USE AND CARE GUIDE
Table of Contents Safety Information ....................................................................................................................................... 2 Warranty ...................................................................................................................................................... 2 Pre-Installation ............................................................................................................................................
Pre-Installation PLANNING INSTALLATION Read all instructions before assembly. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase. NOTE: The lamp requires the use of one 120V, 60HZ, 40-Watt max, medium-base type A bulb (not included). Do not exceed the recommended wattage.
Pre-Installation (continued) PACKAGE CONTENTS C B A Part Description Quantity A B C Socket ring Shade 1 1 Lamp body 1 4
Using power cord instructions 1. Unpack the lamp and remove the mounting plate □ Carefully organize and place all parts on a smooth, flat surface. line up all of the parts according to the installation diagram. □ Remove the mounting plate (BB) from back of the backplate by unscrewing two mounting screws (DD). BB DD Backplate NOTE: If using power cord follow instructions below. If wiring to an outlet box proceed to outlet box installation instructions. 2.
Using power cord instructions (continued) 3. Hanging the lamp body □ Raise the lamp body (C) to wall, align the holes in backplate with the holes in mounting plate (BB), and then secure the backplate to the wall with three mounting screws (DD). C BB DD Backplate 4. Installing the cord cover Optional, if not using cord covers skip to step 5. □ Place the cord channel (II) on the wall and mark the holes. □ Drill pilot holes on the marked spots and insert plastic anchors (FF).
Using power cord instructions (continued) 5. Assembling shade and installing the bulb □ Swing the swing arm, if the swing arm is hard to swing or have abnormal sound, put a drop of WD-40 or similar product on the joint and let it sit overnight. dry with a soft cloth. □ Remove the socket ring (A) from the socket by unscrewing the socket ring (A). □ Place the shade (B) over the socket and secure with the socket ring (A). □ Prior to installing the bulb, inspect socket for silica packet.
Outlet box installation instructions 1. Removing the power cord The power cord is the wire that enters through the bottom of the backplate. □ Remove the two wire nuts that connect to power cord by twisting counter clockwise. (see diagram) □ Untie safety knot and pull power cord out through bottom of the backplate. □ Remove the grommet and use the hole plug (HH) to cover the hole in backplate. Ground wire Backplate Wire nuts (remove) Safety knot Grommet Power cord HH (Hole plug) 2.
Outlet box installation instructions (continued) 3. Connecting the wires □ Install the fixture bare copper wire (1) under the green ground screw (EE) on the mounting plate (BB). □ Connect the fixture bare copper wire (1) to the green (or bare, or green & yellow) supply ground wire (2) in the outlet box using a wire nut (AA). □ Connect the white fixture wire (3) to the white (or ribbed) supply wire (4) in the outlet box using a wire nut (AA).
Outlet box installation instructions (continued) 5. Assembling shade and installing the bulb □ Swing the swing arm, if the swing arm is hard to swing or have abnormal sound, put a drop of WD-40 or similar product on the joint and let it sit overnight. dry with a soft cloth. □ Remove the socket ring (A) from the socket by unscrewing the socket ring (A). □ Place the shade (B) over the socket and secure with the socket ring (A). □ Prior to installing the bulb, inspect socket for silica packet.
Important safety instructions □ This portable lamp has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. never use with an extension cord unless plug can be fully inserted. Do not alter the plug. Care and Cleaning □ Clean the lamp with a soft, dry cloth.
