NAND Flash-based Solid State Drive Standard Type GT series Product Specification Version 1.0 Oct. 2008 INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO MEMORIGHT PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN MEMORIGHT PRODUCTS OR TECHNOLOGY.
Revision History Revision No 0.0 0.1 1.0 History Draft Date Remark Initial issue Performance data updated Performance update Mar. 14,2008 Sept. 9, 2008 Oct. 20, 2008 Preliminary Preliminary Formal The attached data sheets are prepared and approved by MemoRight. And MemoRight has the right to change all the specifications in data sheets. MemoRight will evaluate and reply to any dear customer‘s requests and questions on the parameters of this device.
MemoRight NAND Flash-based Solid State Drive Contents 1. GENERAL DESCRIPTION ........................................................................................................................ 7 1.1 DENSITY ................................................................................................................................................. 7 1.2 FORM FACTOR .......................................................................................................................................
MemoRight NAND Flash-based Solid State Drive 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.2.8 5.2.9 5.2.10 5.2.11 5.2.12 5.2.13 5.2.14 5.2.15 5.2.16 5.2.17 5.2.18 5.2.19 5.2.20 5.2.21 5.2.22 5.2.23 5.2.24 5.2.25 5.2.26 5.2.27 5.2.28 5.2.29 5.2.30 5.2.31 5.2.32 5.2.33 6 Read Sector(s) (20h)................................................................................................................ 21 Read Sector(s) EXT (24h) .......................................................................................
MemoRight NAND Flash-based Solid State Drive List of Tables Table 1．Specification Summary Table 2．Products capacity Table 3．Default logic geometry Table 4．Physical organization Table 5．Recording and interface technology Table 6．Physical characteristics Table 7．Access time Table 8．Performance characteristics Table 9．Start/stop time Table 10．Write endurance Table 11．Power Consumption Table 12．Ambient temperature Table 13．SATA Connector Signal Definitions Table 14．SATA Connector Power segment Definitions Table
MemoRight NAND Flash-based Solid State Drive List of Figures Figure 1．NSSD Functional Block Diagram Figure 2．Physical specifications Figure 3．Memoright SATA Connector View Figure 4．Ordering Information MemoRight Confidential Page 6 3/6/2009
MemoRight NAND Flash-based Solid State Drive 1. General Description The NSSD (NAND Flash-based Solid State Drives) of MemoRight consists of semiconductor devices completely, and the storage media is NAND Flash which has high reliability and high compatibility. As the NSSD doesn't have any mechanical part such as platter (disk), motor and suspension, it gives a good solution in a UMPC and Tablet PC for a storage device with high performance and low power consumption and small form factor.
MemoRight NAND Flash-based Solid State Drive 1.5.6 Data Retention Data retention :>10 years Test under room temperature. 1.6 Power consumption Input voltage: +5VDC, ±5%(4.75V ~ 5.25V) Continue write : Typical 400mA Continue read : Typical 400mA Idle : Typical 200mA Standby : Typical 200mA Test under room temperature @ 5V 1.7 Environmental 1.7.1 Temperature Operating : 0'C ~ 70'C(Commercial) Non-Operation: -40'C ~ 85'C 1.7.
MemoRight NAND Flash-based Solid State Drive 2 Physical specifications Figure 2．Physical specifications MemoRight Confidential Page 9 3/6/2009
MemoRight NAND Flash-based Solid State Drive 3 Drive Specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases of the drives used throughout this manual are indicated the following drive models: MR25.2-032S MR25.2-064S MR25.2-128S 3.1 Specification Summary table The specifications listed in the table below are for quick reference.
MemoRight NAND Flash-based Solid State Drive (°C per hour max, non-condensing) 30°C (non-operating) Humidity (non-condensing) 50%,95% (operating) Relative humidity gradient Drive acoustics, sound power (dB) Non-recoverable read errors 30% per hour max Mean Time Before Failure (MTBF) 0 < 1 per 1014 bits read More than 1,100,000 hours ( 32GB typical ) Calculation model: Telcordia SR-332 Issue 1 Method 1, Case 1 Altitude 0-80000(Ft) / 0-24(km.
MemoRight NAND Flash-based Solid State Drive 3.5 Recording and interface technology Table 5: Recording and interface 3.6 Technology Specification Interface Serial ATA 1.0a Interface data transfer rate (Mbytes/sec max) 150(SATA 1.0a) Recording media Single Layer Cell(SLC) NAND flash Cache buffer 32 Mbytes Physical characteristics Table 6: Physical characteristics (mm) Height (inches) (mm) Width (inches) (mm) Length (inches) (grams) Typical weigtht (pounds) 3.7 0 9.5 -0.1 0 0.374 -0.004 0 69.
