Table of contents BEFORE DRIVING Introduction 2 Instrumentation 9 Controls and features 13 Seating and safety restraints 59 STARTING AND DRIVING Starting your vehicle 89 Driving 96 Roadside emergencies 118 SERVICING Maintenance and care 136 Capacities and specifications 185 Reporting safety defects 192 Index 193 Filling station information 200 1
Introduction The following icons appear in this Owner’s Guide: indicates a warning. Read the following section on Warnings for a full explanation of warnings. indicates that vehicle information related to recycling and other environmental concerns will follow. Warnings Warnings remind you to be especially careful in those areas where carelessness can cause damage to your vehicle or personal injury to yourself, your passengers or other people. Please read all Warnings carefully.
Introduction differences for towing, hauling, and off-road operation. For this reason, Mercury urges you to read and understand the contents of the Four-Wheeling supplement. Breaking in your vehicle Your new vehicle goes through an adjustment or breaking-in period during the first 1,000 miles (1,600 km) of driving. During this period: • Change your vehicle’s speed often as you drive. Do not drive at one speed for a long time. • Use only the type of engine oil Ford recommends.
Instrumentation Engine coolant temperature gauge (pg. 7 ) Fuel gauge (pg. 7) Warning lights (pg. 8) Tachometer (pg. 6) Speed control (pg. 23) 4 Hazard flasher control (not shown) (pg. 27) 3 H 2 C 5 0 o o o o 40 RPM x 1000 80 40 10 0 100 120 0 0 0 0 0 0 20 O/D ON/OFF 80 140 60 30 20 P E 50 60 70 6 UNLEADED FUEL ONLY 1 F Engine oil pressure Gearshift gauge (includes (pg. 7) overdrive button) Speedometer (pg. 26) (pg.
Instrumentation Electronic sound system; refer to Audio Guide (premium stereo cassette with CD DJ shown) (pg. 16) Rear wiper/washer Vents control (pg. 15) (pg. 17) Rear window defroster control (pg. 15) VOL – PUSH ON OFF FM 1 AM FM BASS TREB SEEK TUNE DISCS REW 1 SCAN FF 2 R. WIPE HI CLK ST BAL FADE AUTO SET PUSH TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 4 COMP 5 SHUFFLE 6 OFF *A/C *MAX A/C Fog lamp control (pg. 16) Climate controls (pg.
Instrumentation INSTRUMENT CLUSTER Instrument cluster gauges 4 3 H 2 C 5 F E o o o o 40 RPM x 1000 P 80 40 10 0 100 120 80 140 60 30 20 1 0 50 60 70 6 UNLEADED FUEL ONLY 0 0 0 0 0 0 20 H 90 160 L 100 180 110 MPH km/h H 120 - + L R N D 2 1 Speedometer 50 60 70 o o o o 40 30 100 80 80 120 60 140 90 0 0 0 0 0 0 40 20 100 160 20 10 0 MPH 180 km/h Tachometer 4 3 2 5 6 UNLEADED FUEL ONLY 1 0 6 RPM x 1000 110 120
Instrumentation Engine coolant H C Fuel gauge F E Voltage gauge H - + L Oil pressure H L Odometer 50 60 70 40 30 100 120 80 140 90 0 0 0 0 0 0 40 20 o o o o 80 60 160 100 20 10 0 MPH 180 Trip odometer and reset button 110 120 km/h 50 60 70 40 30 100 120 80 140 40 20 o o o o 80 60 90 0 0 0 0 0 0 160 100 20 10 0 MPH 180 km/h 110 120 7
Instrumentation Instrument cluster warning and indicator lights FUEL RESET CHECK GAGE 5 4 3 H - 0 F ABS BRAKE ! RPM x 1000 P E DOOR AJAR illuminates when the ignition key is turned to the ON or START position and a door or liftgate is opened. illuminates when the ignition is turned to ON and the engine temperature is high, the oil pressure is low, or the fuel level is near empty. illuminates when there is a problem with the generator or charging system.
Instrumentation illuminates when the parking brake is activated, brake fluid level is low, or break system requires service. BRAKE ! P illuminates when the headlamp high beams are on. ABS illuminates when the anti-lock brake system requires service. ABS illuminates when the ignition key is turned to ON and the safety belt is not buckled. The light will remain illuminated for one to two minutes or until the safety belt is buckled.
Instrumentation O/D OFF the transmission control indicator light (TCIL) illuminates when the transmission control switch on the end of the gearshift lever is pushed and the D (Overdrive) mode is turned off. O/D OFF indicates the status of the transmission and may flash steadily if a malfunction is detected. If flashing persists, have your transmission serviced by your dealer as soon as possible. If this condition persists, your transmission may be damaged.
Instrumentation How to test the instrument cluster lights CHECK GAGE 4 3 H - 0 F ABS BRAKE ! P o o o o 40 RPM x 1000 P 80 40 10 0 100 120 80 140 60 30 20 + 1 E 50 60 70 6 UNLEADED FUEL ONLY 2 C 5 0 0 0 0 0 0 20 90 160 H L 100 180 110 MPH R N D 2 1 km/h H 120 CHECK ENGINE - + L Turn the ignition key to ON without starting the engine. The warning and indicator lights shown above will illuminate for a brief time.
Instrumentation Headlamps on warning chime A warning chime sounds when the headlamps are on (and key is not in the ignition), the ignition is off, and a door is opened.
Controls and features INSTRUMENT PANEL CONTROLS 4 3 H 2 C 5 50 60 70 6 80 40 100 120 80 140 0 0 0 0 0 0 20 10 0 km/h RPM x 1000 P E 60 30 20 0 o o o o 40 UNLEADED FUEL ONLY 1 F 90 160 100 180 110 120 R N D 2 1 VOL – PUSH ON FM 1 AM FM BASS TREB CLK ST BAL FADE AUTO SET PUSH RSM OFF ON SEEK SET ACC OFF COAST TUNE DISCS SCAN FF 2 REW 1 TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 COMP 5 4 SHUFFLE 6 SRS OFF LO *A/C HI * MAX A/C Headlamp switch This switch operates
Controls and features Daytime running light (DRL) system (if equipped) The daytime running light (DRL) system turns the high beam lamps on, with a reduced light output, when: • The headlamp knob is in the OFF position. • The engine is running. • The parking brake is released. The daytime running light (DRL) system will not illuminate the tail lamps and parking lamps. Turn on your headlamps at dusk. Failure to do so may result in a collision.
Controls and features Liftgate wiper and washer Turn the knob to adjust wiper speed. Push the knob in to activate the washer. OFF R.
Controls and features Foglamps Push the button to activate the foglamps. The indicator light will turn on. The foglamps can be turned on only when the low beam headlamps are on. Push the button again to turn off.
Controls and features Climate controls 5 4 3 H 60 40 160 0 0 0 0 0 0 20 1 0 F 80 100 120 o o o o 140 6 UNLEADED FUEL ONLY 2 C 0 RPM x 1000 P E 180 120 km/h R N D 2 1 VOL – PUSH ON FM 1 AM FM BASS TREB CLK ST BAL FADE AUTO SET PUSH RSM OFF ON SEEK SET ACC OFF COAST SCAN TUNE DISCS FF 2 REW 1 TAPE CD EJ DOLBY SYSTEM SIDE 1-2 3 SHUFFLE 6 COMP 5 4 SRS OFF LO *A/C *MAX A/C HI OFF *A/C *MAX A/C Instrument panel vents There are four vents on the instrument panel.
Controls and features Operating climate controls • Turn the temperature control to the desired temperature. • Turn the fan speed control to the desired speed. • Turn the mode control to the desired airflow position.
Controls and features Controlling airflow Select for air to flow through these vents: The position allows outside air to flow through the instrument panel vents. for air to flow through Select these vents: The position directs outside air to flow between the panel and floor vents. The air conditioning will function provided the outside temperature is above 10°C (50°F). for air to flow through Select these vents: The position directs outside air to flow through the floor vents.
Controls and features Select A/C for air to flow through these vents: The A/C mode directs outside air conditioned air to flow through the instrument panel vents. The A/C mode can be used for heating, ventilating or air conditioning. The A/C mode only functions if the outside temperature is above 10°C (50°F). Select MAX A/C for air to flow through these vents: The MAX A/C mode recirculates the air and directs it to flow through the instrument panel vents.
