Contents Before driving Introduction 2 Instrumentation 6 Controls and features Seating and safety restraints 22 110 Starting and driving Starting 148 Driving 152 Roadside emergencies 166 Servicing Maintenance and care 186 Capacities and specifications 232 Customer assistance 237 Reporting safety defects 249 Index 250 All rights reserved.
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in. INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing.
Introduction These are some of the symbols you may see on your vehicle.
Introduction Vehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Correct Fluid Level Emission System Engine Air Filter Passenger Compartment Air Filter Jack MAX MIN Check fuel cap 5
Instrumentation Instrument panel dimmer control (pg. 22) Instrument cluster (pg. 8) Headlamp control (pg. 22) 3 2 4 5 RPM x 1000 6 7 1 H 8 0 C AUTO 1 40 30 20 10 50 60 60 40 70 80 100 120 80 140 20 MPH SERVICE ENGINE SOON 90 F 160 km/h TRIP A 100 E OFF AUTO 2 DIM PUSH INTERIOR RES ACCEL VOL CANCEL NEXT VOL COAST SET Turn signal lever (pg. 87) Windshield wiper/washer control (pg. 88) Foglamp control (pg. 23) Audio controls * (pg. 86) Speed control (pg.
Instrumentation Gearshift (including overdrive button) (pg. 157) Rear wiper/washer (pg. 88) Hazard flasher (pg. 167) Rear defroster (pg. 42) VE DRI ON ER OV OFF/ HAZAR RR WA RR DEF SECUR SH Auxiliary power point (pg. 81) D RR WIP ER OG ITY Audio system (pg. 42) VOL - PUSH ON AM FM DC 12V CLK BASS TREB BAL FADE CD SEEK SCAN TUNE SIDE 1 - 2 EJ REW DISCS CD CD 1 2 1 TAPE AMS 3 4 FF COMP SHUFFLE 5 6 Climate control system (pg.
Instrumentation WARNING LIGHTS AND CHIMES Standard analog instrument cluster 3 2 4 RPM x 1000 6 20 7 1 H 40 30 5 10 8 0 50 60 60 40 70 80 100 120 80 140 20 90 F 160 MPH km/h 0 C 100 E TRIP A CRUISE R N D 2 1 P SET Optional electronic instrument cluster CRUISE OUTSIDE TEMP INST ECONOMY AVG.
Instrumentation Momentarily illuminates when the ignition is turned ON. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter.
Instrumentation Door ajar • Standard analog instrument cluster • Optional electronic instrument cluster Illuminates when the ignition is in the ON or START position and any door is open. High beams Illuminates when the high beam headlamps are turned on. Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster, check for a burned-out turn signal bulb.
Instrumentation • Optional electronic instrument CRUISE cluster This light comes on when either the COAST/SET or RES/ACCEL controls are pressed. It turns off when the cruise cancel control is pressed, the brake is applied or the ignition is turned to the OFF position. Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel Gauge in this chapter for more information).
Instrumentation The Service Engine Soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted. The vehicle will usually be drivable and will not require towing.
Instrumentation O/D off Illuminates when the Transmission O/D Control Switch (TCS), refer to OFF Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation. The light may also flash steadily if a transmission malfunction is detected.
Instrumentation GAUGES Standard analog instrument cluster gauges 3 2 4 6 20 7 1 H 40 30 5 RPM x 1000 10 8 0 50 60 60 40 70 80 100 120 80 140 20 90 F 160 MPH km/h 0 C 100 E TRIP A CRUISE P SET R N D 2 1 Optional electronic instrument cluster gauges CRUISE 5 6 7 8 F 2 ˚F ˚C MILES/BAL L/100 km OUTSIDE TEMP INST ECONOMY AVG.
Instrumentation • Optional electronic instrument cluster CRUISE 5 4 3 6 7 8 2 MPH km/h km 1 X 1000 TRIP 1 TRIP 2 RPM 0 Speedometer Indicates the current vehicle speed. • Standard analog instrument cluster 40 30 60 40 20 10 50 60 70 80 100 120 80 140 20 90 160 MPH km/h 0 100 TRIP A • Optional electronic instrument cluster CRUISE 4 3 5 6 7 8 2 MPH km/h km 1 0 X 1000 TRIP 1 TRIP 2 RPM Odometer Registers the total kilometers (miles) of the vehicle.
Instrumentation • Optional electronic instrument cluster CRUISE 3 4 5 6 7 8 2 MPH km/h km 1 0 X 1000 TRIP 1 TRIP 2 RPM Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. Trip odometer Registers the kilometers (miles) of individual journeys. • Standard analog instrument cluster To reset, press and hold the control for one second.
Instrumentation • Standard analog instrument cluster F E • Optional electronic instrument cluster F 1/2 E Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the ignition and let it cool. Refer to Engine coolant in the Maintenance and care chapter.
Instrumentation • Optional electronic instrument cluster H N O R M A L C ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: • display the outside temperature. • change your gauges from English ˚F ˚C to metric units. MILES/GAL L/100 km MILES km • monitor the instantaneous fuel OUTSIDE TEMP economy. INST ECONOMY AVG ECONOMY • monitor the average fuel TO EMPTY economy.
Instrumentation • • • • OUTSIDE TEMP INST ECONOMY AVG ECONOMY TO EMPTY ˚F ˚C MILES/GAL L/100 km MILES km OUTSIDE TEMP INST ECONOMY AVG ECONOMY TO EMPTY RESET Press this control to reset the average fuel economy calculation. ENG/MET Press this control to change your instrument cluster gauges from RESET ENG / MET TRIP / RST English to metric.
Instrumentation INST ECONOMY Press SELECT until the menu displays INST ECONOMY. This will display your fuel economy in ˚F ˚C MILES/GAL liters/100 km or miles/gallon based L/100 km MILES km on the type of traffic you are in. OUTSIDE TEMP INST ECONOMY Your vehicle must be moving to AVG ECONOMY TO EMPTY calculate instantaneous fuel economy. When your vehicle is not moving, this function shows 99 L/100km or 0 MILES/GAL. Instantaneous fuel economy cannot be reset.
Instrumentation 2. Select AVG ECONOMY. 3. Press the RESET control to clear the system memory. RESET ENG / MET TRIP / RST • Actual highway fuel economy is now displayed. This current SELECT OD / TRIP average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed. This is most noticeable in hilly environments. 4. Drive the vehicle at least 8 km (5 miles) with the speed control system engaged to display a stabilized average. 5.
Controls and features PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. DIM • Push and hold top of control to brighten. • Push and hold bottom of control to dim. The dome lamp will not illuminate if the control switch is in the OFF position. HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Push the control to turn on the interior lamps.
Controls and features Foglamp control Turn on the low-beam headlamps and press the foglamp control to activate the foglamps. The foglamp control will illuminate when the foglamps are on. Press the foglamp control a second time to deactivate the foglamps. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light OFF AUTO sensitive automatic on-off control of 1 the low-beam exterior lights AUTO normally controlled by the headlamp 2 control.
Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system 1 OFF 2 3 4 CLIMATE CONTROL SYSTEM MAX A/C A/C Fan speed control Controls the volume of air circulated in the vehicle. 1 2 3 4 Temperature control Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Controls and features The air conditioning operates in MAX A/C and when the A/C control is depressed. However, the air conditioning will only function if the outside temperature is about 4°C (40°F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. • MAX A/C-Uses recirculated air to cool the vehicle.
Controls and features • (Floor and defrost)-Distributes outside air through the windshield defroster ducts and the front and rear floor ducts. Heating and air conditioning capabilities are provided in this mode. Push A/C to cool the vehicle below the outside temperature.
Controls and features Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired. OFF REAR A/C 1 2 3 4 A/C Operating tips • In humid weather conditions, place the climate control system in DEF before driving.
Controls and features • Under normal weather conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants.
Controls and features To aid in side window defogging/demisting in cold weather conditions: 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to 4 (High) 4. Direct the outer panel vents towards the side windows To increase the airflow to the outer panel vents, close the central panel vents. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Controls and features The rear seat A/C system is controlled from the main climate control system on the instrument panel. Ensure that the control is set to REAR A/C to engage the rear passenger compartment air conditioning system. 1 OFF 2 3 MAX A/C 4 OFF REAR A/C 1 2 3 4 A/C Turning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C; set the mode selector to any position (other than OFF), and depress the A/C control. 1 OFF 2 3 MAX A/C 4 OFF REAR A/C 1 2 3 4 A/C 2.
Controls and features Turning the Rear A/C off: There are two ways to turn the rear air conditioning system off. The first way is to turn the Rear Fan Control on the main climate control system to OFF. OFF REAR A/C 1 2 3 4 A/C You can also turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. 0 1 4 3 REAR A/C 2 For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position.
Controls and features Turning the EATC on HI A/C OFF MAX TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO Press AUTOMATIC, any of the override controls or the fan speed control. The EATC will only operate when the engine is running. Turning the EATC off Press OFF. OFF TEMP AUTOMATIC OFF REAR 1 A/C Automatic operation Press AUTOMATIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window.
Controls and features If unusual conditions exist (i.e. window fogging, etc.), the manual override controls allow you to adjust the mode selector and fan speed controls as necessary. Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan ) if automatic fan speed is not desired. speed ( To control the temperature, select any temperature between 15°C (60°F) and 32°C (90°F) by pressing the temperature controls.
Controls and features Temperature conversion HI A/C OFF MAX TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO Press A/C and simultaneously for one second while turning the fan speed dial upward until it stops moving, to switch between Fahrenheit and Celsius. Fan speed ( ) When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the thumbwheel to cancel automatic fan speed operation.
Controls and features Manual override controls A/C OFF HI MAX TEMP AUTOMATIC OFF REAR 1 A/C 2 3 4 LO The override controls allow you to: • manually control where the airflow is directed • manually control the air conditioning operation • manually select between outside or recirculated air during air conditioning operation The air conditioning can operate in all modes except OFF. It will also operate only when required when AUTOMATIC has been selected.
Controls and features • (Panel)-Distributes outside air through the instrument panel registers. Heating and air conditioning capabilities are provided in this mode. Push A/C to cool the vehicle below the outside temperature. (Panel and floor)-Distributes outside air through the instrument • panel registers and the front and rear floor ducts. Heating and air conditioning capabilities are provided in this mode. Push A/C to cool the vehicle below the outside temperature.
Controls and features Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF, if rear heating is desired. OFF REAR 1 A/C 2 3 4 Operating tips • In humid weather, select (Defrost) before driving. This will reduce fogging on your windshield.
Controls and features • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. • If your vehicle has been parked with the windows closed during warm weather conditions, the air conditioner will perform more efficiently in cooling the vehicle if driven for two or three minutes with the windows open.
Controls and features Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop. Rear passenger air conditioning system — EATC systems On vehicles equipped with front passenger EATC systems, the vehicle will also have rear passenger compartment climate controls, which allow the rear seat occupants to adjust their air conditioning level.
Controls and features The rear seat A/C system is controlled from the main climate control system on the instrument panel. Ensure that the control is set to REAR A/C to engage the rear passenger compartment air conditioning system. A/C OFF HI MAX OFF REAR 1 A/C TEMP AUTOMATIC 2 3 4 LO Turning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C; set the mode selector to any position (other than OFF), and depress the A/C control.
Controls and features Turning the Rear A/C off: There are two ways to turn the rear air conditioning system off. The first way is to turn the Rear Fan Control on the main climate control system to OFF. OFF REAR 1 A/C 2 3 4 You can also turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. 0 1 4 3 REAR A/C 2 For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position.
Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the rear defroster is activated. HAZARD RR WASH RR WIPER RR DEFOG SECURITY The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 15 minutes or when the ignition is turned to the OFF position.
Controls and features Volume/power control Press the control to turn the audio system on or off. Turn the control to raise or lower volume. VOL - PUSH ON VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped).
Controls and features Tune adjust in radio mode • Press to move to the next SEEK frequency down the band (whether or not a listenable TUNE station is located there). Hold the DISCS control to move through the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD changer (if equipped) • Press to select the previous SEEK disc in the CD changer.
Controls and features • Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay. Scan function The scan function works in radio or CD changer mode (if equipped). SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode.
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features Tape select • To enter tape mode while in radio or CD changer mode, press the TAPE control. • If no tape is found, NO TAPE appears in the display. CLK TAPE AMS Automatic Music Search The Automatic Music Search feature allows you to quickly locate the CLK beginning of the tape selection being played or to skip to the next selection. TAPE AMS To activate the feature, momentarily depress the TAPE AMS button.
Controls and features Press the 1–2/FF control to stop rewinding the tape. SIDE REW To rewind in CD changer mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. 1-2 FF CD 1 Fast forward The fast forward control works in tape and CD changer modes. To fast forward in tape mode, press SIDE 1 - 2 the 1–2/FF control. Tape direction will automatically REW FF reverse when the end of the tape is reached.
Controls and features Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Tape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. SIDE REW 1-2 FF EJ DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise 4 reduction reduces the amount of hiss and static during tape playback.
Controls and features • • to decrease hours and to increase hours. SEEK SEEK TUNE TUNE To set the minute, press and hold the CLK control and press the TUNE control: CLK TAPE AMS • • to decrease minutes and to increase minutes. SEEK SEEK TUNE TUNE The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time).
Controls and features CD 1 CD 2 3 4 COMP SHUFFLE 5 6 To turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the radio display. Pressing 3 and 5 at the same time again will turn the rear seat controls off. Adjusting the volume Press the + control to increase volume. VOLUME MEDIA MEM SEEK Press the — control to decrease volume. From the RSC, the loud speaker volume can not be set higher than the current volume radio setting.
Controls and features Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, or CD changer (if equipped). Memory preset control Push the MEM control successively to allow rear sear passengers to scroll through the six memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc.
