What’s New in DEFINITY® Enterprise Communications Server Release 8.
Copyright 2000, Lucent Technologies All Rights Reserved Printed in U.S.A. Notice Every effort was made to ensure that the information in this book was complete and accurate at the time of printing. However, information is subject to change. Your Responsibility for Your System’s Security Toll fraud is the unauthorized use of your telecommunications system by an unauthorized party, for example, persons other than your company’s employees, agents, subcontractors, or persons working on your company’s behalf.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Contents iii Contents Contents iii New Switch and Adjunct Support 1 About this Document 1 ■ ■ ■ ■ Overview 2 DEFINITY® Enterprise Communications Server Release 8 2 Release 8.1 Feature List 3 Release 8.2 Feature List 5 Platform - Enhancements/Renewal 7 DADMIN LOGIN 7 Optical Drive (TN2211) 8 U.S.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Contents v ■ ■ ■ Networking - ISDN Public 155 BellCore Calling Name ID 155 Bellcore National ISDN Calling Name Supplementary Service for PRI 156 Feature Plus – Non-DID Calling via UDP 160 Multiple Pubnet Calling/Connect Numbers/ System (Italy) 163 Pass Advice of Charge (AOC) to BRI Endpoints 172 Restricted Presentation 179 IP Solutions 186 TCP/IP-Connected Trunks 186 H.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support 1 New Switch and Adjunct Support 1 About this Document This document introduces new and enhanced features and capabilities of DEFINITY Enterprise Communications Server (ECS) Release 8. It does not contain comprehensive instructions for switch administration or complete feature descriptions, nor does it contain information about how to install, maintain, repair, or troubleshoot the switch.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Overview Overview DEFINITY® Enterprise Communications Server Release 8 DEFINITY® ECS Release 8 is the next step in the evolution of the DEFINITY® ECS. ■ It is a multi-purpose platform developed to support a number of offers.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Overview Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Overview China Outgoing Call No Answer China Time Super.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Overview TN799B ■ Variable Length Pin ■ TraceRoute ■ Packet Error History ■ SNMP Re-arch ■ Host Route Admin Chan Cs TN2211 Optical Drive ■ UN332C MSSNET Release 8.2 Feature List IP Solutions ■ IP SoftPhones ■ H.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Platform - Enhancements/Renewal 7 Platform - Enhancements/Renewal DADMIN LOGIN ■ Administration of the dadmin login uses the standard DEFINITY® login and permission form interfaces. ■ Dadmin Login replaces Inads Login for Distributors. ■ The dadmin login ID, restricts access to commands that are limited to Lucent Services.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal 8 Feature to Feature Interactions Access Security Gateway (ASG) ■ ASG authentication not required by default for the dadmin login. ■ ASG field on the dadmin login form defaults to n(o) and all fields that appear on the Access Security Gateway page of the login form are unassigned or set to system defaults.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal ■ The TN2211 Optical Drive resolves several problems related to the tape drive such as availability, cost, performance, reliability, and storage capacity. ■ The TN2211 is designed to be less expensive and more reliable than the TN1656. ■ Installation and Upgrade procedures for the TN2211 optical drive are nearly the same as for the TN1656 tape drive.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal 10 Configuration ■ The configuration is a G3r switch (simplex or duplex) with a TN2211 Optical Drive and a UN332C MSSNET OR a TN1656 Tape Drive and a UN332B MSSNET. ■ All commands using tape are replaced by removable-media. ■ Commands such as test tape, busy tape, release tape, etc. are replaced by removable-media.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal ■ The procedure to both upgrade from pre-R8 to R8 and to change from a TN1656 to a TN2211 at the same time is not supported. ■ Services must upgrade the hardware first (TN1656 to a TN2211 and a UN332B to a UN332C), then upgrade to the R8 software. 11 — The hardware must be upgraded prior to the software.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal 13 Maintenance NOTE: Refer to Definity ECS Release 8.2 Upgrades and Additions for R8r, 555233-115, Issue 1. ■ A TN2211 is maintained in software as if it were a TN1656. ■ After inserting an optical disk cartridge, the access lamp of the drive should be on for a few seconds, then should turn off.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Platform - Enhancements/Renewal 14 U.S. Analog Trunk & Line Circuit Pack TN797 Description This circuit pack is the combination 8-port Analog Trunk and Line Circuit Pack, TN797, for the US, Canada, and like countries.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Platform - Enhancements/Renewal 15 The TN2313 DS1 interface can be configured for domestic (24-channel, 1.544 Mbps) or international (32-channel, 2.048 Mbps) use. The TN2313 can supply two 8-Khz reference signals to the switch backplane for optional use by the tone/clock board in synchronizing the system clock to the received line clock.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 17 Remote SAC Activation/Deactivation Form ■ Added New “Remote Send All Calls Activation:” and “Deactivation:” Fields on the FEATURE ACCESS CODE (FAC) Form — FACs allow a remote user to activate or deactivate the Send All Calls feature. — Feature access codes may be 1 to 4 digits; * and # may be used as the first digit only. The defaults are blank.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 18 ■ The user then dials the station extension number, followed by a “#” and station security code (SSC), followed by a “#.” ■ The Remote SAC Activation/Deactivation feature can also be activated by a local user from any local extension.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 19 Off-Net Coverage Points ■ Any point in a principal’s coverage path can be administered as an off-net destination. NOTE: Time-of-Day Coverage feature increases the number of coverage points from 3 to 6. Increase Number of Remote Coverage Points ■ Number of Remote Coverage Points available (on all platforms) increased from 225 to 999.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 21 NOTE: Application of coverage treatment does not guarantee that the call will definitely redirect to a coverage point, since the coverage criteria as applied at the forwarded-to destination may not be satisfied.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 22 Option to Dispense with Call Classifier On Coverage Call ■ Established a new field, “Maintain SBA At Principal?” ■ This is a y/n field. ■ The default is y, which maintains current operation. ■ When a customer is upgraded from a release prior to R8, this field is set to y.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 24 — The new form displays a maximum of 48 codes (3 columns), leaving only 1 column for adding more codes. — To enter more codes, execute change authorization - code 9999999.... to show a blank screen, allowing 64 codes to be submitted at one time rather than the original 96.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 25 Auto Exclusion ■ When Privacy - Manual Exclusion is activated, all other users with appearances of an extension are prevented from bridging onto the active call. — If the Exclusion button is pressed while other users are bridged onto the call, the other users are dropped from the call.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global ■ 26 Allows a user to activate automatically Exclusion when they go off hook on a station that has an assigned EXCLUSION button. If set to n, allows a user manual exclusion when they press the EXCLUSION button before dialing or during a call. Appears when, on the Feature-Related System Parameters screen, the Automatic Exclusion by COS field is y.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global ■ 27 Recall Rotary Digit This establishes the digit to use for rotary phones to receive recall dial tone. Dialing this digit simulates switch hook flash so that users of rotary phones can use features such as conference and transfer. The phone must also be administered to use the recall rotary digit.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 28 Group Call Pick-up ■ Work groups in Japan use this feature. ■ Allows users to dial a FAC and then a pickup group number, in order to answer a call pickup call from a different call pickup group.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global ■ 31 HELP values for the Type field include CallrID. NOTE: CallrID is one word, limited to seven characters by Type field constraints. ■ The fields Display Caller ID? y and Caller ID Message Waiting Indication? n appear in this form only when CallrID is chosen as the terminal Type.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global NOTE: Caller ID feature requires the TN793B or TN2793B circuit pack. Figure 2.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global Figure 3. 33 6220 Analog Telephone Description of the terminals(continued) ■ ■ The 6200 family of analog terminals requires DEFINITY® ECS R8 software. If R8.1 is used as a bugfix, access to the CallrID terminal type is blocked. — Access is not blocked for the 6200 family of terminals.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 34 NOTE: Many Caller ID protocols specify FSK signaling for MWI. 6400 Tip/Ring (Data Module Features) ■ The 6400 Tip/Ring feature supports the operation of an analog adjunct operating independently on an I2 channel with its own extension for 64xx DCP telephones.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global Figure 4.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global Figure 5. 36 6424D+ DCP Terminal Administration The 6416D+ and the 6424D+ terminals are administered with a data option field for an analog adjunct. ■ Administer as a data module field on add station form. ■ An option on the add station form allows users to administer their own particular extension.