Mega 200V 200VWR Quick Start Guide
Mega 200VWR Package Content: ........................................................................................................................2 The Front LEDs ...........................................................................................................................3 The Rear Ports.............................................................................................................................4 Getting Started: ..............................................................
Mega 200VWR This Quick start guide describes a basic installation. For instructions on configuring an advanced setup, please refer to the on-line manual available on the enclosed CD. Package Content: Place the Mega 200VWR on a stable surface. Only use the power adapter that comes with the package. Using a different voltage rating power adaptor may damage the router. Do not use the Mega 200VWR in high humidity or high temperature rooms and/or surroundings. I.e. Kitchens.
Mega 200VWR The Front LEDs LED Meaning 1 PWR Lit when power is ON. 2 SYS Lit when the system is ready. 3–6 LAN Port 1X — 4X (RJ-45 connector) 7 WLAN 8–9 Phone 1X Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking when data is Transmitted / Received. Lit green when the wireless connection is established. Flashes when sending/receiving data. — 2X Lit green when the phone is off-hook.
Mega 200VWR The Rear Ports Port Meaning 1 Power Switch Power ON/OFF switch 2 PWR Connect the supplied power adapter to this jack. 3 RESET After the device is powered on, press it to reset the device or restore to factory default settings. 1-3 seconds: reset the device 8 seconds above: restore to factory default settings (this is used when you can not login to the router, e.g. forgot the administrative password).
Mega 200VWR Getting Started: Advanced users: Attention 5 Advanced users may access the router’s graphical user interface on the following IP address: 10.0.0.2 The default username and password is “admin” and “admin”. Important Note: It is a security risk to leave your administration password as default, it is recommended to change it. Please refer to the installation process or online user manual for assistance.
Mega 200VWR Installation & Setup: (Windows XP or Windows 2000) An Easy Setup Wizard has been developed to simplify the setup process for users running the newer versions of Windows. The process has been well documented and online help/supplementary info has been provided for each step. The wizard will require the .Net framework to be installed on your PC in order to function properly.
Mega 200VWR Click the “PC Qualification Test” button on the menu screen. A diagnostic program will open to verify that your PC meets the minimum requirements. Just follow the instructions and when complete, close the program to return to the menu screen and proceed to the next step. If you encounter any problems or have any questions, please contact the helpdesk for which the contact information is provided in the last section of this quick start booklet. 2.
Mega 200VWR c. Launch the Mega 200VWR Easy Setup Wizard: Launch the Easy Setup Wizard by selecting it under the “Start > All Programs> Mega 200VWR” menu – see figure below. The wizard, consisting of 7 compulsory steps, will assist you to: setup your Mega 200VWR hardware, configure your network card, verify your Telkom ADSL service, setup your ISP, VoIP & E-Mail account information and perform other administrative actions, it will take approximately 15 minutes. Please complete all the steps.
Mega 200VWR Please note that this printed booklet does not document all the steps of the online Easy Setup Wizard. For assistance, please read the supplementary information provided. After you have completed all the Easy Setup Wizard steps you will be able to surf the internet and make VoIP calls. 3. Open the User’s Manual: This button will open the online user’s manual.
Mega 200VWR Setting up VoIP accounts on your Mega 200VWR: During the easy install process, you had the option to register Telkom Internet Communicator VoIP account(s). These account details were e-mailed to an e-mail address specified by yourself. If the e-mail did not arrive in time and you have not completed the VoIP account setup during the easy setup wizard, this step will assist you in setting up the accounts by utilizing the separate router management app. See figure below. 1.
Mega 200VWR On successful completion of the save process a message will be displayed. Note that setup requires restarting your router in order to complete VoIP account configuration. Click “Yes” when prompted to restart. 4. Once your router has completed the restart, the VoIP LED will light up. This indicates that the VoIP account has been configured and successfully registered with the Telkom VoIP server. You are now ready to make cost-effective Internet telephone calls. 11 TLK/200VWR-v1.
Mega 200VWR Getting Started using a wireless connection: 1. The Mega 200VWR’s wireless access point name (SSID) is ‘wlan-ap’. When you scan for wireless networks using your wireless client, this is the name that will be displayed. 2. To ensure wireless security “out-of-the-box”, Telkom distributes each Mega 200VWR with a unique WPA pre-shared security key already setup on your router.
Mega 200VWR Troubleshooting: Problem Description 1: ADSL/PPP LED (light) does not come on. Solution: 1. Check ADSL line connection from telephone wall socket to ADSL port on router. Make sure that the cable is securely connected. 2. Make sure that no micro filters are connected directly between the telephone wall socket and the router’s ADSL port. 3.
Mega 200VWR used by default. If you have changes the setting on a previous occasion, please open the advanced section of the utility to enter the new information. Problem Description 4: When the wizard tries to open the Telkom website or when I try to open any other website, a Dial-up Connection screen pops up asking me to connect to the internet. It doesn’t matter what choice I make I can not connect or see the website. Solution: 1.
Mega 200VWR Product Support and Contact Information Most problems with setting up the router can be solved by referring to the Troubleshooting section in the User Manual on the enclosed CD. If you cannot resolve the problem using the Troubleshooting above, please contact 0860 2C HELP (0860 22 43 57). Windows 98, Windows NT, Windows 2000, Windows Me and Windows XP are registered Trademarks of Microsoft Corporation. 15 TLK/200VWR-v1.
