Contents Before driving Introduction 2 Instrumentation 4 Controls and features 16 Seating and safety restraints 62 Starting and driving Starting 94 Driving 100 Roadside emergencies 135 Servicing Maintenance and care 154 Capacities and specifications 204 Reporting safety defects 212 Index 213 All rights reserved.
Introduction ICONS Indicates a warning. Read the following section on Warnings for a full explanation. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment.
Introduction contents without notice and without incurring obligation. SPECIAL NOTICES Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of control or an accident. Be sure to read Driving off road in the Driving chapter as well as the “Four Wheeling” supplement included with 4WD and utility type vehicles.
Instrumentation Instrument cluster (pg. 6) Speed control (pg. 26) 4 H C 5 2 50 60 70 o o o o 40 UNLEADED FUEL ONLY 1 0 F 6 3 40 20 80 100 120 80 140 60 30 0 0 0 0 0 0 20 10 H 90 160 100 180 110 H 200 E RSM OFF ON SET ACC OFF COAST SRS Headlamp control (pg. 16) Instrument panel dimmer switch (pg. 17) 4 Tilt steering wheel lever (pg. 31) Turn signal and wiper/washer control (pg. 25) Driver side air bag (pg.
Instrumentation Gearshift (includes overdrive button) (pg. 104) Electronic sound system; refer to Audio Guide Rear window/washer control (pg. 32) Rear window defroster control (pg. 24) OD ON/OFF VOL – PUSH ON SEEK TUNE DISCS SCAN FF 2 REW 1 CLK FM 1 AM FM BASS TREB BAL FADE AUTO SET PUSH TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 4 COMP 5 SHUFFLE 6 OFF LO HI Climate controls (pg. 18) Foglamp control (if equipped) (pg.
Instrumentation WARNING LIGHTS AND CHIMES DOOR AJAR CHECK GAGE 4 3 H CHECK ENGINE 5 6 C F E ABS 20 10 0 80 0 0 0 100 ! P 40 90 120 140 000000 20 MPH R N D 2 1 160 100 180 110 km/h 120 H SPEED CONT L 4WD HIGH H THEFT BRAKE Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II).
Instrumentation What you should do if the check engine light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Check Engine light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securely tightened.
Instrumentation have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Fuel reset Illuminates when the ignition key is turned to the ON position and the fuel pump shut-off switch has been triggered. For more information, refer to Fuel pump shut-off switch in the Roadside emergencies chapter.
Instrumentation Brake system warning Momentarily illuminates when the ignition is turned ONand the engine is off. Also illuminates when the parking brake is engaged. Illumination after releasing the parking brake indicates low brake fluid level. ! BRAKE Anti-lock brake system (ABS) Momentarily illuminates when the ignition is turned on and the engine is off. If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately.
Instrumentation Anti-theft system (if equipped) Refer to Anti-theft system in the Controls and features chapter. THEFT Charging system Momentarily illuminates when the ignition is turned ON and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Check gage Illuminates when the key is in the ON position and the engine coolant temperature is high, the engine oil pressure is low or the fuel level is near empty.
Instrumentation O/D off (if equipped) Illuminates when the transmission control switch has been pushed. When the light is on, the transmission does not shift into overdrive. If the light does not come on when the transmission control switch is depressed or if the light flashes when you are driving, have your vehicle serviced. O/D OFF Speed control This light comes on when either the SET/ACCEL or RESUME controls are pressed.
Instrumentation Key-in-ignition warning chime Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened. Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.
Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle, switch off the ignition and let the engine cool. Refer to Engine coolant in the Maintenance and care chapter. H C Never remove the coolant recovery cap while the engine is running or hot.
Instrumentation Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. 50 40 60 70 80 0 0 0 80 100 60 30 20 10 90 120 140 000000 40 160 100 180 20 110 km/h 120 MPH Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine. 4 3 5 6 RPMx1000 2 1 0 Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position.
Instrumentation Engine oil pressure gauge This shows the engine oil pressure in the system. Sufficient pressure exists as long as the needle remains in the normal range (the area between the “H” and “L”). If the gauge indicates low pressure, switch off the engine immediately. Check the oil level. Add oil if needed (refer to Checking and adding engine oil in the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician.
Controls and features HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps only. Rotate to the second position to also turn on the headlamps. Foglamp control (if equipped) Turn on the low-beam headlamps and press the foglamp control to activate the foglamps. The foglamp control button will illuminate when the foglamps are on. Press the foglamp control a second time to deactivate the foglamps.
Controls and features High beams Push forward to activate. Flash to pass Pull back to activate and release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Rotate up to brighten. • Rotate down to dim. Use to control the dome lamps. • Rotate all the way up to turn on. • Rotate all the way down to override.
Controls and features CLIMATE CONTROL SYSTEM Manual heating and air conditioning system OFF A/C MAX A/C Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control OFF A/C Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor will operate in all modes except and .
Controls and features while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster.
Controls and features • (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Controls and features hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the temperature is about 10°C (50°F) or higher, the air conditioner will automatically dehumidify the air to prevent fogging. -Distributes outside air • through the windshield defroster ducts. It can be used to clear ice or fog from the windshield.
Controls and features • Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the vehicle. Then operate your air conditioner as you would normally.
Controls and features Rear console climate controls (if equipped) Depending on the equipment package of your vehicle, the rear console may not be equipped with rear console audio/climate controls. Turn the air distribution control to the desired airflow position. - VOLUME + MODE SEEK MEMORY The instrument panel climate controls must be on in order for the rear climate control console controls to work. Turn the fan speed control to the desired position.
Controls and features Select for air to flow through these vents: – VOLUME SEEK REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. • The small LED will illuminate when the defroster is activated. The ignition must be in the ON position to operate the rear window defroster. The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position.
Controls and features 4WD CONTROL (IF EQUIPPED) This control operates the 4WD. Refer to Four-wheel drive (4WD) operation in the Driving chapter for more information. AUTO HIGH LOW AUDIO SYSTEM Refer to the “Audio Guide” in your owner portfolio. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal.
