Service manual

ManualsBrandsMemorex ManualsLED TVMVDT2402

SERVICE MANUAL

MVDT2402

Design and specifications are subject to change without notice.

COLOR TELEVISION/VIDEO CASSETTE RECORDER/

DVD VIDEO PLAYER

ORIGINAL

MFR’S VERSION A

CLASS 1

LASER PRODUCT

Summary of content (90 pages)

PAGE 1
CLASS 1 LASER PRODUCT MVDT2402 SERVICE MANUAL COLOR TELEVISION/VIDEO CASSETTE RECORDER/ DVD VIDEO PLAYER ORIGINAL MFR’S VERSION A Design and specifications are subject to change without notice.
PAGE 2
IMPORTANT WARNING CAUTION: DVD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS PLAYER USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS INSTRUCTED. THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE PLAYER.
PAGE 3
SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual. 2. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing. 3.
PAGE 4
WHEN REPLACING DVD DECK [ When the removal of the DVD Deck ] Before removing Pick Up PCB and DVD PCB connector, make the short circuit on the position as shown Fig. 1 using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged. [ When the installation of the DVD Deck ] Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD PCB connector. Pick Up PCB Make the sort circuit using a soldering. Fig.
PAGE 5
DISC REMOVAL METHOD AT NO POWER SUPPLY 1. Remove the Back Cabinet and AV PCB/DVD Block. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.) 2. Rotate the Main Gear in the direction of the arrow by hand. (Refer to Fig. 1) 3. Draw the Tray. Main Gear Deck CD Fig. 1 PARENTAL CONTROL - RATING LEVEL 4 DIGIT PASSWORD CANCELLATION If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps below. 1. 2. 3. 4. 5. 6. Turn Unit ON.
PAGE 6
TABLE OF CONTENTS IMPORTANT WARNING ......................................................................................................... SERVICING NOTICES ON CHECKING .................................................................................. HOW TO ORDER PARTS ....................................................................................................... WHEN REPLACING DVD DECK...........................................................................................
PAGE 7
GENERAL SPECIFICATIONS G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH Video Head 24 inch / 600mmV Flat 101 degree + 0.45 G / 0.18 G NTSC 2 Speaker Front 1.8 x 3.9 Inch 8 ohm 1.5W + 1.5W 1.5W + 1.
PAGE 8
GENERAL SPECIFICATIONS DVD Hi-Fi Audio Signal G-6 Power Power Source Power Consumption Protector G-7 Regulation G-8 Temperature G-9 G-10 Operating Humidity On Screen Display (TV/VCR) Menu Menu System Setup Output Level(-20dBFs 0dBFs=2.
PAGE 9
GENERAL SPECIFICATIONS G-11 On Screen Display (DVD) Index Mute Hi-Fi Repeat Zero Return DEW Menu (DVD) Yes Yes Yes Yes Yes No Menu Type Language Menu Subtitle Audio Picture TV Screen Size(4:3) OSD Display On/Off JPEG Interval Select Files Sound DRC (Dynamic Range Control) dts Decode Output(5.
PAGE 10
GENERAL SPECIFICATIONS Auto Shut Off G-14 Remote Control Unit No Signal No Operation Timer Back-up (at Power Off Mode) Unit Glow in Dark Remocon Format Custom Code Power Source Voltage(D.C) UM size x pcs Total Keys Keys TV/VCR DVD Power 1 2 3 4 5 6 7 8 9 0 ChannelChannel+ VolumeVolume+ Display (Call) Sleep Audio Select Mute Index- / SkipIndex+ / Skip+ T-REC Rec/OTR Slow+ Play Stop Rew / SearchF.
PAGE 11
GENERAL SPECIFICATIONS TV Auto Shut off Function End Call Index Search SQPB CATV CM Skip(30sec x 6 Times) Comb Filter (2Lines) VM Circuit TV Monitor Program Extend Choke Coil Energy Star Protect of FBT Leak Circuit Zero Return Power On Memory Dirty Head V-chip USA V-chip CANADA V-chip Parental Lock (DVD Only) Auto Stop (Pause, and Resume Stop after 5min.
PAGE 12
GENERAL SPECIFICATIONS Indicator Terminals Front Rear G-18 G-19 Set Size Weight G-20 Carton REC/OTR (VCR) Play (DVD) Stop (DVD) Skip+ /Search+ (DVD) Skip- /Search- (DVD) Open/Close (DVD) Input Select Main Power SW Power REC/OTR T-REC TV/VCR DVD Video Input Audio Input Other Terminal Video Input Audio Input Video Output Audio Output Digital Audio Output VHF/UHF Antenna Input AC Inlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.
PAGE 13
DISASSEMBLY INSTRUCTIONS 1-3: TV/DVD/VCR BLOCK (Refer to Fig. 1-3) 1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS 1. Remove the 2 screws (1). 2. Disconnect the following connectors: (CP303, CP404 and CP1704). 3. Remove the TV/DVD/VCR Block in the direction of arrow. 1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 6 screws (1). 2. Remove the 2 screws (2). 3. Remove the Back Cabinet in the direction of arrow. (1) Front Cabinet (1) Front Cabinet (1) (1) (1) TV/DVD/VCR Block (1) Fig.
PAGE 14
DISASSEMBLY INSTRUCTIONS 1-5: VCR PCB (Refer to Fig. 1-5) 1-7: DVD PCB/DVD DECK (Refer to Fig. 1-7) 1. Remove the 6 screws (1). 2. Remove the screw (2). 3. Remove the AV Jack Shield. 4. Disconnect the following connectors: (CP001, CP602B, CP604, CP2201, CP8001 and CP8002). 5. Remove the VCR PCB in the direction of arrow. 1. Make the short circuit on the position as shown Fig. 1-7 using a soldering. If you remove the DVD Deck with no soldering, the Laser may be damaged. 2. Remove the 4 screws (1). 3.
