Table of Contents Introduction Instrument Cluster 4 10 Warning and control lights Gauges 10 16 Entertainment Systems 19 AM/FM stereo cassette with CD AM/FM stereo with CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 19 34 44 44 47 47 50 51 57 57 59 60 60 61 66 1
Table of Contents Locks and Security 70 Keys Locks Anti-theft system 70 70 71 Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires Jump starting Wrecker towing 2 79 79 83 94 102 112 112 116 119 120 129 130 134 134 135 135 136 142 145 151
Table of Contents Customer Assistance Reporting safety defects (U.S. only) 152 160 Cleaning 161 Maintenance and Specifications 167 Engine compartment Engine oil Battery Fuel information Part numbers Refill capacities Lubricant specifications 170 172 175 182 198 199 200 Accessories 204 Index 207 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction Fuel pump shut-off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.
Introduction Protecting the environment We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol. BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. During the first 1,600 km (1,000 miles) of driving, vary speeds frequently.
Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. By operating other electronic equipment (e.g. mobile telephone without exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics. Therefore you should observe the instructions of the equipment manufacturers. Please read the section Air bag in the Seating and safety restraints chapter.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Power Window Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine Air Filter Passenger Compartment Air Filter Jack Check fuel cap Low tire warning 9
Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.
Instrument Cluster If the light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Instrument Cluster Safety belt Illuminates to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Air bag readiness Illuminates to confirm that the air bags (front and side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Charging system Illuminates when the battery is not charging properly.
Instrument Cluster Traction ControlY active Illuminates when the Traction Controly system is active. It will be lit for a minimum of four seconds or for the duration of the Traction Controly event. For more information, refer to the Driving chapter. Low fuel Illuminates when the fuel level in the fuel tank is at, or near, empty (refer to Fuel gauge in this chapter for more information).
Instrument Cluster High beams Illuminates when the high beam headlamps are turned on. Foglamps Illuminates when the foglamps are turned on. Refer to Foglamp control in the Lights chapter. OVERHEAD WARNING LIGHTS (if equipped) These lights illuminate briefly to ensure the systems are functional. Service intervals Illuminates to indicate that routine service should be performed. Check your maintenance schedule to determine the routine service to be completed.
Instrument Cluster Danger of ice warning Illuminates when ambient air temperature is 0° C (32° F) and below. The red light warns of an increased danger of icy roads. The absence of a light in cold temperatures does not necessarily mean that there is no risk of ice on the road. Low washer fluid Illuminates when the windshield washer fluid is low. Door ajar Illuminates when any door or liftgate is open. Safety belt warning chime Sounds to remind you to fasten your safety belts.
Instrument Cluster Key-in-ignition warning chime Sounds when the key is left in the ignition and the driver’s door is opened. Liftgate ajar warning chime (if equipped) Sounds when the liftgate is ajar or open and the key is in the ignition. The interior dome lamp will also be illuminated. GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant.
Instrument Cluster Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade. When refueling the vehicle from an empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle.
Instrument Cluster Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the SELECT control on the trip computer. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Entertainment Systems PREMIUM AM/FM STEREO/CD SYSTEM BASS/TREB FADE/BAL CD AM/FM VOL ON/OFF MENU SCAN SEEK CLK 1 2 3 4 5 6 Anti-theft protection panel To deter would-be thieves, Ford audio units have a removable front panel without which the unit will not work. Avoid touching the contacts on the back of the panel and do not use excessive force to refit it. Slide the security release button to the left and remove the front panel.
Entertainment Systems 3. The audio unit type. 4. Proof of identification (driver’s license, identity card, etc.). 5. A vehicle invoice (if the audio unit was installed in the vehicle prior to delivery) or a parts invoice if the audio unit was purchased separately form the vehicle, or an appropriate vehicle registration document. Volume/power control Press the control to turn the audio system on or off. VOL ON/OFF Turn the control to raise or lower volume.
Entertainment Systems AM/FM select The AM/FM select control works in CD AM/FM radio and CD modes. To gain the best reception, always tune to the strongest station signal available. Under most conditions, the AM frequency provides stable sound quality and little signal disturbance. However, at night, atmospheric conditions may sometimes lead to interference from other stations.
Entertainment Systems Seek function The seek function works in radio and CD modes. Seek function in radio mode • Press to find the next listenable station down the frequency band. SEEK DOWN will display. SEEK • Press to find the next listenable station up the frequency band. SEEK UP will display. Seek function in CD mode (fast forward and reverse track selection) • Press to return to the beginning of the current track.
Entertainment Systems Turn the volume control (VOL) up or down to the desired setting. Bass adjust The bass adjust control allows you BASS/TREB FADE/BAL to increase or decrease the audio system’s bass output. Press the BASS/ TREB control until BASS appears in the display. Turn the volume control (VOL) up or down to the desired setting. Speaker fade adjust (if equipped) Speaker sound can be adjusted BASS/TREB FADE/BAL between the front and rear speakers.
Entertainment Systems Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations, twelve FM stations (six in FM1 and six in FM2) and six on the remaining AutoStore band. Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3.
