Operating instructions

ManualsBrandsMedtronic ManualsFitness EquipmentLIFEPAK CR-T

LIFEPAK

CR–T

AED Trainer

After receiving the LIFEPAK CR–T AED Trainer, carefully remove the Trainer and the operating instructions from the

shipping container. Examine the Trainer and accessories for any sign of damage during shipping.

Shipping container contents include:

If any components are missing or the Trainer appears to be damaged, contact your dealer or local Medtronic

representative right away. Save the container for reshipping the Trainer if necessary.

Always place the Trainer in a location separate from the defibrillator to avoid confusion in real emergencies.

SETUP INSTRUCTIONS

• LIFEPAK CR–T AED Trainer

• Remote control

• Remote control cable

• Yellow plastic shock key cover

• CHARGE-PAK™ Trainer

• Quick reference card

• QUIK-PAK™ training electrodes

• 2 AAA alkaline batteries (for remote control)

• 4 D-cell alkaline batteries (for Trainer)

• Operating instructions

• Lid labels (international trainers only)

• Soft case with identification card

Accessory Bag

Accessory

Bag

D-Cell

–

D-Cell

–

D-Cell

–

D-Cell

–

AAA

–

AAA

–

Summary of content (56 pages)

PAGE 1
SETUP INSTRUCTIONS LIFEPAK® CR–T AED Trainer After receiving the LIFEPAK CR–T AED Trainer, carefully remove the Trainer and the operating instructions from the shipping container. Examine the Trainer and accessories for any sign of damage during shipping.
PAGE 2
Soft Case Medtronic, Inc. 11811 Willows Road NE Redmond, WA 98052-2003 USA Telephone: 425.867.4000 Toll Free (USA only): 800.442.1142 Fax: 425.867.4121 Internet: www.medtronic-ers.com Medtronic Europe S.A. Rte. Du Molliau 31 Case postale 84 1131 Tolochenaz Switzerland Telephone: 41.21.802.7000 Fax: 41.21.802.7900 Medtronic and LIFEPAK are registered trademarks of Medtronic, Inc. CHARGE-PAK and QUIK-PAK are trademarks of Medtronic, Inc. Specifications are subject to change without notice.
PAGE 3
LIFEPAK CR–T ® AED Trainer Operating Instructions
PAGE 4
PAGE 5
OPERATING INSTRUCTIONS LIFEPAK® CR–T AED Trainer
PAGE 6
Text Conventions Throughout these operating instructions, special text characters are used to indicate labels and voice prompts: • Operating control labels: CAPITAL LETTERS such as LID RELEASE/ON-OFF. • Voice prompts: CAPITAL ITALICIZED LETTERS such as CALL FOR HELP NOW. Version History These operating instructions describe the LIFEPAK CR–T AED Trainer, MIN 3201804-005 or later. Medtronic , Inc. 11811 Willows Road NE Redmond, WA 98052-2003 USA Telephone: 425.867.4000 Toll Free (USA only): 800.442.
PAGE 7
TABLE OF CONTENTS 1 1 Getting Started Introduction ............................................................................................................................................. 2 Unpacking and Inspecting the LIFEPAK CR–T AED Trainer .................................................................. 2 Controls, Indicators, and Labels ............................................................................................................. 3 Outside Controls, Indicators, and Labels ......
PAGE 8
CPR Time...................................................................................................................................... 21 Language Option........................................................................................................................... 21 Setup .................................................................................................................................... 22 Resetting Default Settings........................................................
PAGE 9
LIST OF FIGURES Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Top and Bottom) ........ 3 LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Back and Side) .......... 4 LIFEPAK CR–T AED Trainer Inside Features ........................................................................... 5 Inside Features after Opening the Electrode Packet ...............
PAGE 10
PAGE 11
Getting Started 1 GETTING STARTED This section introduces the LIFEPAK® CR–T Automated External Defibrillator (AED) Trainer and provides an orientation to its features. Introduction Unpacking and Inspecting the LIFEPAK CR–T AED Trainer Controls, Indicators, and Labels Installing and Replacing Batteries LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 12
Getting Started INTRODUCTION The LIFEPAK CR–T AED Trainer provides the necessary interface for practical skill demonstration during a simulated cardiac arrest. The Trainer is designed to assist the instructor with realistic training on the use of the defibrillator without the actual charge and discharge of electrical energy. The Trainer simulates voice prompts, audible tones, and readiness display features of all LIFEPAK CR defibrillator models.