PAGE 15
DISASSEMBLY INSTRUCTIONS 2. REMOVAL OF VCR DECK PARTS NOTE 2-1: TOP BRACKET (Refer to Fig. 2-1) 1. In case of the Locker R installation, check if the one position of Fig.2-3-B are correctly locked. 2. When you install the Cassette Side R, be sure to move the Locker R after installing. 1. Extend the 2 supports 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE 1. After the installation of the Top Bracket, bend the support 1 so that the Top Bracket is fixed.
PAGE 16
DISASSEMBLY INSTRUCTIONS 2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A) 2-7: TENSION ASS'Y (Refer to Fig. 2-7-B) 1. Remove the screw 1. 2. Remove the Loading Motor. 3. Remove the Worm. 1. Turn the Pinch Roller Cam clockwise so that the Tension Holder hook is set to the position of Fig. 2-7-A to move the Tension Arm Ass'y. 2. Remove the Tension Spring. 3. Unlock the 2 supports 1 and remove the Tension Band. 4. Unlock the support 2 and remove the Tension Arm Ass'y. 5.
PAGE 17
DISASSEMBLY INSTRUCTIONS 2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports 1 and remove the T Brake Band. Idler Gear Idler Arm Ass'y (B) S Reel T Brake Band (A) 1 Hook section 1 T Reel (A) T Brake Arm 1 T Brake Spring 1 Fig. 2-8-A Fig. 2-9-A NOTE NOTE 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig.
PAGE 18
DISASSEMBLY INSTRUCTIONS 2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/ P5 ARM ASS'Y (Refer to Fig. 2-10-A) 1. Unlock the support 1 and remove the Cassette Opener. 2. Remove the Pinch Roller Block and P5 Arm Ass'y. Cassette Opener 1 Spring Position Fig. 2-11-B 2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12) Pinch Roller Block 1. Remove the screw 1. 2. Remove the FE Head. P5 Arm Ass'y 1 Main Chassis FE Head Fig. 2-10-A NOTE 1. Do not touch the Pinch Roller. (Use gloves.) 2.
PAGE 19
DISASSEMBLY INSTRUCTIONS 2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14) NOTE 1. 2. 3. 4. 5. 1. In case of the Pinch Roller Cam and Main Cam installation, install them as the circled section of Fig. 215-B so that the each markers are met. (Refer to Fig. 2-15-B) Remove the Capstan Belt. Remove the screw 1. Remove the Capstan Holder. Remove the 3 screws 2. Remove the Capstan DD Unit. Pinch Roller Cam Marker Capstan Belt 1 Capstan Holder Capstan DD Unit Main Cam Fig.
PAGE 20
DISASSEMBLY INSTRUCTIONS 2-17: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/ CLUTCH GEAR (Refer to Fig. 2-17-A) 1. 2. 3. 4. Cassette Guide Post 1 Remove the Polyslider Washer 1. Remove the Clutch Ass'y and Ring Spring. Remove the Clutch Lever. Remove the Coupling Gear, Coupling Spring and Clutch Gear. Inclined Base S Unit Inclined Base T Unit P4 Cap 1 Clutch Ass'y Ring Spring Coupling Gear Clutch Lever LED Reflector Coupling Spring Clutch Gear • Screw Torque: 5 ± 0.5kgf•cm 2 Fig. 2-18-A NOTE 1.
PAGE 21
DISASSEMBLY INSTRUCTIONS 3. REMOVAL OF DVD DECK PARTS NOTE NOTE 1. In case of the Main Chassis Ass'y, install it from (1) to (4) in order. (Refer to Fig. 3-2-B) 2. In case of the Main Chassis Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-2-C. 1. Do not disassemble the DVD DECK PARTS except listed parts here. Minute adjustments are needed if the disassemble is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y.
PAGE 22
DISASSEMBLY INSTRUCTIONS NOTE 3-5: CLAMPER ASS'Y (Refer to Fig. 3-5-A) 1. In case of the Pulley Motor installation, check if the value of the Fig. 3-3-B is correct. 2. When installing the Loading Motor PCB Ass'y, install it correctly as Fig. 3-3-C. 3. In case of the Loading Motor PCB Ass'y installation, hook the wire on the Main Frame Ass'y as shown Fig. 3-3-C. 1. Press the Clamper and rotate the Clamper Plate clockwise, then unlock the 3 supports 1. 2.
PAGE 23
DISASSEMBLY INSTRUCTIONS Insulator (R) ~ FEED MOTOR ~ Main Chassis Ass'y (Top Side) BLUE (4) ORANGE (3) Switch PCB Ass'y Fig. 3-6-C ~ SPINDLE MOTOR ~ BLACK (2) 3-7: RACK FEED ASS'Y/SWITCH PCB ASS'Y/FEED MOTOR (Refer to Fig. 3-7-A) RED (1) • Install wire from (1) to (4) in order. 1. 2. 3. 4. 5. 6. 7. Remove the screw 1. Remove the Rack Feed Ass'y. Remove the screw 2. Remove the Switch PCB Ass'y. Remove the 2 screw 3. Remove the Feed Motor. Remove the Motor Gear. Fig.
PAGE 24
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to remove the other. 4. REMOVAL OF ANODE CAP Read the following NOTED items before starting work. NOTE * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged.
PAGE 25
DISASSEMBLY INSTRUCTIONS 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 5-3.) 5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL NOTE 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 5-1.
PAGE 26
DISASSEMBLY INSTRUCTIONS INSTALLATION 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 5-8.) 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 5-5.) Thin-tip Soldering Iron IC Soldering Iron Fig. 5-8 5.
