User manual

8
This function allows you to select what operating mode you would like to use 15CH or 19CH. Press Enter use the ▲ or ▼ to select the desired
DMX profile mode. Press Enter to confirm the setting .
Channel Mode
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This function allows you to invert the Pan via display command. Press Enter use the ▲ or ▼ to select pan rotation configuration. Press Enter
to confirm the setting .
Invert Pan
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This function allows you to invert the Tilt via display command. Press Enter use the ▲ or ▼ to select Tilt rotation configuration. Press Enter to
confirm the setting .
Invert Tilt
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This function will Swap the Pan Tilt channel on DMX control via display command. Press Enter use the ▲ or ▼ to select Swap the DMC chan-
nels for the Pan & Tilt Press Enter to confirm the setting .
CH 1&2 Pan CH 3&4 Tilt =OFF
CH 1&2 Tilt CH 3&4 Pan =ON
Swap Pan-Tilt
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This function will allow you to enable or disable the encoders for the Pan and Tilt. Press Enter use the ▲ or ▼ to select ON or OFF Press
Enter to confirm the setting .
(note) encoders are electronics that will reposition the unit if it manually moved.
Encoder Pan-Tilt
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
If DMX signal is removed or terminated the fixture will keep the last command or it will clear the command and place the fixture at 0 on all
channels. Press Enter use the ▲ or ▼ to select KEEP or CLEAR Press Enter to confirm the setting .
No DMX Signal
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This command will allow you to select to leave the display permanently on when the fixture is on, or it will let you turn off the display after 30
seconds of no pressing the buttons. Press Enter use the ▲ or ▼ to select OFF or ON Press Enter to confirm the setting .
Display Power Save
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►
This command will allow you to restore the fixture display commands to the factory setting . Press Enter to access the command and press
Enter to reset and Menu to cancel.
Load Default
Run Mode
DMX Address
Channel Mode
Invert Pan
Invert Tilt
Swap Pan-Tilt
Encoder Pan-Tilt
No DMX Signal
Display Power Save
Load Default
DMX
001
15CH
OFF
OFF
OFF
ON
KEEP
OFF
►