Controls and features Premium AM/FM Cassette (CD changer compatible) BASS BAL SEL TREB VOL PUSH ON CD EJ TAPE AM FM TUNE SEEK MUTE REW FF SIDE 1.2 1 2 3 RDS / CLK SCAN 4 FADE AUTO COMP SHUFF 5 6 Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off.
Controls and features If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped). AM FM AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Controls and features Seek function The seek function control works in radio, tape or CD changer mode (if equipped). Seek function in radio mode • Press to find the next SEEK listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape or return to the beginning of the current selection. • Press to listen to the next selection on the tape.
Controls and features Scan function in CD changer mode (if equipped) Press the SCAN control to hear a short sampling of all selections on the CD (The CD scans in a forward direction, wrapping back to the first track at the end of the CD.). To stop on a particular selection, press the control again. Radio station memory preset The radio is equipped with six station memory preset controls. These controls can be used to select up to six preset AM stations and twelve FM stations (six in FM1 and six in FM2).
Controls and features Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output. BASS SEL TREB Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. BASS SEL TREB Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. BAL SEL FADE Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers.
Controls and features • To begin CD play (if CD[s] are loaded), press the CD control. CD TAPE The first track of the disc will begin playing. After that, CD play will begin where it stopped last. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Rewind The rewind control works in tape REW and CD changer modes (if equipped).
Controls and features DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise reduction reduces the amount of 4 hiss and static during tape playback. Press the control to activate (and deactivate) Dolbyt noise reduction. Dolbyt noise reduction is manufactured under license from Dolbyt Laboratories Licensing Corporation. “Dolbyt” and the double-D symbol are trademarks of Dolbyt Laboratories Licensing Corporation.
Controls and features Press the RDS/CLK control until RDS OFF is displayed. • Use the SEL control to select ON or OFF. SEL Traffic • Press the RDS control until TRAFFIC is displayed. RDS / CLK • Use the SEL control to select ON or OFF. With the feature on, use the SEEK or SCAN control to SEL find a radio station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets.
Controls and features • • • • Religious Rock Soft Top 40 Show • With RDS activated, press the RDS control until SHOW is displayed. • Use the SEL control to select the program TYPE, station NAME or NONE (no text displayed). Setting the clock Press the CLOCK control until SELECT HOUR or SELECT MINS is displayed. Use the SEL control to manually set the time. to increase • Press hours/minutes. • Press to decrease hours/minutes. Mute mode Press the control to mute the playing media.
Controls and features Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). REW FF SIDE 1.2 1 2 3 VOLUME 4 MEDIA MEM SEEK COMP SHUFF 5 6 To turn on the rear seat controls, press the memory preset controls 3 will appear in the radio display. and 5 at the same time. The Pressing 3 and 5 at the same time again will turn the rear seat controls off.
Controls and features Plug a 3.6 mm headphone (not VOLUME MEDIA MEM SEEK included) into either one of the two jacks. Press the / control to operate the headphones. DUAL PLAY will appear in the digital display of the audio system, signaling that your Personal Audio System has been activated. The rear speakers will cut out once the speaker on/off control is pressed. A soft audible sound may be heard from the rear speakers. The front / speaker will remain playing for the front passengers.
Controls and features In tape mode, use the SEEK function to access the next previous selection. or Super Sound AM/FM Stereo/Cassette/Single CD Player (CD Changer Compatible) DISC VOL - PUSH ON EJ FM1 MUTE ST AM FM EJ DOLBY B NR TAPE CD AUTO FADE RDS CLK SEEK TUNE SCAN BASS TREB REW FF SIDE 1-2 1 2 3 SEL 4 BAL COMP SHUFFLE 5 6 Your audio system is equipped with selective lighting, a unique lighting strategy. This lighting feature is operable when the headlamps are illuminated.
Controls and features Turn control to raise or lower volume. VOL - PUSH ON If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. If you wish to maintain your preset volume level, turn the audio system off with the power control before switching off the ignition. AM/FM select The AM/FM select control works in radio, tape and CD modes.
Controls and features Tune adjust for CD changer (if equipped) • Press to select the previous SEEK SEEK disc in the CD changer. (Play will begin on the first track of the TUNE TUNE disc unless the CD changer is in shuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. to select the next disc in the CD changer. Hold the control • Press to fast-forward through the remaining discs.
Controls and features Scan function The scan function works in radio, tape or CD mode. SCAN Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction.
Controls and features Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. AUTO 3. When the first six strong stations RDS are filled, the station stored in CLK memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all store the last strong station available.
Controls and features Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and to shift sound to the right. • Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the FADE control then press: • to shift sound to the front and to shift sound to the rear.
Controls and features Rewind The rewind control works in tape REW and CD modes. 1 • In tape mode, radio play will continue until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. • In CD mode, pressing the REW control for less than three seconds results in slow rewind. Pressing the control for more than three seconds results in fast rewind. Fast forward The fast forward control works in FF tape and CD modes.
Controls and features DolbyT noise reduction Dolbyt noise reduction operates only in tape mode. Dolbyt noise 4 reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolbyt noise reduction. The Dolbyt noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation. Dolbyt and the double-D symbol are trademarks of Dolbyt Labratories Licensing Corporation.
Controls and features To set the minute, press the RDS/CLK control until SELECT MIN is displayed and press: • • to decrease minutes and to increase minutes.
Controls and features To see if any stations in your area are capable of broadcasting an RDS traffic alert, press SCAN or SEEK while TRAFFIC ON is displayed. The radio will then SCAN or SEEK only to traffic capable stations. RDS select program type • Press the RDS control until FIND program type is displayed. AUTO RDS CLK • Use the SEL control to select the desired program type.
Controls and features will be displayed along with the frequency. Press SEL in order to scroll through the text messages. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. EJ MUTE Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, CD, or CD changer (if equipped).
Controls and features Adjusting the volume Press the + control to increase volume. VOLUME MEDIA MEM SEEK Press the — control to decrease volume. From the RSC controls, the speaker volume can not be set higher than the current volume radio setting. Once in headphone mode, the RSC volume controls will only change volume in the headphones to a desired level and will have no effect on the front speakers (muting the speakers will not mute the headphones).
Controls and features Memory preset control Push the MEM control successively to allow rear seat passengers to scroll through the six memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. VOLUME MEDIA MEM SEEK Seek function • Press to find the next listenable station down the VOLUME MEDIA MEM SEEK frequency band. • Press to find the next listenable station up the frequency band.
Controls and features 2. Press EJECT to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. A B C A If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A).
Controls and features 5. Line up the CD with the groove of the disc holder. Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks securely into the magazine. If the disc holders are not fully locked into the magazine, the unit will not operate. Ensure that the disc holder is evenly inserted and at the same level as the magazine (A). The unit will not operate if the disc holder is not inserted at the same level (B).