Controls and features Maximum heating Set mode control to , turn temperature control to maximum heat (red) and set fan speed control to maximum. Maximum cooling Set mode control to MAX A/C, turn temperature control to maximum cool (blue) and set fan speed control to maximum. Ventilating with outside air Set mode control to , turn the temperature control to the desired temperature and turn fan speed control to desired position.
Controls and features STEERING COLUMN CONTROLS 4 3 H 2 C 5 50 60 70 6 F 0 o o o o 40 UNLEADED FUEL ONLY 40 10 0 RPM x 1000 P E 80 100 120 80 140 60 30 20 1 0 0 0 0 0 0 20 H 90 160 L 100 180 110 km/h 120 H R N D 2 1 - + L RSM ON SET ACC OFF COAST SRS Positions of the ignition ACCESSORY allows electrical accessories such as radio and wipers/washer to operate while the engine is not running. LOCK locks the steering wheel and gearshift lever.
Controls and features Speed control Do not shift the transmission into N with the speed control on. Speed control maintains vehicle speed automatically at or above 48km/h (30 mph) using the control switches. Press ON to turn speed control on. SPEED CONT will illuminate in the instrument cluster. Press OFF to turn speed control off. When turned off, the previously programmed set speed will be erased.
Controls and features Press SET ACCEL (with speed control turned ON) to set speed. Hold SET ACCEL to increase speed. Press and release once to increase speed in 1.6 km/h (1 mph) increments. Press COAST to decrease speed. Press RSM to resume speed. Depressing the brake pedal will cancel the speed control.
Controls and features Activating high beams Push the lever forward to activate the high beam lamps. Pull the lever towards you to activate the “flash to pass” function. Push the lever down to activate the left turn signal. Push the lever up to activate the right turn signal.
Controls and features Overdrive control Activating overdrive Overdrive D is the normal drive position for the best fuel economy and will remain on until overdrive is deactivated. The overdrive function allows automatic upshifts to 2nd, 3rd, and 4th gear. Deactivating overdrive Press the transmission control switch on the end of the gearshift lever. The transmission control indicator light (TCIL) O/D OFF will illuminate on the instrument cluster. Transmission will operate in gears 1-3.
Controls and features Hazard flasher Push the hazard flasher button. The button will pop out and the lamps will begin to flash. To stop the flashers, push the flasher button again. 4 5 6 50 60 70 UNLEADED FUEL ONLY 2 80 40 0 P E 80 120 140 H 90 160 0 0 0 0 0 0 L 100 180 20 110 10 0 RPM x 1000 100 60 30 20 1 F o o o o 40 3 H C 120 km/h H - + R N D 2 1 L RSM ON SET ACC OFF COAST SRS Tilt steering Never adjust the steering column while the vehicle is moving.
Controls and features OVERHEAD CONTROLS Overhead console (if equipped) The console includes: • compass/temperature display • map lamps • storage compartment • garage door opener actuator • moon roof control (if equipped) OPEN GARAGE LAMP 28 MODE LAMP
Controls and features Compass/temperature display Press the MODE button (with the ignition key in the ON position) to switch between the following features: • display off • temperature in C (Celsius) and compass • temperature in F (Farenheit) and compass OPEN GARAGE LAMP 73° MODE LAMP NW If the outside temperature is below 4°C (39°F), the word ICE will flash alternately with the temperature for one minute.
Controls and features Compass zone adjustment 1 15 2 14 3 13 4 12 11 5 6 10 7 1. Determine which zone of the country you live in by referring to the zone map. 2. Press and hold the MODE button until VAR appears in the display; then release. The display will show the current zone number. 3. Press the MODE button until the desired zone number appears. Wait three seconds. The display will flash and then return to normal operation. Zone is now updated.
Controls and features 1. Press and hold the MODE button until CAL appears in the display (approximately eight seconds); then release. 2. Drive the vehicle slowly (less than 5 km/h/3 mph) in circles until the CAL indicator turns off (2-3 complete circles). LAMP MODE LAMP CAL Map lamps Press either the driver or passenger button to turn map lamps on or off. OPEN GARAGE LAMP Storage compartment (if equipped) Press the OPEN button to open the storage compartment.
Controls and features 1. Remove storage clip from door. 2. Place Velcro™ hook onto side of aftermarket transmitter opposite of actuator button. 3. Place transmitter into storage compartment, button down. 4. Place the provided height adapters onto the back side of the GARAGE button as needed. 5. Press the GARAGE button to activate the transmitter.
Controls and features Moon roof (if equipped) Press and hold bottom portion of moon roof switch to open. Press and hold top portion of moon roof switch to close. To raise the rear of the moon roof, close the moon roof and press top of rocker switch again. Press bottom of rocker switch to close it. LAMP MODE LAMP Autolamp delay system and automatic dimming mirror (if equipped) Autolamp The autolamp sets the headlamps to turn on and off automatically.
Controls and features 3. Slide the delay slide knob to the center of travel. The further you move the knob to the right, the longer the headlamps stay on after the ignition is turned to the OFF position. The autolamp will keep the headlamps on for a maximum of three minutes after the ignition is turned off. 4. The autolamp automatically turns the lamps on and off. Automatic dimming feature The autolamp/automatic dimming mirror is equipped with an automatic dimming feature.
Controls and features DOOR MOUNTED CONTROLS Power windows Driver side control Press and hold rocker switch to close driver window. Press and release rocker switch for partial window movement. The driver side power window has a one touch down feature. When the AUTO switch is fully pressed, the driver side window will move completely down. This feature can be canceled by pressing the driver side power window button again. DOOR LOCK U L AUTO WINDOW LOCK Press rocker switch to open the passenger window.
Controls and features Press rocker switch to open the rear passenger window(s). Press rocker switch to close the rear passenger window(s). Your vehicle has a power window lock feature. When the power window lock feature is enabled, the passenger and the rear seat power windows cannot be operated by passengers. DOOR LOCK U L AUTO WINDOW LOCK Press rocker switch to enable power window lock.
Controls and features Passenger side control Press rocker switch to open window. Press rocker switch to close window. DOOR LOCK L U WINDOW Rear seat passengers Press rocker switch to open right rear window. Press rocker switch to close right rear window. Press rocker switch to open left rear window. Press rocker switch to close left rear window.
Controls and features Power locks Driver side Press U once to unlock all doors and liftgate. Press L once to lock all doors and liftgate. DOOR LOCK U L AUTO WINDOW LOCK Passenger side Press U once to unlock all doors and liftgate. Press L once to lock all doors and liftgate.
Controls and features Rear liftgate Press rocker switch (key graphic) once to unlock all doors and liftgate. Press opposite side to lock all doors and liftgate. DOOR LOCK Childproof locks for rear doors When you set these locks, the rear doors cannot be opened from the inside. The rear doors can still be opened from the outside when the lock knobs are raised.
Controls and features Move lever to LOCK position (up) to set the lock. Move lever to UNLOCK position (down) to disengage the lock. Two-step unlock feature (if equipped) This feature allows you to unlock all vehicle doors with the key. 1. Unlock driver door. 2. Repeat unlock procedure within 4 seconds.
Controls and features liftgate will unlock when the key is returned to the vertical position (position of key before removal). This feature can be activated by all outside locks on vehicles equipped with keyless entry. Illuminated entry Interior lamps illuminate when either outside front door handle is lifted, unlocked with the keyless entry keypad or the UNLOCK button is pressed on the remote entry transmitter (see Remote entry system or Keyless entry system for further information).
Controls and features Power mirrors 1. Select driver or passenger mirror by moving selector lever left for driver or right for passenger. 2. Move the mirror control knob until mirror reaches desired position. 3. Return the selector lever to the center ‘‘off’’ position.
Controls and features Auxiliary power point This power point is an additional power source for electrical accessories. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. Replacing the tissue box 1. Lift armrest and slide coinholder/tissue box out of console in an upward motion. 2. Replace tissue box. 3. Slide coinholder/tissue tray into console locating pins at bottom of tray. Fit in slots in console bracket.