Entertainment Systems Press CD to start playback from a CD already in the audio unit. If no disc is inserted, NO CD appears in the display. The display indicates elapsed track time up to 19:59. If the track is longer than twenty minutes, the first digit flashes while the rest of the numeral returns to zero and starts counting again. This audio unit is designed to play commercially pressed 12cm audio compact discs only.
Entertainment Systems Press the SEEK control to turn the feature ON or OFF. SEEK Menu mode Press the MENU control to access main menu features. Use the SEEK control for adjustments. MENU CD eject function Press the eject control during CD playback to eject the CD. Setting the clock Your vehicle is equipped with a separate instrument panel mounted clock. Please refer to Clock in the Driver controls chapter for instructions on setting the clock.
Entertainment Systems Volume/power control Press the control to turn the audio system on or off. Audio power can also be turned on by pressing the AM/FM select control or the TAPE/CD select control. VOL - PUSH ON Turn control to raise or lower volume. VOL - PUSH ON AM/FM select The AM/FM select control works in radio, tape and CD modes. AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Entertainment Systems • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer. (Play will begin on the first track of the disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the remaining discs. to select the next disc in the CD changer.
Entertainment Systems Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’s first side, direction automatically reverses to the opposite side of the tape.) To stop on a particular selection, press the control again. Scan function in CD or CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD.
Entertainment Systems Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the control. 3. When the first six strong stations AUTO are filled, the station stored in memory preset control 1 will start playing. CLK If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • • BAL BAL FADE FADE to shift the sound to the front and to shift the sound to the rear.
Entertainment Systems into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information. Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached.
Entertainment Systems DolbyT noise reduction Dolbyt noise reduction operates in tape mode. Dolbyt noise reduction reduces the amount of hiss and static during tape playback. Press the reduction. 4 control to activate (and deactivate) the Dolbyt noise Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation. “Dolbyt” and the double-D are registered trademarks of Dolbyt Laboratories Licensing symbol Corporation.
Entertainment Systems Mute mode Press the MUTE control to mute the playing media. Press the MUTE control again to return to the playing media. EJ MUTE PREMIUM AM/FM STEREO IN DASH SIX CD RADIO SHUF DISC TUNE SCAN SEEK REW COMP FF MUTE EJ LOAD BASS BAL SEL TREB FADE PUSH ON AM FM CD 1 2 3 4 5 6 Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume.
Entertainment Systems AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radio play. Tune/disc adjust The tune control works in radio or CD mode. Tune adjust in radio mode • Press to move to the next DISC TUNE frequency down the band (whether or not a listenable station is located there).
Entertainment Systems Seek function in CD mode • Press to seek to the previous track of the current disc. If the beginning of the disc is reached, the CD player seeks to the beginning of the last track on the current disc and begins playing. • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio or CD mode.
Entertainment Systems the control you selected. The display will read SAVED. Autostore Autostore allows you to set the strongest local radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autostore 1. Press and momentarily hold the AM/FM control. 2. AUTOSET will flash in the display AM CD as the frequency band is scrolled FM through. 3.
Entertainment Systems CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Entertainment Systems loaded into position and the audio system will display CD#. Each time the CD door opens, INSERT CD# is displayed. The door will close and the player will move to the next slot after each disc has been loaded. The process is repeated until all 6 slots are full. The audio system plays the last CD loaded and the display is updated. If some slots are already full and autoload is activated, the system will fill all empty slots. Eject Press the EJ control to stop and EJ eject a CD.
Entertainment Systems Press and hold the FF control until the desired selection is reached. If the end of the disc is reached, the CD will return to the first track. Release the control to disengage fast forward mode. When in fast forward mode, your audio system will automatically lower the volume level of the playing media. Shuffle feature Press the SHUF control until the desired shuffle mode is displayed. The audio system will then engage the desired shuffle mode.
Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control. Use the SEL control to adjust the sound between the left and right speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control. Use the SEL control to adjust the sound between the front and rear speakers. BAL + SEL + SEL FADE BAL FADE Mute mode Press the control to mute the playing media.
Entertainment Systems CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed.
Entertainment Systems RADIO RECEPTION FACTORS Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations. • Terrain.
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. • MAX A/C – Distributes recirculated air through the instrument panel registers. The A/C compressor will only function if the outside temperature is above approximately 6°C (43°F).
Climate Controls • O (Off) – Outside air is shut out and the fan will not operate. This mode may reduce undesirable odors from entering the vehicle but may increase the possibility of interior window fogging. • (Floor) – Distributes outside air through the floor ducts. The air cannot be cooled below the outside temperature. • (Floor and defrost) – Distributes outside air through the windshield defroster ducts and the floor duct and the side window demisters.
Climate Controls • Do not place objects under the front seat or over the defroster ducts. They may reduce visibility, fall into the ducts, or degrade the performance of your climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog.
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on when the headlamp or control is in the the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp will illuminate.
Lights High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during parklamp, headlamp, and autolamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate fully up to turn on the interior lights.