Controls and features If • • • • your changer does not work, it may be that: A disc is already loaded where you want to insert a disc. The disc is inserted with the label surface downward. The disc is dusty or defective. The player’s internal temperature is above 60°C (140°F). Allow the player to cool down before operating. • A disc with format and dimensions not within industry standards is inserted. Cleaning compact discs Inspect all discs for contamination before playing.
Controls and features • Do not leave tapes in the cassette player for a long time when not being played. Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission(CRTC) establish the frequencies AM and FM stations may use for their broadcasts. Allowable frequencies are: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all frequencies are used in a given area.
Controls and features AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The power point is an additional power source for electrical accessories. There are two auxiliary power points: • One is located on the instrument panel. DC 12V • The second is located in the drivers side 2nd row trim panel.
Controls and features POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine 3 and all accessories/locks the steering wheel, gearshift lever and allows key 2 removal. 4 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 1 3. ON, all electrical circuits operational. Warning lights illuminated. Key position when driving. 4. START, cranks the engine. Release the key as soon as the engine starts. SPEED CONTROL To turn speed control on • Press ON.
Controls and features To turn speed control off • Press OFF. RES ACCEL ON CANCEL OFF COAST SET Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press COAST/ SET. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RES ACCEL ON CANCEL OFF COAST SET If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal.
Controls and features To set a higher set speed • Press and hold RES/ACCEL. Release the control when the RES ACCEL desired vehicle speed is reached or ON • Press and release RES/ACCEL to CANCEL operate the Tap-Up function. OFF Each press will increase the set COAST speed by 1.6 km/h (1 mph) or SET • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release COAST/SET. You can accelerate with the accelerator pedal at any time during speed control usage.
Controls and features To disengage speed control • Depress the brake pedal. • Press CANCEL. Disengaging the speed control will not erase the previously programmed set speed. RES ACCEL ON CANCEL OFF COAST SET • Press OFF. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES/ACCEL. For RES/ACCEL to operate, the vehicle speed must be faster than 48 km/h (30 mph). RES ACCEL ON CANCEL OFF COAST SET Indicator light • Standard analog instrument CRUISE SET cluster The “CRUISE” light comes on when the ON control is pressed. The “SET” light comes on when either the COAST/SET or RES/ACCEL controls are pressed. The “SET” light turns off when the cruise cancel control is pressed or the brake is applied.
Controls and features Audio control features In Radio mode: • Press NEXT to select the next preset station within the current radio band. In Tape mode: • Press NEXT to listen to the next selection on the tape. In CD mode: • Press NEXT to listen to the next track on the disc. In any mode: • Press VOL up or down to adjust the volume. VOL NEXT VOL VOL NEXT VOL TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle. The washer will automatically shut off after ten seconds of continuous use.
Controls and features Press the washer control to activate the rear washer. The wiper will come on when the washer control is pressed, if it is not already on. HAZARD RR WASH RR WIPER RR DEFOG SECURITY HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. OVERDRIVE CONTROL Activating overdrive D (Overdrive) is the normal drive position for the best fuel economy.
Controls and features For additional information about the gearshift lever and the transmission control switch operation refer to the Automatic Transaxle Operation section of the Driving chapter. TILT STEERING WHEEL Push the tilt steering wheel lever downward to move the steering wheel up or down. Push the control upward to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. POWER WINDOWS • Press and hold the switch to open.
Controls and features Power vent windows (if equipped) Your vehicle may be equipped with rear power vent windows which are operated the same as the front power windows. AUTO L VENT R One touch down • Press AUTO completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. AUTO Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the control.
Controls and features POWER DOOR LOCKS Push control forward to unlock all doors and pull backward to lock all doors. UNLOCK Anti-lockout This feature prevents the front doors from being locked while the key is in the ignition and the driver’s door is open. Remove the key from the ignition before exiting the vehicle. Central locking When unlocking the front doors with the key, turn the key once toward the rear of the vehicle to unlock that door only.
Controls and features Pull lock control out to engage the lock. Push control in to disengage childproof locks. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. To adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror.
Controls and features 2. Move the control in the direction you wish to tilt the mirror. MIRRORS L R 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.
Controls and features Programming Do not program the HomeLinkt Universal Transceiver with the vehicle parked in the garage. 1. Prepare for programming the HomeLinkt Universal Transceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2.
Controls and features To program your hand-held transmitters: • continue to hold the button on the HomeLinkt Universal Transceiver. • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLinkT Universal Transceiver Once programmed, the HomeLinkt Universal Transceiver can be used in place of hand-held transmitters.
Controls and features 3. Press and release the programmed HomeLinkt button. Press and release the HomeLinkt button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door. The HomeLinkt Universal Transceiver has now been trained to the receiver. The remaining two buttons may now be programmed if this has not previously been done.
Controls and features ILLUMINATED VISOR MIRROR To turn on the visor mirror lamps, lift the mirror cover. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror. Push up to access the conversation mirror. Pull down on the housing to lock it in place.
Controls and features The dome lamp will stay on if the control is moved to the ON position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the OFF OFF ON— position, the lamp will not come on at all. The dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 15 seconds after the door is shut.
Controls and features If the battery is disconnected, discharged, or a new battery is installed, the moon roof needs to be opened to the vent position to reset the moon roof positions. If you open and close the moon roof repeatedly, the moon roof motor may overheat and shut down for 45 seconds while the motor cools. Do not let children play with the moon roof. They may seriously hurt themselves. CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with a variety of console features.
Controls and features REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Controls and features Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, the horn will chirp and the lamps will flash. The horn chirp feature can be turned on/off by holding the LOCK and UNLOCK controls on the transmitter simultaneously for two seconds. The hazard lights will flash three times each time the system is toggled between active and non-active modes. If any of the doors are ajar, the horn will not chirp and the lights will not flash.
Controls and features The battery saver will shut off the interior lamps after 30 minutes if the front door is left open or after 60 minutes if the liftgate is left open. Replacing the battery The transmitter is powered by one coin type three-volt lithium battery. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle.
Controls and features Re-insert the key and turn to the ON position. Press any control on the first transmitter. The park lamps will flash twice to confirm the programming. To program additional (up to four) transmitters yourself: • Unlock, then lock the driver’s door using the power door lock switch. • Press any control on the next transmitter to be programmed. The park lamps will flash twice to confirm the acceptance of registration. Repeat this step for additional transmitters.
Controls and features If a door is open, the system is prearmed and is waiting for the door to close. Once all the doors are closed, the security indicator lamp on the instrument panel will illuminate continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds and the security indicator lamp will begin to flash.
Controls and features Disarming a triggered anti-theft system You can disarm the system by any of the following actions: • Press the unlock control using your remote entry transmitter. • Unlock the doors with a key. LIFTGATE To open the liftgate window (if equipped), insert key into lock and turn clockwise. The window unlatches and the wiper moves out of the way. To open the liftgate, insert key into lock and turn counterclockwise. Pull back and upward on liftgate handle to fully open liftgate.
