tar Remover (ZC-42) to remove any sealant. Do not use any abrasives on the contact surfaces. PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.
Cleaning • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts.
Cleaning • Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly. Do not use sharp objects, such as a razor blade, to clean the inside of the rear window or to remove decals, as it may cause damage to the rear window defroster’s heated grid lines.
Cleaning • Never saturate the seat covers with cleaning solution. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaning the seat-mounted side air bag.
Cleaning exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and Tar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26) Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide/Owner Information Guide to find out which parts and services are covered.
Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod. Your vehicle’s hood has two locations for the prop rod to be placed. These locations provide two different hood opening positions. Use the location which best suits your needs.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engines 10 9 2 1 8 7 6 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8. Windshield washer fluid reservoir 9. Engine coolant reservoir 10.
Maintenance and Specifications WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range.
Maintenance and Specifications • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by a qualified service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and Specifications Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricant Standardization and Approval Committee (ISLAC), comprised of U.S. and Japanese automobile manufacturers.
Maintenance and Specifications BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer toscheduled maintenance information for the service interval schedules. Keep the electrolyte level in each cell up to the “level indicator”. Do not overfill the battery cells.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications RN TU LE AD RE 7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more to relearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned.
Maintenance and Specifications • Freeze protection down to -34°F (-36°C). • Boiling protection up to 265°F (129°C). • Protection against rust and other forms of corrosion. • Enables calibrated gauges to work properly. When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Maintenance and Specifications Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolant and distilled water. Add the mixture to the coolant reservoir, when the engine is cool, until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts.
Maintenance and Specifications For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Add the proper mixture of coolant and water to the “FULL COLD” level.
Maintenance and Specifications Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recycling and disposing of automotive fluids.
Maintenance and Specifications • Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank.
Maintenance and Specifications • • • • swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.
Maintenance and Specifications • Keep sparks, flames and smoking materials away from fuel; • Stay outside your vehicle and do not leave the fuel pump unattended when refueling you vehicle — this is against the law in some places; • Keep children away from the fuel pump; never let children pump fuel Use the following guidelines to avoid static build-up when filling an ungrounded fuel container: • Place approved fuel container on the ground.
Maintenance and Specifications The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and Specifications Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems, try a different brand of unleaded gasoline. “Premium” unleaded gasoline is not recommended for vehicles designed to use “Regular” unleaded gasoline because it may cause these problems to become more pronounced. If the problems persist, see your dealer or a qualified service technician.
Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1,000 miles (1,600 km) of driving (engine break-in period).
Maintenance and Specifications Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5.
Maintenance and Specifications • You may want to turn off the speed control in hilly terrain if unnecessary shifting between third and fourth gear occurs. Unnecessary shifting of this type could result in reduced fuel economy. • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving.
Maintenance and Specifications It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of MPG (L/100 km) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and Specifications permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your Warranty Guide for complete emission warranty information.
Maintenance and Specifications If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic with at least four idle periods.
Maintenance and Specifications BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of your brake system could be compromised; seek service from your dealer immediately.
Maintenance and Specifications 7. Remove the dipstick and inspect the fluid level. The fluid should be in the designated areas for normal operating temperature. Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the outside temperatures are above 50°F (10°C). Correct fluid level The transmission fluid should be checked at normal operating temperatures 150°F-170°F (66°C-77°C) on a level surface.
Maintenance and Specifications Do not use supplemental transmission fluid additives, treatments or cleaning agents. The use of these materials may affect transmission operation and result in damage to internal transmission components. AIR FILTER MAINTENANCE Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter.
Maintenance and Specifications 2. Loosen the hose clamp located closest to the air cleaner. 3. Remove the air cleaner assembly from the vehicle. 4. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 5. Remove the air filter element from the air filter housing. 6. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.
Maintenance and Specifications 7. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. 8. Replace the air filter housing cover and secure the clamps. Be sure all the tabs on the bottom edge are properly aligned. 9. Reinstall the air cleaner assembly into the vehicle. Ensure the tabs on the inlet tube are secure in the sheet metal.
Maintenance and Specifications 10. Ensure the pads on the bottom of the air cleaner assembly are properly seated. 11. Reconnect the outlet tube to the air cleaner assembly and tighten the clamp. 12. Reconnect the Mass Air Flow Sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in “locked” position.