Controls and features Rear console (if equipped) Your vehicle is equipped with a rear console that includes the following features: 1. Air vents 2. Audio system controls (refer to Audio Guide) 3. Rear seat climate control direction and fan controls 4.
Controls and features Rear climate controls – VOLUME + SEEK BAND MEMORY Turn the air distribution dial to the desired airflow position. – VOLUME + SEEK BAND MEMORY Turn the fan speed dial to the desired position.
Controls and features Controlling airflow Select for air to flow through these vents: – VOLUME + SEEK BAND MEMORY for air to flow through Select these vents: – VOLUME SEEK Cargo area controls Cargo cover (if equipped) Your vehicle is equipped with a cargo shade that covers the luggage compartment of your vehicle.
Controls and features Installing shade 1. Position shade in mounting brackets as shown (tongue faces rear of vehicle). 2. Pull end of shade towards you and hook sides into notches in rear trim panels. To avoid possible injury during a sudden stop or collision, the cover should be attached to the brackets when not in use. Rewinding shade to regain lost tension Over time, the cargo shade may lose its spring tension. If this happens, then follow these instructions to rewind the shade.
Controls and features 3. Fold vinyl edges towards center, making sure that the edges clear the end cap slots. Use tape or rubber band to hold the vinyl on the left side of the roller tube. 4. While holding the vinyl and roller tube, push in the right end cap (marked RH) about 6.4 mm (1/4 inch) to disengage the clutch. Hold end cap in while turning roller tube towards you 14 times. 5. Let go of the right end cap. The clutch should now engage and stop the shade from losing its spring tension. 6.
Controls and features Keyless entry system (if equipped) With the keyless entry keypad, you can: • lock or unlock the vehicle doors and liftgate without using the key. • arm and disarm the anti-theft system. 1•2 3•4 5•6 7•8 9•0 See also Remote entry system and Anti-theft system later in this chapter for more information. Your vehicle has a factory-set 5-digit code that operates the keyless entry system. You can also program your own 5-digit personal entry code.
Controls and features presents them in a sequential order. Press the middle of the buttons (there is only one switch under each button). You can use either code to unlock your vehicle. If a second personal code is entered, the module will erase the old code in favor of the new code. If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter factory-set code. 2. Press 1/2 within five seconds of Step 1. 3. Wait six seconds.
Controls and features locking the doors and liftgate. To lock the doors: • press 7/8 and 9/0 buttons at the same time. This will arm your anti-theft system; see Arming anti-theft system with keyless entry and Anti-theft system later in this chapter for more details. Arming anti-theft system with keyless entry To arm the anti-theft system: • press 7/8 and 9/0 buttons at the same time. To disarm the anti-theft system: • enter either the factory-set code or your personal code.
Controls and features Relock The autolock feature will repeat when: • any door is opened and closed. • the brake pedal is released. Deactivating autolock Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is off, and all vehicle doors and liftgate window are closed. 1. Enter five-digit entry code. 2. Press and hold 7/8 button. 3. Press and release 3/4 button while holding 7/8 button. 4. Release 7/8 button.
Controls and features Additional transmitters can be ordered from your dealer. Unlocking the doors with the remote entry system Press UNLOCK button to unlock driver door. The interior lamps will illuminate. Press UNLOCK a second time within 5 seconds to unlock all doors and liftgate. Locking the doors with the remote entry system Press the LOCK button to lock all doors and liftgate. Press the LOCK button a second time within 5 seconds to confirm that all doors and liftgate are locked.
Controls and features Press the PANIC button to activate the alarm. To turn off the alarm, press the PANIC button again or turn the ignition key to the ON or ACC position. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
Controls and features When installing new batteries, be sure to place the positive (+) side down as marked. Snap the two halves back together. Replacing lost transmitters If a transmitter is lost, take your vehicle’s transmitter to the dealer to have the remote entry system deprogrammed for the lost transmitter. This will prevent unauthorized use of the lost transmitter. You can purchase additional transmitters (up to four can be used) from your dealer.
Controls and features Anti-theft system (if equipped) When set, the anti-theft system protects against unauthorized entry into a locked vehicle. The ignition switch must be in the OFF position to arm the anti-theft system. Arming the anti-theft system Use one of the following methods to arm the system: • Press the LOCK button on the remote entry transmitter (with doors open or closed). OR • Open any door and press the power lock button.
Controls and features • flash the headlamps, park lamps and the THEFT indicator in the instrument cluster. • sound the horn. • disable vehicle starting. The flashing exterior lamps and honking horn will shut off automatically after about 3 minutes. The lights and horn will remain off unless another unauthorized entry is attempted. However, the vehicle will not start until the system is properly disarmed.
Controls and features Delayed accessory Delayed accessory provides power to operate the power windows and power moon roof (if equipped) for 10 minutes after the ignition switch is turned to OFF. If either front door is opened during the 10 minute period the delayed accessory feature is disabled. Battery saver Battery saver is a feature that automatically shuts off power to these lights after 40 minutes: glove box, engine compartment, overhead console, mirror, courtesy and interior lamps.
Seating and safety restraints FRONT BUCKET SEATS Adjusting manual seats Lift to move the seat forward or backward. Pull up to recline the seat.
Seating and safety restraints Adjusting power seats (if equipped) Pull up to recline the seat. Press to tilt front and rear of seat up or down.
Seating and safety restraints Press in the desired direction to raise or lower the seat, or to move the seat backward or forward. Push to increase (+) or decrease (-) lumbar support.
Seating and safety restraints Rear seat four-way head restraints (if equipped) Push the lock release button to raise or lower the head restraint. Push or pull head restraint to desired position. Folding rear seat If your vehicle is equipped with a built-in child seat, the seatback cannot be folded down unless the built-in child seat is fully stowed. 1. Push the lower release handle downward to unlatch seat back. 2. Rotate seatback downward into the load floor position. 3.
Seating and safety restraints Return to upright 1. Push downward on upper outboard corner of seatback and hold. 2. Lift release handle upward to unlatch seat. 3. Rotate seatback upward until seatback latches in the upright position. You will hear a ‘‘click’’ when seatback locks. SAFETY RESTRAINTS PRECAUTIONS The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires the use of safety belts.
Seating and safety restraints To prevent the risk of injury make sure children sit where they can be properly restrained. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
Seating and safety restraints The outboard safety restraints in the vehicle are combination lap and shoulder safety belts. The front and rear seat passenger outboard safety belts have the two types of locking modes described below: Vehicle sensitive (Emergency) locking mode The vehicle sensitive mode is the normal retractor mode, allowing free shoulder belt length adjustment to your movement and locking in response to vehicle movement.
Seating and safety restraints Automatic locking mode In this mode, the shoulder belt is automatically pre-locked; however, the belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder belt fit is desired. • Any time a child safety seat is installed in the vehicle. Refer to Children and infant or child safety seats later in this section.
Seating and safety restraints 2. Grasp the shoulder belt portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates that the safety belt is now in the automatic locking mode. How to cancel the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to completely retract to cancel the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.
Seating and safety restraints 1. To lower shoulder belt height, push the button and slide down. 2. To raise the height of the shoulder belt, push the button and slide up. 3. Pull down on the height adjustment assembly to make sure it is locked in place. Center rear lap belt The center rear seating position has a lap belt with retractor. To unfasten the safety belt: 1. Push the release button on the buckle. This allows the tongue to unlatch from the buckle. 2.
Seating and safety restraints SAFETY BELT WARNING AND INDICATOR CHIME The warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The safety belt is not buckled before the ignition key is turned to ON... The safety belt indicator light illuminates for one to two minutes and the warning chime sounds for 4-8 seconds.
Seating and safety restraints Energy absorbing sew pattern The short plastic boot on the front passenger safety belt covers an energy absorbing sew pattern on the safety belt. In the event of an accident, the sew pattern may release, and the orange REPLACE BELT label may become visible. If any part of the orange label is exposed, the belt must be replaced.
Seating and safety restraints Safety belt extension assembly For some people, the safety belt may be too short even when it is fully extended. You can add about 20 cm (8 in) to the belt length with a safety belt extension assembly (part # 611C22). Safety belt extensions are available at no cost from your dealer. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label.
