MPH2089 O/M.QXD 9/4/01 10:30 AM Page 21 DIGITAL ANSWERING MACHINE WITH DATE/TIME STAMP MODEL: MPH2089 BEFORE OPERATING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS COMPLETELY.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 1 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 2 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on this product. 3. Do not use this product near water- for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 3 IMPORTANT SAFETY INSTRUCTIONS 1. If your local telephone exchange only accepts Pulse dialing, you may have to switch the Tone/Pulse switch to Tone to access certain services that require Tone signalling (such as home banking). After the initial line is connected to the number you are calling, switch the Tone/Pulse switch to Tone to access Tone signalling. When you have completed your call, please switch the Tone/Pulse switch back to Pulse. 2.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 4 LOCATION OF CONTROLS 1 2 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 5 INSTALLATION This section has been designed to provide a reference guide to help set up the unit. AC POWER ADAPTOR DC 9V POWER TELEPHONE JACK LINE JACK DATA JACK TELEPHONE LINE CORD TO EXTERNAL TELEPHONE 1. Unpack and make sure all the items have been included: Base Unit, Power Adaptor and Telephone Line Cord. 2. Connect one end of the provided telephone line cord into the LINE jack on the rear of the unit and the other end into a modular telephone jack. 3.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 6 POWER SOURCES AC Power Adapter To operate the unit using AC power, connect the AC adapter to the DC jack on the rear of the unit and to a wall outlet having 120V, 60Hz only. CAUTION: Use only the AC adapter provided with the unit. Using another AC adapter may damage the unit. When not using AC power, disconnect the AC Outlet AC adapter from the wall outlet by pulling the plug (not the cord). Do not touch the AC adapter with wet hands.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 7 OPERATION SETTING THE DATE/TIME 1 2 2 3 1 2 3 1 Press and hold the TIME button ❶ for 2 seconds and the unit will announce the day of the week (i.e. Monday). Press the SKIP➛➛/MEMO button ❷ to decrease or the SKIP❿❿/OGM button button ❸ to increase until the present day of the week is heard. Press the TIME button ❶ again and the unit will announce the hour of the time (i.e. 12 AM).
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 8 OPERATION (CONTINUED) RECORDING OGM (OUTGOING MESSAGE ) Recording an OGM allows the caller to hear the OGM and then be able to leave a message. Please note that there is an automatic message on this unit, recording a new OGM will disable this default message. 1 2 1 2 When finished recording, press the PLAY/STOP button ❶. The newly recorded outgoing message will then play once. Make sure the VOLUME control ❷ is at a desirable level.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 9 OPERATION (CONTINUED) SETTING THE UNIT TO ON MODE (Incoming Messages will be recorded) When the answering machine is turned on, when a call is received the unit will play the OGM and then record a message. 1 Make sure the OGM is recorded.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 10 OPERATION (CONTINUED) RECORDING/PLAYING A PERSONAL MEMO 1 To record a personal memo which will be played the next time somebody retrieves the memos, press and hold the SKIP➛➛/MEMO button for approximately 2 seconds; a beep will sound. When the beep is heard, release the SKIP➛➛/MEMO button. 2 2 1 After the message is recorded, press the PLAY/STOP button ❶ to stop the recording. “oo” will appear in the display when memo’s have been recorded.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 11 OPERATION (CONTINUED) PLAYING BACK INCOMING MESSAGES (ICMs) The NEW MESSAGE indicator will blink when the unit has recorded new messages and the display will show the total amount of messages. To hear messages, proceed as follows: 1 2 Make sure the SPEAKER VOLUME control is adjusted as desired. Press the PLAY/STOP button to hear only the new ICM/MEMO messages.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 12 OPERATION (CONTINUED) 5 CHANGING THE REMOTE CODE To change the remote code, please follow the instructions given on page 17. NOTES: • If a power failure occurs and there is a dead or no battery, the Remote Code resets to 000. • If you forget the Remote Code, unplug the AC adaptor and disconnect the battery and it will reset to 000. • Be sure to write down your new Remote Code and store it in a safe place.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 13 REMOTE OPERATION TURNING THE ANSWERING MACHINE OFF 1 2 Call the answering machine from a separate line. After the OGM is played (press “*” to skip OGM), and the beep is heard, enter your remote code within 10 seconds. Press the “*” pad, then the “5” pad to turn the unit off. REMOTELY PLAYING THE OGM (OUTGOING MESSAGE) 1 2 Call the answering machine from a separate line.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 14 REMOTE OPERATION REMOTELY PLAYING INCOMING MESSAGES (ICM’S) 1 2 Call the answering machine from a separate line. After the OGM is played (press “*” to skip OGM), and the beep is heard, enter your remote code within 10 seconds. Press the “4” pad to play all messages or the “5” pad to play only new messages. TO ENTER THE PLAYBACK MENU 1 2 Call the answering machine from a separate line.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 15 REMOTE OPERATION (CONTINUED) TO STOP PLAYBACK TO DELETE A MESSAGE 1 1 WHILE IN THE PLAY MENU: To stop playback, press the “7” pad. WHILE IN THE PLAY MENU: To delete a message, press the “6” pad. TO PAUSE PLAYBACK. RECORDING A MEMO 1 1 WHILE IN THE PLAY MENU: To pause playback, press the “4” pad. To release pause, press the “4” pad again. After the OGM is played, and the beep is heard, enter your remote code within 10 seconds.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 16 REMOTE OPERATION (CONTINUED) ERASING ALL MESSAGES 1 After the OGM is played, and the beep is heard, enter your remote code within 10 seconds. Press the “*” pad, followed by the “4” pad to erase all ICMs and memos. REMOTE ROOM MONITORING This feature will allow you to call in and monitor the room in which the answering machine is located. 1 2 After the OGM is played, and the beep is heard, enter your remote code within 10 seconds.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 17 REMOTE OPERATION (CONTINUED) TO CHANGE THE REMOTE CODE (REMOTELY) 1 2 After the OGM is played, and the beep is heard, enter your remote code within 10 seconds. Press the “*” pad, followed by the “3” pad to change the remote code. STOP CALL: Press the “#” pad to stop the remote function. TO CHANGE THE REMOTE CODE (FROM THE UNIT) 1 2 1 Press and hold the ON/OFF button for 2 seconds; the display will show “se” and the remote number.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 18 CONVENIENT REMOTE ACCESS CARD For your convenience, cut out this card and keep it in your wallet as a reference guide when remotely calling your answering machine. IDLE MODE (No Messages Playing) Button Function 1 Play OGM 2 Starts room monitoring 3 Playback memos 4 Playback all ICMs 5 Playback new ICMs 7 Stop or save all messages 9 Enter the Playback menu.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 19 TROUBLESHOOTING GUIDE Before requesting service, please refer to the following chart and check for the symptom you are experiencing. SYMPTOM No Power. POSSIBLE CAUSE AC adaptor not connected to unit. AC adaptor not connected to the AC outlet. No power. No OGM. No OGM recorded. Volume is too low. Message recorded too low. Unit not answer- Line cord(s) are not ing the phone. connected properly. Unit is not on. Phone line problems. No sound. Volume is too low.
MPH2089 O/M.QXD 9/4/01 10:30 AM Page 20 Memcorp, Inc. Weston, FL Printed in Hong Kong Visit our website at www.memcorpinc.