Controls and features SPEED CONTROL To turn speed control on • Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph). ON OFF Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. To turn speed control off • Press OFF or • Turn off the vehicle ignition.
Controls and features To set a speed • Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). RSM SET ACC COAST If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill.
Controls and features To set a higher set speed • Press and hold SET ACC/SET ACCEL. Release the control when the desired vehicle speed is reached or • Press and release SET ACC/SET ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal, then press and release SET ACC/SET ACCEL. You can accelerate with the accelerator pedal at any time during speed control usage.
Controls and features • Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC/SET ACCEL. RSM SET ACC COAST To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Controls and features To return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). RSM SET ACC COAST Indicator light This light comes on when either the SET ACC/SET ACCEL or RES/RSM/RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position.
Controls and features TILT STEERING Pull the steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control to lock the steering wheel in position. Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside emergencies chapter.
Controls and features WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals. Push the control on the end of the stalk to activate washer. Push and hold for a longer wash cycle.
Controls and features OFF Press the control for rear washer fluid operation. R.WIPE HI PUSH OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according to your option package. All overhead consoles show the outside temperature and compass display. Storage compartment (if equipped) N OPE P LAM Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open.
Controls and features • Remove the storage clip from the door. • Place Velcroy hook onto side of aftermarket transmitter opposite of actuator control. • Place the transmitter into storage compartment, control down. • Place the provided height adaptors onto the back of the GARAGE control as needed. • Press the GARAGE control to activate the transmitter. Moon roof (if equipped) • Press and release the rear portion of the moon roof control to open.
Controls and features The moon roof has a sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle. Do not let children play with the moon roof. They may seriously hurt themselves. Electronic compass/temperature display A compass and outside temperature display are contained in the overhead console. The compass and temperature display can be turned off and on by pressing the MODE control on the overhead console.
Controls and features OPEN The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in or on the vehicle may also affect compass accuracy. Adjustments may need to be made to the zone and calibration of the compass. GARAGE LAMP MODE 73° LAMP NW Compass zone adjustment 1. Determine which magnetic zone you are in by referring to the zone map.
Controls and features 2. Press and hold the MODE control until VAR appears in the display, then release. The display should show the current zone number. 3. Press the MODE control until the desired zone number appears. The display will flash and then return to normal operation. The zone is now updated.
Controls and features Setting autolamp OFF 1. Make sure the headlamp control is in the OFF position. Leaving the headlamp control on will override the autolamp. 2. Turn the ignition to the ON position or start the vehicle. 3. Slide the delay control all the way to the left. The further you move the knob to the right, the longer the headlamps stay on after the ignition is turned to the OFF position. The autolamp will keep the headlamps on for a maximum of three minutes after the ignition is turned to OFF.
Controls and features whenever the vehicle is placed in R (Reverse) (when the mirror is in the ON position). This helps to ensure a bright clear view in the mirror when backing up. POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open.
Controls and features One touch down • Press AUTO and release quickly. The window will open fully. Depress again to stop window operation. AUTO Window lock The window lock feature allows only the driver to operate the power windows. WINDOW LOCK POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. U Two step unlocking (if equipped) When unlocking the driver door with the key, turn it once toward the rear of the vehicle to unlock that door only.
Controls and features If the vehicle is equipped with the optional perimeter alarm system, this feature will work from all doors. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors.
Controls and features 3. Return to the center position to lock mirrors in place. CENTER CONSOLE Your vehicle may be equipped with a variety of console features. These include: • utility compartment with cassette/compact disc storage • auxiliary power point • cupholders • tissue box holder • cellular phone (if equipped) • ashtray or removable ashcup • compact disc changer (if equipped) Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Controls and features POSITIVE RETENTION FLOOR MAT Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure. REAR LIFTGATE The liftgate area is only intended for cargo, not passengers. You can open and close the liftgate from outside the vehicle.
Controls and features damage may occur to the liftgate door lift cylinders and attaching hardware. Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle.
Controls and features Do not place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. Rewinding the shade With extended use, the cargo shade may lose its spring tension. If this occurs, the shade must be manually rewound. This is a two-person operation. 1. Remove the shade from the vehicle and extend it with the smooth grain facing you. 2. Wrap the vinyl around the roller tube twice.
Controls and features 5. Let go of the right end cap. The clutch will now engage and stop the shade from losing its spring tension. 6. Unfold the vinyl and place it into the end cap slots. 7. Insert the shade into the side mounting brackets and check to make sure that it operates properly. REMOTE ENTRY SYSTEM The remote entry system allows you to lock or unlock all vehicle doors without a key. The remote entry features only operate with the ignition in the OFF position.
Controls and features Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps, reminding you to properly close all doors. Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON.
Controls and features Replacing the battery The transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by: • battery weakness due to time and use • weather conditions • nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1.
Controls and features Replacing lost transmitters Take all your vehicle’s transmitters to your dealer for reprogramming if: • a transmitter is lost or • you want to purchase additional transmitters (up to four may be programmed). To reprogram the transmitters, place the key in the ignition and switch from OFF to ON five times in rapid succession (within 10 seconds). After doors lock/unlock, press any button on all transmitters (up to four). When completed, switch the ignition to OFF.
Controls and features door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignition is turned to the START or ACC position. The dome lamp switch (if equipped) must not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. Battery saver will shut off the interior lamps 45 minutes after the last door is closed.
Controls and features that the anti-theft system is not armed, the ignition is OFF and all vehicle doors and liftgate window are closed. 1. Enter the 5 digit entry code. 2. Press and release the 3/4 control while holding the 7/8 control. 3. Release the 7/8 control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. To reactivate autolock, repeat steps 1 through 4.
Controls and features 6. Press the power door unlock switch. The horn will chirp once upon successful toggling of the Autolock feature. 7. Turn ignition to OFF. The horn will chirp to confirm procedure is complete.
Controls and features Programming your own personal entry code 1. Enter the factory-set code (keypad will illuminate when pressed). 2. Press the 1/2 control within five seconds of step 1. 3. Enter your personal 5 digit code. Enter each digit within five seconds of the previous one. 1 2 3 4 5 6 7 8 9 0 Do not set a code that includes five of the same number or presents them in sequential order. Thieves can easily figure out these types of codes.
