Specifications

TEK PARTNER™ PLUS
UNIVERSAL REMOTE CONTROL
USER MANUAL
Congratulations!
Your TEK PARTNER™ Universal Remote Control is a state-of-the-art device which integrates many
different infrared remote controls. (NOTE: Th e TEK PARTNER™ is not compatible with UHF (RF)
controlled devices.)
The TEK PARTNER™ is pre -programmed at the fa ctory, but you will need to enter a Device Code for
each de vice to complete the program. Simply enter c orrect de vice codes for yo ur equipment and
your TEK PARTNER™ is ready to use! A Device Code List is included in this User’s Manual.
The TEK PARTNER™ replaces up to 4 separate remote controls to operate your infrared controlled
television (TV), video cassette recorder (VCR), cable box (CBL), and satellite receiver (SAT).
The TEK PARTNER™ has the following features:
TV, VCR, CABLE, and SA TELLITE MODES. Simply press t he desired DEVICE MODE button (TV, VCR
CBL, or S AT) once to select the operation MODE.
ID ENTRY. The ability to easily select the TV/VCR/CBL/SAT devices you wish to control.
ID RECALL. The ability to display the ID of the currently selected
TV/VCR/CBL/SAT device on the status indicator light.
POWER SCAN. The ability to search through the TV/VCR/CBL/SAT codes for a code that operates th
e
TV/VCR/CBL/SAT device.
POWER SCAN MODEL CHECK. Expands the ab ility of regul ar P ower Scan by allowing th e u ser to
remain in scan mode and test any valid button for the TV/VCR/CBL/SAT device being scanned.
MASTER POWER. The ability to turn on/off all TV/VCR/CBL/SAT devices at the same time upon pres
s
and relea se of the POWER button. This feature is user progra mmable to be enabled or disabled.
VOLUME PUNCH –THROUGH. In CBL or SAT MODE allows the volume to be controlled by either the
TV or the CBL or SAT. This feature is a user programmable selection.
COUCH MODE™. A feature that turns off the remote if a key is pressed for longer than approx. 3
minutes, like when the remote is stuck in the couch. This conserves battery power until the key is
released. This feature is not user programmable.
Page 1 of 10Hytek Manufacturing
3/10/03htt
p
://www.h
y
tekmf
g
.com/manual2.html
TABLE OF CONTENTS
INSTALLING THE BATTERIES
BUTTON FUNCTION
-TV/VCR MOD E
-CBL/SAT MODE
SETTING UP YOUR TEK PARTNER
-USING DEVICE CODES
-USING POWER SCAN (SEARCHING)
-USING ID REC AL L
-SETTING PUNCH-THROUGH
-ENABLING MASTER POWER
OPERATING THE TEK PARTNER
CARE & MAINTENANCE
TROUBLESHOOTING
SPECIFICATIONS
DEVICE CODE LISTS
-TV
-VCR
-CABLE
-SATELLITE
INSTALLING THE BATTERIES
Your TEK PARTNER™ requires 4 fresh AA-size batteries (alkaline batteries recommended).
1. Remove the battery cover on the back of your TEK PARTNER™.
2. Observe the polarity of the batteries and the "+/-" marks inside th e battery compartment.
3. I nsert the batteries.
4. Push the battery cover back in place.
NOTE: When all batteries are disconnected, the TE K PARTN ER™ retains its setting for a few hours.
Should you fail to replac e the batteries in time, you may have to re-program your TEK PARTNER™.
See SETTING UP YOUR TEK PARTNER™ section.
BUTTON FUNCTION
(TV/VCR MODE)
BUTTON FUNCTION
PWR POWER OFF/ON
VOL+/- VOLUME +/-
CH+/- CHANNEL +/-
MUTE SOUND OFF/ON
PREV CH LAST CHANNEL/RECALL
ENTER ENTER SELECTION
PLAY PLAY TAPE (VCR)
STOP STOP TAPE (VCR)
PAUSE PAUSETAPE(VCR)
REW REWIND
FF FAST FORWARD
REC RECORD
TV/VCR SW ITCH BETWEEN TV AND VCR (OR TV AND VIDEO) MODES
TV TV MOD E
VCR VCR MODE
0–90-9
BUTTON FUNCTION
(CBL/SAT MODE)
Page 2 of 10Hytek Manufacturing
3/10/03htt
p
://www.h
y
tekmf
g
.com/manual2.html