PAGE 27
KEY TO ABBREVIATIONS A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASS’Y AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.
PAGE 28
KEY TO ABBREVIATIONS S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.
PAGE 29
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key simultaneously. The both pressing of set key and remote control key will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 5 seconds before Power On. Set Key Remocon Key Standard Time (seconds) VOL.
PAGE 30
PREVENTIVE CHECKS AND SERVICE INTERVALS The following standard table depends on environmental conditions and usage. Parts replacing time does not mean the life span for individual parts. Also, long term storage or misuse may cause transformation and aging of rubber parts. The following list means standard hours, so the checking hours depends on the conditions. Time Parts Name 500 hours 1,000 hours 1,500 hours 2,000 hours 2,500 hours Audio Control Head Notes Clean those parts in contact with the tape.
PAGE 31
PREVENTIVE CHECKS AND SERVICE INTERVALS 2. TAPE RUNNING SYSTEM CLEANING When cleaning the tape transport system, use the gauze moistened with isopropyl alcohol. NOTE After cleaning the heads with isopropyl alcohol, do not run a tape until the heads dry completely. If the heads are not completely dry and alcohol gets on the tape, damage may occur. 3. CYLINDER Wrap a piece of chamois around your finger. Dip it in isopropyl alcohol. Hold it to the cylinder head softly.
PAGE 32
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 5 seconds before Power On. • No need setting for the position of the mark @ due to the adjustment value.
PAGE 33
SERVICING FIXTURES AND TOOLS (For 2 heads model) VHS Alignment Tape JG001 (VN2S-LI63) JG001A (VN2S-CO13) JG001Q (VN2S-LI63H) JG001T (VN2S-X63) (For 4 heads model) VHS Alignment Tape JG001B (VN1S-LI63) JG001I (VN1S-CO13) JG001P (VN1S-LI63H) JG001S (VN1S-X63) JG002B Adapter JG002E Dial Torque Gauge (10~90gf•cm) JG002F (60~600gf•cm) JG005 Post Adjustment Screwdriver Part No.
PAGE 34
MECHANICAL ADJUSTMENTS 1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. CONFIRMATION AND ADJUSTMENT Read the following NOTES before starting work. • 1. Set to the PLAY mode. 2. Adjust the adjusting section for the Tension Arm position so that the Tension Arm top is within the standard line of Main Chassis. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.
PAGE 35
MECHANICAL ADJUSTMENTS 1-4: CONFIRMATION OF VSR TORQUE NOTE 1. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Picture Search (Rewind) mode. (Refer to Fig.1-4-B) 2. Then, confirm that it indicates 120~180gf•cm. If the torque is out of the range, replace the following parts.
PAGE 36
MECHANICAL ADJUSTMENTS 2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD 2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) When the Tape Running Mechanism does not work well, adjust the following items. 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5.
PAGE 37
MECHANICAL ADJUSTMENTS 3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE 4 5 6 3 2 7 1 10 9 1. Tension Connect 2. Tension Arm 3. Guide Roller 4. Audio/Control Head 5. X value adjustment driver hole 8 6. P4 Post 7. T Brake Spring 8. T Reel 9. S Reel 10.
PAGE 38
ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL ADJUSTMENTS Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION • Use an isolation transformer when performing any service on this chassis. • Before removing the anode cap, discharge electricity because it contains high voltage. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position.
PAGE 39
ELECTRICAL ADJUSTMENTS (TV SECTION) 2-7: HORIZONTAL SIZE 2-2: CONSTANT VOLTAGE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (29) on the remote control to select “H. SIZE”. 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes 10 ± 4%. 1. Set condition is AV MODE without signal. 2.
PAGE 40
ELECTRICAL ADJUSTMENTS 2-12: PARABOLA 2-17: BRIGHT CENTER 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (30) on the remote control to select “PARABOLA”. 4. Press the VOL. UP/DOWN button on the remote control until the right and left vertical lines are straight. 1. Activate the adjustment mode display of Fig.
PAGE 41
ELECTRICAL ADJUSTMENTS 2-19: COLOR CENTER 2-21: SUB CONTRAST MAX 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the oscilloscope to TP802. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (23) on the remote control to select "COL CENT". 5.
PAGE 42
ELECTRICAL ADJUSTMENTS 3-3: STATIC CONVERGENCE 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 1.
PAGE 43
ELECTRICAL ADJUSTMENTS 4.
PAGE 44
DVD BLOCK DIAGRAM HA0~HA20, HD0~HD15 DVD LOADER DM III A, B, C, D, E, F Pick up RF 64M SDRAM IC4005 HY57V641620 HGT-7 SDD0~SDD15 FLASH 8M IC4007 SST39VF800A70-4C-EK-D SDA0~SDA11 VCR BLOCK CD4002 RFA_SDEN, DATA, SCLK READ CHANNEL IC2601 ZR36708TQC CD, DVD, LD AAF_CE, FE, TE, PI TX RX FNN, FNP UNREG+3.8V VBIASS0, S1 P.CON+5V DEFECT, LINK, MIRR, LDON Loading Motor P.CON+9V MPEG/MICON/DSP IC4001 ZR36762PQCG_V REG+1.
PAGE 45
Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM X4501 3.579545MHz Q4507 50 39 PULL OUT DRIVER TIMMING L H.SW REC FM-EQ 66 CYL 3 EP/LP-CH1 (R) 65 4 SP-CH2 (L) 72 5 SP_COM 6 SP-CH1 (R) 7 HF2 (L) 8 HF_COM 9 HF1 (R) H H.AMP SW L R Main CONV P H FM DEM REC AMP 8 EQ AMP 6 Y/C_DATA 53 Y/C_CLK VCA 36 CLAMP 34 H. AMP_SW1 C. ROTARY C ROT 57 RF SW IN H. SW VCR_A_MUTE MICON R V-AGC ENV DET 59 P R Chara INS. ALC ENV. DET VIDEO OUT COMP 60 OUT 24 COMP DUMMY_V.