Controls and features Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds of step one. 3. Press the 7/8 and 9/0 controls at the same time within five seconds of step two. The system will now only respond to the factory-set code.
Controls and features Operating your perimeter alarm system (if equipped) from the keyless entry pad The keyless entry system arms by pressing 7/8 and 9/0. To disarm or reset a triggered alarm, enter the five digit code. All doors must be fully closed for the alarm system to arm. Refer to the Perimeter alarm system section, if equipped, in this chapter for more details.
Controls and features • Pressing 7/8 and 9/0 on the keyless entry pad at the same time to lock the doors (doors opened or closed). If a door is open, the system is prearmed and is waiting for the door to close. The theft indicator on the instrument cluster will be lit continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds. When you press the lock control twice within 5 seconds, the horn will chirp once to let you know that the system is armed.
Controls and features • Unlock the doors by using your remote entry transmitter. • Unlock the doors with a key. Turn the key full travel (toward the front of the vehicle) to make sure the alarm disarms. • Unlock the doors by using your keyless entry keypad. • Turn ignition to ACC or ON. 1 2 3 4 5 6 7 8 9 0 • Press the panic control on the remote entry transmitter. This will disarm the system only if the alarm is sounding.
Controls and features SecuriLocky key is read by the SecuriLocky anti-theft system. If the SecuriLocky key identification code matches the code stored in the SecuriLocky anti-theft system, the vehicle’s engine is allowed to start. If the SecuriLocky key identification code does not match the code stored in the system or if a SecuriLocky key is not detected (vehicle theft situation), the vehicle’s engine will not operate.
Controls and features indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or a qualified technician. Programming spare SecuriLockY keys Spare SecuriLocky keys can be purchased from your dealership and programmed to your SecuriLocky anti-theft system (up to a total of 8 keys). Your dealership can program your new SecuriLocky key(s) to your vehicle or you can do it yourself using the following simple procedure.
Controls and features SecuriLocky keys and the new unprogrammed SecuriLocky key readily accessible for the procedure. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed SecuriLocky key into the ignition switch and turn the ignition from OFF to RUN (maintain ignition in RUN for at least one second). 2. Turn ignition to OFF and remove the first SecuriLocky key from the ignition switch. 3.
Controls and features If the programming procedure was successful, the new SecuriLocky key(s) will start the vehicle’s engine. The theft indicator (located on the instrument cluster) will light for three seconds and then go out. If the programming procedure was not successful, the new SecuriLocky key(s) will not operate the vehicle’s engine. The theft indicator will flash on and off. Wait at least one minute and then repeat the procedure from step 1.
Seating and safety restraints SEATING Head restraints Push or pull the head rests to the desired position. Front seats Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down. Using the power lumbar support The power lumbar control is located on the outboard side of the seat. Press one side of the control to adjust firmness. Press the other side of the control to adjust softness.
Seating and safety restraints REAR SEATS Head restraints Push or pull the head rests to the desired position. Folding rear seats (if equipped) If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. 1. Press the lower release control downward to unlatch the seatback. 2. Rotate the seatback downward into the load floor position. 3. Press down on the top outboard area of the seatback until a click is heard.
Seating and safety restraints To return the seat to the upright position: • Press downward on the upper corner of the seatback and hold. • Pull the release handle upward to unlatch the seat. • Rotate the seatback upward until the seatback latches in the upright position. The seatback will click when it is locked into position. PUSH PUS H SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should always wear their safety belts. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Seating and safety restraints Combination lap and shoulder belts 1. To fasten, insert the tongue into the slot in the buckle. 2. To unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
Seating and safety restraints receives an impact of 8 km/h (5 mph) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is desired.
Seating and safety restraints • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and safety restraints to make sure it is locked in place. Position the shoulder belt height adjuster so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision.
Seating and safety restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition key is turned to ON... Then... The safety belt warning light illuminates for one to two minutes and the warning chime sounds for four to eight seconds. The safety belt warning light turns off. The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding...
Seating and safety restraints Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Maintenance and care section.
Seating and safety restraints Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: • work with the safety belt to protect the driver and right front passenger • reduce certain upper body injuries Failure to follow these instructions will affect the performance of the safety belts and increase the risk of personal injury. The right front passenger air bag is not designed to restrain occupants in the center front seating position.
Seating and safety restraints Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision. Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer.
Seating and safety restraints How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The air bags inflate and deflate rapidly upon activation.
Seating and safety restraints If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: • driver and passenger air bag modules (which include the inflators and air bags), • one or more impact and safing sensors, • a readiness light and tone • and the electrical wiring which connects the components.
Seating and safety restraints A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately.
Seating and safety restraints younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or provincial laws for specific requirements regarding the safety of children in your vehicle. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Seating and safety restraints face or neck, the child should wear the lap and shoulder belt. Moving the child closer to the center of the vehicle may help provide a good shoulder belt fit. If the shoulder belt cannot be properly positioned: • move the child to one of the seats with a lap belt only (if equipped) OR • if the child is the proper size, restrain the child in a safety seat. Do not leave children, unreliable adults, or pets unattended in your vehicle.
Seating and safety restraints edge of the seat cushion. You may wish to discuss the special needs of your child with your pediatrician. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Seating and safety restraints capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps. Carefully follow all of the manufacturer’s instructions included with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision. Installing child safety seats in combination lap and shoulder belt seating positions 1.
Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it.
Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with knee on the child seat. 8.
Seating and safety restraints able to pull more belt out). If the retractor is not locked, unbuckle the belt and repeat steps two through nine. Check to make sure the child seat is properly secured before each use. Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap that goes over the back of the vehicle seat and attaches to an anchoring point. Other manufacturers offer the tether strap as an accessory.
Seating and safety restraints Tighten the anchor according to specifications. Otherwise, the safety seat may not be properly secured and the child may be injured in a sudden stop or collision. BUILT-IN CHILD SEATS Built-in child safety seat (if equipped) The rear seat may include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standard. Read the labels located on the child seat cushion and shoulder belt for information on the built-in child seat.
