Specifications

38 39
2. Insertion of AA/HR6 or AAA/HR03 batteries
a) Insert 1 to 4 pcs AA/HR6 or AAA/HR03 NiMH batteries in the
compartments.
b) Respect the polarities (+) and (-) of the batteries and the
compartments.
3. Quick start : default mode ‘CHARGE at 200mA’
V
I. i2
CHARG E
200
CHARG E
mA
Page 4
mA
200
I00
I00
200
CHARG E
TEST
DISCHARGE
REFRESH
CHARG E
mA mA mA
DISCHARGE
Page 5
000
CHARG E
mA
I000
I.39
2.30
CHARG E
mA
2:35
CHARG E CHARG E CHARG E
h
V
Ah
CHARG E
f
060
I.4 i
2.40
CHARG E
mA
2:55
CHARG E CHARG E CHARG E
h
V
Ah
Page 6
I000
I.39
2.30
CHARG E
mA
2:35
CHARG E CHARG E CHARG E
h
V
Ah
CHARG E
f
060
I.4 i
2.40
CHARG E
mA
2:55
CHARG E CHARG E CHARG E
h
V
Ah
500
I.30
i920
mA
i:55
h
V
mAh
DISCHARGE DISCHARGEDISCHARGE DISCHARGE
500
I.30
i920
mA
i:55
h
V
mAh
DISCHARGE DISCHARGEDISCHARGE DISCHARGE
Page 7
I000
I.39
mA
2:35
h
V
mAh
CHARG E
f
060
I.4 i
2.05
mA
3:45
h
V
Ah
i000
I.23
i920
mA
0: i5
h
V
mAh
500
I.30
mA
i:30
h
V
mAh
DISCHARGE
TEST
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARG E
TEST
CHARG E
TEST
CHARG E
TEST
CHARG E
TEST
DISCHARGE
TEST
DISCHARGE
TEST
DISCHARGE
TEST
Page 8
I000
I.30
mA
0:05
h
V
mAh
060
I.4 i
i920
mA
2:35
h
V
mAh
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARGE
REFRESH
CHARG E
TEST
CHARG E
TEST
CHARG E
TEST
CHARG E
TEST
I920
a) Once the transformer has been plugged into
the power source and the battery has been
correctly inserted, the display will show the
battery voltage (ex. 1.12V) for 4 seconds.
Then “200mA Charge” (default mode) is
shown for another 4 sec.
b) The LCD screen will blink once to indicate the end of the setting and
the start of the charging process at a default rate of 200mA.
c) To modify the charging current (CURRENT key) or the charging mode
(MODE key), please read point 4 below.
d) The “FULL” sign is shown when the battery is fully charged. Read
more under point 8 (FULL – automatic cutoff).
4. CHARGE – selection of the charging current (CURRENT key)
The charging time will vary based on the selected charging current.
Please refer to the Table with average charging time in this manual.
• To program one charging current for all the inserted batteries
- press the CURRENT key within 8 sec. after insertion of the bat-
teries and
- press CURRENT again to toggle between the rates 200, 500, 700
and 1000mA and release the key once the desired current shows
in the display
- after a few seconds the display blinks to confirm that charging will
start at the selected rate.
• To program a charging current just for one particular battery
- first press the corresponding battery compartment number key
1-2-3-4 shortly within 8 sec. after insertion of the cell into the
compartment
- press the CURRENT key as described above.