Specifications

ManualsBrandsMenvier Security ManualsHome building and DecorTS700

TS790 & TS900

10 - 56 Zone Intruder Alarm

Control Panels

Installation & Programming

Manual

ENT

ESC

A B

OMIT AREA

POWER

BUSY

ENT

ESC

A B

OMIT AREA

Engineers menu 1

Select Option :-

ENT

ESC

A B

OMIT AREA

POWER

BUSY

ENT

ESC

A B

OMIT AREA

POWER

FUNCTION

Summary of content (68 pages)

PAGE 1
TS790 & TS900 10 - 56 Zone Intruder Alarm Control Panels POWER BUSY Engineers menu 1 Select Option :- 1 2 3 1 2 3 4 5 6 4 5 6 7 8 9 7 8 9 ENT 0 ESC ENT 0 ESC B C A B C A OMIT AREA OMIT AREA POWER BUSY POWER FUNCTION 1 2 3 1 2 3 4 5 6 4 5 6 7 8 9 7 8 9 ENT 0 ESC ENT 0 ESC B C A B C A OMIT AREA OMIT AREA Installation & Programming Manual
PAGE 2
PAGE 3
Contents Overview Introduction . . . . . . . . . . . . . . . . . . . . . . . . . System Architecture . . . . . . . . . . . . . . . . . . . Control Panel . . . . . . . . . . . . . . . . . . . . . . . . Remote Keypads . . . . . . . . . . . . . . . . . . . . . 32 Character LCD (TS900.REM). . . . . . . . . 8 Character Starburst (TS790.STAR) . . . . . . 4 Character LED (TS700.REM) . . . . . . . . . . Remote Arming Station (TS700.ARM) . . . . TS900 NODE . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 4
Set System Date. . . . . . . . . . . . . . . . . . . . . . Change Passcode . . . . . . . . . . . . . . . . . . . Chime Circuits . . . . . . . . . . . . . . . . . . . . . . . Alter 24Hr Group . . . . . . . . . . . . . . . . . . . . . Print System Log . . . . . . . . . . . . . . . . . . . . . . Configure Wards . . . . . . . . . . . . . . . . . . . . . Log Event Codes . . . . . . . . . . . . . . . . . . . . . View System Log . . . . . . . . . . . . . . . . . . . . . Log Event Codes . . . . . . . . . . . . . .
PAGE 5
TS790 & TS900 Installation Manual Overview Overview Introduction Control Panel The TS790 and TS900 alarm control systems have been designed to suit medium to large installation sites. The TS900 system can be expanded from 10 to 56 zones, whereas the TS790 is expandable from 10 to 16 zones. Both systems feature “up” and “down” line loading, allowing the system to be remotely programmed or interrogated via the telephone line and a P.C.
PAGE 6
Overview TS790 & TS900 Installation Manual Remote Keypads TS700 LEC Up to 4 remote keypads can be connected to the control panel. Each remote keypad has two detection circuits and a single switched -ve output. There are four types of remote keypads that can be used: The Local Expansion Card (LEC) provides two programmable detection circuits and one programmable output. 32 Character LCD (TS900.
PAGE 7
TS790 & TS900 Installation Manual System Installation System Installation Cable Routing Node Network Wiring (TS900 Only) When installing cables, the following should be noted: Nodes require a 4 core cable for interconnection, and may be connected in a “daisy-chain” or “star” configuration. The distance between each Node must not exceed 100 metres. Power for detectors is provided by the Aux +/- terminals.
PAGE 8
System Installation TS790 & TS900 Installation Manual Remote Network Wiring Combined Network Wiring (TS900) Devices on the “Remote Network” require a 6 core c a b le fo r in te rc o n n e c tio n , a n d m ay be c o n n e c t e d i n a “ s t ar” o r “ da is y - c h a in ” configuration. The distance to the furthest device from the control panel must not exceed 100 metres. Power for detectors are provided by the A and B terminals (Figure 3).
PAGE 9
TS790 & TS900 Installation Manual System Installation Control Panel Installation Proceed as follows: 1. Open the control panel by removing two screws from the front cover. Remove the cover by sliding it up slightly to disengage the bottom clip, disconnect the earth bonding cable from the spade connection on the front cover, then lift clear. 2. Note the position of the cable entries as follows: (a) Plastic cable entries and 20mm knock-outs top and bottom for trunking.
PAGE 10