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 43 Support for 24-button expansion modules The XM24 expansion module is fully functional when administered together with the 6416D+ and 6424D+ voice terminals.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 44 NOTE: The Abort Transfer / Abort Conference features are not applicable to Attendant Consoles. Administration Enable Abort Transfer Operation and Enable Abort Conference Operation ■ Enabled/disabled on a per-system basis by the use of 2 new fields on the system-parameters features form. ■ Automatically disabled on upgrades.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 45 — Default: n — Error: invalid entry, press help. Attendant Vectoring Attendant Call Vectoring is a stand alone feature that is supported on a single switch environment with or without CAS.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 46 Attendant Group Calls Attendant group calls are calls directed to an attendant group; calls to an individual attendant (via the assigned extension) are not considered attendant group calls.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 47 attendant group other than 1 is denied. All endpoints in the system are defaulted to TN 1 which by default belongs to attendant group 1. Any attempt to assign TN numbers other than 1 is also denied. So, attendant group calls will always terminate to attendant group 1.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 48 attendant group as they currently do. How Definity determines which party’s TN to use in call scenarios will remain unchanged by attendant vectoring. The VDN for the selected TN will apply. For example, the selected TN for calls covered to an attendant group, is the called user’s, not the calling user’s, TN.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global ■ wait-time secs hearing then ■ stop 49 If attendant vectoring results in putting a call in the attendant queue, it will be placed in queue with the priority as administered on the console parameter form. There will be no changes made to the attendant priority queue for attendant vectoring.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 50 redirected to attendant vectoring when the system is in night service unless a night console is available. Otherwise, they will continue to be redirected to the applicable night service processing.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 51 ■ Emergency access redirection - An attendant VDN can be assigned to emergency access redirection. When the attendant’s emergency queue over-flows or when the attendant group is in night service, all emergency calls will be redirected to this VDN. Careful thought should be given to routing these calls off-switch.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 52 Administration is as follows: a. All stations are assigned TN 1 which is associated with attendant group 1, VDN 1999, and music source 1 b. All trunk groups are assigned TN 2 which is associated with attendant group 1, VDN 2999, and music source 2 c. All VDNs are assigned TN 3 which is associated with attendant group 2, VDN 3999, and music source 3 d.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 53 unanswered after 999 seconds in the hunt group queue, the caller hears busy and vector processing terminates. If the call cannot be queued, the call will be routed to the remote location and vector processing will terminate. NOTE: The main difference from scenario 1 is queueing the call to the hunt group rather than routing the call there.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global Table 4. 54 QSIG CAS Vector VDN 1000 vector 1 1. announcement 9000 2. route-to number 93035380 with cov y if unconditionally CAS MAIN Calls from a QSIG branch are sent to the main with the main’s attendant access code as the destination address so these calls are automatically attendant group calls.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 55 cover on station 6000’s coverage path. Vector processing will continue and route the call to a remote location. NOTE: When station night service is active, calls are processed according to the administered night destination for the trunk group, not the night destination for the associated TN (i.e., these are not attendant group calls).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 56 2. Execute the display events command from the command line. Search for CATEGORYCATEGORY denial. 3. Search the EVENTS REPORT for the hexidecimal cid to troubleshoot the problem. Diagnostic Example: list trace to Diagnose Intercept Tone (Denial) In this example, the customer heard an intercept tone (denial of service).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 57 Diagnostic Example: list trace to Diagnose Fast Busy (Reorder Tone) In this example, no trunks were available in trunk group 1.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 58 Diagnostic Example: list trace to Diagnose DID not Ringing Correctly In this example, the trace verifies the inbound digits from the network and traces DID trunk to VDN 52099, to vector 1, terminated to agent 51001.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support General Telephony Enhancements - Global 59 Diagnostic Example: list trace to Diagnose Station not Ringing In this example, the trace verifies the inbound DID call to x52001 is forwarded offnet and the trunk hung up.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global 60 Diagnostic Example: list trace to Analyze Trunk Signaling Failure In this example, the trunk wink was not received from the network. Notice there is no trunk seizure message and digits are not outpulsed. Check the hardware error log for trunk group 2 errors indicating seizure failure.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support General Telephony Enhancements - Global Diagnostic Example: list trace to Display ISDN Call Completion In this example, the outbound ISDN call is completed. Note the ISDN ALERTING message was received followed by an active trunk message indicating the called party answered.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features 62 NewHospitality-Related Features Auto Selection Direct Inward Dial (DID) Numbers ■ Provides the capability to have the system automatically choose a number among a list of available DID numbers to be assigned to a guest’s room upon check-in. ■ Useful for any hotel wishing to have direct dialing to rooms without attendant intervention.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features 63 From inside the hotel, either the room/extension number or the 2- to 5-digit DID number may be used. ■ NOTE: XDIDs that are unused will follow the coverage path. All xdids cover to voice mail so that they can get a recording that says nobody is checked in. Administration Coverage ■ XDID ports perform the Hunt-to function before coverage.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support NewHospitality-Related Features 64 ■ Use will only be allowed on a station with console permissions. ■ The DID can continue to be changed as long as y is pressed.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features 65 Call Processing ■ PMS can request a DID assignment from the switch in the check-in message. ■ When the Automatic DID assignment feature is active and check-ins are done from the PMS, the system assigns all check-ins received from the PMS a DID number from the list of XDID numbers. — The number is chosen from the list in a FIFO manner.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features 66 If a crisis alert call is originated in an emergency situation, a message will be sent to a pager to notify the page of the extension and location where the emergency call was originated.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features 67 ■ When the Alert Pager field is turned on new fields appear, Originating Extension, Crisis Alert Code, Retries, Retry Interval, Main Number, three pager numbers and three pin numbers. ■ The Originating Extension field requires a valid extension to be entered for use as the extension originating the call to send a crisis alert message to a pager.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support NewHospitality-Related Features ■ 70 Result of attempt to pager sent to journal printer. — The journal printer prints out the result, successful or unsuccessful, of the final attempt of sending a message to the pager. — Each pager number has status sent to the journal printer. Hardware ■ Digital Numeric Pager ■ TN2182 - Tone Board/Call Classifier or TN744B, C.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support NewHospitality-Related Features 71 ■ For a group of stations to appear as a suite, the primary extension (the extension that the PMS will be passing to the switch in the check-in message) must have the secondary extension administered in its hunt-to field on the station form.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 73 New Mobility-Related Features X-Station Mobility (DECT) ■ X-Station Mobility Feature allows phones remoted over a trunk interface to be controlled by DEFINITY® as if they were directly connected to it. ■ Accomplished by administering a station record for each station to be so controlled as of type X-mobile.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support New Mobility-Related Features 75 Terminal Type ■ Setting the type in the station screen to XMOBILE will identify an X-mobile station. Signaling Group administration ■ New field X-Mobility/Wireless Type is added to the signaling group form to indicate the type of X-mobile endpoints allowed for it (DECT or NONE). ■ The default for the field is NONE.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features ■ 76 When a call comes in from a trunk group marked as having X-mobile endpoints, the SETUP message is checked for a CALLING PARTY NUMBER Information Element. — If present, and if it matches the extension of a station marked as Xmobile, that call is re-stimulated as an internal call originating from the X-mobile station.