PAGE 46
MICON BLOCK DIAGRAM TV_POWER_H VCR_A_MUTE SYSCON/TIMER/SERVO IC IC101 OEC8076A VCR_POWER_H REGULATOR 92 VCR_POWER_ON-H Q114 POWER_FAIL TV Q116 AV_SW1 COMB FILTER 1 POWER FAIL BUFFER 7 AV_SW1 AV_SW AV_SW2 DVD IN/OUT X101 32.768KHz TX DVD RESET EXT_A_MUTE EXT_MUTE IN/OUT HIFI ENV 88 HIFI_H.SW ST_SELECT 15 RX OSC0 37 16 TX OSCI 38 41 X0 CVN2 50 VIDEO OUT Y/C VIDEO 40 XI DUMMY.V.SYNC 24 DUMMY_V.SYNC H.SW 23 H.SW X102 14.31818MHz C_ROTARY 98 C.
PAGE 47
IN/OUT BLOCK DIAGRAM Q4202 REW OPEN/CLOSE STOP/EJECT VOL DOWN PLAY MUTE SW MUTE SW REC/OTR STOP CH.DOWN PLAY SW_AUDIO_OUT_R 5 CH MUTE SW_AUDIO_OUT_L 3 SOUND AMP/ SURROUND 4 CH.
PAGE 48
CHROMA/IF BLOCK DIAGRAM CHROMA/IF_ IC IC601 LA76324NM-MPB-E Y/C/AUDIO/ HEAD AMP 36 60 V_SYNC OSD_R 57 OSD_G 56 OSD_B 55 OSD_Y 54 35 50 59 H.SYNC PROTECT AT+5.7V REG REGULATOR 10V_REG. IC602 KIA78L10F-RTF 6 51 Q602 5 V_SYNC SCL P.CON+5V X601 3.579545MHz MICON SDA MICON PROTECT 1 3 MOTOR+12V 11 8.5V REG 13 P.CON+8V 21 DIGITAL COMB FILTER SW_C 40 COMB FSC 32 Y/C_VIDEO_Y DVD IN/OUT 7 DVD_Y/C_Y 25 FROM TO TV CP603 16 CUT OFF 14 R.OUT 3 15 G.OUT 4 B.
PAGE 49
SOUND AMP/SURROUND BLOCK DIAGRAM SOUND AMP IC IC352 AN7522N 1 TV 5 9 6 8 2 12 4 10 SOUND +B SOUND_R+ SOUND_L+ IN/OUT SP_OUT_L SP_OUT_R SPEAKER SP351 SPEAKER SP352 TV_POWER_H TV_A_MUTE MICON SCL SDA 18 17 16 19 SURROUND-IC IC302 AN5891SA-E1V 31 REGULATOR P.
PAGE 50
Hi-Fi/DEMODULATOR BLOCK DIAGRAM HI-FI/AUDIO/H.AMP/DEM IC IC5501 AN3663FBP L/R MIX AGC HF1 22 REC LPF AMP VCO AUDIO_OUT_R 1 AUDIO_OUT_L 2 DVD_A_OUT_R 4 DVD_A_OUT_L DVD IN/OUT 3 INPUT SW HF2 HF_COM 24 AMP 21 OUTPUT SW 10 FRONT_A_IN_R 15 FRONT_A_IN_L 9 REAR_A_IN_R 14 REAR_A_IN_L AMP 53 AMP 57 IN/OUT Y/C/AUDIO/ HEAD AMP PNR VCO-FO ADJ LOGIC BPF 48 FSC 45 Y/C_AUDIO 62 NORMAL_A 61 FM LIM DBX NOISE REDUCTION DEM BLOCK 29 V. REC_ST-H 28 HIFI_ENV 27 HIFI_H.
PAGE 51
DIGITAL COMB FILTER BLOCK DIAGRAM P.CON+5V REGULATOR P.CON+12V 10 16 8 AT+30V COMB_FSC Q1502 P.
PAGE 52
DVD IN/OUT BLOCK DIAGRAM AV SW1 DVD_RESET CP8001 3 MICON TX TX RX 4 RX 6 P.CON+9V P.CON+9V_D 7 P.CON+D5V P.CON+5V_D 8 P.CON+3.3V P.CON+3.3V 9 P.CON+3.3V P.
PAGE 53
REGULATOR BLOCK DIAGRAM Q3003 AT+5V OUT AT+5V Q3014 BACKUP+5V BACKUP+5V DVD_H MICON AT+12V VCR_POWER_H P.CON+5V_A P.CON+5V_A OUT IC IC3003 KIA278R05PI P.CON+5V OUT IC IC3004 KIA278R05PI P.CON+5V_D OUT IC IC3001 KIA278R05PI P.CON+5V_C P.CON+9V_D OUT IC IC3002 KIA278R09PI P.CON+5V AT+5V 1 2 4 1 2 4 1 2 1 4 2 4 P.CON+8V Q3001 UNREG+8V TV BUFFER P.CON+5V_A MOTOR+12V UNREG+5V +B P.CON+12V Q3008, Q3009 Q3015 IN/OUT Hi-Fi/DEMODULATOR SW BUFFER P.