System Installation TS790 & TS900 Installation Manual Control Panel PCB Layout 1 AMP FS3 FACTORY RESET DIGI-MODEM JP6 T4 Z4 CIRCUIT 4 NOVRAMS AUX 12V T5 Z5 CIRCUIT 5 1 AMP BELL 12V BATTERY FAULT T6 Z6 CIRCUIT 6 T7 Z7 CIRCUIT 7 T8 Z8 CIRCUIT 8 Figure 6. 6 A B F G 6 U3 TS790 & TS900 Main PCB POWER ON V 2 3 4 5 U2 1 T3 Z3 CIRCUIT 3 Programmable Detection Circuits 1 - 8 SPEAKER VOLUME TRG STB TR- H/O H/O SPK AUX LINE +DC TAMP FLT POWER + + - T2 Z2 CIRCUIT 2 7 8 RR JP5 EARTH A. C.
PAGE 11
TS790 & TS900 Installation Manual Connection Terminals & Indicators The main PCB has the following “Jumper Plugs” (JP) and indicator LEDS: JP1 PRINTER This 6-pin plug is used for connecting to either a CPA6.P printer or a standard RS232 printer via the MPA printer adaptor. JP2 ENGINEERS REMOTE An Engineers remote keypad may be temporally connected to this 6-pin plug to allow programming and testing to be carried out at the control panel.
PAGE 12
System Installation TS790 & TS900 Installation Manual Mains Connection TS900 LCD Remote Keypad The mains supply is connected to a 3 way "Euro Type" fused terminal block, which is fitted with a 315mA fuse. All electrical connections should be carried out by a qualified electrician and must comply with the current IEE regulations. The TS900 remote keypad has a 32 character back-lit Liquid Crystal Display (LCD).
PAGE 13
TS790 & TS900 Installation Manual System Installation TS700 LED Remote Keypad Installation Procedure. The TS700 remote keypad has a 4 character LED display. + Always ensure that all power (mains and battery) is removed before making any connections to the remote keypad.
PAGE 14
System Installation TS790 & TS900 Installation Manual position the sounder responds as normal. When the link is set to the enabled position the sounder is only enabled when the remote keypad programmable output is active. For example, to make the keypad ward respective for ward A, program the output on the remote keypad to "Sounder Control A" (type 064) and set the "Ward Sounder Control" link to the enabled position. 7.
PAGE 15
TS790 & TS900 Installation Manual System Installation TS900 Node Layout Fit jumper-link to disable tamper switch Tamper switch JP2 FITTED = NO TAMPER NODE I/D ZD TD CIRCUIT D Programmable detection circuits A - D TE ZE CIRCUIT E ZC TC CIRCUIT C TF ZF CIRCUIT F ZB TB CIRCUIT B 1 2 3 4 5 TH ZH CIRCUIT H I/D selector TG ZG CIRCUIT G TA ZA CIRCUIT A JP2 AUX 12V 500mA + + From previous Node ABFG - - + Mains power indicator On = mains on Flashing = mains off Figure 13 Auxiliary 12V out
PAGE 16
System Installation TS790 & TS900 Installation Manual TS700 LEC Installation The TS700 LEC (Local Expansion Card) is connected to the “Remote Network” and provides two additional programmable detection circuits and a programmable output. The “Remote Network” may have up to three LECs connected, as the system will always require at least one remote keypad.
PAGE 17
TS790 & TS900 Installation Manual System Installation 500 meters or 100 Ohms 500 meters or 100 Ohms Alarm ZB Alarm ZB Tamper Tamper TB ZB ZA 4K7 Alarm Alarm Tamper Tamper 2K2 Max. 10 devices per circuit CIRCUIT A TA CIRCUIT B 4K7 Max. 10 devices per circuit TB Wiring N.O. devices (Exit Terminators) Figure 15 2K2 Tamper CIRCUIT B ZA TA CIRCUIT A TB Tamper 4K7 Alarm CIRCUIT B Alarm CIRCUIT A TA ZA 4K7 = Yellow, Violet, Red 2K2 = Red, Red, Red 2K2 Wiring N.O.
PAGE 18
System Installation TS790 & TS900 Installation Manual Auxiliary Tamper Typical External Sounder Control Panel 12V + 0V Tamper In H/O + H/O TR STB TRG - Figure 19 Tamper Out Strobe +ve Strobe -ve Trigger -ve These two terminals provide tamper protection to auxiliary devices such as power supplies, extension loudspeakers etc. If they are not used they must be linked out.
PAGE 19
TS790 & TS900 Installation Manual System Installation Digicom/RedCARE Installation Plug-on Digicom Installation A stand alone digital communicator, RedCARE STU or Paknet interface card can be connected to the control panel using the following connections: A plug-on digital communicator DC54 or DC58 may be fitted inside the control panel to allow alarm status information to be transferred to a dedicated central station.