Seating and safety restraints passenger in the event of a collision. All occupants of the vehicle, including the driver, should always wear their safety belts, even when an air bag supplemental restraint system is provided. Do not place objects or mount equipment on or near the air bag cover on the steering wheel or in front seat areas that may come into contact with a deploying air bag. Failure to follow this instruction may increase the risk of personal injury in the event of a collision.
Seating and safety restraints AIR BAG DESCRIPTION The air bag system activates in collisions more severe than hitting a parked vehicle of similar size and weight head-on at about 45km/h (28 mph).
Seating and safety restraints bags, and the air bags deflate. You may notice smoke and smell the escaping gas after the air bags deflate. This is normal. You and your passenger must wear your safety belts in order for the air bag system to operate effectively. AIR BAG WARNING LIGHT AND CHIME When you turn the ignition key to warning the ON position, the light in the instrument cluster illuminates for approximately six seconds to indicate the air bag system is functional.
Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. If possible, place children in the rear seat of your vehicle. Accident statistics suggest children are safer when properly restrained in rear seating positions than in the front seating positions.
Seating and safety restraints OR • If the child is the proper size, restrain the child in a safety seat. CHILDREN AND INFANT OR CHILD SAFETY SEATS 76 ES PR When installing a child safety seat: • Use the correct safety belt buckle for that seating position. • Make sure the tongue is securely fastened in the buckle. • Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling.
Seating and safety restraints Installing child safety seats in combination lap and shoulder belt seating positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. If you choose to install a child safety seat in the front passenger seat, move the seat as far back as possible. Rear-facing child seats or infant carriers should never be placed in the front seat. 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together.
Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle for that seating position until you hear and feel the latch engage. Make sure the tongue is latched securely by pulling on it. S ES PR 5.
Seating and safety restraints 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing a child in the seat, forcibly tilt the seat forward and back to make sure the seat is securely held in place. 10.
Seating and safety restraints strap. Contact the manufacturer of your safety seat for information about ordering a tether strap if one is not provided to you. Contact your Ford dealer for a free tether anchor kit (613D74) so you can attach a tether anchor bracket to the tether anchor attachment locations in the rear floor. Carefully follow the instructions provided with the kit. Only use the tether attachment hole locations shown.
Seating and safety restraints instruction under Installing child safety seats in combination lap and shoulder belt seating positions in this chapter. 4. Hook the tether strap around the webbing near the center of the shoulder portion of the rear safety belt and tighten. BUILT-IN CHILD SEAT (IF EQUIPPED) The rear seat may include a built-in child seat. This child seat conforms to all federal and Canadian motor vehicle safety standards.
Seating and safety restraints Placing your child in the built-in child seat Failure to follow all of the instructions on the use of this child restraint system can result in your child striking the vehicle’s interior during a sudden stop or crash. Never use the built-in child seat as a booster cushion with the adult safety belts. A child using the adult belts could slide forward and out from under the safety belts. The rear seatback must be fully locked before operating the child restraint system. 1.
Seating and safety restraints 2. Pull both Velcrot straps to release child seat cushion. 3. Lower child seat cushion.
Seating and safety restraints 4. Unfold cushion protector flap onto adult seat cushion. 5. If connected, disconnect the chest clip and buckles. 6. Place the child in the seat and position the left shoulder belt over the child’s left shoulder first, then place the right shoulder belt over the child’s right shoulder.
Seating and safety restraints 7. Insert the left and right safety belt tongues into the left and right slots of the crotch buckle. Verify that the indicator window on each tongue is green to ensure proper safety belt connections. If both tongues do not latch in the buckle, do not use the child seat. See your dealer for repairs. 8. Fasten the left and right chest clip halves together, and adjust the clip (up or down) to comfortably hold the shoulder belts in place on the child’s chest.
Seating and safety restraints 9. Pull on the safety belt tongues to ensure they are both securely latched. If they are not latched, repeat Steps 7 and 8. If necessary, the shoulder belts can be put in automatic locking mode (ALR) to limit the child’s movement in the child seat. The ALR mode may be used if the child is sleeping or attempting to get out of the child seat.
Seating and safety restraints 2. Allow the shoulder belts to fully retract. Removing your child from the built-in child seat 1. Disconnect the chest clip by squeezing the release tabs together and pulling the two sides apart. 2. Press the release button on the crotch buckle. 3. Slide the shoulder belts off the child’s shoulders and remove child. If ALR is engaged, hold either left or right shoulder belt fully out while helping the child slide his arms out of the belts. 4.
Seating and safety restraints 7. Press firmly on the top center of the built-in child seat head restraint to ensure it is stowed properly. Inspecting the built-in child seat after a collision All built-in child restraints, including seats, buckles, retractors, seat latches, interlocks, and attaching hardware should be inspected by a qualified dealer technician after any collision. If the child seat was in use during a collision, Ford recommends replacing it.
Starting your vehicle IMPORTANT SAFETY PRECAUTIONS Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or other enclosed area.
Starting your vehicle 2. Make sure the headlamps and vehicle accessories are off. OFF 3. Make sure the parking brake is set and the gearshift lever is in P (Park). 4 3 H 2 C 5 6 60 UNLEADED FUEL ONLY F 0 0 0 0 0 0 0 H 160 L 180 0 RPM x 1000 P E 80 100 120 o o o o 140 40 20 1 MPH km/h 200 H R N D 2 1 - + L RSM ON SET ACC OFF COAST SRS 4. Turn the key to the ON position (without turning the key to START).
Starting your vehicle CHECK GAGE 4 3 H 2 C - 5 F ABS BRAKE ! P E RPM x 1000 P 80 40 10 0 100 120 80 140 60 30 20 + 0 o o o o 40 1 DOOR AJAR 50 60 70 6 UNLEADED FUEL ONLY 0 0 0 0 0 0 20 90 160 H L 100 180 SPEED CONT 110 MPH R N D 2 1 km/h H 120 ANTITHEFT CHECK ENGINE - + L O/D OFF The above lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is light does not fastened, the illuminate.
Starting your vehicle seconds. If the engine does not start on the first attempt: 1. Turn the ignition key to LOCK and wait approximately 10 seconds. 2. Try starting the engine again. At temperatures above -12°C (10°F), do not hold the key in the START position longer than five seconds. If the engine does not start on the first attempt: 1. Turn the ignition key to LOCK and wait approximately five seconds. 2. Try starting the engine again.
Starting your vehicle 2. Press the accelerator all the way to the floor and hold. 3. Turn the key to START. Release it once the engine starts. 4. Release the accelerator gradually as the engine speeds up. If the engine still does not start, refer to Fuel pump shutoff switch in the Roadside emergencies chapter. Engine block heater (if equipped) To prevent electrical shock, do not use your engine block heater with ungrounded electrical systems or two-pronged (cheater) adapters.
Starting your vehicle GUARDING AGAINST EXHAUST FUMES Carbon monoxide, although colorless and odorless, is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Have the exhaust and body ventilation system checked whenever: • The vehicle is raised for service. • The sound of the exhaust system changes. • The vehicle has been damaged in a collision.
Starting your vehicle Ventilating your vehicle • If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (1 inch). Adjust the heating or air conditioning to bring in fresh air. • Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Driving BRAKES The anti-lock brake system (ABS) Anti-lock brake operation differs slightly from standard brake operation. Apply the brakes steadily. DO NOT pump the brakes in a panic stop. The brake system will prevent wheel lockup by automatically releasing and reapplying the brakes. Even with ABS, the brakes could lock up on roads with alternating slippery and dry patches or with loose surfaces such as snow or gravel. Be careful when braking. The ABS conducts a self-test each time the vehicle is driven.
Driving ABS warning light The ABS light in the instrument cluster illuminates and remains illuminated if an ABS fault is detected. Have your vehicle serviced as soon as possible. Normal braking operation is still effective unless the light is also illuminated. Parking brake The parking brake should be used whenever the vehicle is parked. Push pedal downward to set the parking brake.
Driving Pull release handle towards you to release parking brake. If the parking brake is fully released, but the warning light remains on, have the brakes checked immediately. They may not be working properly. AUTOMATIC TRANSMISSION OPERATION (4R70W) Hold the brake pedal down while you move the gearshift from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone.