MemoRight NAND Flash-based Solid State Drive *Assumes that no error and no sector is relocated. * *Assumes that system ability supports the UDMA-6. 3.8 Performance characteristics The performance test results are based on environments as below: Mother Board: CPU: Chipset: Graphic: RAM: BIOS: OS: Test software: SSD: GIGBYTE X38-DQ6 E8400 3.00GHz Intel X38 + ICH9R NVIDIA6200LE Kingston 2GB DUAL channel DDR2-800 Award/6.00PG/F7 Windows XP pro sp2 IOMeter 2006.07.27 MR25.2-032S (FW: B8J22D1F) /MR25.
MemoRight NAND Flash-based Solid State Drive 8 KBytes 64KBytes 128 KBytes 0.5KBytes 4 KBytes 8 KBytes 64KBytes 128 KBytes 0.5KBytes 4 KBytes 8 KBytes 64KBytes 128 KBytes 0.5KBytes 4 KBytes 8 KBytes 64KBytes 128 KBytes Consecutive write(typical) Random read(typical) Random write(typical) 3.9 45.97 97.19 101.34 8.42 52.09 75.35 104.04 104.01 4.72 20.80 33.10 83.73 93.40 0.30 1.33 1.78 9.77 17.
MemoRight NAND Flash-based Solid State Drive write(100% cache miss) 16 KBytes 128 KBytes >3.2 >25 >2×108 >2×108 In actual application environments, since this drive have a 32MByte cache and the cache strategy fine tuned for NAND flash, the write endurance will exceed this specification in almost all situation. 3.11 Power specifications The drive receives DC power (+5V) through the interface connector. 3.11.1 Power consumption Power requirement for the drive is listed in the table.
MemoRight NAND Flash-based Solid State Drive 3.11.3 Voltage tolerance Voltage tolerance (including noise): 5V ± 5% 3.12 Environmental specifications 3.12.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drives usual temperature should not exceed 70°C (158°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is decreased linearly by 1°C every 1000 feet.
MemoRight NAND Flash-based Solid State Drive 4 Configuring and mounting the drive This section contains the specifications and the instructions for configuring and mounting the drive. 4.1 Static discharge and handling precautions After unpacking and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
MemoRight NAND Flash-based Solid State Drive z Power on your host and then format the SSD or initiate the SSD through the RAID card with the standard drive format procedure. z Please install the windows XP first then Vista if coexisted systems required.
MemoRight NAND Flash-based Solid State Drive 5 SATA interface The drive uses the industry-standard Serial ATA interface that supports 16-bit data transfers. It supports programmed input/output (PIO) modes 0–4; Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.
MemoRight NAND Flash-based Solid State Drive 15-pin segment. Table 14:SATA Connector Power segment Definitions Pin P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 Signal Name V3.3 V3.3 V3.3 Ground Ground Ground V5 V5 V5 Ground Reserved Ground V12 V12 V12 Signal Definitions 3.3V Power(Not used) 3.3V Power(Not used) 3.
MemoRight NAND Flash-based Solid State Drive E6h E0h 95h, E1h E2h 97h, E3h ATA 48bit address commands 24h Read Sector(s) EXT 25h Read DMA EXT 29h Read Multiple EXT 34h Write Sector(s) EXT 35h Write DMA EXT 39h Write Multiple EXT 42h Read Verify Sector(s) EXT EAh Flush CACHE EXT Sleep Standby Immediate Idle Immediate Standby Idle 5.2.1 Recalibrate (10h) When this command is issued, the NSSD sets BSY and waits for that the device is initialized, and then clears BSY. 5.2.
MemoRight NAND Flash-based Solid State Drive This command will verify one or more sectors by transferring data from the flash media to the data buffer and verifying the ECC is correct. The command is identical to the Read Sector(s) - 20h command except that DRQ is never set and no data is transferred to the host. 5.2.
MemoRight NAND Flash-based Solid State Drive This command is similar to Standby immediate. 5.2.24 Idle (E3h) This command is similar to Idle immediate. 5.2.25 Read Buffer (E4h) This command enables the NSSD to transfer the buffer data in cache. 5.2.26 Check Power (E5h or 98h) This command enables the Host to check the NSSD power mode. 5.2.27 Sleep (E6h) This command enables the Host set NSSD into sleep mode. 5.2.