Maintenance and Specifications MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery Oil filter PCV valve Spark plugs 4.2L OHV V6 engine FA-1679 FG-986B BXT-59 BXT-65-750 FL-400S 1 2 1 The PCV valve is a critical emission component. It is one of the items listed in scheduled maintenance information and is essential to the life and performance of your vehicle and to its emissions system. For PCV valve replacement, see your dealer or a qualified service technician.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid Engine oil (includes filter change)3 Engine coolant Power steering fluid Fuel tank 2 Ford Part Name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid1 Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W-20 Super Premium Motor Oil (Canada) Motorcraft Premium Gold Engine Coolant (yellow-colored) Motorcraft MERCON威 ATF N/A Automatic transaxle fluid Application Capacity All Fill to MAX line on reserv
Maintenance and Specifications 3 Use of synthetic or synthetic blend motor oil is not mandatory. Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark.
Maintenance and Specifications Item Door latch, hood latch, auxiliary hood latch, door and liftgate hinges, striker plates, seat tracks, sliding door both sides (upper and lower track) and fuel filler door hinge.
Maintenance and Specifications 2 Ensure the correct automatic transmission fluid is used MERCON威 and MERCON威V are not interchangeable. DO NOT MIX MERCON威 and MERCON威V. Refer to scheduled maintenance information to determine the correct service interval. ENGINE DATA Engine Cubic inches Required fuel Firing order Ignition system Spark plug gap Compression ratio 4.2L OHV V6 engine 256 87 octane 1-4-2-5-3-6 EDIS 0.052–0.054 inch (1.32–1.42mm) 9.
Maintenance and Specifications 290 2005 Monterey (mty) Owners Guide (post-2002-fmt) USA_English (fus)
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the structure by the trailing edge of the driver’s door or the edge of the driver’s door.
Maintenance and Specifications 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and transfer case (if equipped).
Accessories MERCURY ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Mercury Accessories are available for your vehicle through your local authorized Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Rear seat entertainment systems - DVD Ash cup/coin holder Trailer hitches, wiring harnesses and accessories Peace of mind First aid and safety kits Full vehicle covers Locking gas cap Remote start Vehicle security systems Mobile-ease hands-free communication system For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight
Index A Accessory delay ..........................65 AdvanceTrac ..............................211 Air bag supplemental restraint system ................142–143, 149, 152 and child safety seats ............144 description ..............143, 149, 152 disposal ....................................155 driver air bag ..........145, 150, 153 indicator light .................149, 154 operation .................145, 150, 153 passenger air bag ...145, 150, 153 side air bag ..............................
Index wheels ......................................249 wiper blades ............................250 Clock ............................................63 Compass, electronic ....................55 calibration .................................57 set zone adjustment .................56 Console ........................................71 overhead ....................................55 Controls power seat ...............................110 steering column ........................71 Coolant checking and adding ...
Index Fluid capacities .........................286 Foglamps .....................................41 Fuel ............................................268 calculating fuel economy .......273 cap ...........................................270 capacity ...................................286 choosing the right fuel ...........271 comparisons with EPA fuel economy estimates .................275 detergent in fuel .....................272 filling your vehicle with fuel ...........................
Index bulb replacement specifications chart ..................48 daytime running light ...............42 fog lamps ...................................41 headlamps .................................41 headlamps, flash to pass ..........43 instrument panel, dimming .....44 interior lamps .....................46–48 replacing bulbs ...................48–52 Lane change indicator (see Turn signal) ........................46 Liftgate ............................85, 89, 96 Lights, warning and indicator ....
Index illuminated entry ................43, 99 locking/unlocking doors .....91, 95 Roadside assistance ..................222 Roof rack .....................................89 S Safety Belt Maintenance ..........141 Safety belts (see Safety restraints) ..................128, 131–135 Safety Canopy ...........................152 Safety defects, reporting ..........247 Safety restraints ........128, 131–135 belt minder .............................137 extension assembly ................141 for adults ..........
Index Transmission brake-shift interlock (BSI) ....214 fluid, checking and adding (automatic) .............................279 lubricant specifications ..........287 Turn signal ..................................46 V Vehicle dimensions ...................289 Vehicle Identification Number (VIN) ..........................................291 Vehicle loading ..........................194 Ventilating your vehicle ...........