Lights AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been aimed in an accident the alignment of your headlamps should be checked by a qualified service technician. Each headlmap may be properly aimed in the vertical (up/down) direction only. THE HORIZONTAL (left/right) AIM IS PRESET BY THE HEADLAMP MANUFACTURER AND DOES NOT NEED TO BE RE-AIMED. Adjusting the vertical aim 1. Park the vehicle on a level surface. 2.
Lights TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. • In vehicles equipped with daytime running lights, use of the turn signals will shut off the highbeams in daytime driving. INTERIOR LAMPS The interior lamps have three switch positions: door delay, off and on. When the control is switched to door delay, the interior light stays on for 12 seconds after the doors are closed with the ignition off.
Lights BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: • Headlamps • Tail lamps • Brakelamps • High-mount brakelamp • Turn signal lamps • Backup lamps • License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Using the right bulbs Replacement bulbs are specified in the chart below.
Lights Replacing headlamp bulbs Make sure the headlamp switch is in the OFF position. To remove the high or low beam headlamp bulb: 1. Lift the hood and release the wire clip on the rear of the headlamp assembly and remove the cover. 2. Disconnect the electrical connector by turning the bulb holder counterclockwise. 3. Pull the bulb holder straight out to remove the bulb. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Lights 2. Connect the electrical connector to the bulb. 3. Install the protective cover and secure it with the wire clips. 4. Turn the headlamps on and make sure they work properly. if the headlamp was correctly aligned before you changed the bulb, you need to align it again. Replacing front parking lamp/turn signal bulbs 1. Remove the headlamp assembly cover. 2. Turn the bulb holder counter clockwise. 3. Remove the bulb socket by pulling it straight out from the lamp assembly. 4.
Lights 1. From the trunk, remove the carpet cover from the lamp assembly. 2. Remove the three retainer nuts and pull the lamp assembly out. 3. Turn the bulb counterclockwise and pull it out. 4. Replace the defective bulb. 5. Replace the lamp assembly and turn it clockwise to secure it in place. Replacing the rear parking lamps 1. From the trunk, locate the parking lamp on the trunk wall near the tail lamp. 2. Turn the bulb socket counterclockwise and pull it out. 3.
Lights Replacing high-mount brake lamp bulbs 1. Remove the push pins and cover from the liftgate. (To remove the push pins, press the two tabs of the push pin insert inward and pull the insert out.) 2. Turn the bulb socket counterclockwise. 3. Pull the bulb straight out of the socket and push in the new bulb. To install the lamp assembly: 1. Install the bulb into the lamp assembly and turn it clockwise 2. Replace the cover and the push pins. Replacing the luggage compartment lamp 1.
Lights Replacing interior lamps 1. Switch off the interior lamps (middle switch position). 2. Open the lamp assembly. 3. Release the reflector at the side. 4. Pull out and replace the bulb. Replacing reading bulbs (if equipped) 1. Open the reading lamp assembly. 2. Pull the bulb straight out and replace it. 3. After the bulb has been replaced, close the lamp assembly.
Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Lift the windshield wiper control to the desired interval. • Intermittent: push lever up to the first position. • Low: push lever up to the second position. • High: push lever up to the third position. For a single wipe, push the lever downward. Intermittent wiper control Rotate the variable intermittent wiper control to the desired speed. • 1 = Short time interval • 6 = Extended time interval Washer Pull the lever toward the steering wheel.
Driver Controls WINDSHIELD WIPER BLADES Check the wiper blades for wear at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades. CHECKING WIPER BLADES Check the wiper blades on your vehicle for roughness by running the tip of your fingers over the edge of the blade. Traces of grease, silicone and fuel also prevent wiper blades from functioning properly.
Driver Controls TILT STEERING WHEEL Pull the locking lever on the steering column cover up to adjust the steering column position. Secure the wheel by releasing the locking lever. Never adjust the steering wheel when the vehicle is moving. HORN Press the pad in the middle of the steering wheel.
Driver Controls CLOCK The clock can be set to either a 12 hour or a 24 hour format. Press the CLOCK button until it flashes. Press the UNITS button once to display 12HR. Press the RESET button to toggle between 12 and 24 HR. Press the UNITS button until the hour flashes. Press the RESET button to set the hour. Press the UNITS button until the minutes flash. Press the RESET button to set the minutes. Press the CLOCK button to store the time.
Driver Controls 1. The control can be swiveled and turned. Turn the control clockwise to adjust the driver’s side mirror, counterclockwise to adjust the passenger side mirror. 2. Adjust the selected mirror by moving the center control in the desired direction. Then turn the control back to the center position. Heated mirrors (if equipped) The heated mirrors are activated by turning on the rear window defroster. SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON.
Driver Controls Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press + and release. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Driver Controls If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing = will re-engage it. Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. To set a higher set speed • Press and hold +. Release the control when the desired vehicle speed is reached or • Press and release + to operate the Tap-Up function. Each press will increase the set speed by 1.
Driver Controls To set a lower set speed • Press and hold −. Release the control when the desired speed is reached or • Press and release − to operate the Tap-Down function. Each press will decrease the set speed by 1.6 km/h (1 mph) or • Depress the brake pedal. When the desired vehicle speed is reached, press +. To disengage speed control • depress the brake pedal, or Disengaging the speed control will not erase the previously programmed set speed. • Press the OFF control.