MemoRight NAND Flash-based Solid State Drive 21 22 23-26 27-46 47 48 49 50 51 52 53 54 55 56 57-58 59 60-61 62 63 64 65 66 67 68 69-74 75 76-79 80-81 82 83 Retired Obsolete Firmware revision: 8ASCII characters Drive model number: 40 ASCII characters (Bits 7–0) Maximum sectors per interrupt on Read multiple and Write multiple (1) Reserved Standard Standby timer, IORDY supported and may be disabled Capabilities Retired Retired Words 54–58, 64–70 and 88 are valid Number of current logical cylinders Number o
MemoRight NAND Flash-based Solid State Drive 84 85 86 11 0 = Device Configuration Overlay feature set not supported 10 1/0 = 48-Bit Address feature set supported /not supported 09 0 = Automatic Acoustic Management feature set not supported 08 0 = SET MAX security extension not supported 07 0 = See Address Offset Reserved Area Boot, INCITS TR27:2001 06 0 = SET FEATURES subcommand not required to spin-up after power-up 05 1 = Power-Up in Standby feature set supported 04 0 = Obsolete 03 1 = Advanced Power
MemoRight NAND Flash-based Solid State Drive 87 88 89 90 91 92 93 94-99 100-103 104-126 127 128 129-159 160 161-175 176-205 206-254 255 5.2.
MemoRight NAND Flash-based Solid State Drive Table 17: Set features description Value 01h 02h 03h 04h 05h 06h 07h 09h 0Ah 10h 20h 21h 31h 33h 42h 43h 44h 54h 55h 5Dh 5Eh 66h 77h 81h 82h 84h 85h 86h 88h 89h 8Ah 90h 95h 99h 9Ah AAh ABh BBh C2h CCh DDh DEh E0h F0-FFh Description Reserved Enable write cache Set transfer mode based on value in Sector Count register Obsolete Enable advanced power management Enable Power-Up In Standby feature set.
MemoRight NAND Flash-based Solid State Drive 6 Compatibility summary 6.1 Tested Hardware platform versions The following list indicates the information of platforms which MemoRight tested during the compatibility testing process. The information contains board vendor, chipset/South Bridge and BIOS. The testing process is divided into desktop platform and Notebook platform. At the same time the compatibility testing process is also tested on RAID platforms.
MemoRight NAND Flash-based Solid State Drive 6.1.2 Notebook platform Table 19: Tested Notebook platform Mother Board versions Chipset/ South Bridge Board Vendor Dell INSPIRON 9300 BIOS Remark Intel i915PM/ ICH6-M ATI RS482/RS485M/ SB600 nForce7150M-630 M Phoenix A05 Compatible Phoenix 2.4.1 Compatible Phoenix F.06 Compatible Mac Book A1181 Intel965@ICH8-DO Insyde/MB31.88Z.0 08E.0711151547 Compatible SONY NR12H Intel 960/ ICH8-D0 Phoenix R0130J9 Compatible Dell VOSTRO 1000 Hp V3625AU 6.
MemoRight NAND Flash-based Solid State Drive ROHS MemoRight Confidential Page 30 3/6/2009
MemoRight NAND Flash-based Solid State Drive MemoRight Confidential Page 31 3/6/2009
MemoRight NAND Flash-based Solid State Drive FCC MemoRight Confidential Page 32 3/6/2009
MemoRight NAND Flash-based Solid State Drive CE MemoRight Confidential Page 33 3/6/2009
MemoRight NAND Flash-based Solid State Drive MTBF MemoRight Confidential Page 34 3/6/2009
MemoRight NAND Flash-based Solid State Drive MemoRight Confidential Page 35 3/6/2009
MemoRight NAND Flash-based Solid State Drive 8 Ordering Information MemoRight SSD Product Model Name: Example: MR25.2-032S M R 2 1 5 2 · 2 - 3 0 3 4 2 S 5 Figure 3.Ordering Information 1: MR: stand for MemoRight 2: Mechanical dimension 35: 3.5 inch 25: 2.5 inch 18: 1.
MemoRight NAND Flash-based Solid State Drive 9 MemoRight support services Product Quality Assurance It is guaranteed that the products are produced strictly in accordance with IS09001 standard. All selling products have been measured using specific testing systems. The quality, specification and performance of the products shall be in the same as the specification.
