ASSEMBLY INSTRUCTIONS 4-DRAWER CHEST 2 Hours == 0 =0 ASSEMBLY 2 Person Assembly Tme Tools Required Phillips Flat — REQUIREMENTS Assembly (Approximate) {Not Provided) Screwdriver Screwdriver Mallet Thank you for purchasing our product Please refer and use this assembly instruction to assemble the product. Contact our customer service department in case there are any missing or damage parts or hardware, Replacement parts are normally shipped within 2 or 3 days.
ASSEMBLY INSTRUCTIONS 4-DRAWER CHEST CSK SCREW V SHAPE METAL LEG B> M3.5 X 12MM HIMMLER 4 CSK SCREW BACK PLY STOPPER 10 CSK SCREW WEBBING STRAP M4.5 X 32MM 16 P (12X 12 X 145 MM) 1 EURO SCREW M6 X 13MM | 8 Q GLUE 3 WOOD DOWEL 24 26 X 20MM Procedure to Separate Glide Track (1) WOOD DOWEL 10 and Glide Runner {Z2) of Drawer Glide X 25MM ANGLE CAM-BOLT 8 CAM-BOLT 16 24X8.
PARTS LIST ASSEMBLY OVERVIEW PARTS LIST NO. PART NAME QTY ||NO.
Instructions For Fastening New/Revised Version CAM-BOLT and CAM-LOCK Tools Required INSERTING AND TIGHTENING CAM-BOLT CAM-BOLT l CAM LOCK SHOULDER / X > ?p&\ e o . Shoulder is flushed {on Place Cam-bolt on per-driled the same level) with the Shoulder is above the panel. hole and screw In vertically panel. Place Cam-bolt on the designated per-drilled holes on the panel. Use a Phillips Screwdriver to screw-in Cam-bolt vertically until shoulder is flushed {on the same level) with panel.
STEP 1 a) Lay Drawer Left & Right Panels (7 & 8), Drawer Support Rail {10), Center Support Rail (4}, and Back Support Rail {5} as shown on a material that does not scratch or damage the parts. Next, identify the designated holes for wood dowel on each part. b) Apply a small amount of Glue (Q) into the designated hole and insert Wood Dowel (E). Use a mallet fo tap in wood dowel, if necessary.
STEP 2 a)Lay Side Panels (1}, Top Panel (2), Bottom Panel (3) and Drawer Front Panels (6} with the groove side facing up as show non a material that does not scratch or damage the parts. Next, identify the designated holes for Cam-bolt (H) on each part. b} Place Cam-bolt {H) on the designated hole and use a Phillips Screwdriver to screw-in Cam bolt. Refer to page 4 for instructions on tightening cam-bolts.
STEP 3 Step 3A (Refer to Drawing 3A} Attach Drawer Left & Right Panels Drawer Back Panel as shown note the groove on each panel is at the bottom. Use Phillips Screwdriver to drive Screw (C) to fasten side panels to back panel. Do not tighten screws completely until both screws are in place on each panel. Attach Drawer Support Rail {10) from STEP 1 to via Wood Dowels on {10).
STEP 4 a)Place drawer on its side. Locate pilot holes on Drawer Left & Right Panels {7 & 8) for fastening Glide Runner(72). b)Position 72 to align the round screw holes on 72 (refer to enlarged drawing) to the pilot holes c)Use Screw {A) to fasten 22 to the Drawer Left & Right Panels. Use a Phillips Screwdriver to drive (A). Do not tighten {A) completely until all 3 screws are in place.
STEP 5 a)Place Side Panel (1) with inside-face facing up as shown on a material that does not scratch or damage the part. b) Locate pilot holes on (1} for fastening Glide Track (Z1). c) Position Z1 to align the designated screw holes on Z1 (refer to enlarged drawing) to the pilot holes on (1). Note: the front & rear of Z1 has to be aligned with front and back of the Side Panel. d)Use Screw (A} fo fasten 71 to the Side Panel. Use a Phillips Screwdriver to drive (A).
STEP 6 a)Lay Drawer Top & Bottom Panels (2 & 3) with the inside-face facing up as shown on a material that does not scratch or damage the parts. b} Insert one end of Angle Cam-bolt (G} into each hole on the edge of the panels.
STEP 7 a)Position a piece of Side Panel (1), from STEP 5, with the groove edge at the bottom as shown on a material that doses not scratch the bottom edge. Next, apply a small amount of Glue [Q) info each hole near the bottom comer and beside the cam-bolt. b) Attach Back Support Rail {5} from STEP 1 to Side Panel via Cam-bolt and Wood Dowel as shown. Check that the edge of {5) with groove are facing inwards and forwards each other.
STEP 8 a)Fit Back Pane! (12} between Back Support Rails {5) by inserting the horizontal edges of (12} into the groove on {5). Check that the vertical edge of (12) is 'Inserted into the groove on the existing Side Panel (1). a)Position the Side (Right} Panel (1), from STEP 5, to minor the installed Side Panel. b) Apply a small amount of Glue {Q) into each hole near the bottom comer and beside the com bolt, and into the hole above the cam-bolt at the center and near the top edge of Panel.
STEP 10 a)Align Top Pane! (2) to Side Panels (1) as shown. Next, apply a small of Glue (Q) into the designated holes for Wood Dowels on (2). b)Firmly attach (2) to (1) via Angle Cam-bolt and Wood Dowels c)Insert Cam-lock (J) into designated holes on inside-face of (1), then turn clockwise to lock onto cam-bolt. d)Use the procedures above to install Bottom Panel (3).
STEP 11 a)Position each Metal Leg (M) to align the screw holes on each leg to the pilaf holes at Bottom Panel {3) as shown. Note: the angled V-shape of the leg faces inward. b)Use a Phillips Screwdriver to drive Screw (D} fo fasten each leg to Bottom Panel. Do not tighten screws completely until both screws are in place on each leg. c)Position the assembly right-side up after all the of the legs are installed.
T met Slide Holier on Glide Track (Z1) to the é Front. Step 11-3 TOP VIEW TOP VIEW BODY BODY 1 + 1 LEFT DRAWER RIGHT LEFT DRAWER RIGHT v X Align 72 on each side of the drawer to Z1 on the Left and| Right Panels. Ensure the positions of 72 are correct {not| fetid or angled). up or down. Refer to the illustrations above. 112 and & [b) above. a) With 22 position comely. line-up the drawer squarely, and push in the left and right side of the drawer af the some time.
STEP 13 a)Insert Back Stopper (M) at the comers as shown to fit into the groove and against Back Panel {9) and fasten (M) with Screw (B). b)Fasten one end of Webbing Strap (P) with Screw (B} to the back edge of Top Panel (2). STEP 14 WALL g/9/86/8 Al 1. WALL PLUG & SCREW ARE NOT SUPPLIED WITH THIS PRODUCT AS DIFFERENT WALL MATERIALS REQUIRE DIFFERENT TYPES OF FIXING HARDWARE. SUITABLE ANCHORING HARDWARE FOR THE TYPE OF WALL MUST BE USED TO MOUNT THIS PRODUCT TO THE WALL. 2.
