ASSEMBLY INSTRUCTION UPHOLSTERED STORAGE PLATFORM QUEEN BED Headboard Footboard Center Support Bar Rail Section - Front 1PC Rail Section - Rear 1PC Center Rail - Front / Rear 1PC Center Support Leg 2PCS Drawer Front Board 2PCS Drawer Side Board 2PCS Drawer Back Board 2PCS Drawer Bottom Frame 4PCS Drawer Bottom Board 8PCS Fabric Cover 4PCS Slat 4PCS Side Slat Connector 4PCS Center Slat Connector 1PC Drawer Board Connector 24PCS Wheel 24PCS Bracket 120*42*27*2mm 12PCS Bracket 27*27*30*2mm
Bolt 3/16"*8mm Bolt 1/4"*13mm Bolt 1/4"*19mm Bolt 1/4"*34mm 48PCS Nut 3/16"*6.5mm 8PCS Washer Ø16mm 4PCS L-Allen Key 4mm 16PCS Ratchet Tool 4mm 8PCS 48PCS 1PC 1PC These pages list all the contents included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
How to Use the Ratchet Tool (AF) 1. Before assembling the furniture, please adjust the lock as needed. Lock on the right to loosen bolts! Lock on the left to tighten bolts! 2. Tighten or loosen bolts. Tighten bolts: Locate the turncap and rotate it clockwise to screw the bolt quickly until it cannot be rotated any more. Then start rotating the handle clockwise to finalize tightening the bolt. Turncap Handle Loosen bolts: Rotate the handle counterclockwise to loosen the bolt.
Attach the Bracket (S) to Center Support Bar (C), insert the Bolt (U), turn the Ratchet Tool (AF) to tighten them. S C S AF S C U Attach the Bracket (S) to the Rail Section - Front (D) and Rail Section Rear (E), insert the Bolt (V), turn the Ratchet Tool (AF) to tighten them. AF E V C S D E S D C D S E Cover the Fabric Cover (M) to the Headboard (A).
Attach the Center Support Leg (G) to the Center Rail - Front / Rear (F), insert the Bolt (V), turn the Ratchet Tool (AF) to tighten them. G AF V F G F Attach the Center Rail - Front / Rear (F) to the Headboard (A) and the Footboard (B), insert the Bolt (V), turn the Ratchet Tool (AF) to tighten them. Then attach the Center Rail - Front / Rear (F) to the Center Support Bar (C), insert the Bolt (W), turn the Ratchet Tool (AF) to tighten them.
7 Attach the Wheel (R) to the Drawer Bottom Frame (K), insert the Bolt (Y), turn the Ratchet Tool (AF) to tighten them. R AF Y K R R K R R R 8 Attach the Drawer Front Board (H) to the Drawer Bottom Frame (K), insert the Bolt (AB), turn the Ratchet Tool (AF) to tighten them. H K AB AF H K 9 Attach one Drawer Side Board (I) to the Drawer Bottom Frame (K), insert the Bolt (X) and Washer (AD), turn the Ratchet Tool (AF) to tighten them.
10 Insert the Drawer Bottom Board (L) to the assembled Drawer Side Board (I). I L I L 11 Insert another Drawer Side Board (I) to the Drawer Bottom Board (L) first, and attach the Drawer Side Board (I) to the Drawer Bottom Frame (K), then insert the Bolt (X) and Washer (AD), turn the Ratchet Tool (AF) to tighten them. I I AF L AD X K L I K 12 Attach the Drawer Back Board (J) to the Drawer Bottom Frame (K), insert the Bolt (X) and Washer (AD), turn the Ratchet Tool (AF) to tighten them.
Attach the Bracket (T) to the assembled drawer, insert the Bolt (Z), turn the Ratchet Tool (AF) to tighten them. And insert the Bolt (Y), Washer (AD) and Nut (AC), turn the L-Allen Key (AE) and Ratchet Tool (AF) to tighten them. H H AD I T AE AF Z AC AF Y T I T H I T I 14 Insert the Bolt (AA) and Washer (AD) to the back of Drawer Front Board (H), turn the Ratchet Tool (AF) to tighten them. H AD AA AF H 15 Align drawers with the bed frame and push them into the bed.
When pull out the drawers, lift the drawers first in order to make the Pins released from the Slots freely, then pull the drawers toward outside. DO NOT PULL OUT THE DRAWERS DIRECTLY. Pin Slot Cleaning & Care Treat surface with care. Surface is resistant to scratches but is not scratch resistant. Clean surfaces with a dry or damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time. Periodically check that all connections are tight.