PAGE 13
Getting Started Getting Started CONTROLS, INDICATORS, AND LABELS There are several important controls, indicators, and labels on the LIFEPAK CR–T AED Trainer with which you should become familiar. Outside Controls, Indicators, and Labels The outside controls, indicators, and labels are identified in Figure 1 and Figure 2 and described in Table 1 and Table 2.
PAGE 14
Getting Started Table 1 Outside Controls, Indicators, and Labels (Top and Bottom) (Continued) 4 CHARGE-PAK Trainer The CHARGE-PAK Trainer is not functional. It is used only to demonstrate how to remove and replace the CHARGE-PAK. 5 Lid release/On-Off button Button that opens the Trainer lid and simulates turning on the defibrillator. Pressing this button for approximately 2 seconds after the lid is open simulates turning off the defibrillator.
PAGE 15
Getting Started Getting Started Inside Features When the Trainer lid is opened, you will see the electrode packet and the release handle shown in Figure 3. Figure 4 shows the features you see after releasing the electrode packet. Table 3 and Table 4 describe the inside features shown in Figure 3 and Figure 4. 15 16 17 18 19 Figure 3 LIFEPAK CR–T AED Trainer Inside Features Table 3 Inside Features 15 Quick reference card An illustrated and condensed guide for using the Trainer.
PAGE 16
Getting Started 25 20 21 24 23 22 Figure 4 Inside Features after Opening the Electrode Packet Table 4 Inside Features after Opening the Electrode Packet 20 Speaker Speaker that projects the voice prompts and tones. 21 Electrode pad indicators Indicators that automatically flash red when the Trainer lid is opened, alerting the trainee that the electrode pads are NOT applied to the training manikin.
PAGE 17
Getting Started Getting Started Remote Control and Remote Control Cable The remote control is stored in the remote control compartment (refer to page 4). The dual-function keys are used to configure the Trainer operating settings prior to a training session and to alter simulation during training scenarios. The remote control communicates with the Trainer through signals to the infrared sensor located in the back of the Trainer.
PAGE 18
Getting Started INSTALLING AND REPLACING BATTERIES The following paragraphs provide the procedures for installing or replacing LIFEPAK CR–T AED Trainer and remote control batteries. Installing and Replacing Trainer Batteries Four D-cell alkaline batteries provide power to the Trainer. The batteries are installed in a compartment in the bottom of the Trainer. Fresh batteries provide approximately 100 hours of continuous Trainer operation.
PAGE 19
Using the LIFEPAK CR–T AED Trainer 2 USING THE LIFEPAK CR–T AED TRAINER This section provides information and instructions for using the LIFEPAK CR–T AED Trainer. Voice Prompts and Tones Using the Remote Control Preparing for a Training Session Conducting a Training Session Following a Training Session LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 20
Using the LIFEPAK CR–T AED Trainer VOICE PROMPTS AND TONES The LIFEPAK CR–T AED Trainer voice prompts provide the trainee with step-by-step instructions for responding to training scenarios. For a complete list of voice prompts, refer to Appendix A. USING THE REMOTE CONTROL The remote control allows the instructor to: • • • • Preset operating settings in a setup configuration (refer to Section 3, beginning on page 15). Pause LIFEPAK CR–T AED Trainer operation.
PAGE 21
Using the LIFEPAK CR–T AED Trainer Table 6 Remote Control Button Functions (Continued) Button T1 Function Change shock to no shock advised Operation and Description The NO SHOCK ADVISED button can be used only during simulated analysis. Press the NO SHOCK ADVISED button to change any shock within a shock protocol to NO SHOCK ADVISED.
PAGE 22
Using the LIFEPAK CR–T AED Trainer Table 6 Remote Control Button Functions (Continued) Button OP Function L Adjust volume of voice prompts Operation and Description Each time the Trainer is turned on, the volume level defaults to the level used during the previous session. Three volume levels are available (low, medium, high). Press the VOLUME CONTROL button to select the volume level desired. As you press the button, the volume increases. View the LED display to observe volume changes.
PAGE 23
Using the LIFEPAK CR–T AED Trainer 2 Slide and release the MASTER POWER switch to provide power to the Trainer. 3 Check to confirm that the existing setup configuration is appropriate for the training scenario. If not, change the setup configuration as desired (refer to Section 3, beginning on page 15 for setup information).