PAGE 20
System Installation TS790 & TS900 Installation Manual Connecting a Printer TS790/900 Control Panel DC58M Alarm Receiving Centre Telephone Network The TS790/900 supports two type of printers, the CPA6 printer (no longer available) and any standard RS232 printer. When using a RS232 printer a DCI/MPA printer adaptor will be required. Menvier Security supply a DATAC printer kit which consists of a portable RS232 printer, charger unit and DCI/MPA adaptor. Using the CPA6 Printer 1.
PAGE 21
TS790 & TS900 Installation Manual System Installation Control Panel Outputs The control panel has four programmable outputs: R PAPER FEED POWE IN DATA Connect to JP1 PRINTER [1] Set of voltage free change-over contacts rated at 1 Amp. [-2] Switched -ve output rated at 500mA. [+3] Switched +ve output rated at 500mA. [+4] Switched +ve output rated at 500mA.
PAGE 22
System Installation TS790 & TS900 Installation Manual Installing a Monitored Power Supply Pre Power-Up Checks The TS790/TS900 can be configured to monitor the 519XB power supply unit using the 519FM fault monitor PCB. The 519FM plugs directly onto the 519XB PCB plug labelled JP1.
PAGE 23
TS790 & TS900 Installation Manual Power-Up Checks When the initial power-up checks have been completed, check the following: 1. Switch off the 240V mains supply and measure the DC voltage at each Node and remote keypad and ensure the voltage is greater than 11V whilst the system is powered from its standby battery. 2. Switch on the 240V mains supply and measure the DC voltage between the mains earth connection and AUX +12V. Then measure the DC voltage between the mains earth connection and AUX 0V.
PAGE 24
System Installation Section Circuits System Timers TS790 & TS900 Installation Manual Option Default Section Exit Terminator 02 Fire Signals All No Circuit 08 PA Audible 03 Silent 24hr Circuits No Circuit 09 Final Exit 04 Enable Duress Yes Circuit 10 PA Audible 05 Invert Abort No Circuit 11 - 56 Not Used 06 Set With Line Fault Yes 00 ACPO Delay 000 seconds 07 User Reset Yes 01 No of Re-arms 000 08 Constant Exit Tones Yes 02 Settle Time 007 seconds 09 Hi Security Engineer No
PAGE 25
TS900 Installation Manual Engineer's Menu 1 Engineer’s Menu 1 Introduction Engineers menu 1 is the first of three engineers menus, which is selected when the engineer’s passcode is entered. The engineer may leave “Engineer menu 1" by pressing the [ESC] key. The system will return to the unset condition but the remote keypads will show ”Engineer-on- site". This message will be cleared the next time a valid user passcode is entered or by exiting the engineer's mode via user menu 1.
PAGE 26
Engineer's Menu 1 TS900 Installation Manual Panel Outputs Digicom Channels Outputs 1 - 4 on the the control panel and remote keypad outputs 5 - 8 can be programmed to any of the output types shown on page 22 . The 8 plug-on digicom channels can be programmed to any of the output types shown on page 22. LCD Engineers menu 1 Select Options :- ENGR 1 - Engineers menu 1 Select Options :- E1 - PANEL - Digi Channel ? Enter Number > - PAN.- Type No. 004 004 Type No.
PAGE 27
TS900 Installation Manual No/Type Engineer's Menu 1 Description 006 P.A. Activates when a PA alarm is detected and deactivates when the alarm is reset. 007 Fire Activates when a Fire alarm is detected and deactivates when the alarm is reset. 008 System Set Activates when any ward is set and deactivates when the system is fully unset. 009 Activates for 10 seconds following entry Code Accepted of any valid passcode.
PAGE 28
Engineer's Menu 1 No/Type TS900 Installation Manual Description 040 Time Switch A This output is controlled by the settings of “Time Switch A” (see Engineers Menu 3) 041 Time Switch B This output is controlled by the settings of “Time Switch B” (see Engineers Menu 3) 042 Time Switch C This output is controlled by the settings of “Time Switch C” (see Engineers Menu 3) 043 Access Code Activates when an “Access” passcode is entered. The duration of this output is controlled by the setting of the “Acc.