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 77 Scenarios ■ All feature operations are intended to work exactly as if the X-mobile station were directly connected to the DEFINITY® System. ■ Analog type feature operation were chosen, since most wireless terminals support only flash operations and are not multi-appearance or context sensitive.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 78 NOTE: If the X-Mobile trunk does not return alerting, and instead returns a disconnect or release, the DEFINITY® system software advances to the next coverage point, if administered. If the next coverage point is not administered, DEFINITY® system software disconnects ringback tone and present busy tone.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support New Mobility-Related Features ■ 79 This customer option is disabled by default for new R8 systems and for older systems that upgrade to R8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support New Mobility-Related Features 80 Station form indicates MWI update type ■ The Message Waiting Type field on the station form indicates the mode of MWI update to the WT. ■ The MWI activation/deactivation message is used when the field is set to ICON. ■ The MW is attached to the end of the display line during an incoming or outgoing call if the field is set to DISP.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 81 ■ If the administered software version is V5 or earlier this feature cannot be enabled. ■ The only form that includes new fields is the signaling group form. The new field is defaulted to none on upgrades. ■ The feature must be enabled from the customer options screen.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 82 Flash Operation ■ If an INFO message containing a KeyPad Facility Information Element of the value 0x15 or values 0x1B, 0x48, the message is interpreted as a Flash-hook operation from the remote station. NOTE: These values are defined by the ETSI DECT GAP standard and the RCR-28 PHS standard.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 83 Display ■ When an X-Mobile station is ringing or active, an ISDN Info message is used to update its display whenever appropriate. ■ The display for an X-Mobile station is limited compared with standard DEFINITY® system displays. ■ The length is limited to 15 characters.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 84 Calling Party Name ■ The X-Mobile station sends the calling party name information in a DISPLAY Information Element whenever normal call processing for that station would update the display of the station to indicate the calling party.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 85 Call Progress Tones to Remote Party ■ ■ When a party dials to an X-Mobile station, the DEFINITY® system provides ring-back, busy, or re-order tone as appropriate. If the remote party is put on hold by the X-Mobile station, hold tone or music on hold is provided as administered for the system.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 86 Display-based Message Waiting Indication ■ All text information sent to an X-Mobile station contains information indicating a message is waiting for it, if the station is marked as having a message waiting. ■ Noted by an MW at the end of the display line. ■ Content of the string is administerable.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 87 Process Idle X-Mobile WT’s switch-hook icon flashes when message is waiting ■ When a message is left for an X-Mobile Station either through a messaging adjunct (for example, INTUITY™ AUDIX®) or one of the DEFINITY® system-based features (for example, Leave Word Calling), the X-Mobile WT’s message status indication is updated immediately.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features ■ It will not flash the switch-hook icon after the station goes onhook. ■ MWI operation follows ASN.1 specification in ETS 300 745-1. ■ MWI Activation/Deactivation messages are conveyed through FACILITY messages. ■ 88 The DEFINITY® system sends the MWI Activation/Deactivation messages in a connectionless mode through the ISDN FACILITY messages.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 89 ■ The display is the same as a standard analog station with one exception. ■ When the station is onhook, the port field is blank. ■ When the station is offhook the port field contains the identity of the connected ISDN trunk port.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support New Mobility-Related Features 90 Scenarios ■ All feature operations are intended to work exactly as if the X-Mobile station were directly connected to the DEFINITY® system. ■ Analog-type feature operation was chosen, since most wireless terminals support only flash operations and are not multiappearance or context sensitive.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Telephony Applications - International 91 Telephony Applications - International Reset Shift Call When a station call is made to a busy station, reset shift dial tone, called second dial tone by the Japanese PBX manufacturers, is heard.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Telephony Applications - International 92 This feature applies to all hardware platforms. NOTE: Since Japan does not have regulations on the characteristics for reset shift dial tone, users require training to properly identify the tone that DEFINITY® ECS uses for this feature.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Telephony Applications - International 93 Administration Initial Administration To administer the reset shift call feature on a DEFINITY® system where it was not previously used, the following procedure should be utilized: 1. In order to fully use the reset shift call feature, station extensions should be assigned with contiguous numbers for groups of users.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Telephony Applications - International 95 Terminals This feature applies to all sets with the following exception: multi-function analog terminal (MFAT) sets can not receive reset shift dial tone, although they can be the targets of a reset shift call from another terminal type.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center ■ 97 CMS High Availability — Dual CMS systems — Manual alarm clears — Historical log — Non-disruptive cmsadm backups — Reasonable restores — Non-disruptive maintenance backups — External Call History alarms ■ R3V8 CMS not a bug fix for R3V6 ■ R3V8 CMS does not support G2.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Call Center 98 Call Center Design Graphic • High Availability (dual CMS CentreVu CMS R3V8 links, etc.) • ATM Support • Advocate Enhancements Support • Database Corruption Mitigation • Workforce Management Support • ASCII Agent Admin DECS DEFINITY ECS R8.1 CMS-PBX X.25 SPI ODBC JDBC CORBA CVS Msgs.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 99 Call Center - ASAI Trunk Group Identification ■ Provides the application with the capability to obtain Trunk Group information regardless of whether Calling Party Number is reported.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 100 Call Center – ASAI/CTI Pending Work Mode Changes ■ This feature provides ASAI applications with the capability to change the current work mode of an agent while the agent is busy on a call by making it a pending change, which takes effect as soon as all current calls are cleared. ■ Previously, ASAI did not allow an application to change the work mode of an agent.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 101 Cross-Product Compatibility/Commonality Terminals ■ If there are feature buttons on an agent’s phone for AUX, AI, MI and ACW work modes and an ASAI Change of Work Mode request is received by DEFINITY® for an agent with active calls, the lamp for the current work mode button will stay lit while the lamp for the pending work mode will flash.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 New Switch and Adjunct Support Call Center 1 103 Display Internal Data Hunt Group Command ■ Updated for capacity increases for split/skill domain control.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 104 Call Center-Logged in Advocate Agent Counting ■ Modified in the CentreVu Advocate R 8.1 DEFINITY. ■ The “Logged-In Advocate Agents” customer option that was added in DEFINITY R7.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Call Center 105 ■ The advantage to a call center of using ATM trunks is that this type of trunk can be a cheaper alternative to the existing T1/E1 option. ■ ATM WAN PNC provides the ability to interconnect port networks using an Asynchronous Transfer Mode (ATM) wide-area network (WAN).
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center ■ The changes to support ATM Trunk Measurements make R3V8 CMS incompatible with G2.2 and G3V1. ■ R3V8 CMS is backward compatible with G3V2 onward. ■ R3V8 can not be a bug-fix load for R3V6 due to the Solaris Operating System upgrade.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center ■ 107 ATM trunks are supported through new circuit packs that use a different equipment location format than trunks currently supported by CMS — ATM trunks require a circuit number of 3 digits to be supported (up from 2 digits). — CMS supports a revised trunk equipment location number with the expanded circuit number.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 109 CMS High Availability CMS High Availability applies to all standard R3V8 CMS platforms (SPARC 5, SPARC 20, Ultra 5, Ultra Enterprise 3000, and Ultra Enterprise 3500), and provides for the following: ■ Non-disruptive cmsadm backup. — Ability to perform a cmsadm backup with data collection turned on during the entire cmsadm backup process. ■ Non-disruptive maintenance backup.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 New Switch and Adjunct Support Call Center 110 CMS High Availability Configuration Terminal CMS server (primary) CentreVu CMS Supplemental Services CentreVu Visual Vectors (if purchased) CentreVu Internet Solutions (if purchased) NTS (dedicated to primary CMS) Printer Modem DEFINITY R8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 1 Issue 1 April 2000 New Switch and Adjunct Support Call Center 111 Reliability ■ The CMS data collection process is improved by duplicating the ACD links. ■ The customer only loses ACD data associated with an ACD link failure under these circumstances: — ACD software failure — Simultaneous C-LAN card failures — Simultaneous network failures across both ACD links — Combinations of failures on both ACD links.