Seating and safety restraints Placing your child in the built-in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle’s interior during a sudden stop or crash. The second row seatback must be fully locked before operating the child restraint system. Check the position of the seatback release lever. Never use the Built-In Child Seat as a booster cushion with the adult safety belts.
Seating and safety restraints 2. Pull both Velcrot straps to release the child seat cushion. 3. Lower the child seat cushion.
Seating and safety restraints 4. Unfold the cushion protector flap onto adult seat cushion 5. If connected, disconnect the chest clip and buckles. 6.
Seating and safety restraints 7. Insert the left and right safety belt tongues into the left and right slots of the crotch buckle. Verify that the indicator window on each tongue is green to ensure proper safety belt connections. If both tongues do not latch in the buckle, do not use the child seat. See your dealer for repairs. 8. Fasten the right and left chest clip halves together and adjust the clip to comfortably hold the shoulder belts in place over the child’s chest.
Seating and safety restraints 9. Pull on the safety belt tongues to ensure that they are both securely latched. If they are not properly latched, repeat steps seven and eight. If necessary, the shoulder belt may be put in automatic locking mode (ALR) to limit the child’s movement in the seat. The ALR mode should be used if the child is sleeping or attempting to get out of the seat.
Seating and safety restraints Deactivating the automatic locking mode (ALR) on the built-in child safety seat 1. Disconnect the chest clip and remove the left and right safety belt tongues from the crotch buckle. 2. Allow the shoulder belts to fully retract. Removing your child from the built-in child safety seat 1. Disconnect the chest clip by squeezing the release tabs together and pulling the two sides apart. 2. Press the release button on the crotch buckle. 3.
Seating and safety restraints 5. Slide the Velcrot straps through the D-rings on the child seat cushion and attach. 6. Slide the head restraint down until the top of the head restraint is flush with the top of the adult seat back. 7. Press firmly on the top center of the built-in child safety seat head restraint to ensure it is stowed properly. Inspecting the built-in child seat after a collision Inspect all built-in child restraints, including seats, buckles, retractors, seat latches.
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the spark ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accelerator when you have difficulty starting the engine. For more information on starting the vehicle, refer to Starting the engine in this chapter.
Starting Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM).
Starting • Make sure the parking brake is set. • Make sure the gearshift is in P (Park). 3. Turn the key to 4 (ON) without turning the key to 5 (START).
Starting Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light ( ) will not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 4 3 5 2 1 2. If the engine does not start within five seconds, wait ten seconds and try again. 3.
Starting heater-defroster system to respond quickly. They are strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle. Using the heater for longer than three hours will not harm the engine, so the heater can be plugged in the night before starting the vehicle. To prevent electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters.
Starting • the sound of the exhaust system changes • the vehicle has been damaged in a collision Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Driving shudder while braking, felt mainly in the steering wheel, the vehicle most likely needs service. The ABS operates by detecting the onset of wheel lock up during brake applications and compensating for this tendency. The front wheels are prevented from locking even when the brakes are firmly applied. The accompanying illustration depicts the advantage of an ABS equipped vehicle (on bottom) to a non-ABS equipped vehicle (on top) during hard braking.
Driving there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a controlled stop. • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops.
Driving your vehicle in an emergency. Since the parking brake applies only the rear brakes, the vehicle’s stopping distance will be adversely affected. Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy.
Driving The air suspension shut-off switch is located in the cargo area behind the left rear quarter trim panel. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Normal vehicle operation does not require any action by the driver.
Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears in a steady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park).
Driving P (Park) Always come to a complete stop before shifting into P (Park). Make sure the gearshift is securely latched in P (Park). R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy.
Driving transmission control switch on the end of the gearshift lever with the gearshift in the position. The TCIL will illuminate on the instrument cluster. Transmission operates in gears one through (Drive) provides more three. engine braking than (Overdrive) and is useful when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired. If towing a trailer, refer to Driving while you tow in the Towing a trailer chapter.
Driving 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed. Driving with a 5–speed automatic transmission (4.0L engines only) Understanding gearshift positions Hold the brake pedal down while you move the gearshift lever from position to position.
Driving R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear. (Overdrive) The normal driving position for the best fuel economy. Transmission operates in gears one through five.
Driving braking than (Overdrive) and is useful whenever driving conditions (i.e., city traffic, hilly terrain, etc.) cause the transmission to excessively shift between (Overdrive) and (Drive). (Overdrive) Also deactivate when: • driving with a heavy load • towing a trailer up or down steep hills • additional engine braking is desired. (Overdrive) mode, To return to press the transmission control switch. The TCIL will no longer be illuminated.
Driving the vehicle decelerates to the proper vehicle speed. CONTROL-TRAC AUTOMATIC FOUR-WHEEL DRIVE SYSTEM (IF EQUIPPED) The 4WD system uses all four wheels to power the vehicle. This increases traction, enabling you to drive your 4x4 over terrain and road conditions not normally traveled by two-wheel drive vehicles. Power is supplied to all four wheels through a transfer case that allows you to select a four-wheel drive mode best suited for your current driving conditions.
Driving • The 4WD HIGH mode provides four-wheel drive with full power to both axles. It is only intended for severe winter or off-road conditions, such as deep snow and ice (where no dry or wet pavement remains uncovered), and shallow sand. AUTO HIGH LOW • The 4WD LOW mode supplies four-wheel drive with full power to both axles and includes a lower gear ratio for low-speed.
Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles. Using the Control-Trac system Shifting between 4WD AUTO and 4WD HIGH When you move the control to 4WD HIGH, the indicator light will illuminate in the instrument cluster.
Driving Shifting from 4WD LOW to 4WD AUTO or 4WD HIGH 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission). 4. Move the 4WD control to the 4WD AUTO or 4WD HIGH position. Driving off-road with 4WD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road.
Driving If your vehicle gets stuck If the vehicle is stuck, shift the transmission in a steady motion between forward and reverse gears. Allow the transmission to engage, then press lightly on the accelerator. Do not rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander.