Driving Pull gearshift lever towards you and downward to move the automatic gearshift. P P R N D 2 1 R N D 2 1 P - Park Always come to a complete stop before shifting into or out of P (Park). Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). R - Reverse Always come to a complete stop before shifting into or out of R (Reverse). N - Neutral Vehicle is free to roll. Do not leave the vehicle unattended with the transfer case in the N (Neutral) position.
Driving D - Overdrive The normal driving position for the best fuel economy. Transmission operates in gears 1-4. D (Overdrive) can be disengaged by pressing the transmission control switch on the gearshift lever. The transmission control indicator light on instrument cluster will remain off.
Driving on downgrades. Transmission operates in gears 1-2. 1 - Low Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to D (Overdrive). Selecting 1 (Low) at higher speeds causes a shift to 2 (Second), and will shift to 1 (Low) after vehicle decelerates to the proper speed. Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P unless the brake pedal is depressed.
Driving Do not drive your vehicle until you verify that the brakelamps are working. If your vehicle gets stuck in the mud or snow it may be rocked out of the spot. To rock the vehicle out, shift between forward and reverse gears in a steady rhythm. Press lightly on the accelerator in each gear. Do not rock the vehicle for more than a few minutes, because it could damage the vehicle. Do not spin the wheels at over 55 km/h (35 mph). The tires may fail and injure a passenger or bystander.
Driving features to make them capable of performing in a wide variety of off-road applications. Specific design characteristics give them higher centers of gravity than ordinary passenger cars. Utility and four-wheel drive vehicles are NOT designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
Driving should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read Four-Wheeling in your owner’s portfolio. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. Do not reduce the tire pressures but shift to a lower gear and drive steadily through the terrain. Apply the accelerator slowly and avoid spinning the wheels.
Driving that could damage drive components. If the transmission and transfer case are submerged in water, their fluids should be checked and changed, if necessary. All rear axle lubricants must be replaced every 160,000 km (100,000 miles) or if the axle has been submerged in water. Otherwise, check the lubrication of the rear axle according to the intervals in the Service Guide. Driving on hill or slope terrain When driving on a hill, avoid driving crosswise or turning on steep slopes.
Driving heavy load. If vehicle speed drops more than 15 - 25 km/h (8 - 14 mph) the speed control will cancel automatically. Resume speed with accelerator pedal. If speed control cancels after climbing the hill, reset speed by pressing and holding the SET ACCEL button or returning to previous speed by pressing the RESUME button (to resume speeds over 50 km/h [30 mph]). Automatic transmissions may shift frequently while driving up on steep grades.
Driving between forward and reverse gears. DO NOT rock the vehicle for more than a few minutes. The transmission and tires may be damaged or the engine can overheat. Do not spin the wheels at over 55 km/h (35 mph). The tires may fail and injure a passenger or bystander. VEHICLE LOADING It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Driving • Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals gross vehicle weight rating (GVWR) minus base curb weight. • GVW (Gross Vehicle Weight): Base curb weight plus the payload weight (including passengers, cargo, and optional equipment). Remember, the GVW is not a limit or a specification. • GVWR (Gross Vehicle Weight Rating): Maximum total weight of the base vehicle, passengers, optional equipment and cargo.
Driving • Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating equals the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow.
Driving Do not use replacement tires with lower weight capacities than the original because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher weight limit than the originals do not increase the GVWR and GAWR limitations. TRAILER TOWING Your vehicle may tow a Class I or II trailer provided the maximum trailer weight is less than or equal to the maximum trailer weight listed for your engine and rear axle ratio. See the Trailer towing table later in this chapter.
Driving If the GVWR or the GAWR specified on the Safety Compliance Certification Label is exceeded, your vehicle may be damaged or you may lose control and injure someone. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limits of the vehicle and could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Calculating the load your vehicle can carry/tow 1.
Driving below the maximum shown under maximum trailer weight on the chart. Trailer Towing Table 4R70W Automatic Transmission Engine Rear Axle Ratio Maximum GCWR kg (lb)1 Maximum Trailer Weight kg (lb)2 Maximum Frontal Area of Trailer ft 2-Wheel Drive 5.0L 3.73 4,990 (11,000) 3,039 (6,700) 50 All-Wheel Drive 5.0L 3.73 4,990 (11,000) 2,944 (6,500) 50 1 For high altitude operation, reduce GCWR by 2% per 300 meters (1,000 ft) elevation.
Driving bumper has a Class II rating (1590 kg/3500 lb trailer weight and 159 kg/350 lb tongue weight). Safety chains Always connect the trailer’s safety chains to the vehicle. To connect chains when towing with the step bumper, cross the chains under the trailer tongue and allow slack for turning corners. Connect the chains to the holes in the underside of the hitch plate for a Class II frame mounted hitch.
Driving Trailer lamps Trailer lamps are required on most towed vehicles. Make sure your trailer lamps conform to Federal and local regulations. See your dealer or trailer rental agency for the proper instructions and equipment for hooking up trailer lamps. Do not hook the trailer lamps directly into the vehicle’s lighting system wiring. If the trailer lamps are not installed properly, the warning lights in the instrument cluster may not work properly.
Driving Servicing while towing If you tow a trailer for long distances, your vehicle will require more frequent service intervals. Refer to the Service Guide for more information. Trailer towing • Practice turning, stopping and backing in an area before starting on a trip to get the feel of the vehicle/trailer combination. When turning, drive slightly beyond the normal turning point so the trailer wheels will clear curbs and other obstacles. • Allow more room for stopping with a trailer attached.
Driving Luggage rack (if equipped) Load luggage as far back as it will safely go without loading more than 45 kg (100 lb) or cause the vehicle to exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR). Use the following steps to adjust the luggage rack. • Turn adjustment wheel backward to unlock crossbar and slide crossbar forward or backward. • Turn adjustment wheel forward to lock crossbar.
Driving • sudden stops • extended engine idling • use of speed control in hilly terrain • extended use of the air conditioner, defroster, rear window defroster and other accessories • underinflated tires • heavy loads • aftermarket add-ons such as bike, ski or luggage racks, bug deflectors, etc.
Roadside emergencies HAZARD SWITCH Use the hazard flashers to warn traffic of vehicle problems. Press button down to activate hazard flashers. Press button again to deactivate hazard flashers.
Roadside emergencies Press the red button to reset the fuel pump. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Roadside emergencies Standard fuse amperage rating and color Fuse Rating Color 7.5 amp Brown 10 amp Red 15 amp Blue 20 amp Yellow 30 amp Light Green 30 amp fuse link Pink 40 amp Green 60 amp fuse link Yellow 80 amp fuse link Black 100 amp fuse link Blue Even after a fuse is replaced, it will continue to blow if the cause of the overload is not identified and corrected. If a fuse continues to blow, have the vehicle’s electrical system checked.
Roadside emergencies Use the fuse puller tool provided on the passenger compartment fuse panel cover to replace fuses. 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 33 2 36 1 Number Fuse Amperage Rating Circuits Protected 1 7.5 amp Power mirror, power antenna 2 7.5 amp High-mount brakelamp 3 15 amp Parking lamps 4 10 amp Left headlamp 5 10 amp Data link connector 6 7.
Roadside emergencies Number Fuse Amperage Rating Circuits Protected 7 7.5 amp Illumination switches 8 10 amp Right headlamp, fog lamp system 9 10 amp Autolamps 10 7.5 amp Rear blower, speed control, GEM system, brake interlock, overhead console 11 7.5 amp Warning lamps 12 10 amp Liftgate wiper/washer, front washer 13 15 amp Brake on/off switch 14 10 amp Anti-lock system 15 7.
Roadside emergencies Number Fuse Amperage Rating Circuits Protected 26 10 amp 4R70W overdrive, DRL system, backup lamps, rear defroster relay 27 10 amp Underhood lamp, map lights, glove box lamp, overhead lamp, visor lamps, accessory delay, dimmer switch illumination 28 7.5 amp GEM system 29 10 amp Audio system 30 - Not used 31 7.5 amp Rear blower motor relay 32 7.5 amp Heated rear window 33 15 amp DRL module, RH and LH headlamp, instrument cluster 34 7.
Roadside emergencies Power distribution box Lift cover towards front of vehicle to access the power distribution box. The high-current fuses in the power distribution box protect your vehicle’s main electrical systems from overloads.