PAGE 29
TS900 Installation Manual Engineer's Menu 1 Program Circuits 8 The TS790 can monitor up to 16 detection circuits, whereas the TS900 can monitor up to 56 detection circuits. Each circuit must be programmed in order for the system to respond correctly. Exit Terminator A circuit that is normally connected to a push button outside the protected premises, which can be used to finally set the system or area.
PAGE 30
Engineer's Menu 1 Circuit Attributes TS900 Installation Manual 6 Flagged Circuits with this attribute are monitored during the unset condition so that when they activate the circuit activation is stored. When the user decides to set the system, any circuits that have not been activated during the “Activity Dur” period are reported to the user, indicating that the detector may be obstructed. An example of this feature would be to assign movement detectors within a warehouse area with this attribute.
PAGE 31
TS900 Installation Manual Engineer's Menu 1 Starburst LED LCD Engineers menu 1 Select Options :- ENGR 1 - E1 - CCT NO.-- CT.-- 4 Program circuits Enter CCT No.>-Enter circuit No. e.g. 04 ENT Circuit No. Circuit Type CCT 04 NIGHT NIGHT NITE Enter circuit type: 0 = Not Used 1 = Night 2 = 24hr 3 = PA Silent 4 = PA Audible 5 = Fire 6 = Auxiliary 7 = Final Exit 8 = Exit Terminator 9 = Key Point A = PSU-Battery B = PSU-Fuse C = PSU-Power e.g. 7 for Final Exit ENT Attributes CCT 04 F.
PAGE 32
Engineer's Menu 1 07 Bell Delay This timer delays the activation of the external bell/sounder and internal sounders. This timer has a working range of 000-199 minutes. Note: Any alarm during the entry procedure will cancel the bell delay. 08 Double Knock Delay This is the “Double Knock” time window in which either two circuit activation must occur within this time to generate an alarm condition. Or the circuit must remain active for the whole duration of this time to generate an alarm condition.
PAGE 33
TS900 Installation Manual 18 Ward Menu Duration If the timer is set to 000 the “Code Set Group” passcodes function as normal, i.e., when the user enters their passcode the exit timer starts and the system attempts to set, on entering their passcode during entry, the wards assigned to their “Code Set Group” are unset. If the timer is set to anything other than zero all “Code Set Group” users are displayed a “Ward Selection Menu”.
PAGE 34
Engineer's Menu 1 TS900 Installation Manual LCD Engineers menu 1 Select Options :- Starburst LED ENGR 1 - LCD Engineers menu 1 Select Options :- E1 - 5 System Timers Enter Number >-- TIMER -- Setting Mode ? Enter Group > - Ti..-- System Timers Exit Time... 030 SET.MODE - S.BY - 0 = Full Set A = Part Set A B = Part Set B C = Part Set C 030 030 e.g. 0 for full set Enter new timer value e.g. 045 Set Mode System Timers Exit Time...
PAGE 35
TS900 Installation Manual Engineer's Menu 1 Remote Reset Algorithm When the system is programmed for “Engineer Reset” the requirement to send an engineer to site can be overridden by the user by using the “Remote Reset” facility. If an alarm is generated the system will respond with a four digit “seed” code which the user quotes to the Alarm Receiving Centre or alarm company. The “seed” code is then entered into a decoder and a unique “Remote Reset” code is generated.
PAGE 36
Engineer's Menu 1 10 O/M's Mimic Circuits When programmed as “Yes" the output modules mimic circuit activations. When programmed as ”No" output modules give circuit alarm indication. (Default = Yes) TS900 Installation Manual 18 Invert Output 1 When programmed as “Yes” panel output 1 is normal. When programmed as “No” panel output 1 is inverted.
PAGE 37
TS900 Installation Manual Engineer's Menu 1 Starburst LED LCD Engineers menu 1 Select Options :- ENGR 1 - E1 - 9 Configuration Enter Number >-- CONFIG.-- co.-- Enter configuration No. e.g. 07 for user reset Engineers menu 1 Select Option :- 0 User menu 1 Select Option :ESC 1 Sounder. ON > 08 Press ESC to end 2 Walk Test Press ESC to end Bell Test ENT Option No.
PAGE 38
