MT90 Applications & Manual Guide Version 1.
Table of Contents PRODUCT OVERVIEW .......................................................................................... 1 1. PRODUCT FEATURES .................................................................................. 1 1.1. 1.2. 2. HEALTH & SAFETY PRECAUTIONS .............................................................. 2 2.1. 2.2. 2.3. 3. View and Buttons ......................................................................................... 4 LED Indications ........................
Product Overview MT90 is a GPS/GSM/GPRS tracking device specially developed and for pets, children, personal safety and even vehicles. With superior GPS and GPRS modules, MT90 has good sensitivity and stable performance. It could also get an accurate GPS location fix even in remote places with AGPS Module embedded into the set. Through GPS and GSM or GPRS communications, MT90 can get its position and send the position data back to your mobile phone or server to be displayed on maps. 1. Product Features 1.
1.2. Specifications Items Dimension Weight Charging Voltage Back-up Battery Power Consumption Operating Temperature Humidity Work Time LED Button Microphone/Speaker Memory Sensor GSM Frequency GPS Chip GPS Sensitivity Positioning Accuracy Specification 77 x 47 x 20mm 65g Mini USB charging interface, DC4.2V~5.5V/400mA 1100mAh/3.
2.3. Hardware Precautions / Maintenance Do not disassemble, tamper or attempt to repair the tracker, components or accessories. Doing so voids your warranty. Always power OFF the tracker before loading or removing its battery or SIM Card. Do not drop, hit or otherwise abuse the tracker, components or accessories. This may damage the precision components of the tracker. Make sure all connections to the tracker are plugged in properly into the correct locations only.
3.1. View and Buttons No. 1 2 3 4 5 6 7 8 9 Item GPS LED (Blue) Description Indicating GPS and battery status, please refer to below LED indications. GSM LED Indicating GSM status, please refer to below LED (Green) indications. Answer/Hand-up Press to receive an incoming call. Button Press to complete a conversation. Long press for 2 seconds to send GPRS message to the server when no incoming call or conversation.
10 Volume-/GPRS Button 11 12 Lanyard Loop Battery Cover “BI” twice, and the logger will stop automatically. Note: you can make turn on/off function of logger (default: valid) invalid through Meitrack Manager to avoid operating failure. Light press to turn down the volume. In standby mode, long press for 2 seconds, when the buzzer “BI” once, GPRS function will be enabled automatically.
2. Insert the SIM Card Place the SIM card into the device with the gold-colored side facing down. Note: make sure there is enough credit on the SIM card. It is also important that the SIM card has Called ID Display function. If you will use GPRS function, you should pay attention to the current SIM card GPRS charge. 3. Insert the Micro SD Card Insert the Micro SD card into the slot with its gold contacts facing down and push it until it clicks into place. 4.
6. Charge with the Travel Adapter Open the cover of the multifunction jack of the device. Plug the small end of the adapter into the multifunction jack. Then plug the larger end of the travel adapter into a power outlet. Note: improperly connecting the travel adapter can cause serious damage to the device. Any damage caused by misuse is not covered by the warranty. 7. Attach A Lanyard Slide the lanyard through the slot and hook it over the small projection.
In the SMS, the values after “lat” is the latitude, the values after “lng” is the longitude. *Meitrack Manager and SMS command. The default password is 0000, password can be revised through Meitrack Manager and SMS command. MT90 will only accept commands from a user with the correct password and report SMS report to the user. If preauthorized phone number was set, only this phone number can receive SMS reports. The common format of SMS command is: password,command,parameter 4.2.
Note: the default value is empty, if the function numbers are less than three while setting, it must be added “,” to avoid setting failure. To clear the combination of monitor numbers directly sending 0000,A72 (If this function can’t be achieved, please add your Country and Area Code before your phone number when you set the preauthorized numbers, or you can also consult your local mobile operator.) 4.4. Smart Sleep Mode – A73 This command enables the sleep mode function.
Note: this value is your MT90’s IMEI number. The device will send this data automatically and these numbers don’t represent anything significant to the functionality of the tracker. Below the same applies. 4.6. More Settings You can configure MT90 by mobile phone or by computer using the Meitrack Manager to Setting Multiple Software. For more details, please refer to 5. Configuration by Computer below For more details regarding SMS commands, please refer to 6.1 Using SMS command. 5.
Run “Meitrack Manager.
5.1. SMS Tracking Items Descriptions SMS Password SMS Time Zone The defaulted value 0000 of SMS password for sending SMS commands Default time of the tracker is GMT0, you can use this to correct the trackers time to your local time for SMS report. Minute = 0, GMT0 (default)’ Minute = [-32768,32767], set time difference in minutes to GMT. Time zone for SMS is the same as GPS log, but separate from GPRS packet. A phone number to receive SMS reports, incoming call and selected event reports.