Roadside emergencies High Current Fuse Rating Color 20 amp Yellow 30 amp Light green 40 amp Orange 50 amp Red 60 amp Blue Always disconnect the battery before servicing high current fuses. Always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs.
Roadside emergencies Maxi fuses Fuse Amps Circuits protected 8 30 amp Battery saver relay, headlamp relay 9 50 amp Blower motor relay, blower motor 10 30 amp Power seats, power lumbar, door lock/unlock relays, accessory delay relay 11 20 amp Horn relay, Powertrain control module (PCM) 12 - Not used 13 60 amp Hazard flasher, brake ON/OFF switch, cigar lighter, power antenna, power mirrors, autolamps, instrument cluster, GEM, radio, blower motor relay 14 60 amp Ignition switch Mini fus
Roadside emergencies Mini fuses Fuse Amps Circuits protected 6 15 amp Generator/voltage regulator 7 20 amp Not used 8 15 amp Foglamp relay, daytime running lamp module 9 - Not used 10 - Not used 11 20 amp HEGO system Relays Relays are located in the power distribution box. Relays receive signals from components or systems and transfer these signals to activate or deactivate other components or systems. Mercury recommends that relays be replaced by a qualified technician.
Roadside emergencies Relay number Circuits connected 1 Wiper run relay 2 Horn relay 3 Wiper HI/LO relay 4 WOT A/C relay 5 PCM power relay 6 Fuel pump relay Diode number Circuits connected 1 ABS diode 2 PCM diode CHANGING TIRES Tire change procedure 1. Park on a level surface. 2. Activate the hazard flashers. 3. Set the parking brake. 4. Place the gearshift in P (Park). 5. Block the diagonally opposite wheel. 6. Remove the jack and lug wrench.
Roadside emergencies 7. Remove the jack handle (located underneath rear seat). 8. Assemble the jack handle to the lug wrench. 9. Insert drive section of the jack handle into the actuator hole and turn counterclockwise until the cable is slack enough to allow spare tire to be pulled rearward from under the vehicle. 10. Slide spare tire rearward and remove retainer.
Roadside emergencies 11. Insert tapered end of the lug nut wrench behind hubcaps and twist off. Not using the tapered end of the lug nut wrench at the pry-off notches may result in damage to the finish of the wheel and ornament. 12. Loosen the wheel lug nuts with the lug wrench about one half turn. 13. Position the jack on the lower suspension arm to raise front wheel.
Roadside emergencies Position the jack under the rear axle to raise the rear wheel. 14. Turn the jack handle clockwise and raise the vehicle until the tire just clears the ground. 15. Remove the wheel lug nuts and flat tire, and install the spare. 16. Install the lug nuts and tighten until snug. Use of wheel or lug nuts other than original equipment could cause damage to the wheel or mounting system and allow the wheels to come off while the vehicle is in motion. 17.
Roadside emergencies To stow largest flat tire, place inside vehicle and secure with webbing retainer. JUMP STARTING A DISABLED VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. To protect yourself when charging a battery, always shield your face and eyes. Make sure that you can breath fresh air. Batteries contain sulfuric acid which burns skin, eyes and clothing.
Roadside emergencies vegetable oil. Call a doctor immediately. To avoid damage or injury, follow these directions in the order they are given. If in doubt, call for road service. 2 + 4 – Before jump starting a vehicle: • Make sure the booster battery vehicle has a 12-volt starting system (a 24-volt power supply will cause vehicle damage). • Park the vehicles close to each other, but do not allow the vehicles to touch each other. • Check to make sure neither battery is disconnected.
Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Start the engine in the vehicle with the booster battery. 6. Wait a few minutes and start the engine in the vehicle with the disabled battery. 7. After a few minutes, the disabled battery should be recharged. Disconnect the jumper cables in reverse order.
Roadside emergencies WRECKER TOWING It is recommended that your vehicle be towed with wheel lift and dollies or flatbed equipment. Do not tow with slingbelt equipment. Ford Motor Company has not developed or approved a T-hook or slingbelt towing procedure.
Maintenance and care SERVICE RECOMMENDATIONS Whenever possible, Ford has designed parts that do not require servicing. However, when servicing is required, Ford’s goal is to make servicing your vehicle as easy as possible. To help you: • We highlight do-it-yourself items in the engine compartment for easy location. • Often, parts (such as the headlamp bulbs) may be replaced without tools. • We provide you with a Service Guide that makes tracking routine service of your vehicle easy.
Maintenance and care come on unexpectedly; always turn the engine off and let it cool. The cooling fan is automatic and may come on at any time. Always disconnect the negative terminal of the battery before working near the fan. • Never get under a vehicle supported only by a jack. If you must work under a vehicle, use safety stands. • Keep all lit cigarettes and other smoking materials away from the battery and all fuel-related parts. Working with the engine off 1.
Maintenance and care Working with the engine on 1. Set the parking brake and make sure that the gearshift is securely latched in P (Park). 2. Do not work on a vehicle in an enclosed space with the engine running. 3. Block the wheels to prevent the vehicle from moving unexpectedly. 4. If work must be done with the engine running, avoid wearing loose clothing or jewelry that could get caught in moving parts. Take appropriate precautions with long hair.
Maintenance and care 6 3 5 4 2 1 5.
Maintenance and care CHECKING AND ADDING ENGINE OIL Use WSS-M2C153-F motor oil CERTIFIED FOR GASOLINE ENGINES by the American Petroleum Institute. Engine oils with an SAE 5W–30 viscosity and displaying the American Petroleum Institute certification mark are preferred for your vehicle. They provide the best engine performance, fuel economy and engine protection for all climates down to –25°C (–15°F).
Maintenance and care Checking the engine oil Check the engine oil every time you fuel your vehicle. Check the engine oil level more frequently if the vehicle is carrying a heavy load, towing a trailer, idling for extended periods (like police, taxi, or shuttle service vehicles), or driven at high speeds for extended periods of time. To check engine oil: 1. Once the engine is warm, turn the engine off. Make sure the vehicle is parked on level ground. 2. Depress the parking brake.
Maintenance and care Adding engine oil If the fluid level is below the MIN line, add engine oil. Add engine oil through the oil filler cap and use a funnel to pour oil into the opening. Make sure you use a certified engine oil of the preferred viscosity. Recheck the oil level. Make sure that the oil level is not above the MAX line on the dipstick. Continuous contact with USED motor oil has caused cancer in laboratory rats.
Maintenance and care 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3. If necessary, add brake fluid until the level reaches within 1/89 of the MAX line on the reservoir. • Do not exceed MAX. MAX Use only a DOT 3 brake fluid certified to meet Ford specification ESA-M6C25-A. Refer to Lubricant specifications. Brake fluid is toxic. If you use brake fluid that is not DOT 3, you will cause permanent damage.
Maintenance and care CHECKING AND ADDING WASHER FLUID Visually inspect the fluid level in the washer fluid reservoir. If washer fluid needs to be added to the reservoir: 1. Lift the washer fluid reservoir cover. 2. Add enough washer fluid to fill the reservoir.
Maintenance and care Checking and adding washer fluid for the liftgate The opening for this reservoir is located on the left side of the vehicle above the tail lamp. Be sure to close the cover after filling and before closing the liftgate. The reservoir must be filled slowly to allow trapped air to escape. Use of a funnel is recommended for easier filling. CHECKING AND ADDING ENGINE COOLANT Check the engine coolant level in the reservoir at least once a month.
Maintenance and care or 80,000 km (50,000 miles). It is not necessary and not recommended to use supplemental coolant additives in your gasoline-powered vehicle. These additives may harm your engine cooling system. When you change or add engine coolant, it is important to maintain your engine coolant concentration between 40% (-24°C [11°F]) and 60% (-52°C [-62°F]), depending on your local climate conditions. A coolant concentration below 40% may cause the engine to overheat on a warm day.
Maintenance and care 1. Before you remove the coolant recovery cap, turn the engine off and let it cool. Even when the engine is cool, be careful when removing the recovery cap. Wrap a thick cloth around the cap for safe removal. 2. When the engine is cool, lift the cap. 3. Step back while pressure releases. 4. When you are sure that all the pressure has been released, remove the recovery cap. 5. Stand away from the reservoir opening; hot steam may blow out or hot engine coolant may even splash out. 6.
