Assembly Instruction Sheet
Package Contents
Warnings and Cautions
1of2
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar
Assembly
x1
D
Diffuser
x1
C
Shade
x1
B
Fixture Body
x1
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
(3)A19MediumBasebulb100WMaximum,Alternatebulb(3)23WCFL.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the
Ceiling Canopy over the outlet
box. Align the holes in the
Ceiling Canopy with the
mounting screws, then attach
the Ceiling Canopy using the
previously removed mounting
balls. Hand tighten until snug.
Figure 4
Mounting
Screw
Ceiling
Canopy
STEP 5 - Install Shade,
Fixture Body and Side
Arm together
A. Place Shade (C) and
Diffuser (D) into the
Shade Holder (E)
properly.
B. Pass the Bolt on the Side
Arm through the hole on
the Shade Holder (E),
secure by threading Lock
Ball (F) onto the Bolt.
Hand tighten until sung.
C. This fixture uses
standard bulb with a
medium screw base.
Maximum 100 watts.
Insert bulb and screw
snugly into place.
Your fixture is now
assembled and ready to
use. Enjoy!
Figure 5
E
Shade
Holder
x1
F
Lock Ball
x3
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar
Assembly (A). Attach the Crossbar Assembly
(A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
STEP 2 Fit Ceiling Canopy to
Crossbar Assembly
-
A. Unfold Support Arms of the
Fixture Body (B) to proper
locations. (Refer to Shade
Orientation)
B.
(B) to the
Remove mounting balls from
the Crossbar Assembly (A).
Fit the Canopy
Crossbar Assembly (A) and
Mounting Screw
Hex Nut and
Lock Washer
B
Mounting
Ball
Figure 2
A
secure with mounting balls. Note: The Canopy
should be snug against the and the
mounting balls. If
(B) ceiling
not, adjust the length of the
nipple on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and
lock washer and then screwing the mounting
screws in or out of the crossbar until the
correct length is achieved. Once the Canopy
(B) is secure, remove the mounting ball and
ceiling canopy and proceed to Step 3.
A
Mounting
Ball
A
F
E
C
D
Bolt
Socket
Bulb
Side Arm
Assembly Instruction Sheet
Pleasegoto our website for product cleaning tips. Go to the Care + Maintenance selection.
Thank you for purchasing our product.
Need assistance with parts or assembly? Call our customer service or visit us on-line .