Driver Controls To return to a previously set speed • Press =. For = to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when the vehicle speed control is engaged and actively controlling vehicle speed. MOON ROOF (IF EQUIPPED) To lift the rear of the moon roof: moon roof control • Press the to lift up. • Press and hold (as desired) the bottom moon roof control to close. To open and close the moon roof: • Press and hold the moon roof control to open.
Driver Controls TRIP COMPUTER The trip computer tells you about the condition of your vehicle through a constant monitor of vehicle systems. You may select display features on the trip computer for a display of status. The trip computer only operates with the ignition in the ON position.
Driver Controls Distance to empty This displays the approximate distance you can drive with the fuel remaining in the tank. Average fuel economy Shows the average fuel economy since last reset. TRUNK REMOTE CONTROL Push the control located under the instrument panel by the driver’s door to open the luggage compartment. FRONT ASHTRAY The ashtray is located beneath the radio. To open, press and the ashtray opens automatically. To empty, extract the ashtray.
Driver Controls POSITIVE RETENTION FLOOR MAT (DRIVER’S SIDE ONLY) Position the floor mat in the footwell. Place the mat eyelet over the pointed end of the retention post from the rear and rotate forward to install. Adjust the floor mat position to allow proper operation of accelerator pedal, brake pedal and clutch pedal (if equipped). To remove, lift the floor mat just forward of the retention post and rotate it rearward to disengage it from the retention post.
Driver Controls To install the cover: Insert the cover horizontally, align it and push in as far as the stop. Attach the lifting straps to the liftgate. Do not place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. The cover may cause injury in a sudden stop or accident if it is not securely installed. USING A LUGGAGE RACK The moon roof opens to the outside.
Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to SecuriLocky Passive Anti-Theft System for more information. POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors.
Locks and Security To open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light. The “T” shaped handle will be located either on the luggage compartment door (lid) or inside the luggage compartment near the tail lamps.
Locks and Security Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The remote entry system allows you to lock or unlock all vehicle doors and luggage compartment without a key. The remote entry features only operate with the ignition in the OFF position.
Locks and Security Opening the luggage compartment Press this control to open the luggage compartment. Be certain the luggage compartment is closed before driving your vehicle. The luggage compartment may appear closed, but it may not be latched. Failure to do so may cause objects to fall out of the luggage compartment or block rear view vision. Sounding a panic alarm Press this control to activate the alarm. The horn will sound and the lights will flash for approximately two minutes.
Locks and Security 1. Twist a thin coin between the two halves of the transmitter. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new batteries down. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together.
Locks and Security If a problem occurs with the SecuriLocky system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If this occurs, the vehicle should be taken to an authorized dealer for service. Automatic arming The vehicle is armed five seconds after switching off the ignition. The indicator light on the dashboard above the climate controls will flash every two seconds when the vehicle is armed.
Locks and Security • A second key on the same key ring as the coded key If any of these items are present, you need to keep these objects from touching the coded key while starting the engine. These objects and devices cannot damage the coded key, but can cause a momentary “no start” condition if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key.
Locks and Security 1. Insert the first previously programmed coded key into the ignition switch and turn to position No. 3. 2. Turn the key back to position No. 1 and remove from the ignition within 5 seconds. 3. Insert the second previously programmed coded key into the ignition switch and turn to position No. 3 within 3–5 seconds. 4. Turn the key back to position No. 1 and remove from the ignition within 5 seconds, the key coding mode is now activated. 5.
Locks and Security Activation The system is activated by pressing the control once. The ignition key must be removed from the ignition and the doors, hood and luggage compartment fully closed, to allow activation. The lamps will flash once to indicate the system is activated. If the lamps do not flash once, the system is not activated. Arming the system Opening any door, hood, or luggage compartment will activate the alarm when activated.
Seating and Safety Restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Pull the lever located under the front edge of the seat to move the seat forward or backward. To recline the seat, pull the lever on the outside of the seat.
Seating and Safety Restraints To lean the seatback forward, pull the lever on the outside of the seatback. Fold back the seatback until it locks with a distinct “click” and slide the seat backwards until it locks in position. Rock the seat to ensure that the catch is securely engaged. Adjusting the power seats (if equipped) To adjust the height of the seat, push the control up or down. The control is located on the left front corner of the seat.
Seating and Safety Restraints To adjust the power seat, move the control located on the left front corner of the seat. Move the control in the respective direction to adjust the seat, seat back and lumbar as follows: 1. Move the seat forward and backward 2. Adjust the height of the entire seat 3. Incline or recline the seatback 4.
Seating and Safety Restraints To raise the rear seatback, push the seatback upward until it locks in place. Make sure it is firmly latched by pushing forward and back on it. Check to see that the seat and seatback are latched securely in position. Keep luggage area of objects that would prevent proper engagement. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and Safety Restraints In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision.
Seating and Safety Restraints Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1. Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2. Never swing the safety belt around your neck over the inside shoulder. 3. Never use a single belt for more than one person.
Seating and Safety Restraints Automatic locking mode How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
Seating and Safety Restraints When to use the automatic locking mode • When a tight lap and shoulder belt fit is desired. • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.