Driving Once through water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes. Drying can be improved by moving your vehicle slowly while applying light pressure on the brake pedal. After driving through mud, clean off residue stuck to rotating driveshafts and tires. Excess mud stuck on tires and rotating driveshafts causes an imbalance that could damage drive components.
Driving hill before driving over the crest. When climbing a steep hill, start in a lower gear rather than downshifting to a lower gear from a higher gear once the ascent has started. This reduces strain on the engine and the possibility of stalling. When descending a steep hill, avoid sudden braking. Rapid pumping of the brake pedal will help slow the vehicle and still maintain steering control.
Driving Avoid sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. When braking, apply the brakes as you normally would. In order to allow the anti-lock brake system (ABS) to operate properly, keep steady pressure on the brake pedal. Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) (5.
Driving Driving off-road with AWD Your vehicle is specially equipped for driving on sand, snow, mud and rough terrain and has operating characteristics that are somewhat different from conventional vehicles, both on and off the road. Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes.
Driving Do not spin the wheels at over 56 km/h (35 mph). The tires may fail and injure a passenger or bystander. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels. Mud and water If you must drive through high water, drive slowly. Traction or brake capability may be limited.
Driving If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. Water intrusion into the transmission may damage the transmission. If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if necessary. The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle.
Driving When speed control is on and you are driving uphill, your vehicle speed may drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph), the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button (to resume speeds over 50 km/h (30 mph). Automatic transmissions may shift frequently while driving up steep grades.
Driving TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the Traction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a Traction-Lok rear axle could result in a permanent reduction in effectiveness. This loss of effectiveness does not affect normal driving and should not be noticeable to the driver.
Driving • GVW (Gross Vehicle Weight): Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross Vehicle Weight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo. The GVWR is specific to each vehicle and is listed on the Safety Compliance Label on the driver’s door pillar. • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system.
Driving loaded vehicle (including passengers and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight.
Driving maximum GCWR for your type engine and rear axle ratio. 3. Weigh your vehicle as you customarily operate the vehicle without cargo. To obtain correct weights, try taking your vehicle to a shipping company or an inspection station for trucks. 4. Subtract your loaded vehicle weight from the maximum GCWR on the following charts. This is the maximum trailer weight your vehicle can tow and must fall below the maximum shown under maximum trailer weight on the chart.
Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle’s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing.
Driving this chapter. Remember to figure in the tongue load of your loaded vehicle when figuring the total weight. Trailer towing table (Automatic transmission) GCWR (Gross Combined Weight Rating)/Trailer Weights Trailer Weight Maximum Rear Maximum Range-kg frontal area of Engine axle GCWR-kg (lbs.) trailer-m ratio (lbs.) 0-Maximum (ft) 4.0L 4 082 0-2 041 3.55 4.64 (50) SOHC (9 000) (0-4 500) 4.0L 4 535 0-2 558 3.73 4.64 (50) SOHC (10 000) (0-5 640) 4.0L 4 535 0-2 558 4.10 4.
Driving Trailer towing table (4x4 and AWD with automatic transmission) Notes: For high altitude operation, reduce GCW by 2% per 300 meters (1 000 ft) elevation. For definition of terms and instructions on calculating your vehicle’s load, refer to Vehicle loading in this chapter. Maximum trailer weights shown. The combined weight of the completed towing vehicle and the loaded trailer must not exceed the GCWR. Towing a trailer over 907 kg (2 000 lbs.) requires a weight distributing hitch.
Driving to 15% of the total weight of the trailer is on the tongue. Use a frame-mounted weight distributing hitch for trailers over 907 kg (2 000 lb). Safety chains Always connect the trailer’s safety chains to the vehicle. To connect the trailer’s safety chains, cross the chains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agency gives to you.
Driving for hooking up trailer lamps. Using a step bumper The rear bumper is equipped with an integral hitch and requires only a ball with a 19 mm (3/4 inch) shank diameter. The bumper has a 1 590 kg (3 500 lb.) trailer weight and 159 kg (350 lb.) tongue weight capability. Use a frame-mounted weight distributing hitch for trailers over 1 590 kg (3 500 lb). Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer.
Driving Trailer towing tips • Practice turning, stopping and backing up in an area before starting on a trip to get the feel of the vehicle trailer combination. When turning, make wider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 10–15% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts.
Driving • Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions and reliability. If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if necessary. The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle.
Driving To adjust cross-bar position: 1. Slide the locking switches at each end of the crossbar toward the rear of the vehicle until UNLOCKED appears. 2. Slide cross-bar to the desired location. 3. Lock the cross-bar into position by pushing the locking switches on each end of the crossbar toward the front of the vehicle. The rear rack can be completely removed in the UNLOCKED position by sliding the cross-bar rearward until it frees the guides.
Roadside emergencies HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on top of the steering column. • Depress hazard lights control to activate all hazard flashers simultaneously. • Depress control again to turn the flashers off.
Roadside emergencies seconds and return the key to the OFF position. 5. Make a further check for leaks in the fuel system. The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components.
Roadside emergencies Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color Fuse rating 5 amp 7.
Roadside emergencies Passenger compartment fuse panel The fuse panel is located on the left hand side of the instrument panel facing the driver’s side door. Pull the panel cover outward to access the fuses. 28 24 20 16 12 8 4 To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Roadside emergencies The fuses are coded as follows. Fuse/Relay Location 1 2 Fuse Amp Rating 7.5A 7.5A 3 4 5 6 7.5A 10A 10A 7.5A 7 8 7.5A 10A 9 10 7.5A 7.5A 11 7.
Roadside emergencies Fuse/Relay Location 14 Fuse Amp Rating 10A 15 16 7.5A 30A 17 18 7.5A 15A 19 20 25A 7.5A 21 22 23 24 25 15A 20A 15A 7.5A 26 10A 27 15A 28 7.