PAGE 54
TV BLOCK DIAGRAM MOTOR+12V Q1702 RELAY DRIVER 2 +B REGULATOR UNREG+8V 1 UNREG+5V DEGAUSS RELAY RY1701 3 DEGAUSS_H MICON 4 L1703 DEGAUSS COIL D1705, D1706, D1710, D1711 Q406 CURRENT DET AC IN TRANSFORMER SWITCHING T1701 F1701 18 FEED BACK SWITCHING IC1702 TL431AILP 3 2 3 1 14 6 10 7 11 Q1705, Q1706 SWITCHING VR1701 +B ADJ. 1 17 FEED BACK IC1701 PS2561AL1-1-V(W) SOUND AMP SOUND +B CP603 Q802, Q803 V.
PAGE 55
F-1 C4042 Q4004 CD4002 R8114 R8115 C8122 W824 Q8102 W826 C4065 C4072 R4064 C4018 R4008 C4014 C4019 C4020 C4004 C4013 C4010 W806 B4001 C4005 C4033 C4076 C4027 C4089 C4029 C4090 C4030 C4028 C4088 R4012 B4003 C4075 C2618 C2627 C2647 C2642 C2617 C2623 R2605 R2610 R2320 R2602 R2603 C2615 C2311 C2639 C2638 C2611 C2307 B2602 C2658 C2637 C2657 C2308 C2659 C2660 C2635 C2312 C2626 C2609 R2611 C2632 C2645 B2603 C2304 R2312_1 C2313 R2635 R2649 B2601 C2636 R232
PAGE 56
L001 J8007 C4206_1 R4209 C4220 C8094_1 L8002 C4205_1 R4220 C4211 C4212_1 R4239 C3009 J4201 W026 C3002_1 C3007 C3004_1 C3005 R3004 FH1702 F1701 CD1702 RY1701 FH1701 D3008 R1702 CP1704 L1701 C1727 C4558 CP1707 D1730 W092 D1731 W150 C4543 C4547 W251 C5542 D1711 C1710 C1708 D1735 D1724 D1706 D1736 D1721 W146 C5528 C5540_1 C5551 W148 W250 L5504 C5564 C5523 C5545_2 C5555_2 D1713 C5554 C5559 W891 C4550 X4501 W151 C4508 W153 W152 CP4501 W877 C1728 B1703_1
PAGE 57
R304 Q4204 Q1503 Q8007 Q8006 IC1501 R1501 IC1502 R101 R166 R1502 R165 Q606 R2208 C2205 R2206 R111 R152 C143 IC103 1 R2201 R8027 26 R139 76 Q2201 R2205 R8056 C8014 C2202 C8077 R8050 R8052 R8053 R2202 C5503 C5517 R5506 C5521 C5527 R5507 R5509 C107 W881 C2209 W863 R105 IC1504 C2213 C1535 C8012 C1709 C1532 C2207 W872 Q106 C2203 R8021 R8023 R8047 R8020 C136 C8090 C5522 R5504 C5511 R5523 C5506 C8079 R8048 R8026 C8025 C8081 C8064 C8070 R8054 R8049 W851 C151 C5504 R
PAGE 58
PRINTED CIRCUIT BOARDS DEFLECTION/CRT/OPERATION SOLDER SIDE HS401 Q403 W818 D415 0 W804 R414 SW2258 W017 B403 C408 R2257 C418_2 D405 C417_1 R412_1 C402_1 R819 W831 D804 Q805 FB401 CP603B W018 D805 W838 W833 C412 C816 CC801 W836 D806 C818 CP802B SW2257 R807 R817 C815 R818 C817 C819 W837 D406 L401 L402 W832 R2256 R810 Q803 R808 W834 R454 W805 SW2256 D801 L403 C449_1 Q807 R806 R2255 R805 R809 J8 6 01 R43 C403 R423 D419 W852 D408 R440 TP401 C426 W014 C429
PAGE 59
A B C D E F G H MPEG/MICON/DSP SCHEMATIC DIAGRAM (DVD PCB) 55 RAMADD(5) 103 RAMDAT(15) 56 RAMADD(2) 104 RAMDAT(0) 0.1 F C4076 R4045 4.7K R4018 4.7K C4035 16P CH R4016 HOME LDON R4019 R4020 R4021 R4069 DJTDO DJTDI DJTMS ICETCK ICETDO ICETDI SYS_MUTE 33 33 33 4.7K TP4006 ML TP4004 MC MD TP4005 TP4007 TP4008 I2CCLK R4024 4.7K C4031 0.
PAGE 60
A B C D E F G H MEMORY SCHEMATIC DIAGRAM (DVD PCB) 8 A19 DQ2 A18 15 1.2 34 HD2 0 DQ10 R4041 1.5 RAMCLK 3 HA19 R4048 3.3 1.6 2.6 RD DQ8 A6 DQ0 A5 DE# A4 16 17 18 19 HD0 A7 20 0.9 DQ1 21 HD8 32 1.4 A17 30 HD1 DQ9 29 1.4 28 HD9 31 47K 1.6 HA18 SD_A11 0.7 HA17 1.4 HA7 1.6 HA6 1.6 HA5 1.3 0 NC 0 SD_A9 0.2 SD_A8 0.2 SD_A7 1.0 SD_A6 1.0 SD_A5 1.0 SD_A4 0.
PAGE 61
A B C D E F G H RF AMP/DSP SCHEMATIC DIAGRAM (DVD PCB) 8 8 FNN FNP F B 12K +-1% F 0.1 47 KA 0.1 F C2645 6.3V 6.3V 47 KA C2644_1 0.1 F C2643_1 C2642 R2336 5.6K R2318 220P CH C2304 C2312 0.001 B 0.001 B C2309 220P CH C2305 TP45 10K R2334 TRAY_CLOSE TP2 1K 27K R2326 R2324 W864 R2319 27K 1.5K R2316 470 +-1% TRAY_OPEN 4 4.7K R2327 TP140 3.9K TP139 1M R2321 R2339 HS76 HS2301 763WSA0026 4.1 TP68 TP64 0 8.8 0.8 0.9 4.1 4.1 4.1 TP69 0 15 16 17 18 0 5.1 3.