Seating and Safety Restraints Front safety belt height adjustment To lower the height of the shoulder belt: 4. Push the release control lever down. 5. Slide the seat belt loop down. To raise the height of the shoulder belt: 1. Slide the seat belt loop upwards. 2. Pull down on the seat belt loop to make sure that it is locked in place. Position the safety belt height adjusters so that the belt rests across the middle of your shoulder.
Seating and Safety Restraints BeltMinder The BeltMinder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver’s safety belt is unbuckled by intermittently sounding a chime and illuminating the safety belt warning lamp in the instrument cluster once the vehicle speed has exceeded 5 km/h (3mph). If... The driver’s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off...
Seating and Safety Restraints Reasons given... “Crashes are rare events” “I’m not going far” “Belts are uncomfortable” “I was in a hurry” “Seat belts don’t work” “Traffic is light” “Belts wrinkle my clothes” “The people I’m with don’t wear belts” 90 Consider... 36 700 crashes occur every day. The more we drive, the more we are exposed to “rare” events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lifetime. 3 of 4 fatal crashes occur within 25 miles of home.
Seating and Safety Restraints Reasons given... “I have an air bag” “I’d rather be thrown clear” Consider... Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. Do not sit on top of a buckled safety belt to avoid the Belt Minder chime.
Seating and Safety Restraints BeltMinder activation and deactivation procedure 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation. 4.
Seating and Safety Restraints Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8 inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and Safety Restraints Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Cleaning chapter. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Seating and Safety Restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is greatest close to the trim covering the air bag module.
Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may affect the performance of the air bag sensors increasing the risk of injury. Do not modify the front end of the vehicle.
Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation.
Seating and Safety Restraints The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags) • one or more impact and safing sensors • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and t
Seating and Safety Restraints Side air bag system (if equipped) Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision. Do not use accessory seat covers.
Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag SRS, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle should always wear their safety belts even when an air bag SRS is provided.
Seating and Safety Restraints The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. Side air bags are designed to inflate in side-impact collisions, not roll-over, rear-impact, frontal or near-frontal collisions, unless the collision causes sufficient lateral deceleration. Several air bag system components get hot after inflation. Do not touch them after inflation.
Seating and Safety Restraints A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front air bag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision.
Seating and Safety Restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle.
Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).
Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs. The shoulder belt should cross the chest, resting snugly on the center of the shoulder.
Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Rear-facing child seats or infant carriers should never be placed in the front seats. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety properly, the child may be injured in a sudden stop or collision. Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
Seating and Safety Restraints The best fit can be obtained with a child safety seat that has a base wide enough to span the depression of the rear seat so that it rests on the highest part of the seat cushion. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and Safety Restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps in this chapter. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle.
Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8.
Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Driving STARTING Positions of the ignition 1. LOCK, locks the steering wheel, gearshift lever (automatic transaxle only) and allows key removal. On vehicles with a manual transaxle push the key in while turning to lock. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts.
Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs faster to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked. Do not allow the vehicle to idle for more than 10 minutes at the higher RPM.
Driving If starting a vehicle with a manual transaxle: • Push the clutch pedal to the floor, put the gearshift in neutral. 4. Turn the key to 3 (ON) without turning the key to 4 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns freely.
Driving • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3 (ON). 2.
Driving Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Have the exhaust and body ventilation systems checked whenever: • the vehicle is raised for service.
Driving road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat and become less effective.
Driving With the ABS light on, the anti-lock P ! brake system is disabled and normal braking is still effective unless the brake warning light also remains BRAKE illuminated with parking brake released. (If your brake warning lamp illuminates, have your vehicle serviced immediately.) Using ABS • In an emergency or when maximum efficiency from the four-wheel ABS is required, apply continuous force on the brake.
Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transaxle) or in 1 (First) (manual transaxle). Push the button on the end of the parking brake and push the handle down as far as possible to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. TRACTION CONTROLY Your vehicle is equipped with a Traction Controly system.
Driving The Traction Controly on/off switch, located in the center of the instrument panel illuminates when the system is OFF. The Traction Controly system will revert to the ON position every time the ignition is turned OFF and ON. If you should become stuck in snow or ice or on a very slippery road surface, try switching the Traction Controly system off. This may allow excess wheel spin to “dig” the vehicle out and enable a successful “rocking” maneuver.
Driving 1. Turn the ignition off and remove the key. 2. Apply the parking brake and the brake pedal. 3. Insert a screwdriver or similar item about 5 cm (2 inches) into the square opening to the right of the gearshift at the base of the console. On vehicles without the opening, insert a screwdriver or similar item about 5 cm (2 inches) inward, directly below the arrow symbol located to the right of the gearshift at the base of the console. 4. Rotate the screwdriver point rearward. 5.
Driving The console-mounted gearshift will lock when you turn the key to the LOCK position. When the gearshift is in any position except P (Park), the ignition key cannot be turned to LOCK or removed from the steering column. To remove the key, the gearshift lever must be in P (Park). Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary.