Roadside emergencies Fuse/Relay Location 30 31 32 33 Fuse Amp Rating 15A — 10A 15A 34 35 36 7.5A 10A 7.5A Description Park Lamp/Trailer Tow Relay NOT USED Rear Blower Headlamps, Daytime Running Lamps (DRL) Module, Instrument Cluster Rear Integrated Control Panel, CD RABS Test Connector CD, Rear Integrated Control Panel, Memory Seat, Message Center Power distribution box The power distribution box is located in the engine compartment near the battery.
Roadside emergencies BLOWER MOTOR RELAY STARTER RELAY FOG LAMP RELAY WASH PUMP RELAY HORN RELAY FUEL PUMP RELAY PCM POWER RELAY WIPER HI/LO RELAY 15 WIPER PARK RELAY 3 2 A/C RELAY 1 13 8 3 4 10 7 8 9 2 6 14 6 7 1 5 9 11 12 5 4 3 10 2 1 Always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. The high-current fuses are coded as follows.
Roadside emergencies Fuse/Relay Location Fuse Amp Rating 7 8 — 20A** 9 10 1 2 3 4 40A** 30A** 10A* 20A* – 15A* 5 6 7 10A* 10A* 30A* 8 9 30A* 20A* 10 11 15A* 15A* 12 30A* 13 15A* 14 30A* Wiper Park Relay — Wiper HI/LO — Relay Description NOT USED Automatic Ride Control ARC Switch Off/On Switch Automatic Ride Control Relay PCM Power Relay A/C Relay Auxiliary Power Point Not Used Fog Lamps and Daytime Running Lamps Air Bag Diagnostic Monitor Powertrain Control Module 4 Wheel Anti-Lock System (
Roadside emergencies Fuse/Relay Fuse Amp Description Location Rating PCM Power — PCM Power Relay Relay Fuel Pump Relay — Fuel Pump Relay Horn Relay — Horn Relay Washer Pump — Washer Pump Relay Relay Fog Lamp Relay — Fog Lamp Relay Starter Relay — Starter Relay Blower Motor — Blower Motor Relay Relay 1 Resistor Fuse [7ca] 2 Diode Anti-Lock Brakes Indicator 3 Diode Electronic Engine Controls * Mini Fuses ** Maxi Fuses 1 5.
Roadside emergencies a tire could result in damage to driveline components and make the vehicle difficult to control. Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the following locations: Tool Spare tire Jack, lug nut wrench Jack handle Location Under the vehicle, just in front of the rear bumper Left rear quarter panel behind interior trim Behind rear seats, under carpet Removing the spare tire 1. Insert the jack handle into the rear bumper opening.
Roadside emergencies 2. Slide the wheel under the vehicle and install the retainer through the wheel center. 3. Turn the jack handle clockwise until the tire is raised to its original position underneath the vehicle. The jack handle ratchets when the tire is raised to the stowed position. It will not allow you to overtighten. Tire change procedure On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
Roadside emergencies 5. Loosen each wheel lug nut, but do not remove them until the wheel is raised off the ground. 6. Turn OFF the air suspension switch (if equipped). Refer to Air suspension system in the Driving chapter. 7. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Roadside emergencies • Rear • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts, cone side in, until the wheel is snug against the hub. Do not fully tighten the lug nuts until the wheel has been lowered. 10. Lower the wheel by turning the jack handle counterclockwise. 1 11.
Roadside emergencies 12. Stow the flat tire, jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 13. Turn ON the air suspension switch (if equipped). 14. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter.
Roadside emergencies 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure they do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. 5.
Roadside emergencies 5. Make sure that the jump leads are clear of moving parts of the engine. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Jump starting 1. Start the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the vehicle with the discharged battery. 3.
Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. If equipped with air suspension, the air suspension control must be turned to the OFF position. The Ford approved towing procedure is flatbed or wheel lift with dollies. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground.
Roadside emergencies If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a slingbelt towing procedure. When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for proper hook-up and towing procedures for your vehicle.
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your “Warranty Guide” to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications.
Maintenance and care • Keep all lit cigarettes, open flames and other lit material away from the battery and all fuel related parts. If you disconnect the battery, the engine must “relearn” its idle conditions before your vehicle will drive properly, as explained in Battery in this chapter. Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3.
Maintenance and care OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the steering column on the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. Lift the hood until the lift cylinders hold it open. IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.
Maintenance and care 1. Windshield washer fluid reservoir 2. Transmission fluid dipstick 3. Engine oil fill cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Battery 7. Power steering fluid reservoir 8. Air filter assembly 9. Engine coolant reservoir 5.0L engine 2 3 4 5 1 9 8 7 6 1. Engine coolant reservoir 2. Windshield washer fluid reservoir 3. Engine oil fill cap 4. Automatic transmission fluid dipstick 5. Brake fluid reservoir 6.
Maintenance and care 7. Power steering fluid reservoir 8. Engine oil dipstick 9. Air filter assembly ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5.
Maintenance and care • 4.0L engines FULL ADD 1 QT • 5.0L engine MIN MAX 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the ADD and FULL marks (4.0L engines) or between the MIN and MAX marks (5.0L engines) the oil level is acceptable. DO NOT ADD OIL.
Maintenance and care • If the oil level is below the ADD mark (4.0L engines) or MIN mark (5.0L engines), add enough oil to raise the level within the ADD-FULL range (4.0L engines) or MIN-MAX range (5.0L engines). • Oil levels above the letter F in FULL (4.0L engines) or the MAX mark (5.0L engines) may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil.
Maintenance and care Engine oil recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments. They are unnecessary and could, under certain conditions, lead to engine damage which is not covered by your warranty.
Maintenance and care Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, startup engine noises or knock may be experienced. It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application.
Maintenance and care 4. Use only a DOT 3 brake fluid certified to meet Ford specifications. Refer to Lubricant specifications in the Capacities and specifications chapter. Brake fluid is toxic. If you use a brake fluid that is not DOT 3, you will cause permanent damage to your brakes. Do not let the reservoir for the master cylinder run dry. This may cause the brakes to fail. WINDSHIELD WASHER FLUID Checking and adding washer fluid SHER FL WA UID Check the washer fluid whenever you stop for fuel.
