Assembly Instructions

ManualsBrandsMercury Row ManualsAll Shoe Storage12 Pair Shoe Storage Cabinet

Table Of Contents

EASY

DIFFICULT

Page 1 of 15

ASSEMBLY RATING

The Assembly Rating is a 5-point system that

shows the degree of effort needed in

assembling a specific product (with 1 being

easy and 5 being difficult). For most

products,two persons are recommended.

Hammer

Phillips Screwdriver

Tools Required for Assembly:

2 PERSONS RECOMMENDED

(Not Included)

Summary of content (14 pages)

PAGE 1
ASSEMBLY RATING Tools Required for Assembly: The Assembly Rating is a 5-point system that shows the degree of effort needed in assembling a specific product (with 1 being easy and 5 being difficult). For most products,two persons are recommended.
PAGE 2
Thank you for your purchase! We hope you wiIl enjoy your new product for many years to come. Our commitment to providing quality products does not simply end when a purchase is made. We stand behind our products and will provide any support needed in order for you to fully enjoy your purchase. Your satisfaction is the greatest recognition we could have. Because we value your trust in our company,we will do our best to meet your service expectations.
PAGE 3
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE. BASIC ASSEMBLY TECHNIQUES It is highly recommended that the assembly should be done near the area of its intended location. Make sure you have enough space to move around during the assembly. Position each part correctly and insert screws or bolts into their respective holes by hand tighten or using the proper hand tool.
PAGE 4
Unless you are particularly adept at assembling flat-pack/knock-down furniture, we understand building ready-to-assemble furniture can be a frustrating experience for some. To help avoid confusion and to make the assembly process quicker and smoother, we have provided some helpful tips. Before you begin the assembly, please read the following : 1. 2. 3. 4. 5. 6. 7.
PAGE 5
Note:Every cam lock bolt must have a cam lock connector in order to fasten the parts together. (1) Align the cam connector with its side opening (or arrow) pointing to the small driIIed hole. Secure the threded end of the cam bolt by using a screwdriver. Tun right (clokwise) to tighten. (3) (2) Insert the cam lock bolt into the pre-drllled hole above the cam connector. Two parts should fit snugly against each other.
PAGE 6
(1) 1pc (2) 1pc (3) 1pc (4) 1pc (5) 1pc (6) 1pc (7) 1pc (8) 3pcs (9) (10) (11) (12) (13) (14) (15) (16) 1pc 1pc 2pcs 1pc 1pc 1pc 1pc 2pcs Before you begin,please read"Assembly and Care Advice","Pre-Assembly Introduction"and "Cam Lock Fastener Assembly Instructions".
PAGE 7
A B C D E F G H I J K L M N O P Q R S T U L29 φ15 φ8х25 φ22 ∅4х40 M6х25 φ16 ∅3х16 ∅5х15 301A ∅4х16 96# ∅4х22 16pcs 16pcs 9pcs 8pcs 4pcs 6pcs 4pcs 36pcs 1pc 2pcs 12pcs 4pcs 16pcs 2pcs 4pcs 1pc 2pcs 1pc 1pc 1pc 1pc Due to the size and/or weight of this product,it is highly recommended that the assembly should be done near the area of its intended location.Make sure you have enough space to move around during the assembly.
PAGE 8
Page 8 of 15
PAGE 9
Page 9 of 15
PAGE 10
Ax2 Bx2 Ax2 Bx2 Fx6 Page 10 of 15 Cx1
PAGE 11
Gx4 Hx36 Page 11 of 15
PAGE 12
Ix1 Jx2 Kx12 Page 12 of 15
PAGE 13
Mx16 Lx2 Page 13 of 15
PAGE 14
Page 14 of 15