PAGE 24
Using the LIFEPAK CR–T AED Trainer Note: Ensure that the trainee does not touch the adhesive on the QUIK-PAK training electrodes or allow a training electrode to fold over on itself. Also ensure that the training electrodes are correctly oriented on the manikin as shown on the electrode packet (see Figure 8).
PAGE 25
3 SETUP This section provides setup configuration instructions for the LIFEPAK CR–T AED Trainer. It also identifies default settings and describes the setting options, including the procedures for changing those setting options. Setup Configuration and Operating Settings Changing Options for Operating Settings page 16 18 Setup LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 26
Setup SETUP CONFIGURATION AND OPERATING SETTINGS Table 7 lists the operating settings for the LIFEPAK CR-T AED Trainer setup configuration, describes the options for each setting, and identifies the preset default for each setting. Your defibrillator may not have all of the functions identified in Table 7.
PAGE 27
Setup Table 7 Trainer Operating Setting Options (Continued) Operating Settings Options/Description AUTOMATIC/ SEMIAUTOMATIC MODEL The Trainer can be set up to simulate a defibrillator, automatic model (no SHOCK button) or semiautomatic model (SHOCK button). • Automatic The Trainer automatically delivers a simulated shock. The shock button cover is stored in the storage compartment (refer to pages 3 and 4).
PAGE 28
Setup CHANGING OPTIONS FOR OPERATING SETTINGS The following paragraphs describe how to change the operating settings identified in Table 7. Included are paragraphs that discuss using the remote control and LED display when making changes and paragraphs that explain the procedural steps for completing the changes. Using the Remote Control and the LED Display To make changes to the operating settings, you must use the remote control (shown previously in Figure 5, page 7) and the Trainer LED display.
PAGE 29
Setup Table 8 Shock Protocol Options Button Shock Protocol Order F1 Fixed #1 SNNN LED Display* 1 2 3 4 5 6 7 8 9 0 F2 Fixed #2 SSNN 1 2 3 4 5 6 7 8 9 0 F3 Fixed #3 NSNN 1 2 3 4 5 6 7 8 9 0 F4 Fixed #4 NNNN 1 2 3 4 5 6 7 8 9 0 C1 Custom #1 SSSSSSSSS 1 2 3 4 5 6 7 8 9 0 C2 Custom #2 NNNNNNNNN 1 2 3 4 5 6 7 8 9 0 * = Shock (Green) = No Shock (Red) = End Scenario (Blank) Configuring Shock Protocols You can change the Custom #1 and Custom #2 shock protocols to any configuration of SH
PAGE 30
Setup General Operating Settings The procedure for changing the general operating settings (Start Prompt, Stack Shocks, Pulse Check, Pulse Prompts, and Automatic/Semiautomatic Model) is the same for each. Table 9 identifies each general operating setting, indicates the LED bar that corresponds to the setting, and describes the options available.
PAGE 31
Setup CPR Time To change CPR Time 1 or CPR Time 2: 1 Press the RED SELECT button. 2 Press the NO SHOCK ADVISED button (T1) for CPR Time 1 and then proceed with steps 3 and 4. –or– Press the ATTENTION button (T2) for CPR Time 2 and then proceed with steps 3 and 4. 3 Press the RIGHT X ARROW button to advance through the possible CPR time intervals. (Each bar illuminates red as you advance to it.
PAGE 32
Setup 4 Press the RED SELECT button to save the selection. The signal sensor flashes, indicating that the selection has been saved. The Trainer enters simulated OFF status. Setup Figure 13 shows an example of a Trainer configured with Group 1, and the desired language is Finnish.
PAGE 33
Caring for the LIFEPAK CR–T AED Trainer 4 CARING FOR THE LIFEPAK CR–T AED TRAINER This section provides information about caring for the LIFEPAK CR–T AED Trainer. Replacing Batteries Troubleshooting Cleaning Product Recycling Information Warranty Accessories Specifications LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 34
Caring for the LIFEPAK CR–T AED Trainer REPLACING BATTERIES When batteries for the LIFEPAK CR–T AED Trainer or the remote control become depleted or damaged, they should be replaced immediately. Refer to Section 1, page 8 for procedures detailing the steps for installing and replacing batteries in the Trainer and the remote control. TROUBLESHOOTING Tables 11 through 15 provide checklists for troubleshooting LIFEPAK CR–T AED Trainer operating problems.
PAGE 35
Caring for the LIFEPAK CR–T AED Trainer Observation Possible Cause Corrective Action Voice prompts are out of sequence • Incorrect operating setting options selected • Review setup procedures in Section 3, beginning on page 15. Voice prompts are incomplete • Trainer damaged • Contact your local Medtronic representative.
