Product Manual
Table Of Contents
- 8/9.9 and 9.9 Command Thrust/ProKicker FourStroke
- Welcome
- Read This Manual Thoroughly
- Notice
- Warranty Message
- Copyright and Trademark Information
- Identification Records
- General Information
- Boater's Responsibilities
- High-Speed and High-Performance Boat Operation
- Outboard Remote Control Models
- Remote Steering Notice
- Lanyard Stop Switch
- Protecting People in the Water
- Passenger Safety Message - Pontoon Boats and Deck Boats
- Wave and Wake Jumping
- Impact with Underwater Hazards
- Exhaust Emissions
- Safe Boating Recommendations
- Recording Serial Number
- Model Year Production Code
- 8/9.9 FourStroke Specifications
- Component Identification - Standard Models
- Component Identification - Command Thrust/ProKicker Models
- Installation
- Boat Horsepower Capacity
- Start in Gear Protection
- Selecting Accessories for Your Outboard
- Low Permeation Fuel Hose Requirement
- Mercury Marine Validated Engine Mounting Hardware
- Installing Outboard
- Remote Control Installation
- Steering Link Rod Fasteners
- Remote Wire Harness Connection
- Control Cable Installation
- Battery Installation - Electric Start Models
- Battery Connections
- Propeller Installation
- Transporting
- Fuel and Oil
- Features and Controls
- Operation
- Prestarting Check List
- Operating in Freezing Temperatures
- Operating in Saltwater or Polluted Water
- Operating Outboard as an Auxiliary Engine
- Prestarting Instructions
- Engine Break-in Procedure
- Starting the Engine - Tiller Handle Models
- Starting the Engine - Remote Control Models
- Starting a Hot Engine
- Gear Shifting
- Stopping the Engine
- Emergency Starting
- Maintenance
- Cleaning Care Recommendations
- EPA Emission Regulations
- Inspection and Maintenance Schedule
- Maintenance Schedule Decal Icons
- Maintenance Schedule Decal
- Flushing the Cooling System
- Top Cowl Removal and Installation
- Battery Inspection
- Exterior Care
- Fuel System
- Steering Link Rod Fasteners
- Corrosion Control Anode
- Propeller Replacement
- Fuse Replacement - Electric Start Models
- Spark Plug Inspection and Replacement
- Timing Belt Inspection
- Changing Engine Oil
- Lubrication Points
- Gearcase Lubrication
- Checking Power Tilt Fluid
- Submerged Outboard
- Storage
- Troubleshooting
- Owner Service Assistance
- Maintenance Log
- General Information
Routine cleaning of the remote control external surfaces is recommended to
prevent a buildup of salt and other environmental debris. Use a cloth towel
which has a sufficient amount of fresh water to dissolve and remove salt or
mineral deposits.
When water marks cannot be removed with a damp cloth, mix a 50/50 solution
of warm water and isopropyl alcohol to clean the remote control. Do not use
acetone, mineral spirits, turpentine type solvents, or ammonia based cleaning
products. The use of strong solvents or detergents may damage the coating,
the plastics, or the rubber components on the remote control.
CLEANING CARE FOR TOP AND BOTTOM COWLS
IMPORTANT: Dry wiping (wiping the plastic surface when it is dry) will result in
minor surface scratches. Always wet the surface before cleaning. Do not use
detergents containing hydrochloric acid. Follow the cleaning and waxing
procedure.
Cleaning and Waxing Procedure
1. Before washing, rinse the cowls with clean water to remove dirt and dust
that may scratch the surface.
2. Wash the cowls with clean water and a mild nonabrasive soap. Use a soft
clean cloth when washing.
3. Dry thoroughly with a soft clean cloth.
4. Wax the surface using a nonabrasive automotive polish (polish designed
for clear coat finishes). Remove the applied wax by hand using a clean
soft cloth.
5. To remove minor scratches, use Mercury Marine Cowl Finishing
Compound (92‑859026K 1).
CLEANING CARE FOR THE POWERHEAD (SALTWATER USE)
If the outboard is operated in saltwater, remove the top cowl and flywheel
cover. Inspect the powerhead and powerhead components for salt buildup.
Wash off any salt buildup from the powerhead and powerhead components
with fresh water. Keep water spray out of the air filter/intake and alternator.
After washing, allow the powerhead and components to dry. Apply Quicksilver
or Mercury Precision Lubricants Corrosion Guard spray on the external metal
surfaces of the powerhead and powerhead components. Do not allow the
Corrosion Guard spray to come in contact with the alternator drive belt or belt
pulleys.
IMPORTANT: Do not allow lubricant or Corrosion Guard spray to come in
contact with the alternator drive belt or the belt pulleys. The alternator drive belt
could slip and be damaged if it becomes coated with any lubricant or Corrosion
Guard spray.
MAINTENANCE
74 eng