Engineer's Menu 1 TS900 Installation Manual View Location Text (LCD Only) This option allows the engineer to view the panel location text. The text message is programmed in "Engineers menu 3", see page 44.
PAGE 39
TS900 Installation Manual Engineer's Menu 2 Engineer's Menu 2 Introduction Engineer's menu 2 is selected by pressing the [ENT] key whilst Engineer's menu 1 is selected. Each menu option can be selected by pressing the relevant "Hotkey".
PAGE 40
Engineer's Menu 2 TS900 Installation Manual View Circuits Set System Date Each detection circuit may be viewed to ascertain its status. The circuit status conditions and resistance are shown below: The system date is displayed in a day/date/month format on LCD remote keypads. it is also used to provide date stamps for events in the system log. Status Response Normal Min. Max. LCD Healthy Active Tamper Shorted None Alarm Tamper Alarm 2.2 KΩ 6.9 KΩ ∞ 0Ω 54 Ω 4.1 KΩ 54 KΩ 0Ω 4.
PAGE 41
TS900 Installation Manual Engineer's Menu 2 Chime Circuits Print System Log This option allows an alternative method of programming circuits as “chime”. The system log stores 700 events (1800 when expanded), if a printer is connected to the system it is possible to print a selected number of events. Once the print-out has been started it can only be stopped by selected this option again and entering "000" for the number of events.
PAGE 42
Engineer's Menu 2 TS900 Installation Manual Starburst LED LCD Engineers menu 2 Select Option :- ENGR 2 - E2 - ---01 CCT --01- 8 Configure Wards Enter CCT No.>-- View System Log The engineer can use this option to view the system log. The [A] and [C] keys allow you to scroll backwards and forwards through the log events. Engineers menu 2 Select Option :- Enter circuit No. e.g.
PAGE 43
TS900 Installation Manual Engineer's Menu 2 Log Event Codes LCD Starburst LED Description DATE CHANGED DATE CHG Dc System Date changed. DEFAULT CODE DEFLT 01 DF User passcode (01) reset to 5678 by the engineer. DURESS 01-31 DUR’SS 01-31 Du. 01-31 Duress alarm from user passcode (01-31). ENTRY 01-56 ENTRY 01-56 En. 01-56 Entry timer started by circuit (01-56). ENTRY ALARM 01-56 EN.ALM 01-56 EA. 01-56 Entry timed-out alarm from circuit (01-56). FACTORY RESTART FACT.
PAGE 44
Engineer's Menu 2 TS900 Installation Manual Log Event Codes LCD Starburst LED Description TAMPER 01-56 TAMP'R 01-56 TA. 01-56 Tamper alarm from circuit. TEST CCTS OFF TEST OFF To All circuits taken off “Test” TEST FAIL 01-56 T. FAIL 01-56 TF. 01-56 Circuit failed during “Test”. TIME CHANGED TIME CHG Tc System time changed UNSET WARD A/B/C/S UNSET A/B/C/S Un. ABCS Wards A, B, C or System Unset. WALK TEST WALK TST cT System “Walk Test” selected.
PAGE 45
TS790 & TS900 Installation Manual Engineers Menu 3 Engineers Menu 3 Introduction Engineers menu 3 is selected by pressing the [ENT] whilst Engineers menu 2 is selected. Each menu option can be selected by pressing the relevant “Hotkey”.
PAGE 46
Engineers Menu 3 TS790 & TS900 Installation Manual Time Switches The TS790/TS900 has three programmable time switches. Each time switch can be programmed with up to three separate on/off times and made to operate on any day of the week. The time switches can be assigned to outputs which in turn can be used to control internal or external lighting via a relay etc.
PAGE 47
TS790 & TS900 Installation Manual Engineers Menu 3 Part Set Groups Code Set Groups This option allows the engineer to define how the three part set buttons operate. Each group can be programmed so that it sets any combination of wards. For example "PART SET GROUP A" could be allocated wards A and C, whereas "PART SET GROUP B" could be allocated wards A and B. This option allows the engineer to define how the four code set groups operate.
PAGE 48
Engineers Menu 3 TS790 & TS900 Installation Manual Engineers Name (LCD Only) Circuit Text (LCD Only) This option allows the engineer to assign a name (7 characters) to user 00. When using the view log option you can press the [B] key to alternate between displaying the user number and user name. Each detection circuit can have up to 16 characters of text assigned to it.