Driving N (Neutral) With the gearshift lever in the N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) The normal driving position for the best fuel economy. Transaxle operates in gears one through four. (Overdrive) can be deactivated by pressing the transaxle control switch (TCS) on the underside of the gearshift handle. The transaxle control indicator light (TCIL) (O/D OFF) in the instrument cluster will illuminate.
Driving Drive – Not shown on the display. Activate by pressing the transaxle control switch (TCS) on the underside of the gearshift handle with the gearshift in the position. The TCIL (O/D OFF) will illuminate in the instrument cluster. Transaxle operates in gears one through three. (Drive) provides more engine braking than (Overdrive) and is useful when: • driving with a heavy load. • towing a trailer up or down steep hills. • additional engine downhill braking is desired.
Driving 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transaxle to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Forced Downshifts To gain acceleration in (Overdrive) or Drive (O/D OFF) when passing another vehicle, push the accelerator to the floor.
Driving When starting a vehicle with a manual transaxle: 1. Hold down the brake pedal and clutch pedal. 2. Put the gearshift lever in neutral. 3. Start the vehicle. 4. Put the gearshift lever in 1 (First) or R (Reverse). 5. Release the clutch slowly while pressing gradually down on the accelerator pedal. Do not drive with your foot resting on the clutch pedal and do not use the clutch pedal to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life.
Driving 2.5L engine 5–speed transaxle shift speed schedules Recommended During acceleration: During cruise*: upshifts: Shift from: km/h mph km/h mph First to second 22 14 16 10 Second to third 40 25 32 20 Third to fourth 53 33 50 31 Fourth to fifth 77 48 64 40 *The vehicle can be shifted at lower speeds to improve fuel economy. Parking 1. 2. 3. 4. Apply the brake and shift into the neutral position. Engage the parking brake. Shift into 1 (First). Turn ignition off.
Driving 3. Push the gearshift lever completely to the right, pull up the ring on the stalk of the gearshift lever, and then pull rearward on the gearshift lever to engage the R (Reverse) gear. 4. When the R (Reverse) gear is engaged, slowly release the clutch pedal from the floor. DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall.
Driving VEHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb Weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include occupants or aftermarket equipment. • Payload: Combined maximum allowable weight of cargo, occupants and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus payload weight.
Driving Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations. The Safety Certification Label, found on the driver’s door pillar, lists several important vehicle weight rating limitations.
Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch. You must distribute the load in your trailer so that 10% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the frame or hook retainers of the vehicle hitch.
Driving Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transaxle cooling. • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transaxle damage may occur.
Driving RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication. All Front Wheel Drive (FWD) vehicles: An example of recreational towing is towing your vehicle behind a motorhome.
Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited Warranty period of three years or 60,000 km (36,000 miles), whichever occurs first on Ford and Mercury vehicles, and four years or 80,000 km (50,000 miles) on Lincoln vehicles.
Roadside Emergencies If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadian customers who need to obtain reimbursement information, call 1–800–665–2006.
Roadside Emergencies The fuel pump shut-off switch is located in the driver’s foot well, behind the kick panel. The reset button for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the RUN position.
Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses 2A 3A 4A 5A 7.
Roadside Emergencies The fuses are coded as follows: 138 Fuse/Relay Location 19 20* 21 22 23 Fuse Amp Rating 7.5A 10A 40A 7.5A 15A 24 25 26 27 28 29 15A 20A 7.5A 15A 30A 30A Passenger Compartment Fuse Panel Description Mirror heater Wipers Power moonroof, Power windows ABS/TCS Turn signal lamps, Backup lamps, Speed control.
Roadside Emergencies Fuse/Relay Location 30 Fuse Amp Rating 7.5A 31 7.5A 32 33 34 — 7.5A 7.5A 35 7.5A 36 15A 37 30A 38 7.
Roadside Emergencies The high-current fuses are coded as follows.
Roadside Emergencies Fuse/Relay Location 12 13 14 15 16 17 18 Fuse Amp Rating — 20A — 7.5A 7.5A 7.5A 7.
Roadside Emergencies Fuse/Relay Location R8 R9 R10 R11 Fuse Amp Rating — — — — Power Distribution Box Description High speed engine cooling fan Engine cooling fan Not used Daytime running lamps (Canada only) D1 — Starter relay D2 — Air conditioning * Have these fuses replaced by your dealer or qualified technician. CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Roadside Emergencies • try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Use of a temporary spare tire at any one wheel location can lead to impairment of the following: • handling, stability and braking performance • comfort and noise • ground clearance and parking at curbs • Winter driving capability Tire change procedure 1. Park on a level surface, activate hazard flashers and set the parking brake.
Roadside Emergencies • Automatic • Manual 3. Remove the jack, jack handle, lug wrench and spare tire.
Roadside Emergencies 4. Insert the tapered end of the jack handle beneath the hub cover (if equipped) and push in. Twist off to remove the cover. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Place the jack under vehicle in location indicated by arrows (closest to the tire requiring changing), then jack up the vehicle until the tire is clear of the ground. 6. Remove the lug nuts with the lug wrench. 7.
Roadside Emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2.
Roadside Emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Roadside Emergencies + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5.
Roadside Emergencies Removing the jumper cables + + – – Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery.
Roadside Emergencies + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Roadside Emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure.