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International Networking Enhancements 113 2 2 Networking - International Continuous and Pulsed E&M Signaling (Brazil) This feature provides the user with the capability to make and receive calls over Brazil pulsed or continuous E&M signaling trunks and to administer the signaling bit on all CAS DS1 trunk types. Also addressed is Hungarian pulsed E&M.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 114 Feature Administration To administer this feature for use in Brazil, one administers the forms for DS1 Circuit pack and Trunk Group. In particular, the fields shown in bold print in those sections should have one of the values listed. This feature provides only trunk line signaling; and in Brazil the COs that use these protocols expect R2-MFC line signaling.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - International 115 Seize when maintenance busy per network trunk group This requirement is administrable per public network trunk group, and applies to trunk group type DIOD. The administration is via the existing field called Seize When Maintenance Busy being ported from the tie trunk screen to the above trunk group type screen. Administration steps 1. Administer the basic system. 2.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International ■ Normal Outgoing Seize send (ms): 150 (10 - 990). ■ Outgoing Disconnect Send (ms): 600 (100 - 9900). ■ Outgoing Last Digit (sec): 40 (10 - 40). ■ Outgoing Seizure Response (sec): 255 (1 - 255). ■ Release Ack Send (ms): 600 (500 - 1200). ■ Seize Ack Delay (ms): 120 (40 - 120). ■ Seize Ack send (ms): 150 (10 - 990).
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 119 Capacity Constraints and Feature Limitations This feature does not cover outgoing calls that are automatically generated by the switch and have no human involved in the call. Examples of such calls include outgoing alarm calls from the INADS port, and transmission test calls from the ATMS feature.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - International 120 For such trunks, many sites use the answer supervision timeout, which is not useful with the Disconnect on No Answer feature. If an administrator were to simply disable the timeout, then the call will drop during the speech phase. 1. Administer answer supervision by classifier. The field used for that is receive answer supervision on the trunk group form 1.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 121 Time Supervision & Force Release (China) Time Supervision & Force Release (China) provides three no-answer limits based on call type only for calls in which digits are analyzed by ARS. Outgoing trunk calls that are not analyzed by digit analysis have a fixed no-answer time limit of 120 seconds.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 122 Alternate treatment for offhook after a call If the switch is administered and any station set is the last party remaining offhook on a call, the switch will play tones to offhook sets if the calling set is not an analog set.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 123 Other ARS call types Howler After Busy If the Station Tone Forward Disconnect field on the Feature Related System Parameters form is set to anything other than busy, the user receives the treatment specified by that field instead of busy tone followed by howler tone.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - International 130 Field descriptions for page 2 Digital Loss Plan Provides the default values for digital loss plan and n-party conference loss. Valid entries Usage 1 - 25 Refer to the Country code table at the beginning of this screen description. Customize Appears when the Digital Loss Plan Modification field is enabled on the SystemParameters Customer-Options screen.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - International 131 Field descriptions for page 3 Digital Tone Plan Provides the default values for tone loss for the selected country. Valid entries Usage 1 - 25 Refer to the Country code table at the beginning of this screen description. Customize Appears when, on the System-Parameters Customer-Options screen, the Digital Loss Plan Modification field is y.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - International 132 Other Gain/Loss Factors The following table shows existing fields that also affect loss through a switch: Form Field Loss or gain is applied: system-parameters multifrequency-signaling Received Signal Gain (-Loss) (dB) Between the tone receiver and the trunk port during MFC tone reception.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 133 Networking - ISDN Private QSIG Call Independent Signaling Connection (CISC) Enhancements ■ Provides the user with the capability to transport QSIG operation information independent of an active call, between two QSIG compliant nodes.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private 135 ■ If pages 2 through 5 are administered and the "Supplementary Service Protocol:" is changed from "a" to "b", there is a warning message that those pages are blanked when the form is submitted. ■ If a signaling group’s "Supplementary Service Protocol:" is set to "b", the ISDN TSC Gateway form is checked.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private ■ ■ 137 The encoding allows QSIG-VALU features to work between DEFINITY® systems in a QSIG network, even if the connection between the DEFINITY® systems includes non-DEFINITY® systems. QSIG-VALU Call Coverage feature extends the Call Coverage feature transparency when a coverage point is located on a remote DEFINITY® system connected via a QSIG network.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 138 Distinctive Ringing Administration 1. Option Value-Added Lucent (VALU) is Enabled on System-parameters customer-options form 2.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 140 QSIG-VALU Coverage Administration 1. Option Value-Added Lucent (VALU) is Enabled on System-parameters customer-options form 2.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private Issue 1 April 2000 141 QSIG Integration: Transfer to Audix This feature provides the user with the capability to transfer directly into the voice mail box of a subscriber on the voice mail system when DEFINITY and the voice mail are connected via a QSIG link. QSIG Transfer Into QSIG Voice Mail is not a feature defined by QSIG standards, so MSI is needed to accomplish the desired functionality.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 142 cases where a secretary is a coverage point for a boss. Suppose the secretary answers a call which has covered from the boss. If the calling party would like to leave a message for the boss, then the secretary can activate Transfer Into Voice Mail and the calling party will be transferred into the boss’s mailbox.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private ■ 143 A hunt group must be in the coverage path of the user ‘s mailbox to be transferred into, as administered on the station and coverage path forms. For this hunt group, the hunt group form must have “qsig-mwi” for field “Message Center:” and number of the voice mail system must be administered in field “Voice Mail Number”.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 144 Access Code”. There will be no changes to the existing use of the field and no additional admin checking will be done. The only change is to the name of the field.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private DEFINITY DEFINITY PBX A Calling Party Figure 9. 145 QSIG PBX B TRANSIT QSIG-VALU DEFINITY TRANSIT QSIG QSIG-VALU Principal (Called Party) PBX C Coverage Point (Redirected-to Party Basic QSIG-VALU Call Coverage Scenario QSIG-VALU Call Coverage will enhance the operations for the users, similar to DCS Call Coverage, in the following ways: 1.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 146 5. Principal user will be able to bridge on to the call while the call is routed to QSIG-VALU coverage points and after the call is answered by the coverage point. 6.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 148 Display Enhancements Release Link Trunks (RLT) are limited in the amount of information that can be passed and displayed to the attendant. CAS Display Enhancements are possible by replacing RLT with QSIG ISDN trunks. Display enhancements are achieved by using QSIG MSI messages.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 149 NOTE: DEFINITY One and Guestworks are not supported. Voice mail systems that support these connections are: ■ Intuity AUDIX R4.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private Legend 150 Voice Mail Legend DEFINITY Legend DEFINITY Voice Mail Figure 10.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private 151 Setting Up Centralized Voice Mail Via Mode Code The following step describe how to set up DEFINITY switches to support centralized voice mail. For information on setting up Merlin Legend/Merlin Magix, see Merlin Magix Integrated Systems Network Reference, 555-715-114.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 152 — Send Name field is y. — Send Calling Number field is y. — Numbering Format field is Private. — Send Connected Number field is y. 6. On each remote switch, repeat steps 3-5. 7. On each DEFINITY switch in the network, enter change dialplan on the command line of your system administration screen. 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Private 153 14. For each DEFINITY node, enter change isdn private-numbering, and verify fields as follows: 15. Set Network Level field is 0 This setting overrides the signaling on the D channel, allowing the Message Waiting lamp activation signal to be sent 16. On the DEFINITY node, enter change sys params mode-code on the command line. 17.