PAGE 62
A B C D E F G H AUDIO/VIDEO SCHEMATIC DIAGRAM (DVD PCB) 8 8 470 R8109 470 470 470 R8119 R8108 470 470 R8120 R8107 R8118 P.CON+A5V DAC_C_VIDEO 10 DAC_B_VIDEO 7 7 9 FROM/TO MPEG/MICON/DSP DAC_D_DVD_VIDEO P.CON+A5V 1.4 VIDEO_BUFFER Q8102 KTA1504S_Y_RTK P.CON+5V RESET MC MD ML AMCLK ABCLK ALRCLK ASDATA0 C8106 L8102 150P CH C8104 150P CH DAC_VIDEO_D 1uH 0305 C8109 L8103 0 150P CH C8107 1.3 0.5 12P CH 150P CH 0 VIDEO_BUFFER Q8103 KTA1504S_Y_RTK C8108 DAC_VIDEO_B 8 0.
PAGE 63
A B C D E F G H Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM (VCR PCB) 69 CP4503 B2013H02-2P 1 FE HEAD(HOT) AUDIO PB SW Q4502 KTC3875S_Y_RTK 0 0.7 R4503 10K C4511 C4506_1 10K R4511 0 0.01 B R4519 4.7K HOT R4545 1K L4506 C4556 0.01 B 40 39 R4559 2.2K 1/4W 37 36 35 34 V.SYNC B W870 AUX_V[F/R] FROM DVD IN/OUT 0.22 KA C4576 DVD_VIDEO 50V C4564_1 R P 1 KA 4 10V 33 KA 26 V.SYNC SEP FROM/TO DIGITAL COMB FILTER 3.6 NC 0 Y/C_VIDEO R Y-VCC L4509_1 11 R4550 100uH P.
PAGE 64
A B C D E F MICON SCHEMATIC DIAGRAM G H (VCR PCB) BACKUP+5V 8 8 SDA VCC TEST SCL SDA VSS A2 A1 A0 EEP ROM IC IC199_1 AT24C04N-10SI-2.7 3 4 0 0 7 0 C154 0.001 B 0 4.8 4.7K AV_SW1 GND FROM/TO IN/OUT IIC_OFF KEY_A TV_A_MUTE T-REC_LED 4.8 W841 SCL W842 SDA REMOCON_IN EXT_A_MUTE VCR_A_MUTE 0 TX 0 RX EXT_MUTE TV_POWER_H 0 NC 5.0 0.1 OSD_G Y/C_CLK OSD_B OSD_Y 9 0 8 4.9 7 0 6 0.4 5 5.0 4 NC 2.4 2.4 0 5.0 TV_POWER_H EXT_A_MUTE 5.1 0 V.
PAGE 65
A B C D E F G H IN/OUT SCHEMATIC DIAGRAM (VCR PCB) 8 8 FROM CRT/OPERATION CP2201 (CD2251) A2001WV2-2P 2 GND 1 KEY-B KEY_B 7 220 CH H 2 E 1.5 68 6 2.2K 1.5K 5.1 R8013 R8003 D AUDIO DRIVER Q8002 2SC2412K 100K 1 3.3K R8006 22P LTL-1CHEE-002A R8004 F R8007 P.CON+5V 0.1 1.7 COAXIAL J8007 MSP-251V-05NI-FE-LF 270 1/4W R2223 TV_POWER_H AT+5V C8010 B8001 W4BRH3.5X6X1.
PAGE 66
A B C D E F G H CHROMA/IF SCHEMATIC DIAGRAM (VCR PCB) AT5.7VREG 8.5VREG COMB_FSC P.CON+5V_B 25 W893 P.CON+8V P.CON+5V P.CON+5V 8 (W101) FROM/TO REGULATOR1 SW_C P.CON+5V_C VCR_POWER_H 8 X601 100CT3R532 3.579545MHz 22K 0.1 B C625 6.3V 0.047 R626 B 220 KA C627 0.1 C621 C629 C630 4.7M B 34 8P CH 1B C626 680K R624 22K 8P CH C624 0.1 B C632 0.1 F C631 0.1 B 7 R625 R620 0.1 C646 B C644 0.
PAGE 67
A B C D E F G H SOUND AMP/SURROUND SCHEMATIC DIAGRAM (VCR PCB) 8 8 SOUND AMP IC IC352 AN7522N 2 3 4 3.5 0 5 3.5 6 7 3.9 8 1.3 9 0 HS351 763WAA0255 7 - R + 10 1.3 C328 6.6 L 11 6.6 3.5 12 0 R357 1K 7 C358 0.0056 B C331 C302 0.0056 B FROM/TO IN/OUT 16V 10 KANP W843 FROM TV POWER 3.5 50V 22 YK 1 - 16V 10 KANP C350 + SOUND_R+ SOUND_L+ R356 SOUND+B C321 25V SP_OUT_R SP_OUT_L 100K 1/4W 2200 YK SOUND_GND R301 6 5.
PAGE 68
A B C D E F G H Hi-Fi/DEMODULATOR SCHEMATIC DIAGRAM (VCR PCB) VCR_A_MUTE P.CON+5V_A C5564 22K R5519 10 YK 33 KA 50V C5544 10V C5540_1 32 31 30 29 1.8 D5502 1.8 V.REC_ST_H 28 27 26 25 24 HA1 23 22 21 HA2 20 18 1.8 HIFI_ENV C5556 0.01 B 20 2.5 0 HIFI_H.SW C5549 0.1 F C5557 0.1 B P.CON+5V_A C5559 6.3V 47 KA 0.6 0 0.7 5 L5503 4.9 C5566 82P CH C5565 82P CH FROM/TO Y/C/AUDIO/HEAD AMP 22uH 0305 HF2 C5560 0.01 F C5558 0.01 F HF1 0 HF_COM 0 C5552 0.1 B 2.