PAGE 49
TS790 & TS900 Installation Manual Engineers Menu 3 Location Text Node Outputs This option allows the engineer to program a 32 character location message. When “Engineers menu 1" is selected the engineer can view this message. This can be used to provide the location details for the control panel, e.g., ”C P located in reception area", thus assisting service engineers unfamiliar with the site. This option allows the engineer to program the two outputs on each Node.
PAGE 50
Engineers Menu 3 TS790 & TS900 Installation Manual Voltage When this test option is selected the battery charging voltage at the control panel is displayed, the accuracy of this measurement is ± 0.2V. LCD Engineers menu 3 Select Option :- Starburst LED ENGR 3 - If the system is fitted with a plug-on digicom the top line of the display will show the status of the communicator. When you leave this test routine the digi channels and outputs are returned to their normal condition.
PAGE 51
TS790 & TS900 Installation Manual Engineers Menu 3 Custom Outputs A & B These options allows the engineer to program both custom outputs. The diagram below represent the logic circuit for the the custom output. + 1 When using the “Custom Output” for “AND” logic only, switches 1-4 must be programmed to the type “Always Off” and any of the unused “AND” switches must be programmed to the same type as one of the used switches.
PAGE 52
Engineers Menu 3 TS790 & TS900 Installation Manual Modem Options (LCD Only) LCD Only This option allows the engineer to access the following modem options: Engineers menu 3 Select Option :- C Call Back No.1 Modem options Select Option :- This option allows the first call back telephone number to be programmed. 4 Call Back No.2 Password This option allows the second call back telephone number to be programmed. Cursor |Modem Password Enter password. e.g. 5750 Call Back No.
PAGE 53
TS790 & TS900 Installation Manual Engineers Menu 3 Engineers menu 3 Select Option :- C Modem options Select Option :- 6 Digi programming Press ESC to end Telephone Nos 1, 2 & 3 TELEPHONE NO. 1 ENT Account Nos 1, 2 & 3 ACCOUNT NO. 1 Enter 4 digit account No. ENT Reporting Channels for Tel Nos 1, 2 & 3 REPORTS TO NO. 1 * * * * * * * * Use keys 1 - 8 to toggle channels 1 - 8. ENT Set/Day Channels SET/DAY CHANNELS * * * * * * * * Use keys 1 - 8 to toggle channels 1 - 8.
PAGE 54
Engineers Menu 3 TS790 & TS900 Installation Manual Reset Digicom When the system is powered up, the control panel logs-on the device that is connected to the digicom plug (JP3). If the device is changed or removed from the system you must either power the system down and back up again, or select this menu option in order for the device to be log-on again.
PAGE 55
TS790 & TS900 Installation Manual Appendices Appendices Point ID Extended Reporting Point ID extended reporting is a new format which when used with the DC58 or DC58M can be used to report circuit ID data, user ID etc. In order to used this format the DC58/DC58M must be plugged on t o t h e c o n t r o l p an e l a n d m u s t al so b e programmed to report “Extended Format” (refer to the instructions supplied with the DC58/DC58M).
PAGE 56
Appendices TS790 & TS900 Installation Manual P 7 C Kitchen 6 C Dining Room 5 3 C Hall Garage CP S Lounge 2 4 C RK 8 P C 1 Key: P P Passive Infra-Red Detector C Magnetic Contact S Smoke Detector RK Remote Keypad CP Control Panel 9 Bathroom Bedroom 2 P 10 Landing RK Bedroom 1 Bedroom 3 Figure 27 52 A Typical 3 Bedroom House
PAGE 57
TS790 & TS900 Installation Manual Appendices Domestic Part-Set Application Example The TS790/900 is very flexible in the way that the system can be part-set. The system may be part-set by using the part-set buttons on the remote keypad or by using a part-set passcode. The first application example shows how to use the part-set buttons to set different areas of a 3 bedroom house. The second example will show how to achieve the same results using a different approach.