Maintenance and care Checking the cooling system hoses Before adding or replacing coolant, inspect all cooling system hoses for: • deterioration • leaks • loose clamps CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year by completing the following steps: 1. Start the engine. 2. When the engine coolant temperature gauge reaches the normal zone, turn off the engine.
Maintenance and care ING NOT DO ERFILL OV POW STE ER U ER FL ID 3. Visually inspect the fluid level in the power steering reservoir. 4. If necessary, add power steering fluid until the fluid level reaches MAX. Do not overfill the power steering reservoir. • As a maintenance precaution, visually inspect the lines and hoses of the power steering system for leaks and damage. • If new fluid is frequently required, consult a qualified service technician.
Maintenance and care Your vehicle does not use up transmission fluid. However, it is recommended that you check the transmission fluid at least twice a year. The fluid level should be checked if the transmission is not working properly, i.e., the transmission slips or shifts slowly or if you notice some sign of fluid leakage. It is preferable to check the transmission fluid level at normal operating temperature, after approximately 32 km (20 miles) of driving.
Maintenance and care 6. Remove the dipstick and inspect the fluid level. The fluid level should be within the crosshatched area, or if the vehicle has not been driven, between the holes near the bottom of the indicator. DON'T ADD IF IN CROSSHATCHED AREA • CHECK WHEN HOT IDLING IN PARK 7. If necessary, add fluid in .25 L (1/2 pint) increments through the filler tube until the level is at the correct area on the dipstick. If an overfill occurs, excess fluid should be removed by a qualified technician.
Maintenance and care Checking and adding transfer case fluid 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at the bottom of the opening. When adding transfer case fluid: • Use fluid certified to meet Ford Motor Company lubricant specifications. Refer to Refill capacities and Lubricant specifications later in this chapter.
Maintenance and care • Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. BATTERY If the original equipment maintenance-free battery needs replacing, it may be replaced with a low-maintenance battery. For information on replacement batteries, refer to Motorcraft part numbers in the Capacities and specifications chapter. + – Batteries normally produce explosive gases that can cause personal injury.
Maintenance and care the electrolyte level and adding water. Check the electrolyte level every 24 months or 40,000 km (24,000 miles) in average temperatures 32°C (90°F). Keep the electrolyte level in each cell up to the level indicator. Do not overfill. If the level gets low, refill the battery with distilled water. If necessary, distilled water may be substituted with tap water that is not hard and does not have a high mineral or alkali content.
Maintenance and care 3. Let the engine idle for at least one minute. 4. The relearning process will automatically complete as you drive the vehicle. • If you do not allow the engine to relearn its idle, the idle quality of your vehicle may be adversely affected until the idle is eventually relearned. • If the battery has been disconnected or a new battery has been installed, the clock and preset radio stations must be reset once the battery is reconnected.
Maintenance and care Changing your air filter 1. Loosen the clamp that secures the air cleaner in place. Separate the two halves of the air cleaner. 2. Remove the air filter element from the open end of the engine air cleaner and replace it with a new element. 3. Replace the two halves of the air cleaner and secure the clamp. CHECKING AND CHANGING WIPER BLADES Check the windshield wiper blades at least twice a year or whenever the wipers seem less effective than usual.
Maintenance and care To make reaching the wiper blades easy, simply turn the ignition to the ON position and turn the wipers on. Wait for them to reach a vertical position and turn the ignition to LOCK. Do not move the wipers manually across the windshield as this may cause damage to the wipers. Inspect the wiper arm pivots on a regular basis to ensure that the wiper arms move freely. Lubricate the pivot points as necessary.
Maintenance and care on wiper blade until lock tab is engaged. To replace liftgate wiper blade: 1. Pull wiper arm away from liftgate window. 2. Use small screwdriver to depress lock tab and pull wiper blade upwards and away from wiper arm. 3. Attach new wiper blade by pushing wiper arm post through hole in wiper blade until lock tab is engaged. Information about tire grades New vehicles are fitted with tires that have their Tire Quality Grade (described below) molded into the tire’s sidewall.
Maintenance and care grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear 11⁄2 times as well on the government course as a tire graded 100.
Maintenance and care Temperature A B C The temperature grades, from highest to lowest, are A, B and C. These grades represent the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden failure.
Maintenance and care when tires are cold (after the vehicle has been parked for at least one hour or driven less than 5 km (3 miles). The cold pressure amount is listed on the Safety Compliance Certification Label located on the inside driver’s door latch pillar. Improperly inflated tires can affect vehicle handling and can fail suddenly, possibly resulting in loss of vehicle control. Rotating your tires Rotate your tires at regular intervals to ensure even wear.
Maintenance and care Four tire rotation Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias belted or bias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure all replacement tires are of the same size, type, load-carrying capacity, and tread design, e.g., “All Terrain”, as originally offered by Ford.
Maintenance and care Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. IDENTIFYING TIRE TYPES Refer to the Safety Compliance Certification Label to determine the specific size tire and wheel Ford Motor Company recommends for use on this vehicle. All wheel/tire combinations (including spare) must be the same size for AWD equipped vehicles.
Maintenance and care • Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re-tighten the chains. If this does not work, remove the chains to prevent damage to your vehicle. • If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.
Maintenance and care If you replace your fuel cap with an aftermarket fuel filler cap, the customer warranty may be void if any damage to the fuel tank and/or fuel system occurs. If the fuel cap is venting vapor or you hear a hissing sound, wait until it stops before completely removing the cap. Automotive fuels can cause serious injury or death if misused or mishandled. Extinguish all smoking materials and any open flames before fueling your vehicle. Automotive fuels can be harmful or fatal if swallowed.
Maintenance and care of disulfiram for the treatment of alcoholism. Breathing gasoline vapors or skin contact could possibly cause an adverse reaction. Consult a physician immediately. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines, that contain oxygenates such as a maximum of 10% ethanol or 15% MTBE. There should be no more than 5% methanol with cosolvents.
Maintenance and care issued a gasoline specificaton to provide information on high quality fuels that optimize the performance of your vehicle. We recommend the use of gasolines that meet the AAMA specification if they are available. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use a high-quality fuel. Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle.
Maintenance and care Calculating fuel economy 1. Fill the tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the final odometer reading. Keep a record for at least one month. This will provide an accurate estimate of the vehicle’s fuel economy. 4.
Maintenance and care your vehicle to comply with applicable exhaust emission requirements. For more information on your vehicle’s emission control system, see the Vehicle Emission Control Information decal located on the left side of the engine compartment. Follow these guidelines to ensure proper emission system operation: • Use only unleaded fuel. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is in motion.
Maintenance and care If you notice one or more of the following, the emission system may not be working properly. Have the vehicle serviced as soon as possible. • Fluid leaks. CHECK • The and ENGINE lights illuminate in the instrument cluster and remain lit. • Strange odors. • Engine runs more than five seconds after shut-off or engine misfires, surges, stalls or backfires. • Loss of oil pressure. When servicing your vehicle, never use a metal exhaust collector.
Maintenance and care Preparing your vehicle for inspection/maintenance testing In some localities it may become a legal requirement to pass an Inspection/Maintenance test of the On-Board Diagnostic (OBD II) system. If the vehicle’s powertrain system or battery has just been serviced, the OBD II system is reset to a not ready for I/M testing condition.
Maintenance and care EXTERIOR LAMPS Replacing the exterior bulbs It is a good idea to check the operation of the following lights frequently: • Headlamps • High-mount brakelamp • Tail lamps • Brakelamps • Backup lamps • Hazard flasher 172
Maintenance and care • Turn signals • License plate lamp • Fog lamps • Interior overhead lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Headlamps Handle a halogen bulb carefully and keep out of children’s reach.
Maintenance and care 3. Remove electrical connector by grasping wires and pulling rearward. 4. Remove bulb retaining ring by turning it 1/8 turn to free it from the socket. Slide the ring off the plastic base. 5. Carefully remove the bulb assembly from its socket by gently pulling it rearward. 6. With the flat side of the bulb’s plastic base facing upward, insert the glass end of the bulb into the socket.