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Private 154 — Distinctive Audible Alert field is n. — Switchhook Flash field is y. — LWC Activation field is y. 24. For each remote DEFINITY node, enter change coverage remote on the command line. 25. Administer or verify the following: — 01 contains the extension of the voice mail hunt group.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public 155 Networking - ISDN Public BellCore Calling Name ID Bellcore Format with V.23 FSK ■ The 24-Port Analog Line with CID feature supports the option to send Bellcore specification messages using V.23 modem protocol. ■ Bellcore Format with V.23 FSK differs from the standard Bellcore format only in the frequencies used for the FSK signaling in the Physical Layer.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 156 US NI Calling Name for Outgoing Calls? Valid entries Usage y/n Enter y to send a name on outgoing calls over NI PRI trunks. Important: Be sure you have validated that your service provider’s central office is capable of accepting calling name information from DEFINITY in this way. For example, if the central office switch is a 5ESS, it must be a generic 5EXX or later.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 157 Capacity Constraints and Feature Limitations ■ DEFINITY will be capable of receiving up to 50 characters of Bellcore National ISDN Calling Name information but display a maximum of 15 characters. — Truncation behaviors will truncate names longer than 15 characters to the first 15 characters to be displayed.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 158 The 5ESS network database query timer is set to one to six seconds (three seconds is the default). — The aim of DEFINITY support of the Bellcore Calling Name is to present as similar a user interface as the LEC Caller-ID service. Caller-ID usually delivers the Caller ID information on the 2nd ring cycle with each ring-silence cycle defined as 6 seconds.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public 159 SS Option A Choices ■ The “Send Name:” field on page 2 of ISDN Trunk Group form allows the “r”(estricted) choice when the “Supplementary Service Protocol” is set to “A” (National SS protocol). Standard error and help messages apply. Trunk Group Page 2 screen with the new field choice and new field.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 160 With the addition of Bellcore National ISDN Calling Name feature, interworking of Calling Name in the Bellcore National ISDN network will also be fully supported if the Bellcore Calling Name information is available in the SETUP message.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 161 ■ When a LDN call is received, the incoming SETUP message is checked for a Calling Party Subaddress IE containing a DID extension. ■ If the extension is present, the call will not be sent to the attendant, as is currently the case. The call will, instead, be routed to the indicated extension.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public 162 Route Pattern Form Page 1 of 3 change route-pattern 1 Pattern Number: 1 0 Grp. FRL NPA Pfx No. Mrk _ ___ _ __ __ __ _ ___ _ __ __ __ _ ___ _ __ __ __ _ ___ _ __ __ __ _ ___ _ __ __ __ _ ___ _ __ __ __ Hop Toll No.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 163 Alerting Ring Pattern ■ If the incoming trunk group, which terminates to the LDN, is administered as tie, the ring pattern administered on the trunk for incoming calls apply. — If Internal Alert? is yes, the system ring pattern administered for internal calls apply. — If Internal Alert? is no, the system ring pattern for external calls apply.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 164 ■ Public networks may check the accuracy of the Calling Line Identification number information sent by a CPE. ■ The number is checked to make sure it is within a provisioned range. ■ If the number is not accurate based on the trunk group used, the DEFINITY®-provided Calling Number would be deleted and a networkprovided “main billing” number would be used instead.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 165 Configuration/Environment ■ These enhancements are available regardless of the administered software version on a DEFINITY® switch.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 166 ISDN – DCS over ISDN PRI D-Channel (DCS+) DCS+ may be administered to display the ISDN Connected number information, which will be subject to the prefixing enhancement. ■ Adjunct Switch Applications Interface (ASAI) ■ For many customers over the ASAI interface, the received Calling/ Connected Party Number IE will be sent, without any International/National prefix.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 167 ■ The default for these fields are blank, to be interpreted that no national or international prefix is appended to identification numbers displayed. ■ Valid entries for these fields include any digit 0-9, *, and #. ■ Any digit or * or # may be entered in any position within the prefix and may be repeated within the prefix.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 168 Stations 2000 to 2999 can send Calling Number information when using the 24 bidirectional trunk groupsnumbered 2-25; stations 2000 to 2999 can send Connected/QSIG-VALU Called/QSIG-VALU Busy Number information when using the 29 incoming-only trunk groups numbered 2654.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 169 Administer entries in the isdn public-unknown- numbering form — For each Ext Len/Ext Code combination desired, one entry may be entered with 11 as the Trk Grp(s) value, another entry may be entered with 22 as the Trk Grp(s) value. — Enter the appropriate CPN Prefix and Total CPN Length values for each entry.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 170 Originating QSIG-VALU Called/Busy Number based on Trunk Group Numbers — For ISDN calls, if a specific QSIG-VALU Number (Called/Busy) is originated by the DEFINITY® system using the ISDN NumberPublic/Unknown table to determine the number sent is enhanced to check the Trk Grp(s) field.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 171 Network provided AOC is tandemed to WCBRI regardless of the administered WCBRI country protocol. NOTE: If the far end hangs up on a call, AOC may be passed to WCBR. If the local WCBRI endpoint hangs up first, any AOC received from the network side will not be passed to the WCBRI endpoint if a WCBRI endpoint is administered for “1-step clearing” procedures.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 172 When there is a dial-out Meet-Me Conference, the DEFINITY® system generates an event report and needs to determine the Calling Number information for the call by using the isdn public-unknown form without knowing what trunk group the call is carried.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public ■ 173 Administer the Pass Prefixed CPN to ASAI? field to y if desiring the nondefault value, then any Calling Number for inbound calls passed to ASAI will include prefix if the call should get prefix treatment, or any Connected Number for outbound calls passed to ASAI will include prefix if the call should get prefix treatment.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public 174 ■ ACD agents extensions range from 2000 to 2999 and these extensions can receive incoming calls only and are not allowed to make external calls. There are no isdn public-unknown numbering form entries for these extensions. ■ There are 59 ISDN PRI trunk groups.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public Issue 1 April 2000 175 Multiple Public Numbering ■ Select an ISDN networking option on the system-parameters customeroptions form: either ISDN or ISDN-BRI Trunks. ■ Administer two or more ISDN-type trunk groups with trunk group number 11 and 22.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 176 Originating QSIG-VALU Called/Busy Number based on Trunk Group Numbers ■ ■ Any prefixed Calling/Connected/QSIG-VALU Called/QSIG-VALU Busy number that’s longer than 15 digits is truncated from the least significant digits according to the current DEFINITY® system behavior.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 177 Advice of Charge ■ The WCBRI Platform supports the line-side country protocols of Bellcore National ISDN-1, Australia, ETSI, Japan, and Singapore. ■ Network provided AOC is tandemed to WCBRI regardless of the administered WCBRI country protocol. ■ Bellcore National ISDN and Singapore networks are not known to support AOC services.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 178 Transmission Interface ■ The ISDN enhancements only affect D-channel information signaling and end-user displays. ■ No impact on the B-Channel connection used for each call. ■ The IEs include Codeset 0 Facility IE (ETSI), Codeset 0 Display IE (Australia), Codeset 6 (CEPT Italy) Charging Information IE, and Codeset 6 AOC IE (Japan).