Reboot Geo-fence Alarm Monitor Phone No. SMS Track No. Save Report when MT90 reboots. SMS header defaulted as “Reboot”. Geo-fence is circle with preset radius. Max 8 geo-fence waypoints can be set. Enter alarm: report when MT90 enters geo-fence. SMS header defaulted as “Enter GEO”. Exit alarm: report when MT90 exits geo-fence. SMS header defaulted as “Exit GEO”. Add new: set radius latitude and longitude, or draw geo-fence on map directly in circle.
Backup IP/Domain and Port APN APN user name APN password GPRS Time Interval GPRS Report Times GPRS Time Zone Save Note: main IP:210.193.55.36, main port: 8500. Input backup server’s IP address and port number to avoid losing data when main server is down. The backup server will receive data automatically. APN, APN username, APN password: max 32 bytes. If no username and password required, leave them blank. Track by time interval via GPRS. Set time interval for GPRS tracking.
6. Using SMS Command NOTE: **** is user’s password and the default password is 0000. The tracker will only accept SMS commands from a user with correct password. SMS commands with wrong password will be ignored. Password is in 4 digits. Description SMS Command Example Set GPRS ****,A21,X,IP,Port,APN,APN Username,APN Password 0000,A21,1,210.193.55.46,8500,internet,, Function: To set the GPRS setting. X = 0, Close GPRS X = 1, Open TCP X = 2, Open UDP IP = IP address or domain name of your server.
Description SMS Command Example Initialization ****,F11 0000,F11 Function: To reset all the setting (except for the password) back to factory default. SMS Response: TrackerID,F11,OK Reset Password 8888,FAB 8888FAB Function: To reset password back to default factory password. Only authorized phone number is authorized to send the command.
Description SMS Command Example Add New SMS Event to Authorize Phone Number ****,B02,P,E 0000,B02,1,17 Function: To add new SMS event report to an authorized phone number P = 1, first authorized phone number. P = 2, second authorized phone number. P = 3, third authorized phone number. E = Event Code. SMS Response: TrackerID,B02,OK NOTE: Please refer to 7. Event Codes Table for more details on Event Code.
Delete Geo-fence Alert ****,B06,X 0000,B06,1 Function: To delete a set of Geo fence alert. SMS Response: TrackerID,B06,OK X = 1 to 8 Waypoint. Speeding Alert ****,B07,X 0000,B07,80 Function: To set a SMS alert when the tracker exceeds the preset speed limit. SMS Response: TrackerID,B07,OK X = Preset Speed limit. X = 0, Turn OFF the alert. X = 1~255, set the speed limit (in km/h).
Function: Tracker default time zone is GMT. You may use this command to correct the time that for SMS reporting. SMS Response: TrackerID,B35,OK X = to set time difference in minute to GMT If time is ahead of GMT, input the time difference in minute directly. E.g. 0000,B35,120 If time is behind of GMT, ‘-’ is required. E.g. 0000,B35,-120 Time Zone Setting (GRPS Reporting) ****,B36,X 0000,B36,120 Function: Tracker default time zone is GMT.
7. Tracking 7.1. Track by SMS Description SMS Command Example Track on Demand Summarised ****,A00 0000,A00 Function: Tracker sends SMS location report to the mobile phone number that sent the SMS command. Track on Demand – Google Link ****,A01 0000,A01 Function: Tracker sends SMS location report with an http link. Click on the link and it will direct to Google Map on your mobile phone. E.g. http://maps.google.com/maps?f=q&hl=en&q=22.540103,114.
Google Earth: Google Maps: 21
8.
66 Press Input 2 to Call / N/A N N/A Event Code Event Default SMS Header (max 16 bytes) Default GPRS Flag Default SMS Flag Default Picture Flag 67 Press Input 3 to Call / N/A N N/A 68 Press Input 4 to Call / N/A N N/A 69 Press Input 5 to Call / N/A N N/A 70 Reject Incoming Call / N/A Y N/A 71 Call for SMS Location Report / N/A Y N/A 72 Auto Answer Incoming Call / N/A N N/A 73 Listen-in (voice monitoring) / N/A N N/A 9.
Problem: Green LED is Flashing (1 second ON and 2 seconds OFF) Possible Cause: Resolution No GSM Signal. Check with a mobile phone to see if there is GSM signal in the area or try to call the tracker to see if there is any response. No SIM card. Insert a working SIM card. Ensure the SIM card lock (PIN code) is turn OFF. Check the SIM card using a mobile phone. SIM card has expired. Check the SIM card using a mobile phone. Replace SIM card if needed. Ensure the SIM card lock (PIN code) is turn OFF.
11. APNs Local Telecom APN - Prepaid APN - Postpaid Singtel hicard internet Starhub shppd shwap MobileOne miworldmcard sunsurf NOTE: APNs are provided by your Telecom Service Provider. Information in the table may change without prior notice. NOTE: If tracker is using overseas SIM card, it is required to change the APN provided by the abroad Telecom Service Provider.
