USE AND CARE GUIDE FOR MODEL MES2B/W/R/K/MG, MES2B/W/R/K/MGCAN READ AND SAVE THESE INSTRUCTIONS Pod Brewing System
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: • Read all instructions. • Do not touch hot surfaces. Use handles or knobs. • To protect against fire, electric shock, do not place cord, plugs, or appliance in water or other liquid. • Close supervision is necessary when any appliance is used by or near children. • Unplug from outlet when not in use and before cleaning.
ADDITIONAL IMPORTANT SAFEGUARDS WARNING: This appliance generates heat and escaping steam during use. Use proper precautions to prevent the risk of burns, fires, or other injury to persons or damage to property. • All users of this appliance must read and understand this Owner’s Manual before operating or cleaning this appliance. • The cord to this appliance should be plugged into a 120V AC electrical outlet only.
POLARIZED PLUG: This appliance has a polarized plug, (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.
Your product may vary slightly from illustration. Parts Identification Pod (Samples included in box. To order, see page 15.
Before Using Your One:One™ Pod Brewing System Become familiar with all parts of the appliance. Keep your One:One clean Clean and descale your One:One™ on a regular basis. See “Cleaning and Descaling”, pages 12-13. We recommend cleaning the Water Tank and the Drip Spout(s) as well as the Pod Holder(s), before using your One:One™ for the first time. Turn on the machine for a full cycle using water only by following steps 1-7 below.
2. Fill the Water Tank with fresh water up to the ‘Max’ line, and fit back into the Base (down and in) until it “snaps” into place, see Figure 5. FIGURE 5 3. Lift Lid by pulling out on the Lever. Top will pop up. Push back so Lid is in fully raised position, see Figure 6. FIGURE 6 4. Place the appropriate spout, coffee, hot or ice tea, inside the One:One™.
5. Make sure the Pod Holder is inside the Pod Chamber. Do not place a tea or coffee pod in holder. See Figure 7. When brewing coffee or tea, use the black pod holder for coffee and the grey pod holder for tea. FIGURE 7 6. To close the Lid, press down firmly on the top of the Lid and hold in place while pushing the Lever back so it is flush with the Lid and locks into place, see Figure 8. FIGURE 8 7. Place a cup or mug below the Drip Spout to collect the water.
8. Press the Power Light/Indicator Button to turn power on, then simultaneously press the 5-Ounce Serving and 8-Ounce Serving Buttons, see Figure 9. FIGURE 9 The water from the Water Tank will cycle through the One:One™. Note: If unit goes unused for 3 or more days, please repeat above process (steps 1-7). CAUTION: Do not immerse cord, plug or machine in water or other liquid.
5. Place the empty Pod Holder inside the Pod Chamber, see Figure 7. Note: When brewing coffee or tea, use the black pod holder for coffee and the grey pod holder for tea. 6. Place one Melitta® javapod™ or Cooper’s® teapod™ inside the Pod Holder. Press lightly on the javapod™ or teapod™ to make sure it sits evenly in the Pod Holder. See Figures 10 and 11 for correct pod insertion.
10. Select the amount of coffee or tea you wish to brew: either a 5 ounce serving or an 8 ounce serving. When brewing tea, the 8 ounce serving is recommended.The machine will begin the brewing process. At the beginning of the brewing cycle, a small amount of water is dispersed to saturate the pod to ensure full extraction. Following a pause, the machine will brew for about 50 seconds for coffee (or 35 seconds for tea).You can manually stop the brewing process at any time by pressing the Power Button.
Helpful Hints for Brewing Fresh Water For optimal results, use fresh water daily. If you haven’t used your machine for a few days, follow steps 1-7 in section “Before Using Your One:One™ Pod Brewing System” pages 6-9. Note: If Water Tank becomes dry for 3 or more days, revisit section “Before Using Your One:One™ Pod Brewing System,” steps 1-7. Javapods and Teapods Remember to remove pods after use.
4. Remove the Drip Tray and Overflow Tray, see Figure 14. FIGURE 14 5. Clean the Water Tank, Pod Holder, Pod Chamber, Drip Spout, Drip Tray and Overflow Tray with hot water. If necessary, use a little dish soap. Note: The Pod Holder, the Drip Tray, Overflow Tray and the Drip Spout may be washed in the dishwasher (top shelf only). The top part of the tank can be removed for thorough cleaning. Do not place the Water Tank in the dishwasher. 6. Rinse all parts with fresh water after cleaning.
Troubleshooting Should a problem occur, you may be able to find an answer in the text below. If the text proves unhelpful or if you require further information, please contact Consumer Service. 1. The coffee or tea is too weak. Check the following: • the pod is placed properly in the Pod Holder. You may need to lightly press it down into the holder. correct incorrect FIGURE 15 • you have selected the correct button according to the number of ounces and strength desired.
5. The indicator light is flashing. A flashing indicator light means the machine is heating. This normally lasts for 11/2-2 minutes. If indicator light is flashing rapidly (more than a second apart), see #6 below. If the indicator light flashes continually for more than 4 minutes, contact Consumer Service. 6. The indicator light keeps flashing at rapid intervals. Check the following: • the Water Tank must be inserted properly inside the appliance. • there must be enough water in the Water Tank.
IMPORTANT NOTICE If any parts are missing or defective, DO NOT return this product. Please call our Customer Service Department for assistance. 800-841-1628 Monday - Friday 9:00 am - 5:00 pm CST Thank You LIMITED ONE YEAR WARRANTY Warranty: This Melitta® product is warranted by Salton, Inc. to be free from defects in materials or workmanship for a period of (1) year from the original purchase date. This product warranty covers only the original consumer purchaser of the product.
Out-of-Warranty Service: A flat rate charge by model is made for out-of-warranty service. Include $12.00 (U.S.) for return shipping and handling. We will notify you by mail of the amount of the charge for service and require you to pay in advance for the repair or replacement. For products purchased in the USA, but used in Canada: You may return the product insured, packaged with sufficient protection, and postage and insurance prepaid to the USA address listed below.