Controls and features Cargo Area Features Rear Cargo net The cargo net helps stabilize lightweight objects in the cargo area. Attach the net to the anchors provided. The cargo restrained in the net must not exceed 22 kg (50 lbs.) or the net may not stay secured. The cargo net is not designed to restrain objects during a collision or heavy braking. Front Cargo net (if equipped) The front cargo net can be used to hold small items between the front seats.
Controls and features LOC Parcel Shelf (if equipped) Your vehicle may be equipped with a 14 kg (30 lbs.) maximum capacity parcel shelf located behind the rear seat of your vehicle which can be positioned to three different heights. To remove the shelf: 1. Open the liftgate. 2. Disconnect the net loop from the retainer underneath the shelf to access the lock knob. 3. Turn the lock knob counterclockwise and slide the knob to the UNLATCH position. 4. Remove the shelf from the vehicle.
Controls and features Make sure the rear seat back is in the rearmost/upright position when parcel shelf is loaded. Do not load any objects on the parcel shelf that may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Failure to secure cargo under the cargo net will increase the risk of the cargo striking occupants in the case of a sudden stop or collision. Do not load the parcel shelf through the liftgate glass.
Seating and safety restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. Refer to the following to raise and lower the head restraints.
Seating and safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the power seats (if equipped) The power seat controls are located on the outboard side of the seat. Never adjust the driver’s seat or seatback when the vehicle is moving.
Seating and safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Move the control up or down to move the seat up and down. • 6 way (driver seat) Slide the control forward or backward to move the seat forward or backward. • 6 way (driver seat) • 4 way (passenger seat) Rotate the vertical control to adjust the seatback.
Seating and safety restraints Using the manual lumbar support The lumbar control is located on the inboard side of the driver’s seat. Move the control up or down to adjust lumbar support. Memory seats and mirrors (if equipped) Some vehicles may only have the memory feature available for the seats. The memory seat control is located 1 on the driver’s door panel.
Seating and safety restraints 2. Press and hold the desired memory position button. Within ten seconds, press the unlock button on the transmitter while the memory button is pressed. 3. When the transmitter has been programmed, the indicator will flash five times. The indicator light will remain illuminated until the memory button is pressed again or ten seconds lapse. To remove a programmed seat position: 1.
Seating and safety restraints • 4 passenger vehicle (with third row seat in storage position) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH A B C B • 5 passenger vehicle (second row seats removed) A. Cargo mat B. Narrow mats C.
Seating and safety restraints • 5 passenger vehicle (second row seats removed and third row bench seat moved forward to limousine seating position) A. Cargo mat B. Narrow mats B A • Two passenger vehicle (second row seats removed and third row seat stored in full forward position — if equipped with Rear Seat Entertainment System, the third row seat cannot be put into this position.) A. Cargo mat B.
Seating and safety restraints Stowed cupholders The vehicle is equipped with cupholders that pull out from the 2nd row seat: • Bench seat - below center of the seat cushion • Bucket seat (driver’s side only) inboard side of seat base Use only soft cups in the cupholder. Hard objects can injure you in a collision. Adjusting 2nd row bench Pull control up to flip seatback to forward flat position.
Seating and safety restraints 2nd row bucket seats (if equipped) • Adjusting the left side bucket seat Pull control up to recline the seatback or fold the seatback flat. • Adjusting the right side (E-Z Entry Tip Slide) bucket seat The E-Z Entry Tip Slide seat allows for easier entry and exit to and from the 3rd row seat. The E-Z Entry system will slide the seat and tip the seatback forward (the seatback must be in the upright position). To enter the 3rd row seat, pull up on the seatback recline handle.
Seating and safety restraints To exit the third row seat, pull up on the 3rd row access control. To return the seat to a seating position, move the seat rearward until the seat track locks. Then readjust the seatback. Lift handle to move the seat forward or backward.
Seating and safety restraints Pull control up to flip seatback to a forward flat position. Adjusting 3rd row bench Pull control up to adjust seatback position. This control will also allow the seatback to be put in the forward flat position.
Seating and safety restraints A C B The entire seat can be moved to four seating positions and two storage positions. Before rearranging the seats, remove any floor mats that might be in the way, see Removable floor mats in this chapter for instructions on placement of floor mats. For vehicles equipped with a second row bench seat: If the three passenger bench seat is moved up to the second row position, the outside passenger (opposite the driver) should fasten the standard lap/shoulder belt.
Seating and safety restraints To move the seat to another seating or storage position: 1. Lift control (A) to release the seat cushion and flip the cushion up. The seat cushion must be moved to the storage position before the seat can be moved along the track. A 2. Pull control (B) to move the seat forward or backward until it locks into position. The seat cushion cannot be lowered if the seat is in a storage position.
Seating and safety restraints After sliding the seat, check to ensure that both sides of the seat are locked in position. This must be done before the vehicle is put into motion in order to prevent unintended movement of the seat. Every time you adjust any seat, check to be sure that it is properly latched in the lock position of both seat tracks. If the seat is not properly latched, it could come loose and increase the risk of severe injury or death in an accident. The 3rd row bench seat is not removable.
Seating and safety restraints To install the seat: The bucket seats are not interchangeable due to the locations of the seat anchors on the floor of the vehicle. Each seat must be installed in its original position. 1. Position the seat in the vehicle. 2. Align seat front hooks to front anchors and push forward into place, lower back of seat into the rear anchors until both rear latches fully engage into place. Be sure that the seat is locked in place both front and back. 3.
Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.
Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movements and locking in response to vehicle movement.
Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Seating and safety restraints Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height adjuster down. To raise the height of the shoulder belt, slide the height adjuster up. Pull down on the height adjuster to make sure it is locked in place.
Seating and safety restraints Shorten and fasten the belt when not in use. Safety belt extension assembly If the safety belt assembly is too short for you, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt.
Seating and safety restraints Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, wears or cuts, replacing if necessary.
Seating and safety restraints Your vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity. This information will assist Ford in the servicing of your vehicle and may help Ford better understand real world collisions and further improve the safety of future vehicles.
Seating and safety restraints Steps you can take to properly position yourself away from the air bag: • Move your seat to the rear as far as you can while still reaching the pedals comfortably. • Recline the seat slightly (one or two degrees) from the upright position. Do not put anything on or over the air bag module. Placing objects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causing serious injury.
Seating and safety restraints Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Seating and safety restraints facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of air bag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the air bag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation. Do not touch them after inflation.
Seating and safety restraints If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles (including pretensioners) For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel.
Seating and safety restraints Follow all the important safety restraint and air bag precautions that apply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can be positioned so it does not cross or rest in front of the child’s face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit.
Seating and safety restraints When installing a child safety seat: • Review and follow the information presented in the Air Bag Supplemental Restraint System section in this chapter. • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. 1. Position the child safety seat in a seat with a combination lap and shoulder belt. Children 12 and under should be properly restrained in the rear seat whenever possible. 2.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. 5.
Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints 5. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt. 6. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is held securely in place. If the child seat moves excessively, repeat steps 5 through 6, or properly install the child seat in a different position.