Maintenance and care Do not put engine coolant in the container for the windshield washer fluid. ENGINE COOLANT Check the level of the coolant in the reservoir at least once a month. Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked for a long period of time, the engine coolant reservoir may eventually empty. If this occurs, add engine coolant to the coolant reservoir.
Maintenance and care If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. When the engine is cool, add a 50/50 mixture of engine coolant and water to the engine coolant recovery reservoir-DO NOT ADD DIRECTLY TO THE RADIATOR. Add straight water only in an emergency, but you should replace it with a 50/50 mixture of coolant and distilled water as soon as possible. Check the coolant level in the coolant recovery reservoir the next few times you drive the vehicle.
Maintenance and care the cloth to press the cap down, turn it counterclockwise and remove it. Use Ford Premium Cooling System Fluid E2FZ-19549–AA (in Canada, Motorcraft CXC-8–B) or an equivalent premium engine coolant that meets Ford specification ESE-M97B44–A. Ford Premium Engine Coolant is an optimized formula that will protect all metals and rubber elastomers used in Ford cooling systems for four years or 80,000 km (50,000 miles).
Maintenance and care regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, refer to Refill capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you have to add more than a liter (quart) of engine coolant per month.
Maintenance and care • 4.0L SOHC engine DO N OW FLUIDEER ER ST • 5.0L engine 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge will be near the center of the NORMAL band). 2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. 5. If your vehicle is equipped with a 4.0L SOHC engine or a 5.
Maintenance and care lines. Do not add fluid if the level is in this range. 7. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the correct operating range. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the “Service Guide.” Before adding any fluid, make sure the correct type is used.
Maintenance and care fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage. Transmission fluid should be checked at normal operating temperatures 66°C-77°C (150°F-170°F) on a level surface. The normal operating temperature can be reached after approximately 32 km (20 miles) of driving.
Maintenance and care gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 3. Latch the gearshift lever in P (Park) and leave the engine running. 4. Remove the dipstick, wiping it clean with a clean, dry lint free rag. 5. Install the dipstick making sure it is fully seated in the filler tube. 6. Remove the dipstick and inspect the fluid level. The fluid level should be within the top hole area on the dipstick. 7. If necessary, add fluid in .
Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter.
Maintenance and care lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will be necessary. BATTERY Your vehicle may be equipped with a Motorcraft maintenance-free battery. If the original equipment battery needs replacing, it may be replaced with a low-maintenance battery. The low-maintenance battery normally does not require additional water during its life of service.
Maintenance and care If you see any corrosion on the battery or terminals, remove the cables from the terminal(s) and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. Reinstall the cables when you are done cleaning them, and apply a small quantity of grease to the top of each battery terminal to help prevent corrosion. If your battery has a cover/shield, make sure it is reinstalled after the battery is replaced.
Maintenance and care • If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner. Follow your communities standards for disposal. Call your local recycling center to find out more about recycling automotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem less effective.
Maintenance and care turn the ignition to ACC, then turn the wipers on. When the wipers reach the vertical position, turn the ignition to LOCK. To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3.
Maintenance and care Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Maintenance and care The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turning) traction. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Maintenance and care SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the Safety Compliance Certification Label. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control.
Maintenance and care • Four tire rotation • Five tire rotation 180
Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial, bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure that all tires are the same size, speed rating, and load-carrying capacity. Use only the tire combinations recommended on the decal. If you do not follow these precautions, your vehicle may not drive properly and safely.
Maintenance and care Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Maintenance and care • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire.
Maintenance and care Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling. • Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • Fuels can also be harmful if absorbed through the skin.
Maintenance and care law and could damage your vehicle. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese-based compounds containing MMT. Vehicles certified to California emission standards (indicated on the underhood Vehicle Emissions Control Information label) are designed to operate on California reformulated gasolines. If California reformulated gasoline is not available when you refuel, your vehicle can be operated on non-California fuels.
Maintenance and care with the recommended octane, see your dealer or a qualified service technician to prevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hesitation problems try a different brand of fuel. If the condition persists, see your dealer or a qualified service technician. The American Automobile Manufacturers Association (AAMA) issued a gasoline specification to provide information on high quality fuels that optimize the performance of your vehicle.
Maintenance and care Calculating fuel economy To accurately calculate your vehicle’s fuel economy: 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy.
Maintenance and care • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the services listed in your “Service Guide” performed according to the specified schedule. The Scheduled Maintenance Services listed in the “Service Guide” are required because they are considered essential to the life and performance of your vehicle and to its emissions system.
Maintenance and care If you smell exhaust fumes of any kind inside your vehicle, have the dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Do not make any unauthorized changes to your vehicle or engine.
Maintenance and care not pass the I/M test with the “check engine/service engine soon” light on. If the vehicle’s powertrain system or its battery has just been serviced, the OBD-II system is reset to a “not ready for I/M test” condition. To ready the OBD-II system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving on an expressway or highway.
Maintenance and care • license plate lamp • tail lamps • back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect lamp performance. Replacing headlamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Maintenance and care 3. Disconnect the electrical connector from the bulb by pulling the connector rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) about an eighth of a turn to free it from the bulb socket, and by sliding the ring off the plastic base. Keep the ring because it will be used again to retain the new bulb. 5. Remove the old bulb from its socket by gently pulling it straight back out of the socket. Do not turn the bulb while removing it.
Maintenance and care 3. Push the electrical connector into the rear of the plastic base until it snaps, locking it into position. 4. Turn the headlamps on and make sure they work properly. If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again.
Maintenance and care AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant, and vertical and horizontal indicators of the VHAD system are calibrated.
Maintenance and care Horizontal aim adjustment 1. With the hood open, locate the horizontal indicator and adjusting screw. They are located below the viewing hole at the rear of the headlamp assembly. 2. Use a 4mm wrench or socket to turn the horizontal adjusting screw until the “0” mark on the yellow dial lines up with the reference mark on the marker (as shown) when viewed directly from above. Vertical aim adjustment 1. Park the vehicle on a level surface. 2.
