User's Manual

Quantum 1000 Base Station User
5.
Base Station Bring
5.1 Overview
This section describes how the operator may power
system initialization. The
PureWave
and ensure
general system integrity
5.2
Connect to the Base Station
There are three RJ45 Ethernet ports to connect and hence access the Base Station.
RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the
box” configuration and debug purposes.
E-
NET 1: This Gigabit Ethernet port provides the data traffic backhaul interface that should be connecte
to the Service Provider’s network equipment. This port allows in
E-
NET 2: This Gigabit Ethernet port provides an out
can be used for daisy chaining to another bas
Camera.
The procedure to connect to the Base Station is:
•
Terminate the antenna ports ANT 1 and ANT 2 as directed.
•
Connect and Power on the Base Station.
•
Connect a “straight” Cat 5 Ethernet cabl
directly to your PC or to your switch.
•
To get access to Base Station CLI (Command Line Interface) you will need the following
hardware that come with the install kit. These are as follows:
 RJ45 cable.

DB9 male connector (Modem Adapter).

DB9 female to DB9 female adapter.
Optional: Serial to USB connector. Most laptop nowadays comes with USB connection instead of serial
connection. If your PC/laptop has serial connection then you won’t need this adapter. If not, then you will
need to get serial to USB adapter to access the
Figure
Quantum 1000 Base Station User
Guide
Rev 1.1, Page
Base Station Bring
-up
This section describes how the operator may power
-
up the PureWave Base Station and verify proper
PureWave
Base Station CLI (Command Line Interface)
will be used to confi
general system integrity
.
Connect to the Base Station
There are three RJ45 Ethernet ports to connect and hence access the Base Station.
RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the
box” configuration and debug purposes.
NET 1: This Gigabit Ethernet port provides the data traffic backhaul interface that should be connecte
to the Service Provider’s network equipment. This port allows in
-
band management of the Base Station.
NET 2: This Gigabit Ethernet port provides an out
-of-
band management interface. In addition, this port
can be used for daisy chaining to another bas
e station or to connect to an external device such as a web
The procedure to connect to the Base Station is:
Terminate the antenna ports ANT 1 and ANT 2 as directed.
Connect and Power on the Base Station.
Connect a “straight” Cat 5 Ethernet cabl
e between the E-
NET 1 port on the Base Station and the
directly to your PC or to your switch.
To get access to Base Station CLI (Command Line Interface) you will need the following
hardware that come with the install kit. These are as follows:
DB9 male connector (Modem Adapter).
DB9 female to DB9 female adapter.
Optional: Serial to USB connector. Most laptop nowadays comes with USB connection instead of serial
connection. If your PC/laptop has serial connection then you won’t need this adapter. If not, then you will
need to get serial to USB adapter to access the
BS CLI (figure 57).
Figure
57 – Serial to USB adapter (DB9 Male)
Rev 1.1, Page
51 of 70
up the PureWave Base Station and verify proper
will be used to confi
gure
RS232: This is the serial interface to the Base Station. This interface will be primarily used for “out of the
NET 1: This Gigabit Ethernet port provides the data traffic backhaul interface that should be connecte
d
band management of the Base Station.
band management interface. In addition, this port
e station or to connect to an external device such as a web
NET 1 port on the Base Station and the
To get access to Base Station CLI (Command Line Interface) you will need the following
Optional: Serial to USB connector. Most laptop nowadays comes with USB connection instead of serial
connection. If your PC/laptop has serial connection then you won’t need this adapter. If not, then you will