Customer Assistance GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. It is preferred that you return to the Ford dealer where your vehicle was purchased when warranty repairs are needed. However, you may also take your vehicle to another Ford Motor Company or Ford of Canada dealership authorized for warranty repairs.
Customer Assistance Ford Motor Company of Canada, Limited P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www.ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.
Customer Assistance In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss Warranty Act, or to the extent allowed by state law, before pursuing replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws.
Customer Assistance The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligibility limitations, modify procedures and/or to discontinue this service without notice and without incurring obligations per applicable state law.
Customer Assistance Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs To have your case reviewed you must complete the application in the DSB brochure and mail it to the address provided on the application form. Some states will require you to use certified mail, with return receipt requested.
Customer Assistance Making a decision Board members review all available information related to each complaint, including oral presentations, and arrive at a fair and impartial decision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date that all requested information is received by the Board. Since the Board generally meets once a month, it may take longer for the Board to consider some cases.
Customer Assistance The CAMVAP program is a straight-forward and relatively speedy alternative to resolve a disagreement when all other efforts to produce a settlement have failed. This procedure is without cost to you and is designed to eliminate the need for lengthy and expensive legal proceedings. In the CAMVAP program, impartial third-party arbitrators conduct hearings at mutually convenient times and places in an informal environment.
Customer Assistance If you are in another foreign country, contact the nearest Ford dealership. If the dealership employees cannot help you, they can direct you to the nearest Ford affiliate office. If you buy your vehicle in North America and then relocate outside of the U.S. or Canada, register your vehicle identification number (VIN) and new address with Ford Motor Company Worldwide Direct Market Operations.
Customer Assistance 1. Two or more repair attempts are made on the same nonconformity likely to cause death or serious bodily injury OR 2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3.
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlight. • Always use a clean sponge or carwash mitt with plenty of water for best results.
Cleaning PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jam) to your dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products.
Cleaning • 2.0L EFI • 2.5L EFI • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer.
Cleaning • For routine cleaning, use Detail Wash (ZC-3–A). • If tar or grease spots are present, use Ford Extra Strength Tar and Road Oil Removal (B7A-19520–AA). WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleaned regularly. If the wiper does not wipe properly, substances on the windshield, rear window or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, tree sap, or other organic contamination.
Cleaning Do not use chemical solvents or strong detergents when cleaning the seat where the side air bag is mounted. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision. The air bag may not function correctly and not provide injury reduction benefits. INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: • Remove dust and loose dirt with a vacuum cleaner.
Cleaning UNDERBODY Flush the complete underside of your vehicle frequently. Keep body and door drain holes free from packed dirt. FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your Warranty Guide to find out which parts and services are covered.
Maintenance and Specifications Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in neutral. 2.
Maintenance and Specifications 2. Go to the front of the vehicle and release the auxiliary latch that is located in the center top of the grill. 3. Lift the hood and support it with the strut in the yellow-colored retainer; ensuring it is secure.
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L I4 engine 2 1 9 8 7 1. Power steering fluid reservoir 2. Brake fluid reservoir 3. Air filter assembly 4. Power distribution box 5. Battery 6. Engine oil filler cap 7. Engine oil dipstick 8. Engine coolant reservoir 9.
Maintenance and Specifications 2.5L V6 engine 1 10 2 9 8 7 3 4 6 5 1. Power steering fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Brake fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8. Engine oil dipstick 9. Engine coolant reservoir 10.
Maintenance and Specifications Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification ESR-M17P5–A. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Maintenance and Specifications • 2.0L I4 engine • 2.5L V6 engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Maintenance and Specifications Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4.
Maintenance and Specifications that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service.
Maintenance and Specifications When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing.
Maintenance and Specifications R TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application). • Refer to the Scheduled Maintenance Guide for service interval schedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter.
Maintenance and Specifications To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: • Add the type of coolant originally equipped in your vehicle. If you are unsure which type of coolant your vehicle requires, check your coolant reservoir or contact your local dealer. • Do not add/mix a green-colored coolant such as Motorcraft Premium Engine Coolant, VC-4–A, meeting Ford specification ESE—M97B44–A with the factory-filled coolant.
Maintenance and Specifications To avoid personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (an opaque plastic bottle).
Maintenance and Specifications Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%.
Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others.
Maintenance and Specifications • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water.
Maintenance and Specifications 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stays on after you start the engine, the fuel filler cap may not be properly installed.
Maintenance and Specifications Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. For Cougar S vehicles, please use “Premium” unleaded gasoline with an octane rating of 91. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fill-ups or fuel gauge readings are NOT accurate as a measure of fuel economy. We do not recommend taking fuel economy measurements during the first 1 600 km (1 000 miles) of driving (engine break-in period).
Maintenance and Specifications 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple calculations in order to determine fuel economy: Multiply liters used by 100, then divide by total kilometers traveled. Divide total miles traveled by total gallons used.
Maintenance and Specifications • Warming up a vehicle on cold mornings is not required and may reduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fuel economy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter.
Maintenance and Specifications It is important to note the box in the lower left corner of the window sticker. These numbers represent the Range of L/100 km (MPG) expected on the vehicle under optimum conditions. Your fuel economy may vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards.