Maintenance and care Repeat the above process to the other headlamp, if necessary. CLEANING AND CARING FOR YOUR VEHICLE Refer to the “Customer Assistance Guide” for a list of Ford-approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results.
Maintenance and care Use only carnauba or synthetic-based waxes. Remove any bugs and tar before waxing vehicle. Use cleaning fluid or alcohol with a clean cloth to remove. Use tar remover to remove any tar spots. Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch-up, paint repair foil or aerosol paint spray from the Ford accessory line. Observe the application instructions on the products.
Maintenance and care • 5.0L • 4.
Maintenance and care • 4.0L EFI • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar remover to remove grease and tar. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning.
Maintenance and care Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glass cleaner or tar remover if necessary. To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades If the wiper blades do not wipe properly, clean the windshield and wiper blades with undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water.
Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts. If your vehicle has been involved in an accident, refer to the Safety belt maintenance section in the Seating and safety restraints chapter.
Maintenance and care If the leather cannot be completely cleaned using a mild soap and water solution, the leather may cleaned using a commercially available cleaning product “Tanners Preserve Leather Cleaner” and a 3M “Type T’ scrubbing pad by using the following steps; The type of scrubbing pad is very critical because the common 3M “Scotch Brite” green pad is too aggressive and will damage the leather surface • Spray a small amount of the leather cleaner on the pad and rub the area to be cleaned with the
Maintenance and care with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining. “Tanners Preserve Leather Cleaner” (product number AS-300) is available from “First Brands” by calling 1–800–726–1001. This product may also be available at many local automotive after market stores. 3M “Type T” Clean And Finish Scrubbing Pads (UPC 04011–01276) are available through your local 3M distributor. Call 1–800–742–9649 for the nearest distributor in your area.
Capacities and specifications MOTORCRAFT PART NUMBERS Component 4.0L SOHC engine 5.0L engine Air filter FA-1658 FA-1658 Fuel filter FG-872 FG-872 Battery (standard) BXT-65-650 BXT-65-650 Battery (optional) BXT-65-850 Oil filter FL-1A FL-820S PCV valve EV-225 EV-152 Spark plugs* AGRF-22P AWSF-32EE * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information.
Capacities and specifications Fluid Transmission fluid Transfer case Ford Part Name Motorcraft MERCONtV ATF Motorcraft MERCON t ATF Application 4R70W Automatic with 5.0L engine (AWD) 5R55E Automatic with 4.0L SOHC engine (4x2) 5R55E Automatic with 4.0L SOHC engine (4x4) AWD 4WD Engine coolant Front axle fluid Rear axle fluid1,2,3,4 Ford Premium Cooling System Fluid 4.
Capacities and specifications Fluid Windshield washer fluid 1 Ford Part Name Ultra-Clear Windshield Concentrate Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. 2 Your vehicle’s rear axle is equipped with synthetic rear axle lubricant. Rear axles containing synthetic lubricant are lubricated for life. These lubricants are not to be checked or changed unless a leak is suspected, service required or the axle assembly has been submerged in water.
Capacities and specifications axles, add 118 ml (4 oz.) of additive friction modifier C8AZ-19B546-A, Ford specification EST-M2C118–A, whenever the lubricant is changed. 4 Refer to your “Service Guide” for axle fluid change intervals.
Capacities and specifications Fluid Automatic transmission (4R70W) Automatic transmission (5R55E) Power steering reservoir Ford conventional and traction lok rear axles Front axle Transfer case Transfer case Front Output Slip Shaft 1 Ford part name or equivalent Motorcraft MERCONtV ATF Motorcraft MERCONtV ATF Motorcraft MERCONt ATF Ford part number Ford specification XT-5-QM MERCONtV XT-5-QM MERCONtV XT-2-QDX MERCONt Refer to footnotes 1, 2 and 3 Refer to footnotes 1, 2 and 3 o footnotes 1, 2 an
Capacities and specifications applications must add 118ml (4 oz.) of additive friction modifier C8AZ-19B546–A, Ford specification EST-M2C118–A to the rear axle whenever the axle has been serviced. ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel grade Firing order Spark plug gap Ignition system Compression ratio 5.0L engine 4.0L SOHC engine 302 245 215 @ 4200 rpm 205 @ 5000 rpm 288 lbs.ft. @ 3300 rpm 250 lb. ft. @ 3000 rpm 87 octane 87 Octane 1-3-7-2-6-5-4-8 1-4-2-5-3-6 1.3 mm-1.4 mm 1.
Capacities and specifications 4 1 3 5 2 210
Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label MFD. BY FORD MOTOR CO. IN U.S.A. The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side.
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Air bag supplemental restraint system ..........................................73 and child safety seats ..............75 description ................................74 disposal ......................................78 indicator light ...........................77 passenger air bag .....................76 Air conditioning manual heating and air conditioning system .......18,21,23 Air suspension description ..............................103 All wheel drive (AWD) .............118 Ambulance packages ...
Index improving fuel economy ........134 octane rating ...........................185 quality ......................................186 safety information relating to automotive fuels .....................183 Fuel gauge ...................................15 Fuel pump shut-off switch .......135 Fuse panels instrument panel ....................138 power distribution box ...........141 Fuses ...................................136,137 Gauges, Mechanical ....................12 engine coolant temperature gauge ..
Index replacement/additional transmitters ...............................49 replacing the batteries .............48 Reporting safety defects ..........212 Safety restraints automatic locking mode (retractor) ............................69,70 extension assembly ..................71 for children ...............................78 lap and shoulder belts .............68 maintenance ..............................72 proper use .................................66 warning light and chime ............................
Filling station information Recommended fuel Fuel tank capacity Engine oil capacity (with filter change) Tire size and pressure Hood release Unleaded fuel only - 87 octane 79.5L (20.8 gallons) 4.7L (5.0 quarts). Use Motorcraft 5W30 Super Premium Motor Oil, Ford Specification WSS-M2C153-G See Safety Compliance Certification Label on inside of driver door. Pull handle under the left side of the instrument panel 7.4L (7.8 quarts) 12.1L (12.8 quarts) Fill to line on reservoir or dipstick 13.1L (13.