PAGE 58
Appendices TS790 & TS900 Installation Manual Defining Part-Set buttons to Arm a Ward(s) This method of defining the part set groups requires you to think of the system in terms of separate areas of protection (Wards), then configuring the part set groups so that different combinations of wards are set. 1. From the previous part-set requirements assign the different physical areas to wards, e.g.: Ward A: Downstairs perimeter detection (Circuits 01,04, 05 & 06).
PAGE 59
TS790 & TS900 Installation Manual Appendices P 5 12 CP P P RK Stores C C 11 C 13 10 Workshop P Canteen 7 C C 6 9 8 P C Sales Office RK 4 3 P P 2 1 C RK P 14 C Key: P Passive Infra-Red Detector C P Magnetic Contact RK Remote Keypad CP 16 Control Panel 15 C RK Service Department Figure 28 Commercial premises 55
PAGE 60
Appendices TS790 & TS900 Installation Manual Commercial Part-Set Application This application example shows how to use the "Code Set Groups" to set and unset different areas within a commercial premises. Using the drawing of the building the following is required: + l The Sales Manager requires independent access to the Sales department and the Canteen. l The Workshop Manager requires independent access to the Workshop area and the Canteen.
PAGE 61
TS790 & TS900 Installation Manual 1. Program the Detection Circuit as a “Key Point” and set the attributes as “F * * * |* A * *”. The “F” attribute indicates that the “Full Set Group” is selected when the keyswitch is switched from “Healthy” to “Active”. The “A” attribute indicates that “Code Set Group A” is selected when the keyswitch is switched from “Healthy” to “Shorted”. 2. Program the code set groups so that the correct combination of wards are set and unset.
PAGE 62
Appendices TS790 & TS900 Installation Manual Text Editing Keys TS790/TS900 +DC POWER 0V Alarm (005) - 3 Abort (071) - 7 Second Alarm (011) - 8 Digicom When programming any text the keys on the keypad function as shown below: (stand-alone) +12V 0V 3 - Alarm 7 - Abort 8 - Confirmation 1 A 2 E 3 I 3 O 5 U 4 0 (zero) 7 Move cursor left 8 Change case ENT Accept text 9 Move cursor right 0 Space ESC Abandon text editing A Up the alphabet B Change cursor C Down the alphabet Figure 31 Alarm Abort
PAGE 63
TS790 & TS900 Installation Manual Setup New Users The TS790/TS900 allows up to 31 users to operate the alarm system, each user is assigned a user type, passcode and ward access. User 001 is the master user which has a default setting of 5678. User Types The following user types are available: Master User 02-31 can be programmed as the type "Master". If the installation company has programmed the master user for full access, he or she will have access to all user menus and options.
PAGE 64
Appendices TS790 & TS900 Installation Manual Code Set Group B Users 02-31 can be programmed as "Code Set Group B". This user type only allows the wards assigned by the installation company or master user to be set and unset. This user type does not have access to any user menus. Code Set Group C Users 02-31 can be programmed as "Code Set Group C". This user type only allows the wards assigned by the installation company or master user to be set and unset.
PAGE 65
TS790 & TS900 Installation Manual Appendices Notes 61
PAGE 66
Appendices TS790 & TS900 Installation Manual Engineers Menus Engineer's Menu 1 Engineer's Menu 2 Engineer's Menu 3 1 Panel Outputs 1 View Circuits 1 Time Switches 2 Digicom Outputs 2 Set Clock 2 Part Set Groups 3 Digicom Channels 3 Set Date 3 Code Set Groups 4 Program Circuits 4 Change Passcode (Engr) 4 Engineer's Name 5 System Timers 5 Alter Chime Circuits 5 Part Set Text 6 Setting Modes 6 Alter 24Hr Group 6 Circuit Text 7 System Print Out 7 Print System Log 7
PAGE 67
TS790 & TS900 Installation Manual No. 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 Output Type Bell On Strobe On Switch 12V Detector Reset Walk Test Alarm P.A.
PAGE 68
MENVIER Menvier Security Ltd. Kenn Road, Clevedon, Bristol BS21 6LH Tel: 01275 870078; Fax: 01275 343453 SECURITY 18796 Drg No. 33:1429:00 Issue 04 Doc.