PAGE 36
Caring for the LIFEPAK CR–T AED Trainer CLEANING Clean the Trainer, remote control, and the remote control cable by wiping surfaces with one of the following: • • A lint-free, slightly damp cloth moistened with mild soap and water. A lint-free, slightly damp cloth moistened with denatured alcohol. Observe the following precautions when cleaning: • • • Do not immerse or soak the Trainer, remote control, or the cable. Do not use bleach, bleach dilution, or phenolic compounds.
PAGE 37
Caring for the LIFEPAK CR–T AED Trainer Caring for the LIFEPAK CR–T AED Trainer ACCESSORIES The following accessories are available for the LIFEPAK CR–T AED Trainer: Table 16 LIFEPAK CR–T AED Trainer Accessories Accessory Part Number QUIK-PAK Training Electrode Packet 3201805 Shock Button Cover 3201801 Remote Control and Cable 3201799 Serial Cable 3206630 CHARGE-PAK Trainer 3201800 Quick Reference Card 3201508 Soft Case 3201803 Soft Case Cards 3201792 International Lid Labels 3201755 S
PAGE 38
Caring for the LIFEPAK CR–T AED Trainer Table 18 Remote Control Specifications Transmission Wireless infrared signal. Range, 3 meters max 82-inch (2-meter) optional cable attachment Size 4.57 cm x 3.38 cm x 1.65 cm (1.8 in. x 1.3 in. x .6 in.) Weight (without batteries) 32 grams (.
PAGE 39
APPENDIX A LIFEPAK CR–T AED TRAINER VOICE PROMPTS AND TONES LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 40
PAGE 41
LIFEPAK CR–T AED Trainer Voice Prompts and Tones Table 19 Voice Prompts and Tones Voice Prompt Tones CALL FOR HELP NOW After the AED Trainer lid opens, two beeping tones sound. If the start option is set to voice prompts, this voice prompt will sound following the beeping tones.
PAGE 42
LIFEPAK CR–T AED Trainer Voice Prompts and Tones Table 19 Voice Prompts and Tones (Continued) Voice Prompt Tones CHECK FOR BREATHING IF NOT BREATHING, PROVIDE CHEST COMPRESSIONS AND RESCUE BREATHS CHECK FOR SIGNS OF CIRCULATION IF NO SIGNS OF CIRCULATION, PROVIDE CHEST COMPRESSIONS AND RESCUE BREATHS CONTINUE CARE 32 LIFEPAK CR–T Trainer Operating Instructions
PAGE 44
PAGE 45
LIFEPAK® CR–T AED TRAINER Quick Start Reference Card Quick Start Setup Procedure 1 Turn on the Trainer using the MASTER POWER switch. 2 Press the GREEN SELECT button on the remote control. 3 Select the desired shock protocol (the default setting is C1) using the buttons referenced in the following table. 4 Press the GREEN SELECT button again to confirm shock protocol. The Trainer enters simulated OFF status. 5 You are now ready to begin a training session.
PAGE 46
LIFEPAK® CR–T AED TRAINER Quick Start Reference Card Button Function Button Function Press to change SHOCK ADVISED to NO SHOCK ADVISED. Function is active only during simulated analysis. Press once to activate the ATTENTION indicator in the readiness display. To clear, press the button again. Press to advance the training electrodes to ON or OFF. Press any time to suspend device operation. Press again to resume operation at point of interruption. Press to advance MOTION DETECTED to ON or OFF.
PAGE 48
PAGE 50
PAGE 51
INDEX A Attention Button 7, 11 Attention Indicator 3 Automatic Defibrillator operating setting 17 Automatic/Semiautomatic Shock 17, 20 LIFEPAK CR–T Trainer Operating Instructions ©2002-2007 Medtronic, Inc.
PAGE 52
Index Electrode Pads Button location 7 Button operation 10 Indicators description 6 F Features inside the AED Trainer 5–6 G General Operating Settings Automatic/Semiautomatic Shock 17, 20 CPR Time 17 Pulse Check 17, 20 Pulse Prompts 16, 20 Shock Protocol 16 Stack Shocks 17, 20 Start Prompt 16, 20 Green Select Button Location 7 Operation 12 H Handle location 3 Handle, carrying 3 I Inside Features 5, 6 Installing and Replacing Batteries 8, 24 Installing and Replacing Remote Control Batteries 8 L Language Opt
PAGE 53
Index Replacing Batteries 24 Resetting Default Settings 22 Right Arrow Button Location 7 Operation 12 S Semiautomatic Defibrillator operating setting 17 Service Button Location 7 Operation 11 Setting CPR Time 21 General Operation 20 Language Option 21 Shock protocol 18 Setup Configuration and Operating Settings 16–17 Setup Options Troubleshooting 25 Shock Button cover placement 13 Button location 6 Custom protocols 19 Fixed protocols 18 Protocol Operation 16, 18–19 Side View of Trainer 4 Speaker location 6
PAGE 54
PAGE 55
PAGE 56
Medtronic, Inc. 11811 Willows Road NE Redmond, WA 98052-2003 USA Telephone: 425.867.4000 Toll Free (USA only): 800.442.1142 Fax: 425.867.4121 Internet: www.medtronic-ers.com Medtronic Europe S.A. Rte. du Molliau 31 Case postale 84 1131 Tolochenaz Switzerland Telephone: 41.21.802.7000 Fax: 41.21.802.7900 MIN 3201838-003 / CAT.