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 179 Message Sequence Tracer (MST) ■ The MST records the CPNs and other identification numbers as received on the link. ■ The MST is enhanced to record new message types and IEs containing AOC information tandemed over WCBRI signaling links.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 181 ■ If no Calling/Connected, QSIG-VALU Called and/or QSIG-VALU Busy numbered Number IE is received at all, the same trunk group administration determines whether a replacement string is used as the number field in a display. ■ Allows a special character to be appended to Restricted Calling numbers sent over the ASAI link.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ISDN Public 182 Administration System Parameters Special-applications Form ■ If the release version on the Customer Option form is “R8” or later, the field “ISDN Presentation Restriction?” field is removed from the systemparameters special-applications form.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ISDN Public 183 System Parameters Features Form ■ Two administrable text fields on page 6 under the ISDN parameters title. ■ Fields titled “CPN Replacement for Restricted Calls” and “CPN Replacement for Unavailable Calls”.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 186 IP Solutions DEFINITY ECS IP Solutions provide TCP/IP connectivity for two types of trunks and three types of IP Softphones. On DEFINITY ECS, IP Solutions use the TN802B IP Interface assembly, which includes a Windows NT server that resides on the TN802B circuit pack inside the DEFINITY ECS.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions 187 vendors’ H.323 v2-compliant switches, or as direct-inward-dial (DID) type of “public” trunk providing access to the switch for unregistered users. A variety of signaling options can be chosen by the system administrator. IP Trunk The IP Trunk mode will typically be chosen for interoperability with existing TN802 (as opposed to the TN802B) IP Interface circuit packs.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 188 Circuit Pack The C-LAN and IP Interface assembly circuit packs must be administered on the Circuit Pack screen.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions ■ 189 outgoing calls are blocked on this signaling group; if so administered, blocked calls are diverted to alternate routes (either IP or circuits) as determined by the administered routing patterns You can use the default values set for these parameters, or you can change them to fit the needs of your network.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions 190 H.323 Trunk Administration — Task Summary After the enabling administration is complete, you can administer the H.323 IP trunks. The screens and fields that need to be administered are listed below. NOTE: This is only a list of screens and the fields that need to be administered.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions ■ Name ■ Network uses 1’s for broadcast address? 191 Signaling Group Each H.323 trunk must be assigned to a signaling group.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions Issue 1 April 2000 192 page 4—trunk group members assignment ■ Port ■ Code ■ Name ■ Night ■ Sig Grp Network Regions The Region field on the IP Interfaces screen allows you to set up segregated groups of C-LAN and IP Interface (Medpro) resources. This feature can be used in a variety of ways. For example, you could use regions to allocate specific C-LAN and IP Interface boards to H.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions Issue 1 April 2000 193 software applications running on a PC that is connected to DEFINITY ECS over an IP network. The single network connection between the PC and the DEFINITY ECS carries two channels, one for the signaling path and one for the voice path. DEFINITY IP Softphone handles the call signaling and an H.323 V2-complilant audio application, such as Microsoft NetMeeting 3.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions Figure 13. ■ Issue 1 April 2000 194 Road-Warrior Configuration (Voice over IP) Telecommuter Configuration (Dual Connection The telecommuter configuration of DEFINITY IP Softphone enables telecommuters to use the full DEFINITY ECS feature set from home. In this configuration, you use two connections to the DEFINITY server.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions Issue 1 April 2000 195 this telephone will be dialed during the current call. When the DEFINITY server no longer controls the telephone line, you can place calls from the telephone attached to the telephone line.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions ■ 196 Stand-alone H.323 Configuration (Voice over IP The stand-alone H.323 configuration enables users to place and receive calls via an H.323 V2-compliant audio application, such as Microsoft NetMeeting 3.0x, running on a PC that is connected to DEFINITY ECS over an IP network. Since this configuration offers limited call-handling capabilities, the stand-alone H.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 197 Once you’re finished administering your DEFINITY system, you need to install the IP Softphone software on each user’s PC. If you are using the road-warrior configuration, you also need to install an H.323 v2 compliant audio software application, such as Microsoft NetMeeting.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 198 NOTE: You choose to change an existing DCP extension by using change station nnnn in this step, where nnnn is the existing DCP extension.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions Issue 1 April 2000 199 Instructions for adding a telecommuter application Assign this configuration to remote users who have two available phone lines. For example, to administer a telecommuter application for a home user at extension 3010, complete the following steps: 1. Type add station 3010 and press RETURN. The Station screen appears. NOTE: Use the add station command if this is a new DCP extension.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions 200 TN802B IP Interface operating in MedPro mode for H.323 functionality. The TN799/TN799B is also required to support ATM interfaces and WAN PNC on DEFINITY R7 or later. The TN799/TN799B does not support BX.25 connectivity on the R8 or later csi platform. On the other platforms, TN765 Processor Interface and TN577 Packet Gateway circuit packs provide BX.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 201 (identified as the gateway on the IP route screen) to a router (identified as the destination on the IP route screen). Then the router is identified as the gateway and the remote node as the destination in another IP route. In R8, you can specify a default gateway on the IP Interfaces screen for each IP interface.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 202 Screen Changes The data module screen has changed for both ethernet and ppp connections. The IP Routing screen has also changed.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 203 Data Module Screen (PPP) add data-module 1994 Page 1 of x DATA MODULE Data Extension: Type: Port: Link: Enable Link? 1994 ppp 01c1502 4_ n Name: COS: COR: TN: ppp on link 4 to node 4 1 1 1 ___ BCC: 2 Node Name: ppp14 ___ Subnet Mask: 255.255.255.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 204 When to use IP routes You need to define host and/or network IP routes only in special cases when default gateways are not defined or when you want to limit communication between nodes. This section describes the network configurations that require explicit IP routes. There are two type of IP routes — host and network.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements IP Solutions 205 creates 2 usable subnetworks whose IP addresses are 192.168.1.64 (0100000 = 64) and 192.168.1.128 (1000000 = 128) .Serviceability Tools for C-LAN ■ ■ The C-LAN feature of the DEFINITY® system provides TCP/IP connectivity over Ethernet or PPP (Point to Point Protocol) to adjuncts such as CMS Call Center, Intuity™ AUDIX® and for DCS connectivity.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements IP Solutions 2 206 Trace-route trace-route ip-address 106.245.27.205 board 1c11 TRACE ROUTE RESULTS Hop Time(ms) 1 2 3 4 10, 15, 23, 23, 12, 15, 26, 25, IP Address 11 12 26 25 124. 9. 5.103 124. 9. 14. 23 122.245. 15.111 122.245. 27.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 207 Ping IP Address ping ip-address 192.68.9.26 board 1B07 PING RESULTS End-pt 192.68.9.26 Port 1b0701 Port Type MED-PT Result PASS Time(ms) 205 Error Code Variable Length Ping ping ip-address 192.11.128.111 packet-length 1500 PING RESULTS End-pt IP Port Port Type Result Time(ms) 192.11.128.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 208 Packet Error History ■ In C-LAN Release 7, the capability of checking packet error was provided, but was simply displayed on the board counters. ■ Now there is the capability of having a historical view of packet errors. Packet error history provides a 24-hour history of important packet level statistics that indirectly indicate some LAN performance characteristics.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements IP Solutions 209 List Measurements - PPP list measurements clan ppp screen ■ Authorization: init, inads, customer and craft logins ■ Syntax: list measurements clan ppp [cabinet(1-%d)]; carrier(A-E); slot(00%d); circuit(01-16) ■ Help: Enter [‘number’ ‘x’] [‘to-number’ ‘x’] [‘count’ ‘n’] ■ Date - This field sets the current date that the action was done.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 211 Networking - ATM DEFINITY ATM Networking uses open standards to integrate DEFINITY functionality with ATM transmission and switching. This allows you to use DEFINITY ECS applications over an ATM infrastructure throughout an enterprise. This convergence of voice and data networking is made possible by an ATM Services Card and ATM software that integrate into the DEFINITY ECS.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 212 network cabinets can be administered as separate locations; however, it is not required. You can use multiple ATM switches without multiple locations administered. The following figure shows and example of the basic ATM connections for Release 8r and Release 8csi system using ATM-PNC and ATM-CES.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 213 ATM Hardware Hardware required for ATM-PNC or ATM-CES: ■ TN2305 (multimode) or TN2306 (single mode) ATM interface circuit pack TN2238 R6.3 R7 R8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 214 Administering ATM-CES amd ATM-PNC Acquiring ATM Addresses Equipment that interfaces with an ATM switch must have a unique 40-digit (20byte) ATM address. These 40 characters are divided into sectors as Table 1 shows: Table 1. ATM addressing Hex digit position Length (hexadecimal) 1-26 26 Network prefix that identifies a particular ATM switch in the network.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 2. 215 ATM address formats Format Data Country Code (DCC) International Code Designator (ICD) ISDN E.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 216 Table 3 outlines important concepts to observe when administering ATM. Table 3. General DEFINITY ECS ATM parameters Concept Description PNC duplication If you are installing or upgrading a critical reliability system, you must enable the PNC duplication on the system-parameters customer-options screen (init password required) before the feature can be used.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 4. √ Step 1. 