PAGE 69
A B C D E F G H DIGITAL COMB FILTER SCHEMATIC DIAGRAM (VCR PCB) 8 8 C1511 C1506 27P CH 0.47 B W820 3.0 C1509 2.4 TO Hi-Fi/DEMODULATOR 470 YK TUNER_AUDIO 0.01 B 0.01 B C1505 0.01 B C1507 6.3V 7 P.CON+5V C1518 7 C1519 0.1 B 7 0 KILLER DVDD BIAS3 VFIL CKIN DVSS 14 13 12 11 10 9 C1512 27K 2.5 R1510 COMB_FSC C1521 50V 3.3 R1513 Y/C_VIDEO 1K KANP Y/C_VIDEO-Y CH 6 39P 560 C1523 R1512 24K 1K R1511 1.9 100P CH 5.4 0 2.5 R1507 C1513 0.
PAGE 70
A B C D E F G H DVD IN/OUT SCHEMATIC DIAGRAM (VCR PCB) 8 8 TO SOUND AMP/SURROUND FROM/TO MPEG/MICON/DSP CP8001 (CD4002) A2001WV2-11P 1 GND RX 5 GND(M) 6 P.CON+9V 7 P.CON+D5V 8 P.CON+3.3V 9 P.CON+3.3V 10 GND AUDIO_OUT_L 25V C8019 56P CH 10 KA P.CON+9V_DH P.CON+5V_D AUDIO SW IC IC8001 MM1501XNRE S801Y C8017 SPDIF-134 Vin1 GND SW_AUDIO_OUT_L 4.4 8.6 SW1 SW_AUDIO_OUT_R ZERO 0 Vin2 Vcc SW_AUDIO_OUT_L 12.4 C8006_1 25V 10 KA 6 P.CON+5V_E P.CON+12V C8012 4.
PAGE 71
A B C D E F G H REGULATOR1 SCHEMATIC DIAGRAM FROM/TO TV POWER (VCR PCB) 8 8 P.CON+12V MOTOR+12V UNREG+8V UNREG+5V OUT GND SW 1 2 3 4 100 YK W809 5.0 5.0 5.0 VCR_POWER_H P.CON+8V 7 AT+30V 5.0 180 1/4W R3024 C3002_1 10V GND P.CON+12V BUFFER Q3015 2SC2412K 10 YK R3015 0 R3023 470 5.0 6.3V 1000 YK 6.3V 7.5 C3001 5.0 +B AT5.7VREG P.CON+5V IN C3005 5.6 D3005 11EQS04N TO DIGITAL COMB FILTER 0.1 B C3009 7 D3008 7.0 BACKUP+5V Q3014 KTC3209_Y R3001 100 1/4W P.
PAGE 72
A B C D E F G H TV POWER SCHEMATIC DIAGRAM (VCR PCB) 8 8 FROM/TO MICON POWER_FAIL DEGAUSS_H C1717 GND 1/2W 2.7M +-10% R1702 C1729 2KV 390P R TO CHROMA/IF MOTOR+12V MOTOR_GND GND 14 R1720 +B ADJ R1725 56K 1/2W C1720 160V 220 YXF 0.0012 FROM/TO DVD IN/OUT 12.0 18 6.5 500V 0.0033 B D1712 D1704 D1722 R1728 R1703 R1727 1K 100 1/2W 1/4W NC +B 1 +B 2 NC 3 GND 4 GND 5 GND 6 P.
PAGE 73
A B C D E F G H DEFLECTION SCHEMATIC DIAGRAM 8 8 (DEFLECTION PCB) V.OUTPUT IC IC401 LA78041 THERMAL PROTECTION - AMP + 1 PUMP UP VCC GND 2 3 4 4.0 25.0 2.0 0 5 6 7 7 25.0 12.0 4.0 R418 C438_2 680 1/2W 680 1/2W R450 R437 100V 0.22 MKT C443 VR404 2.2K METAL R415 560 1/2W V801 A60LVY196X11(OL) CP404_1 A1561WV2-A6P L402 NC ELH5L4113 R454 NC 9 10 8 6 11 4 3 2 1 5 7 1 TO VCR DECK R423 R417 1SS133 220 2W R430 2.7 10W C 0 SW Q408 KTC3207 1 GND 0 160V 4.7mH 3.
PAGE 74
A B C D E F G H CRT/OPERATION SCHEMATIC DIAGRAM (CRT PCB) 8 8 TP802 CRT BLOCK R814 12K 2W 41 R822 2.7K 1/4W RED AMP Q802 2SC4217 R805 7 123.5 7 7.8 560 1/4W 7.3 D802 1SS133 7.3 W832 3.0 R806 1 6 D805 GND 3 R.OUT 4 G.OUT 5 C815 W831 CUT OFF 2 R817 CP603B (CP603) A2001WV2-8P W838 2.4 1K 1/4W 180 1/4W FROM CROMA/IF RED AMP Q803 KTC3199_Y 470P CH 1SS133 R815 TP801 B.OUT 6 6 12K 2W 42 R821 CLAMP_OFF 7 NC 8 NC R810 2.
PAGE 75
B 1 1 1 T- GND 1 1 GND T+ 2 2 2 T+ GND 2 2 GND F- 3 3 3 F- TX 3 3 TX F+ 4 4 4 F+ RX 4 4 RX MON(DVD) 5 5 5 GND(M) 5 5 GND(M) P.CON+9V NC(SW) 6 6 6 6 6 P.CON+9V VOL(DVD) 7 7 7 VOL(DVD) P.CON+5V 7 7 P.CON+D5V 8 8 8 GND(DVD) (P.CON+3.3V) 8 8 P.CON+3.3V LD(DVD) 9 9 9 LD(DVD) 9 9 P.CON+3.