Maintenance and care remove and replace any of the bulbs. 1. Remove the two (2) screws retaining rear lamp to vehicle. 2. Remove rear lamp by pulling rearward to disengage two lower barbed retainers. 3. 4. 5. 6. 7. Remove socket from lamp. Remove bulb from socket. Install bulb in socket. Install socket to lamp. Replace rear lamp. Hazard flasher For more information on the hazard flasher and hazard switch, refer to Hazard switch in the Roadside emergencies chapter. For bulb replacement, see your dealer.
Maintenance and care Turn signals For more information on the turn signals, refer to Turn signals in the Controls and Features chapter. For bulb replacement, see your dealer. License plate lamp To change the license plate bulb, follow this procedure: 1. Use a screwdriver to detach the lamp from the bumper. 2. Turn and pull the socket from the lamp and remove the bulb. 3. Replace socket into lamp and press lamp back into bumper.
Maintenance and care Fog lamps 1. Disconnect the electrical connector from the back of the foglamp by turning it counterclockwise. 2. Remove bulb by lifting retaining clip and pulling the bulb from the assembly. 3. Replace the bulb and insert the bulb assembly back into the foglamp. 4. Lock bulb assembly into place by turning it clockwise until it stops. Interior overhead lamp The interior overhead lamp is located in the overhead console.
Maintenance and care 1. To remove the lens, pry with a small screwdriver as shown. LAMP MODE LAMP 2. To remove the bulbs, rotate bulb holder counterclockwise 90°. The bulb and bulb holder will drop out. LAMP 3. Pull bulb from bulb holder. Insert new bulb. 4. To replace the bulb holder, push up and rotate clockwise 90°. 5. Replace lens.
Maintenance and care BULB SPECIFICATIONS Number of Bulbs Trade Number Headlamps 2 9007 Front lamp and turn signal 4 3157NA* Front side marker lamp 2 916NA* Underhood lamp 1 906 Fog lamps 2 H3 Rear back-up lamp 2 3156 High-mount brakelamp 1 2 License plate lamp 2 194 Rear tail/brake lamp 2 3157 Turn lamp 2 3156 1 211-2 Description Exterior Illumination Rear Lamps - Exterior Interior Courtesy Lamps Cargo lamp Dome lamp (low series) 1 912 Dome lamp (high series) 1 906
Maintenance and care Description Number of Bulbs Trade Number 1 161 Radio Illumination1 Instrument Panel Ashtray lamp Glove compartment lamp 1 194 1 each 194 A/C controls 1 161 Rear window wiper/washer control 1 2 Headlamp controls 1 1815 Heater controls 1 161 Instrument cluster Instrument Panel Controls 1 Replaceable at Lincoln/Mercury and Ford authorized radio service centers. 2 See your dealer for bulb replacement.
Maintenance and care See your Lincoln/Mercury or Ford dealer for precise adjustment of your headlamps. CLEANING AND CARING FOR YOUR VEHICLE Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent. Always use a clean sponge and plenty of water for best results.
Maintenance and care warranty on paperwork, remove aggressive particles such as bird droppings, tree sap, insect remains, tar spots, road salt, and industrial fallout immediately. Cleaning the wheels Wash the wheels with the same detergent you use to clean the body of your vehicle. Do not use acid based wheel cleaners, steel wool, fuel, or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces. Use a tar and road oil remover to remove grease and tar.
Maintenance and care Cleaning the engine A clean engine is more efficient than a dirty one because a buildup of grease and dirt acts as an insulator and keeps the engine warmer than normal. Follow these guidelines to clean your engine: • Take care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • In order to avoid cracking the engine block, do not spray with cold water.
Maintenance and care Cleaning the built-in child seat Clean the built-in child seat with mild soap and water. Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets.
Capacities and specifications MOTORCRAFT PART NUMBERS Component Motorcraft part number Spark plug 1 AWSF-32EE* Air filter FA-1641 Fuel filter FG-872 Oil filter FL-1A Battery BXT-65-650 or BXT-65-850 (optional) P.C.V. valve EV-152 1 Refer to Vehicle Emission Control Information Decal for spark plug and gap specifications. *If any spark plug needs to be removed for examination, each spark plug removed must be reinstalled in the same cylinder. Cylinders 1-4 have an “EG” suffix.
Capacities and specifications Fluid Component Capacity Transfer case fluid (if equipped) Borg Warner AWD transfer case 1.25 L (2.64 pts.) Transmission fluid, automatic Automatic 4R70W (2WD and AWD) 13.2 L (13.9 qts.) Windshield washer fluid, front Front washer fluid reservoir 2.6 L (2.8 qts.) Windshield washer fluid, rear Liftgate washer fluid reservoir 3.1 L (3.3 qts.) 1 Fill to 6-15 mm (1/49 to 9/169) from the bottom of the filler hole. Includes 1 L (1 qt.) for filter replacement.
Capacities and specifications LUBRICANT SPECIFICATIONS Ford part Component name Ford part number Ford specification Windshield washer reservoir Ultra-Clear Windshield Washer Concentrate C9AZ19550-AA or BA ESR-M17P5-A Body hinges, latches, door striker plates and rotors, seat tracks, door checks and tracks, hood latch, auxiliary latch, and fuel filler door and spring Multi-Purpose Grease D0AZ-19584-AA or D7AZ-19584-AA ESB-M1C93-A or ESB-M1C159-A Steering column, U-joints, clutch linkage pivots, pa
Capacities and specifications Component Ford part name Ford part number Ford specification Engine oil Motorcraft Motor Oil 5W-30 Super Premium X0-5W30 QSP WSS-M2C153-F with API Certification mark Door weatherstrips Silicone Lubricant C0AZ-19553-AA ESR-M13P4-A Automatic transmission shift linkage and brake pedal shaft Premium Long-Life Grease XG-1-C or K ESA-M1C75-B Automatic transmission 4R70W Motorcraft MERCONt ATF XT-2-QDX MERCONt Power steering reservoir Motorcraft MERCONt ATF XT-2-
Capacities and specifications Ford part name Ford part number Ford specification Engine coolant Premium Cooling System Fluid E2FX-19549-AA ESE-M97B44-A Transfer case front output slip shaft Premium Long-Life Grease XG-1-C or K ESA-M1C75-B Transfer case Motorcraft MERCONt ATF XT-2-QDX MERCONt Dana 35 front drive axle 4x4 Gear Oil F1TZ-19580-A WSL-M2C191-A Component 1 Add 118 ml (4oz.
Capacities and specifications VEHICLE DIMENSIONS A B C D E Dimensions A = Overall height 1.83 m (67.3 in.) B = Track front/rear 1.49 m (58.3 in.) C = Overall width (excluding mirrors) 1.87 m (70.2 in.) D = Wheelbase 2.83 m (111.9 in.) E = Overall length 4.78 m (184.3 in.
Capacities and specifications VEHICLE IDENTIFICATION NUMBER (VIN) 191
Reporting safety defects If you believe that your vehicle has a defect which could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Index Air bag supplemental restraint system ............71,74,75,76,77,82,87 and child safety seats .......................74,76,77,82,87 description ................................73 indicator light ...........................74 Air cleaner filter replacing ..................................156 All Wheel Drive .........................102 Anti-theft system ........................56 arming the system ....................56 disarming a triggered system ..57 disarming an untriggered system .................
Index Flat tire ......................................131 Fluid refill capacities ................185 Foglamps ..............................16,177 Fuel calculating fuel economy .......167 choosing the right fuel ...........166 improving fuel economy ........116 safety information relating to automotive fuels .....................164 Fuel gauge .....................................7 Fuel pump shut-off switch ..16,118 Fuse panels ...............................120 power distribution box ...........
Index Parts (see Motorcraft Parts) ...185 Power door locks ........................38 Power steering fluid, checking and adding ....148 Rear climate control system ......45 Refill capacities for fluids ........185 Relays .................................127,128 Remote entry system arming and disarming the anti-theft system .................52,54 locking/unlocking doors ...........53 panic alarm ...............................53 replacement/additional transmitters ...............................
Index Windshield defrosting ..................................21 Windshield washer fluid and wipers checking and replacing wiper blades ......................................156 operation ...................................
Filling station information Fuel info Unleaded only - 87 octane Fuel tank capacity 79.5 L (21.