217 ATM-PNC administration Action Command Log on DEFINITY ECS switch Description Use the init login to log on to the DEFINITY switch. NOTE: An init login is required to change customer options and will be challenged by Access Security Gateway (ASG). Contact your regional CSA (customer software administrator) to perform this function. 2.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 4. √ 218 ATM-PNC administration — Continued Step Action 11. Set the MAC address (Steps 10-13) Command Description Set Address format to one of the following: E.164 ATM private, DCC, or ICD NOTE: If other ATM applications are installed ask the ATM system administrator to determine which address format to use. The system default is DCC. 12.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 4. √ 219 ATM-PNC administration — Continued Step Action Command 21. Set secondary timing reference 22. Save translations Description Set secondary: atm-sw. Press Enter to effect the changes. save translations Save translations to system disk.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 5. 220 Maximum number of ATM interface TN2305/TN2306 circuit packs Platform Maximum ATM circuit packs allowed Description r 88 2 x 44 port networks (CES) si, csi, c 6 CES only ATM-CES rules Table 6 lists several guidelines for ATM-CES administration. Table 6.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 6. 221 ATM-CES administration rules — Continued Rule How to administer or confirm The D channel must be in a port between 009 and 032. Type display signaling-group siggrpnbr and press Enter; go to screen 2 to verify. The D channel is automatically populated in channel 24 (T1) or in channel 16 (E1). The TN2305/TN2306 circuit packs provide up to 248 ports for trunking.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 223 makes the ATM board appear as if it does. This concept is depicted in Figure 3-1. Multiple TN2305/TN2306 circuit packs in a port network could connect to different ATM switches. 3 1 4 2 cydaces LJK 111199 Figure Notes 1. DEFINITY ECS PPN or EPN 2. TN2305/TN2306 circuit pack in any port 4. Ports 24 maximum (T1), including D-channel 31 maximum (E1), including D-channel 3.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 ■ 224 ATM-CES direct-connect configurations (two CES circuit packs linked by fiber, with no intervening switches). Observe the note in step 16. NOTE: The screens shown are for a Release 8r platform. The screen numbers may differ for Release 8c, Release 8csi, and Release 8si platforms. Table 9. √ ATM-CES administration Step 1.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 9. √ 225 ATM-CES administration — Continued Step Action Description 11. Set the synchronization Set the Synchronization Capable field to n (default). NOTE: Up to 44 boards may be designated synchronization capable on R8r and 3 boards on R8si, R8csi, R8c.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 9. √ 226 ATM-CES administration — Continued Step Action Description 17. Set VCI Set the Virtual Channel Identifier (VCI) field (321023). This number must be unique among signaling groups that share the same ATM circuit pack. NOTE: For a direct connection (two fiber-connected CES circuit packs), specify the same VCI at both ends of the emulated circuit.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 9. √ 227 ATM-CES administration — Continued Step Action Description 27. Verify channel settings Go to screen 2; Screen 8 displays. Depending on the settings in step 18: ■ If Circuit Type field is set at T1, then channel 24 is populated. ■ If Circuit Type field is set at E1, then channel 16 is populated. Other details about D-channels: 28.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 9. √ 228 ATM-CES administration — Continued Step Action Description 30. Set final fields Set the following fields (tabbing goes horizontally): ■ Group Type: field to isdn. NOTE: A trunk group can contain either ISDN or ATM trunks, but not both. ■ The CDR Reports field defaults to y. ■ The Carrier Medium: field to ATM. ■ The TAC: field to match customer’s dial plan.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 229 change system-parameters customer-options OPTIONAL FEATURES Abbreviated Dialing Enhanced List? Access Security Gateway (ASG)? Analog Trunk Incoming Call ID? A/D Grp/Sys List Dialing Start at 01? Answer Supervision by Call Classifier? ARS? ARS/AAR Partitioning? ARS/AAR Shortcut Dialing? y y y y y y y n ASAI Proprietary Adjunct Links? Async. Transfer Mode (ATM) PNC? Async.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 230 change system-parameters duplication Page 1 of DUPLICATION RELATED SYSTEM PARAMETERS 1 SPE B Enable Operation of SPE Duplication? y Enable Operation of PNC Duplication? y Screen 5. Duplication related system parameters ATM TRUNK-BOARD Location: 2E08 Name: _______________ Synchronization Capable: 1 Screen 6.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 10. 231 Country and protocol version supported (for Screen 7) Value Country Protocol supported 1-a United States, Canada AT&T TR41449/41459 (tested with AT&T, Canadian, and MCI networks) 1-b United States Bellcore TR 1268; NIUF.302; ANSI T1.607 2 Australia AUSTEL TSO14.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 232 add signaling-group next Page 2 of SIGNALING GROUP Chan __1: __2: __3: __4: __5: __6: __7: __8: __9: _10: _11: _12: _13: _14: _15: _16: Port Chan Port ___ _17: ___ ___ _18: ___ ___ _19: ___ ___ _20: ___ ___ _21: ___ ___ _22: ___ ___ _23: ___ ___ _24: 0cc (T1 only) ___ ___ ___ ___ ___ ___ ___ Occ (E1 only) Screen 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM add trunk-group GROUP MEMBER ASSIGNMENTS Port 233 Page 4 of 10 TRUNK GROUP Administered Members (min/max): 0/0 Total Administered Members: 0 Code Sfx Name Night Sig Grp 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: 11: 12: 13: 14: 15: Screen 10. Trunk group—screen 4 Changing the port-to-channel mapping Use the following steps to change the port-to-channel mapping for emulated circuits: 1.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 234 DEFINITY commands for CES Administration commands that are useful in working with CES are listed in Table 11. Table 11. ATM administration commands Command Description display circuit-packs cabinet Displays the packs in the cabinet, identifying ATM Trunk as well as ATM PNC EI boards. ATM Interface boards have not been specified as CES or PNC yet.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 12. √ Administer location procedure Step 1. 235 Action Description Activate the feature Type change system-parameters customer-options and press Enter. (Init password required.) The Customer Options screen displays. Go to screen 3 (Screen 11). 2. Set multiple locations Change the value in the Multiple locations field to y and press Enter.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 12. √ Administer location procedure — Continued Step 9. 236 Action Description Administer cabinet locations Administer all other locations as necessary. For example, if the PPN is in New York and a group of EPNs is in Los Angeles, then New York (location 1) is the reference and is administered with no time offset (see step 8).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 237 change system-parameters customer-options OPTIONAL FEATURES Hospitality (Basic)? Hospitality (G3V3 Enhancements)? H.323 Trunks? IP Stations? ISDN Feature Plus? ISDN-BRI Trunks? ISDN-PRI? Malicious Call Trace? Mode Code for Centralized Voice Mail? Mode Code Interface? Multifrequency Signaling? Multimedia Appl.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 238 Field description: Location number associated with the cabinet (range is 1-44, default 1). Location ■ Field cannot be blank ■ Location is display-only if the Multiple locations field (change system-parameters customer-options) is not set to y.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 239 Name This15-character field identifies the location but may be blank for any given location (default = y). Timezone Offset This field specifies the time offset from the system standard time. Set a value in the ±, hour (0-23),and minute (0-59) areas, as these fields cannot be blank for an administered location.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 240 2 fields specifying the number of hours (0-23) and minutes (0-59) the clock is moved ahead to begin daylight savings time (and moved back to return to standard time). Increment NOTE: Some states (Arizona) or portions of states (Indiana) do not observe daylight savings time. Verify the daylight savings time status in all your locations.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 241 You can administer the setup time thresholds, cache holding times, and total cache size, which can mitigate the effects of long interconnection setup delays. The change atm svc-cache command (Screen 16) is restricted to init, inads, and craft logins.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 242 Field description: Algorithm The name of the cache algorithm (default is lan). Possible values are none, lan, man, wan, and custom.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 2 Table 13. √ Gain/loss adjustment procedure Step 1. 243 Action Description Set or verify gain/loss administration Type change system-parameters country-options and press Enter. The System Parameters Country-Options screen displays (Table 17). 2. Set digital loss plan Domestic: Ensure that the Digital Loss Plan field is 1. If it is, exit this procedure.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 244 change system-parameters country-options Page 1 of 21 SYSTEM PARAMETERS COUNTRY-OPTIONS Companding Mode: Mu-Law 440Hz PBX-dial Tone? n Digital Loss Plan: 1 Analog Ringing Cadence: 1 Analog Line Transmission: 1 64/84xx Display Character Set? roman TONE DETECTOR PARAMETERS Tone Detection Mode: 6 Interdigit Pause: short Screen 17.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM ■ ATM Network Duplication configurations come equipped with a simplex SPE complex in the PPN, duplicate connectivity over ATM to all PNs and duplicate ATM interfaces in each PN. ■ The EPN configuration for ATM Network Duplication is the same as that for an EPN equipped for ATM critical reliability.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 246 ■ Both an expansion control carrier and a port carrier are required in each EPN. ■ Each of the two TN2305 or TN2306 ATM interfaces and tone clocks are placed in each of the two carriers. ■ A TN771 facility test circuit pack is required in each port network of a R8r system equipped for ATM Network Duplication.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM ■ 247 Once the ATM Interfaces, tone clocks, and ATM B-PNC addresses have been administered for all EPNs, the change system-parameters duplication command is issued. This brings up the DUPLICATION-RELATED SYSTEM PARAMETERS form. The Enable Operation of PNC Duplication? option is then changed to y. The option for Enable Operation of SPE Duplication? must remain as n.