PAGE 76
WAVEFORMS MPEG/MICON/DSP AUDIO/VIDEO Y/C/AUDIO/HEAD AMP 10ns 500µs 20µs 100mV 500mV 1.0V 1 6 11 100ns 500µs 2µs 100mV 500mV 1.0V 7 2 12 MEMORY 5ns 200mV 10µs 200mV 3 8 1ms 1.0V 13 RF AMP/DSP 200ns 500mV 100µs 200mV 5ms 2.0V 4 9 14 200ns 100mV 10µs 100mV 20µs 20V 5 10 15 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
PAGE 77
WAVEFORMS MICON 20ms 20µs 200V 10ms 10V 2.0V DEFLECTION DEFLECTION 16 26 21 MICON 1ms 10ms 2.0V 10V 50µs 2.0V 17 22 27 SOUND AMP/SURROUND 1ms 50µs 10ms 200mV 10V 2.0V 28 23 18 DVD IN/OUT DEFLECTION 10ms 50µs 0.5V 5.0V 19 1.0V 2.0V 29 24 Hi-Fi/DEMODULATOR 1ms 1ms CHROMA/IF 1ms 20µs 0.5V 2.0V 30 20 25 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
PAGE 78
WAVEFORMS DIGITAL COMB FILTER 20µs 0.5V CRT/OPERATION 20µs 1.0V 20µs 50V 36 41 31 0.5ms 20µs 20µs 0.5V 1.0V 50V 32 42 37 CHROMA/IF 20µs 10ms 0.5V 1.0V 33 0.5µs 100mV 34 20µs 1.0V 35 20µs 50V 43 38 50µs 0.5V 39 50µs 2.0V 40 NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
PAGE 79
MECHANICAL EXPLODED VIEW 214 128 118 214 214 102B 214 208 102B 201 134 214 134 102A 130 214 102 102B 201 113 PCB110 (CRT PCB ASS'Y) 129 111 215 130 201 131 SP351 129 212 130 131 215 201 130 111 215 131 SP352 129 212 111 101K 131 212 215 129 101K 101B 111 212 101I 212 101H 101D 212 101K 212 101L 212 101F 101J 101E 212 202 101C 202 212 202 212 212 212 101K 101G 101J 202 A 133 101L 101A 101 I1-1
PAGE 80
MECHANICAL EXPLODED VIEW 208 126 208 204 208 123 208 126 119 204 120 208 208 204 208 115 208 208 208 209 114 216 209 114 PCB130 (DVD PCB ASS'Y) 124 216 213 125 208 213 108 105 PCB010 (VCR PCB ASS'Y) 104 104 213 106 208 110 210 205 213 208 207 207 205 110 103 107 207 116 109 121 137 136 208 208 126 203 117 211 208 132 PCB270 (OPERATION PCB ASS'Y) 135 206 208 208 208 206 210 208 132 205 127 207 208 207 208 203 122 I1-2 A 207 112 PCB080 (DEFLECTION PC
PAGE 81
CHASSIS EXPLODED VIEW (TOP VIEW) 300 505 CD1501 349 M2003 UN4001 333 334 504 501 335 H5002 342 H5001 336 314 324 341 347 503 315 306 323 331 508 322 508 305 301 302 312 AA 313 AA 332 AA AB AB AA AB CD1502 M101 318 304 325 309 AC AB 307 AD 319 AA AC AB 345 320 AE 506 346 AE 507 AB 316 317 AB 348 321 510 AB AE AE CLASS GREASE PART NO.
PAGE 82
CHASSIS EXPLODED VIEW (BOTTOM VIEW) 303 300 501 M2001 350 CD1501 AA CD1502 339 338 AA 502 AA 502 AA 329 337 AD AA AA 509 AA 340 AA 311 310 AB 308 AB 344 327 343 AA 326 AB 328 AA 505 330 CLASS GREASE PART NO. PART NAME NOTE: Applying positions AA, AB, AC, AD and AE for the grease are displayed for this section. Check if the correct grease is applied for each position.
PAGE 83
DVD DECK EXPLODED VIEW 611 600 608 612 AA Cannot supply by a unit. 704 610 614 AA AA AA AA AA 613 AB 602 AA AA 609 AA 615 M2603 607 SW1 AB PCB610 (LOADING MOTOR PCB ASS'Y) 705 617 CD2301 701 SW2 CD2302 604 616 705 618 PCB640 (SW PCB ASS'Y) 702 CD2001 703 606 605 Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more. If the repair is needed, replace the DVD MECHA ASS'Y. 603 M2602 605 601 CLASS PART NO.
PAGE 84
MECHANICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
PAGE 85
CHASSIS REPLACEMENT PARTS LIST REF. NO. PART NO.
PAGE 86
DVD DECK REPLACEMENT PARTS LIST REF. NO. PART NO.
PAGE 87
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO.
PAGE 88
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. DESCRIPTION REF. NO. PART NO.
PAGE 89
ELECTRICAL REPLACEMENT PARTS LIST REF. NO. PART NO. *** ! J801 ! J2201 J2202 J2203 J2204 J4201 J4202 J8007 066F130021 060J131016 060J421036 060J421037 060J421030 060J431020 060J411031 060J401102 060J401082 DESCRIPTION RESISTORS *** JACKS SOCKET,CATHODE RAY,TUBE HEADPHONE JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK REF. NO. PART NO.
PAGE 90
SPEC.NO. M5Q0-046 O/R NO.