Seating and safety restraints Second row seats 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Grasp the tether strap and position it to the seat frame.
Seating and safety restraints 4. Rotate the tether strap. 5. Clip the tether strap to the seat tether slot bracket at the lower rear portion of the seatback. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision.
Seating and safety restraints 6. Rotate the tether strap clip. 7. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 8. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Third row seats The third row seat child tether anchors are located on the bottom back side of the seat. Refer to Second row seats listed previously for installation instructions.
Seating and safety restraints Attaching child safety seats with Lower Anchor and Tethers for Children (LATCH) attachments Some child safety seats are labeled as LATCH or LATCH-compatible child seats. These seats include two rigid or webbing mounted attachments that connect to two anchors at specific seating positions in your vehicle. This type of child seat eliminates the need to use seat belts to attach the child seat.
Seating and safety restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Each lower anchor for child seat installation is located 2–3 inches below the locator symbols. Follow the child seat manufacturer’s instructions to properly install safety seats with LATCH lower anchors and LATCH-compatible attachments.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting 3. Make sure the parking brake is set. PUSH TO RELEASE 4. Make sure the gearshift is in P (Park). P R N D 2 1 5. Turn the key to 3 (ON) without 3 turning the key to 4 (START). If there is difficulty in turning the 2 key, firmly rotate the steering wheel 4 left and right until the key turns freely.
Starting CRUISE OUTSIDE TEMP INST ECONOMY AVG. ECONOMY TO EMPTY 5 4 3 6 7 8 F 2 ˚F ˚C MILES/BAL L/100 km H 1 0 X 1000 TRIP 1 TRIP 2 RPM MPH km/h km E FUEL DOOR AIR BAG ! P BRAKE P N O R M A L 1/2 R N D 2 1 C UNLEADED FUEL ONLY ABS SERVICE ENGINE SOON O/D OFF Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Starting system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle.
Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock ! P brake system is disabled and normal braking is still effective unless the BRAKE brake warning light also remains illuminated with parking brake released.
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. ! P BRAKE Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Driving • • • • • uneven vehicle loading high crown in center of road high crosswinds wheels out of alignment loose or worn suspension components AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed.
Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Understanding gearshift positions Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy. This feature is designed to optimize shift smoothness.
Driving Overdrive — column mounted gearshift with O/D off switch The Overdrive position with the O/D P R N D 2 1 OFF switch not depressed is the normal driving position for this automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy. Overdrive may not be appropriate for certain terrains.
Driving When to use D (Drive) or press the O/D OFF switch You will notice that there is only one P R N D 2 1 drive position on your gearshift indicator (instead of Drive and Overdrive). However, you will find a control labeled OVERDRIVE located OVERDRIVE OFF/ON on the gearshift lever. Push in the switch and the O/D OFF light in the instrument cluster will illuminate. With the O/D OFF light illuminated, the transaxle will operate in first, second and third gears and will not shift into fourth gear.
Driving When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running. If you do not take these precautions, your vehicle may move unexpectedly and injure someone.
Driving Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. Driving through deep water where the transaxle is submerged may allow water into the transaxle and cause internal damage.
Driving • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Do not exceed the GVWR or the GAWR specified on the certification label. Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GAWR limitations.
Driving TRAILER TOWING The trailer towing table shows the maximum allowable maximum GCWR and trailer weight. Maximum GCWR - kg (lbs.) 3 628 ( 8 000) Trailer weight range (0 - maximum) - kg (lbs.) 0-1 588 (0-3 500) Do not exceed the GVWR or the GAWR specified on the certification label. Towing trailers beyond the maximum recommended gross trailer weight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury.
Driving Trailer Tow Prep Package (if equipped) The trailer tow prep package on your vehicle (if equipped) includes: • Heavy duty battery • Conventional size spare tire • Trailer tow module and jumper harness Using the jumper harness (if equipped) • Remove the connector cap from the vehicle harness located behind the rear bumper. Store the connector cap in the glove box for reinstallation. • Connect the tow harness to the vehicle harness located behind the rear bumper.
Driving If you use a rental trailer, follow the instructions that the rental agency gives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Driving Trailer towing tips • Practice turning, stopping and backing up before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts.
Roadside emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New Vehicle Limited Warranty period (U.S.
Roadside emergencies Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–294–2582).
Roadside emergencies The fuel pump shut-off switch is located in the driver’s foot well, behind the kick panel. The reset button (RED) for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the RUN position.
Roadside emergencies Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses 2A 3A 4A 5A 7.
Roadside emergencies The fuses are coded as follows. Fuse/Relay Location Corner Lamps Heated Seat I/P Illum Electron Fuse Amp Passenger Compartment Rating Fuse Panel Description 10A Front Exterior Lamps 7.5A 7.5A 10A Tail Lamp Air Bag Audio Eng Cont Room Lamp Mirror 10A 10A 10A 10A 15A 7.
Roadside emergencies Fuse/Relay Location Cigar Lighter Hazard Fuse Amp Passenger Compartment Rating Fuse Panel Description 20A Cigar Lighter 10A RR Pwr Plug Rear Blower Front Wiper Rear Blower Rear Wiper O2 Sensor Audio/Video Turn Audio Amp Front Blower Eng Cont 20A 7.5A Relays 10A A/C Cont 7.5A Electron 10A Rear Defog Front Blower Rear Defog — Heated Mirror 20A 20A 15A 20A 15A 10A 7.
Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Location Fog Lamp FUEL PUMP INJ SEC RAD ECCS — — ALT ABS — H/L RH HORN — H/L LH — — ABS — PWR WND RAD FAN LO — IGN SW — RAD FAN FR BLW Fuse Amp Power Distribution Box Description Rating 7.5A* Fog Lamps 15A* Fuel Pump Relay 10A* Powertrain Control Module (PCM), Injectors 7.5A* Anti-Theft Relay, Smart Entry Control (SEC)/Timer Module 7.
Roadside emergencies Fuse/Relay Location RR DEF ALT Fuse Amp Power Distribution Box Description Rating 45A** Rear Window Defroster Relay 140A** Accessory Relay, Ignition Relay, Tail Lamp Relay, Fuse Junction Panel MAIN 100A** Generator * Mini Fuses ** Maxi Fuses Relay box The relay box is located in the engine compartment in front of the battery.
Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Temporary spare tire information Your vehicle may have a temporary or conventional size spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only.
Roadside emergencies Removing the spare tire 1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up the piece of carpet to expose the hex nut. 2. Insert the lug nut wrench on the hex nut in cargo floor. 3. Turn the wrench counterclockwise until tire is lowered to the ground and the cable is slightly slack. 4. Remove the retainer from the spare tire. It may be necessary to lift one end of the tire to disengage the retainer.
Roadside emergencies Stowing the spare tire 1. Lay the tire on the ground with the interior side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. Turn the wrench clockwise until the tire is raised to its original position underneath the vehicle. The hex nut ratchets when the tire is raised to the stowed position. It will not allow you to overtighten. 4. Check seating position of tire for looseness against the underbody supports and retighten if necessary.