Maintenance and Specifications permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal identifies engine displacement and gives some tune up specifications. Please consult your Warranty Guide for complete emission warranty information.
Maintenance and Specifications 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir.
Maintenance and Specifications Do not let the fluid level in the reservoir for the master cylinder fall below the MIN mark. If master cylinder runs dry, this may cause the brakes to fail. CLUTCH FLUID (IF EQUIPPED) The clutch master cylinder and brake master cylinder are part of the same system; both are refillable through the brake master cylinder with brake fluid. For more information on brake fluid maintenance, refer to Brake fluid in this chapter. Brake fluid is toxic.
Maintenance and Specifications 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6.
Maintenance and Specifications High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used.
Maintenance and Specifications INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: • Treadwear 200 Traction AA Temperature A These Tire Quality Grades are determined by standards that the United States Department of Transportation has set.
Maintenance and Specifications The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and Specifications • Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the label.
Maintenance and Specifications Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Driving too fast for conditions creates the possibility of loss of vehicle control. Driving at very high speeds for extended periods of time may result in damage to vehicle components. Snow tires must be the same size and grade as the tires you currently have on your vehicle.
Maintenance and Specifications REFILL CAPACITIES Fluid Brake fluid Engine coolant1 Engine oil (includes filter change) Fuel tank capacity Power steering fluid Transmission fluid4 Windshield washer fluid Ford Part Name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid Motorcraft Specialty Orange Engine Coolant Application Capacity All Fill to MAX mark Motorcraft SAE 5W-20 Premium Synthetic Blend Motor Oil N/A 2.0L engine 6.6L (7.0 quarts)2 9.5L (10.0 quarts)2 9.7L (10.2 quarts)3 4.25L (4.
Maintenance and Specifications LUBRICANT SPECIFICATIONS Ford Part Name or Equivalent Brake fluid Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid Door latch, hood Multi-Purpose latch, auxiliary Grease hood latch, trunk latch, seat tracks.
Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system 2.0L engine 121 87 octane 1–3–4–2 1.37 mm (0.054 inch) Electronically Controlled 2.5L engine 152 87 octane 1–4–2–5–3–6 1.37 mm (0.054 inch) Electronically Controlled VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear mm (in) 4720 (186) 1769 (69.6) 1325 (52.2) 2 704 (106.5) 1506 (59.3) 1491 (58.
Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the driver’s door.
Maintenance and Specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) XXXXXXXXXXXXXXXXX 1. World manufacturer identifier 2. Brake type and gross vehicle weight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8.
Accessories FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for your vehicle through your local authorized Ford, Lincoln, Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Accessories Comfort and convenience Cargo liner Cargo net Cargo organizer Dash trim Engine block heater First aid kit Gearshift knob Highway safety kit Remote start Travel equipment Console armrest Daytime running lights (DRL) Removable luggage rack Removable luggage rack adapters (bike, ski and snowboard) Fog lamps Speed control Protection and appearance equipment Car cover Cargo liner Carpet floor mats Flat splash guards Front end covers (full and mini) Hood Deflectors Lubricants and oils Molded splash gu
Accessories For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label). Consult your dealer for specific weight information.
Index A ABS (see Brakes) .....................117 Air bag supplemental restraint system ..............................94–95, 99 and child safety seats ..............96 description ..........................95, 99 disposal ....................................102 driver air bag ....................97, 100 indicator light .............12, 98, 101 operation ...........................97, 100 passenger air bag .............97, 100 side air bag ................................99 Air cleaner filter ...............
Index Cleaning your vehicle engine compartment ..............162 instrument panel ....................164 interior .............................164–165 plastic parts ............................163 washing ....................................161 waxing .....................................161 wheels ......................................162 wiper blades ............................164 Climate control (see Air conditioning or Heating) ............44 Clock ..........................
Index dipstick ....................................172 filter, specifications ........174, 198 recommendations ...................174 refill capacities ........................199 specifications ..................200–201 Exhaust fumes ..........................116 F Floor mats ...................................68 Fluid capacities .........................199 Foglamps .....................................47 Fuel ............................................182 calculating fuel economy .......186 cap ........
Index Keys .......................................74–76 key in ignition chime ...............16 positions of the ignition .........112 check coolant ............................12 check engine .............................10 cruise indicator .........................13 door ajar ....................................15 high beam .................................14 low fuel ......................................13 low washer fluid .......................15 oil pressure ...............................
Index P Panic alarm feature, remote entry system ................................73 Parking brake ............................118 Parts (see Motorcraft parts) ....198 Power distribution box (see Fuses) ...............................139 Power door locks ........................70 Power mirrors .............................60 Power steering ..........................120 fluid, checking and adding ....190 fluid, refill capacity ................199 fluid, specifications .........200–201 Power Windows .........
Index rotating ....................................196 snow tires and chains ............198 tire grades ...............................196 treadwear ................................195 Towing .......................................130 recreational towing .................133 trailer towing ..........................130 wrecker ....................................151 Traction control ........................119 active light ................................13 Transaxle fluid, refill capacities ..............
