Assembly Instructions

ManualsBrandsMercury Row ManualsFurnitureLafever 25'' Tall 1 - Drawer Nightstand

Table Of Contents

P.1

Keep these instructions for future reference.

Summary of content (10 pages)

PAGE 1
Assembly Instructions Keep these instructions for future reference. P.
PAGE 2
P.
PAGE 3
1 12 14 7 6 13 2 11 3 10 15 5 4 9 8 8 9 1 Top panel 01 pcs 9 Left foot 02 pcs 2 Right side panel 01 pcs 10 Front drawer 01 pcs 3 Left side panel 01 pcs 11 Left side drawer 01 pcs 4 Bottom front crossbeam 01 pcs 12 Right side drawer 01 pcs 5 Back crossbeam 01 pcs 13 Drawer bottom 01 pcs 6 Upper front crossbeam 01 pcs 14 Drawer back 01 pcs 7 Back panel 01 pcs 15 Base 01 pcs 8 Right foot 02 pcs P.
PAGE 4
A Ø8*30mm Wooden dowel 26 pcs B Ø3,0*14mm Screw 06 pcs C Ø6,0*10mm Screw 04 pcs D Ø4,0*30mm Screw 27 pcs E M4*22mm Screw 01 pcs F Ø4,5*45mm Screw 12 pcs G Ø10*10 Nail 16 pcs H 300mm Right Slide 01 pcs I 300mm Left Slide 01 pcs J Knob 01 pcs K Glue 01 pcs Hammer recommended for assembly (not included) P.
PAGE 5
Step 1 A A A A 2 A A 3 A 12 A A 11 A 15 A A A A A A A A A A 6 A A A 4 A A Please assemble on a clean soft surface to avoid damage. 5 K 01 Glue tube A A 26 A Ø8*30mm Step 2 Please assemble on a clean soft surface to avoid damage. C C Pre-Drilled holes C C H I 3 2 C C C 04 Ø6,0*10mm I The wheel to the Front H 01 Right slide 300mm I 01 H The wheel to the Front Left slide 300mm P.
PAGE 6
Step 3 3 D D D 15 D K 01 Glue tube D 03 Ø4,0*30mm Step 4 6 D 4 2 D D D D 5 K D D 01 Glue tube D 07 Ø4,0*30mm P.
PAGE 7
Step 5 1 D D D D K 01 Glue tube D 06 Ø4,0*30mm Step 6 D D D D D 03 Ø4,0*30mm P.
PAGE 8
Step 7 9 F F F F 8 8 F F F F 9 Apply glue to leg contact surfaces 1º F 2º K F F F 12 Ø4,5*45mm K 01 Glue tube Step 8 G G G G G G G 7 G G G G G G G G 16 Ø10*10 P.
PAGE 9
Step 9 14 12 D 11 D D D DD D 13 D 10 The wheel to the Back B B B Bottom I E B B H J B E 01 M4x22mm B 04 Ø3,0*14mm D 08 Ø4,0*30mm I 01 Left slide 300mm H 01 J 01 Right slide 300mm Step 10 P.
PAGE 10
Step 11 To adjust the drawer front position: Loosen the screw (part C) you used to install the drawer runner (either parts H or I) in step 2, to the side panel (parts 02 or 03), depending on the side (left or right), as shown. With the screw (part C) loosened, you can make the necessary slight adjustments (up or down) to the drawer runner to achieve the proper drawer alignment.