SMART VIDEO DOORBELL QUICK START GUIDE SDC56 www.ikuu.com.
Introduction This smart video doorbell is designed for use in homes, apartments, offices, garages and sheds. It’s easy to set up and operate, giving you and your family the security and peace of mind that you deserve. You can monitor your video doorbell remotely through the Mercator Ikuü app, which can be downloaded for free from the Apple App Store and Google Play Store. Make sure to fully charge your video door bell unit prior to installation.
Identification Light Sensor/ Infrared LEDs Detects low light and turns on the infrared lights which allow the camera to capture both day and night images. Camera Lens 1080p HD, with 120° angle of view Speaker Two way audio Microphone Status Light Entering Pairing Mode Purple, red, and blue followed by the doorbell announcing ‘system reset’. Grub Screw Location Pairing Mode Flashing blue. The doorbell is now in pairing mode. During Pairing Red, purple and blue then off.
Preparing Your Device Remove the battery compartment cover. Pull off the isolation strip to allow the battery to make electrical contact. Reinstall the battery cover. Note: Ensure the battery polarity (+/-) matches the battery compartment sign. Set Up the App 1. Download the Mercator Ikuü app. 2. Tap ‘create new account’ or ‘log in to account’. 3. Follow the in-app prompts and tap ‘OK’. Connect Your Video Doorbell to the App 1 Log in to the Mercator Ikuü app.
Connect Your Video Doorbell to the App (cont.) 3 4 Select ‘Doorbell’ from the sidebar, and then tap the Video Doorbell icon. When the prompt appears, tap ‘next step’. 5 6 Enter your Wi-Fi name and password, then tap ‘Confirm’. When the prompt appears, tap ‘Continue’.
Connect Your Video Doorbell to the App (cont.) 7 8 Place the camera eye over the QR code to scan (holding the camera 15cm away from your mobile screen). When you hear the prompt, tap ‘I Heard a Prompt’. The app will begin connecting to your video doorbell. When it reaches 100%, you will be taken to the product’s settings page. 9 10 Update the name of the device and assign it to a room (optional), then tap ‘Done’.
Doorbell Functions Take a photo of the live video feed, which will be saved to the photo album. Speak through the doorbell speaker via your phone microphone. Take a video of the live video feed, which will be saved to the photo album. Event Recording only. Review camera footage from the SD card (if installed). Adjust motion detection settings. View previously saved photos and video recordings. You can download these to your local mobile device. Adjust the date when reviewing playback.
Pairing Your Indoor Chime Unit 1. In a location near your door and with good Wi-Fi coverage, power on your indoor chime unit with 3 x 1.5V “AA” type batteries (Alkaline batteries recommended). Press the “Volume” button for 5 seconds till the melody changes. Press the doorbell button to test the indoor chime unit. If the chime doesn’t sound please refer to step 3 below. 2. If you need to un-pair your chime unit from the video doorbell press and hold the chime Volume button for approximately 30 seconds.
1. Drill appropriately sized hole and insert wall plug (if required). 2. Fit screw provided, ensuring that there is a gap of approx. 3mm between mounting surface and head of screw to enable attachment of unit. 3. Attach Chime Unit by sliding ‘Keyhole’ shaped slot over screw. Alternatively unit can be left unmounted, in this form it can also be used as a portable paging device. Carry it with you around the house as needed.
1. Plug DC power adaptor into a power source and connect it with doorbell using provided USB cable (Fig 2 & 3). 2. During charging, the charging indicator should turn red. We suggest charging the doorbell for 6-8 hours before installation. INSTALLATION Note: Product should be fully charged before installation. FIG. 02 1. Mark screw position through the bracket holes (Fig 4). 2. Fix the mounting bracket on the wall by using the included screws and wall plugs. 3.
App Features Want more from your products? The Mercator Ikuü app can help you to customise your smart products any way you like. Detailed guides on these features can be found at www.ikuu.com.au. Rooms Separate your products within the app for easy control based on their location. Scenes Control multiple products from any room at the same time. Automation Create triggers that allow products to complete actions automatically. These triggers can be based on time, sensors, or even other products.
Warranty Mercator guarantees this product against defects of materials and workmanship for a period of 36 months from the date of purchase provided the product is used for its proper purpose, in accordance with Mercator’s recommendations and within such voltage and current limits as are specified by Mercator in relation to the product.
