Product Manual
Table Of Contents
- Notice to Users of This Manual
- Precautions
- Replacement Parts
- Cleanliness and Care of Product
- Copyright and Trademark Information
- Manual Outline
- Section 1A - Specifications
- Table of Contents
- Model Specifications
- Ignition Specifications at 20 °C (68 °F)
- Charging and Starting Specifications
- Fuel System Specifications
- Cylinder Block/Crankcase Specifications
- Piston Specifications
- Cylinder Head Specifications
- Oil System Specifications
- Cooling System Specifications
- Power Tilt Specifications
- Gearcase Specifications
- Section 1B - Maintenance
- Table of Contents
- Cleaning Care
- Inspection and Maintenance Schedule
- Battery Inspection
- Flushing the Cooling System
- Fuel System
- Fuse Replacement - Electric Start Models
- Spark Plug Inspection and Replacement
- Timing Belt Inspection
- Engine Oil
- Corrosion Control Anodes
- Propeller Replacement
- Gearcase Lubrication
- Lubrication Points
- Storage Preparation
- Section 1C - General Information
- Table of Contents
- Recording Serial Number
- Model Year Production Code
- Engine Component Identification - Manual Start Model
- Engine Component Identification - Electric Start Model
- Following Complete Submersion
- Fuel Requirements
- Painting Procedures
- Emissions
- Shipping of Hazardous Material (HazMat) and Engine/Components Containing Hazardous Material
- Section 1D - Outboard Installation
- Section 1E - General Troubleshooting
- Table of Contents
- Conditions Affecting Performance
- Compression Check
- Cylinder Leakage Test
- Guardian Protection System
- Warning System
- Troubleshooting without a Computer Diagnostic System (CDS)
- Troubleshooting with CDS G3
- Accessing ECM Information with CDS G3
- CDS G3 Screens (10/15/20 EFI)
- Engine Control Module Pinout
- Fault Codes
- Section 2A - Ignition
- Table of Contents
- Ignition Specifications at 20 °C (68 °F)
- Ignition Theory of Operation
- General Troubleshooting
- Engine Control Module (ECM)
- Wire Color Code Abbreviations
- Sensors
- Ignition Components
- Section 2B - Charging and Starting Systems
- Section 3A - Fuel System Operation
- Section 3B - Troubleshooting and Diagnostics
- Section 3C - Service Procedures
- Section 4A - Cylinder Block/Crankcase
- Table of Contents
- Cylinder Block/Crankcase Specifications
- Piston Specifications
- Cylinder Block and Crankcase Components
- Crankshaft Components
- Powerhead Removal
- Cylinder Block Disassembly
- Powerhead Cleaning, Inspection, and Repair
- Powerhead Assembly
- Powerhead Installation
- Section 4B - Cylinder Head
- Section 4C - Oil Pump
- Section 4D - Cooling System
- Section 5A - Clamp/Swivel Bracket and Driveshaft Housing
- Table of Contents
- Clamp Bracket Components (Power Tilt)
- Clamp Bracket Components (Manual Tilt)
- Steering Arm and Copilot Components
- Driveshaft Housing Components
- Driveshaft Housing Cover Components
- Driveshaft Housing Covers
- Front Cowl
- Idle Exhaust Port Cover
- Powerhead/Midsection Assembly Separation
- Engine Mount Replacement
- Clamp Brackets, Swivel Bracket - Power Tilt Models
- Clamp Brackets, Swivel Bracket - Manual Tilt Models
- Driveshaft Housing Removal
- Driveshaft Housing Installation
- Shift Operation
- Kicker Strap (Tiller Handle Model)
- Section 5B - Power Tilt
- Table of Contents
- Power Tilt Specifications
- General Troubleshooting
- Power Tilt - General Information
- Power Tilt Components
- Theory of Operation
- Power Tilt Features and Operation
- Check Fluid and Purge the Power Tilt System
- Cowl-Mounted Tilt Switch
- Troubleshooting the Power Tilt System
- Power Tilt Removal
- Manual Release Valve Removal and Repair
- Power Tilt Motor
- Power Tilt Pump
- Power Tilt Installation
- Section 6A - Gear Housing (2.15:1)
- Table of Contents
- Gearcase Specifications
- Gear Housing and Driveshaft
- Propeller Shaft
- General Service Recommendations
- Draining and Inspecting Gear Housing Lubricant
- Gear Housing Removal
- Gear Housing Disassembly
- Gear Housing Assembly
- Pinion Bearing Installation
- Forward Gear Bearing Installation
- Bearing Carrier Assembly
- Water Pump Base Assembly
- Propeller Shaft Assembly
- Pinion Gear and Driveshaft Installation
- Forward Gear Backlash
- Shift Shaft and Water Pump Base Installation
- Water Pump Cover Assembly
- Propeller Shaft and Bearing Carrier Installation
- Gear Housing Installation
- Propeller Installation
- Section 7A - Throttle and Shift Linkage
- Section 7B - Tiller Handle
- Section 8A - Recoil Starter
- Section 9A - Color Diagrams
Powerhead
Section
4A - Cylinder Block/Crankcase
Table of Contents
Cylinder Block/Crankcase Specifications...........................4A-2
Piston Specifications
..........................................................4A-3
Cylinder Block and Crankcase Components..................... 4A-4
Crankshaft Components.................................................... 4A-6
Powerhead Removal..........................................................4A-8
Cylinder Block Disassembly.............................................4A-10
Electrical Component Removal................................ 4A-10
Throttle Body Removal............................................. 4A-12
Crankshaft Timing Gear Removal............................ 4A-12
Thermostat and Exhaust Cover Removal.................4A-13
Oil Strainer Removal.................................................4A-14
Crankcase and Crankshaft Removal........................ 4A-14
Piston Disassembly.................................................. 4A-16
Powerhead Cleaning, Inspection, and Repair..................4A-16
Flywheel....................................................................4A-16
Crankshaft Timing Gear............................................4A-17
Timing Belt................................................................4A-17
Anode....................................................................... 4A-17
Measuring Cylinder Bore.......................................... 4A-17
Piston Measurements............................................... 4A-17
Connecting Rod Measurements............................... 4A-19
Crankshaft................................................................ 4A-20
Crankcase Main Bearings.........................................4A-20
Connecting Rod Oil Clearance................................. 4A-23
Powerhead Assembly...................................................... 4A-24
Piston Assembly....................................................... 4A-24
Piston Ring Installation............................................. 4A-24
Piston Installation......................................................4A-25
Crankshaft Installation.............................................. 4A-26
Crankshaft Timing Gear Installation......................... 4A-28
Thermostat, Exhaust Cover, and Anode Installation
.............................................................................. 4A-28
Oil Strainer Installation..............................................4A-30
Throttle Body Installation.......................................... 4A-30
Electrical Component Installation............................. 4A-31
Powerhead Installation.....................................................4A-33
Cylinder Block/Crankcase
90-8M0125265 eng NOVEMBER 2017 © 2018 Mercury Marine Page 4A-1
4
A