Roadside emergencies 1. Park on a level surface, activate hazard flashers and set parking brake. PUSH TO RELEASE 2. Place gearshift lever in P (Park), turn engine OFF, and block the diagonally opposite wheel. 3. Remove the spare tire and jack assembly. 4. Remove the center ornament or wheel cover from the wheel with the tapered end of the jack handle that came with your vehicle. Insert and twist the handle, then pry against the wheel. 5.
Roadside emergencies 7. Turn the jack handle clockwise until the wheel is completely off the ground. To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Roadside emergencies Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not effect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation to its optimum shift feel. 1. Use only a 12–volt supply to start your vehicle. 2.
Roadside emergencies + + – – 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. + + – – 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. + + – – 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts of both engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3.
Roadside emergencies + + – – 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’s battery. + + – – 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. + + – – 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery.
Roadside emergencies After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. When the battery is disconnected or a new battery is installed, the transmission must relearn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will not effect function or durability of the transmission.
Roadside emergencies If your vehicle is to be towed from the rear using wheel lift equipment, the front wheels (drive wheels) must be placed on a dolly to prevent damage to the transmission. If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company provides a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered.
Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood and secure it with the prop rod.
Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.3L V6 engine 10 11 1 2 3 9 8 7 1. Power distribution box 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Relay box 6. Engine oil filler cap 7. Engine oil dipstick 8. Windshield washer fluid reservoir 9. Engine coolant reservoir 10. Power steering fluid reservoir 11.
Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P. 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil indicator (dipstick). L H 6.
Maintenance and care • If the oil level is below the L mark, add enough oil to raise the level within the L and H range. • Oil levels above the H mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2.
Maintenance and care Engine oil and filter recommendations Look for this certification trademark. SAE 5W-30 engine oil is recommended. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API certification trademark will meet all requirements for your vehicle’s engine. Ford oil specification is WSS-M2C153-G. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid from a clean un-opened container until the level reaches MAX. Do not fill above this line. 4.
Maintenance and care WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Only use a washer fluid that meets Ford specification. Refer to Lubricant specifications in the Capacities and specifications chapter.
Maintenance and care 60%, the engine parts could become damaged or not work properly. A 50/50 mixture of coolant and water provides the following: • freeze protection down to -36° C (-34° F). • boiling protection up to 129° C (265° F). • protection against rust and other forms of corrosion. • enables calibrated gages to function properly. When the engine is cold, check the level of the engine coolant in the reservoir.
Maintenance and care Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or a premium engine coolant that meets Ford specification ESE-M97B44-A. • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOLt engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D. • DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Maintenance and care mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level” or within the “cold fill range” as listed on the reservoir (depending upon application). Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month.
Maintenance and care Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • it may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage.
Maintenance and care 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is in this range. 5.
Maintenance and care 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6.
Maintenance and care Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transmission fluid may cause internal transaxle component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct.
Maintenance and care 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 5. Replace the air filter housing cover and secure the four clamps. BATTERY Your vehicle is equipped with a maintenance-free battery which normally does not require additional water during its life of service.
Maintenance and care If you see any corrosion on the battery or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. When the battery is disconnected or a new battery installed, the transmission must learn its adaptive strategy. As a result of this, the transmission may shift firmly. This operation is considered normal and will fully update transmission operation to its optimum shift feel.
Maintenance and care R TU LE AD RE If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries.
Maintenance and care odor itself and the perceptional threshold of the individual. The odor and particulate filtration system gives the following benefits to customers: • Improves the customer’s driving comfort by reducing odor and particle concentration • Improves the interior compartment cleanliness • Protects the climate control components from particle deposits The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle.
Maintenance and care B A C 2. Remove the six (6) screws (B) from the cowl grille (A) at the base of the windshield. 3. Open the hood. 4. Remove the four (4) plastic screws (C) from the forward edge of the cowl leaf screen under the hood. • Remove the four (4) screw anchors by pushing upward on the screw anchor. 5. Disconnect the windshield washer hose at the Y connector at the rear corner of the engine compartment. 6. Lift the cowl grille from the vehicle. 7.
Maintenance and care 8. Remove four (4) screws from the top surface of the cabin air filter top cover. 9. Remove the cover. 10. Remove the filter element by pulling forward on the top surface of the filter and lifting. B 11. Install the new filter (A) element into the filter retaining frame (B). Ensure that you insert the three retaining tabs in the A bottom of the filter frame. 12. Reinstall the filter top cover and the four (4) screws. 13. Reconnect the washer hose. 14.
Maintenance and care 15. Reinstall the four (4) screw anchors and the four (4) plastic screws. 16. Close the hood. 17. Reinstall the six (6) screws in the cowl grille. 18. Reinstall the wiper arms. Ensure that you reinstall the wiper arms in the same position. 19. Push the wiper arm downward onto the wiper arm pivot until the small retaining clip snaps into the locked position. 20. Lower the wiper arm blade onto the windshield surface.
Maintenance and care REAR WINDOW WIPER BLADES Refer to Windshield Wiper Blades in this section for more information on rear wiper blades. INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called Tire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
Maintenance and care The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and care them as indicated in the scheduled maintenance guide. If you notice that the tires wear unevenly, have them checked. • Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity.
Maintenance and care Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow.
Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury.
Maintenance and care • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction.
Maintenance and care 2. Carefully turn the filler cap counterclockwise 1/4 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on the filler pipe. 5. Turn the filler cap clockwise 1/4 of a turn until it stops. If the “Service Engine Soon” indicator comes on and stays on when you start the engine, the fuel filler cap may not be properly installed.
Maintenance and care Octane recommendations Your vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. We do not recommend the use of (R+M)/2 METHOD gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly.
Maintenance and care Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrumentation chapter.
Maintenance and care The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Maintenance and care Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy. • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop.
Maintenance and care Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy. • Using fuel blended with alcohol may lower fuel economy.
Maintenance and care • Have the items listed in your scheduled maintenance guide performed according to the specified schedule. The scheduled maintenance items listed in the scheduled maintenance guide are essential to the life and performance of your vehicle and to its emissions system.
Maintenance and care If the vehicle’s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. To ready the on-board diagnostics system for I/M testing, follow the procedure described below: 1. Allow the engine to cool to ambient temperature (the engine coolant temperature gauge indicator will point to C). 2.
Maintenance and care • Brakelamps • Backup lamps • License plate lamps Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Disconnect the electrical connector from the bulb by pulling rearward. 3.
Maintenance and care 1. With the flat side of the new bulb’s plastic base facing upward, insert the glass end of the bulb into the lamp assembly. Turn the bulb left or right to align the grooves in the plastic base with the tabs in the lamp assembly. When the grooves are aligned, push the bulb into the lamp assembly until the plastic base contacts the rear of the lamp assembly. 2.
Maintenance and care Replacing front turn signal lamp bulbs 1. Remove bulb socket by turning it counterclockwise, then slide it out of the lamp assembly. 2. Carefully pull bulb straight out of the socket and push in the new bulb. 3. To complete installation, follow removal procedure in the reverse order. Replacing high-mount brakelamp bulbs 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb by rotating socket counterclockwise and pulling it out of the lamp assembly. 3.
Maintenance and care Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull the bulb from the socket and push in the new bulb. 4. Install the lamp assembly on liftgate with two grommets, ensuring the grommets are pushed all the way in to the liftgate and secure with two screws. Using the right bulbs Replacement bulbs are specified in the chart below.
Maintenance and care Function Number of Trade number bulbs Turn signal lamps (rear) 2 3156 Tail Lamps 2 3157 Personal reading lamps 2 578 Stepwell lamps 4 194 Glove compartment 1 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.
Maintenance and care Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. After washing, apply the brakes several times to dry them. Underbody Flush the complete underside of vehicle frequently. Keep body drain holes unplugged. Inspect for road damage.
Maintenance and care The brushes used in some automatic car washes may damage the finish on your wheels. Before going to a car wash, find out if the brushes are abrasive. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary. Do not clean plastic parts with thinners, solvents or petroleum-based cleaners. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergent and water.
Maintenance and care • Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaning the steering wheel or instrument panel to avoid contamination of the air bag system.
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, tears or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Engine air filter element Cabin air filter Fuel filter Battery Oil filter PCV Valve Spark plugs 1 3.3L V6 engine FA-1121 FP-27 FG-993 BXT-24-F FL-2007 EV-217 AGSP-32FP 1 Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Capacities and specifications LUBRICANT SPECIFICATIONS Item Brake fluid Door weatherstrips Engine coolant Engine oil Ford part name High Performance DOT 3 Motor Vehicle Brake Fluid Silicone Lubricant Ford Premium Engine Coolant (green colored) Motorcraft SAE 5W-30 Super Premium Motor Oil Door latch, hood Multi-Purpose latch, auxiliary Grease hood latch, door and liftgate hinges, striker plates, seat tracks, fuel filler door hinge.
Capacities and specifications Item Disc brake caliper rails Constant velocity joints Windshield washer fluid Ford part name Silicone Brake Caliper Grease and Dielectric Compound CV Joint Grease (High Temp.) Ultra-clear Windshield Washer Concentrate Ford part Ford number specification D7AZ-19A331-A ESE-M1C171-A (Motorcraft WA-10) E43Z-19590-A ESP-M1C207-A C9AZ-19550-AC ESR-M17P5-A ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system1 Compression ratio 3.
Capacities and specifications 3 5 2 4 1 235
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Customer assistance Ford Extended Service Plan You can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada).
Customer assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern cannot be resolved at the dealership level, please contact the Ford Customer Relationship Center.
Customer assistance If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O.
Customer assistance replacement or repurchase remedies provided by certain state laws. This dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S.
Customer assistance Concerns are ineligible for review if the New Vehicle Limited Warranty has expired at receipt of your application and, in certain states eligibility is dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the unique brochures for California, West Virginia, Georgia and Wisconsin purchasers/lessees.
Customer assistance • a brief summary of the action taken by the dealer(s) and Ford Motor Company • the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does not qualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application.
Customer assistance You may also contact the North American Customer Relationship Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Relationship Center 16800 Executive Plaza Drive P.O.
Customer assistance The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficulty importing your vehicle back into the U.S.
Customer assistance Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength Tar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car Wash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super Premium Tire and Trim Dressing Ford Triple Clean Ford Ultra-Clear Spray Glass Cleaner (not a
Customer assistance Comfort and convenience Cargo nets Cargo organizer Cargo tray Electrochromic inside mirror with compass display Electrochromic inside mirror with compass and temperature display Engine block heater Seatback organizer Tire step Travel equipment Ash cup Auto headlamps with daytime running lights (DRL) Cigarette lighter element Console Daytime running lights (DRL) Framed luggage covers Heavy-duty battery HomeLinkt (in sun visor) Molded running boards Rear view mirror with HomeLinkt Rear vie
Customer assistance Protection and appearance equipment Air bag anti-theft locks Carpet floor mats Cleaners, waxes and polishes Door edge guards Flat splash guards Front end covers (full and mini) Hood deflectors Lubricants and oils Molded splash guards Molded vinyl floor mats Park aid system Rear air deflectors Side window air deflectors Touch-up paint Underbody security lighting Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipmen
Customer assistance cause the engine to stumble or stall or cause the transmission to be damaged or operate improperly. In addition, such systems may be damaged or their performance may be affected by operating your vehicle. (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect your vehicle’s operation.) • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index A B Accessory delay ..........................91 Air bag supplemental restraint system ................131–132 and child safety seats ............133 description ..............................132 disposal ....................................136 driver air bag ..........................134 indicator light .....................8, 135 operation .................................134 passenger air bag ...................134 Air cleaner filter ...............200, 232 Air conditioning ......................
Index built-in child seat ...................231 engine compartment ..............228 exterior ....................................227 exterior lamps .........................228 instrument cluster lens ..........230 instrument panel ....................230 interior .............................230–231 mirrors .....................................228 plastic parts ............................228 safety belts ..............................231 washing ....................................226 waxing ...........
Index Engine block heater .................150 Engine oil ..................................189 checking and adding ..............189 dipstick ....................................189 filter, specifications ........191, 232 recommendations ...................191 refill capacities ........................232 specifications ..................233–234 Exhaust fumes ..........................151 F Floor mats .................................100 Fluid capacities .........................232 Foglamps ..............
Index Heating ........................................24 heating and air conditioning system .................24 HomeLink universal transceiver (see Garage door opener) ............94–97 Hood ..........................................187 I Ignition .................................82, 234 Infant seats (see Safety seats) .....................137 Inspection/maintenance (I/M) testing ..............................220 Instrument panel cleaning ...................................230 cluster .....................
Index M Message center .....................18–19 Mirrors .........................................98 cleaning ...................................228 heated ........................................94 side view mirrors (power) .......93 Moon roof ....................................99 Motorcraft parts ................216, 232 O Octane rating ............................215 Odometer .....................................15 Oil (see Engine oil) ..................189 Overdrive .............................
Index jump starting ..........................179 Steering wheel controls ......................................86 tilting .........................................90 T Tachometer .................................14 Tires ...........................175, 208–209 changing ..........................175, 177 checking the pressure ............209 replacing ..................................210 rotating ....................................209 snow tires and chains ............211 tire grades .....................
Filling station information Item Required fuel Fuel tank capacity Engine oil capacity (includes filter change) Tire size and pressure Hood release Coolant capacity1 Power steering fluid capacity Automatic transmission fluid capacity 2 Information Unleaded fuel only - 87 octane 75.7L (20.0 gallons) 4.0L (4.2 quarts). Use Motorcraft SAE 5W-30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. Refer to the Certification Label on inside of driver’s door.