What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 249 Interworking with Bandwidth Constricted ATM Networks Conserving ATM Bandwidth Introduction This is a recommendation to allow DEFINITY® R8r systems using ATM Port Network Connectivity to perform optimally when bandwidth is at a premium. ■ ATM bandwidth can be conserved, where possible, through optimal DEFINITY® resource allocation.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM ■ 250 ATM-PNC operation is the same from the DEFINITY® system perspective as if OC-3 is deployed end-to-end, except when traffic exceeds the carrying capacities of the IMA links, and contention occurs.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 251 ■ Integrated announcement board resources are associated with extension numbers and are often triggered by vector directory numbers (VDNs). ■ R8r can be traffic engineered and administered to minimize the number of the expensive SVCs using existing software.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 252 Improved Resource Allocation ■ ATM bandwidth can be conserved, where possible, through optimal DEFINITY® resource allocation. — Resources that can be optimally placed can include general purpose tone receivers, TN750/B/C multiple announcement boards, and TN771 maintenance test boards. ■ R8r can support up to 10 TN750/B/C integrated announcement boards.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 253 ■ Technicians should consider lowering the Activation threshold, and raising the delay time threshold. ■ If an ATM-IMP becomes alarmed unnecessarily, it is preferable to raise the delay threshold rather than raising the Activation threshold. System Setup Alarms ■ A System SETUP alarm uses the existing MO_ATM_IMP maintenance object.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 254 ■ The Off board ATM Network Alarms field will appear regardless of the option for ATM PNC, but will not appear if the system is a csi or si. ■ The set options command can change alarm levels. ■ Provides the ability to downgrade the off board ATM-NTWK alarm level from minor to warning level, or vice versa.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM ■ 255 The commands are available if Asynch. Transfer Mode (ATM) PNC? is enabled via the form resulting from the command change systemsparameters customer-options, regardless of the administered software version.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 256 ■ AddParty Count: the number of ADDPARTY requests processed. Values: 0 - 9999999 ■ Total Count: the total number of SETUP and ADDPARTY requests. Values: 0 - 9999999 ■ Average Latency: average latency in milliseconds for SVC type described during the time period indicated.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 258 Form Pages ■ Up to 100 entries will be listed if no selection criteria are indicated, otherwise all available are provided. Form Fields ■ Switch Name: The value administered on the system-parameters features form. ■ Date: Time/date that the command is being executed.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 259 ATM-Related System Parameters Form change system-parameters atm Page 1 ATM-RELATED SYSTEM PARAMETERS THRESHOLDS OF SETUP EVENTS TO DECLARE IMPAIRMENT Activation (%): 4 Deactivation (%): 3 Timeout (msec): 1000 TREATMENT DURING IMPAIRED CONDITIONS Deny Calls Using Impaired Paths? n Command: ■ Activation (%): Field — Values for this field can be any whole number from 1 to 20.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM ■ Issue 1 April 2000 260 Deactivation (%) — Use: This field specifies the percentage of setup events for a path to come out of the impaired state. That is, if the percentage of setup events for an impaired path meets or drops below this administered value, then it is no longer impaired. An alarm is retired when there are no more impaired paths originating from that ATM-IMP.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 261 Upgrades ■ Upgrades of R6r and R7r ATM PNC equipped systems to R8r will use the capabilities of conserving ATM Bandwidth without additional feature administration. ■ Upgrades of critically duplicated r systems to R8r are call preserving.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 262 Alarm Deactivation ■ The alarm condition for a given ATM-IMP is resolved whenever the number of active SETUP events drops to or below the Deactivation value on the ATM-RELATED SYSTEM PARAMETERS form for all paths originating at that ATM-IMP (i.e., all paths become unimpaired). — If the activation threshold is 5%, then the clearing threshold can be 0%, 1%, 2%, 3%, or 4%.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 263 ■ If they are not denied, current operation for delayed SVCs means that it is possible that the called party hears ringing, goes off-hook and initially cannot hear the calling party or cannot be heard by the calling party, or both cannot hear each other until one-way SVCs in both directions are established. ■ The drop on failure operation is maintained for failed calls.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM 264 Interactions between Call Processing Software and Maintenance Software ■ Call processing software and maintenance software work together to provide alarm activation and deactivation. ■ Call processing software will report event information to maintenance software that can result in maintenance software activating or deactivating alarms.
What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Issue 1 April 2000 Networking Enhancements Networking - ATM ■ 265 Intend is that these capabilities will provide administrators with an enhanced ability to isolate, diagnose, and correct problems quickly.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM ■ 266 If all appears normal in the error log, but the latencies are too high, may need to upgrade the ATM network to solve the problem. NOTE: fter the problem is fixed, the alarm will clear, but it will take an indeterminate amount of time.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 268 Example AT13A ATM-NTWK AT13A: 264 1507 11/17/15:01 11/17/15:01 23 0 1nn ATM connection number 13, PNC-A. 264: Error type: 256 + destination connection number 8 1507: Originating port network number is 15. Destination port network number is 7. This all means that the threshold for SVC setup events from connection # 13 to connection # 8 has been exceeded.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 269 ■ The Port is deciphered as: ATxyZ. xy is the connection number, not the port network number. ■ The mapping between connection number and port network number can be found with the command list atm pnc. ■ The alarm indicates that at least one path originating from the displayed Port, has exceeded the SVC setup threshold.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 270 T1 401A/E1 402A/E1 403A Synchronization Splitters A DEFINITY ATM-PNC requires network synchronization for DS1 circuit packs not to slip relative to the LEC/IXC switches. The ATM switch serves as the sync reference source for the DEFINITY. The ATM switch, in turn, derives primary and secondary sync.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 271 3 4 J1 2 J2 2 1 crda400a LJK 071698 Figure Notes: a. 1. From network interface 3. Timing output port (J1) to the ATM switcha 2. Amphenol connection to DEFINITY ECS 4. Timing output port (J2) to the ATM switcha Ports J1 and J2 provide identical DS1 timing source signals to the ATM switches.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 272 3 2 M AR AL K OR TW NE 5 nt ce Lu s ie og ol hn c Te 1A 8 40 807 50 1 08 T M R OH 0 TE IT 10 L SP NC Y S 1 TO M AT crda401a KLC 020300 1 TO DEFINITY 2 CH IT SW 4 5 Figure Notes: 1. Amphenol connector to DEFINITY ECS 2. Network timing connection a. 3. Timing alarm lead connection 4. Timing output ports (RJ45) to ATM switcha 5. Jumpers and capacitors (inside case).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 273 3 2 K OR TW NE M AR AL s ie og ol hn ec T nt ce Lu 5 2A 4 40 809 50 1 08 E M R OH 0 TE 12 LIT P S NC SY 1 TO M AT crda402a KLC 020300 1 TO DEFINITY 2 CH IT SW 4 5 Figure Notes: 1. Amphenol connector to DEFINITY ECS 2. Network timing connection a. 3. Timing alarm lead connection 4. Timing output ports (RJ45) to ATM switcha 5. Jumpers and capacitors (inside case).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 274 5 4 TX K RX OR TW NE s ie og ol hn c Te nt ce Lu 3A 2 40 810 50 08 1 1 M 75 1 OH NC E SY TO M AT R TE IT L SP crda403a KLC 020300 6 TO DEFINITY 2 CH IT SW 6 3 2 Figure Notes: 1. Amphenol connector to DEFINITY ECS 4. Network receive connection, BNC connector 2. Synchronization source (timing output ports) to ATM switch1 5.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 Networking Enhancements Networking - ATM 275 NETWORK ALARM 4 8 7 5 6 3 RX 4 3 2 1 TX 2 402A 108508094 120 OHM E1 SYNC SPLITTER 1 TO DEFINITY 2 5 TX 6 5 4 3 2 1 6 TX TO ATM SWITCH jpda40xa KLC 020300 Figure Notes: 1. Amphenol connection to DEFINITY ECS switch 2. Row of capacitors 3. Jumpers for incoming network connections 4. Incoming network transmit and receive connections 5.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 276 Synchronization splitter connections The splitter connects to a timing source. Figure 22 shows the synchronization connections through a DSU/CSU (400A), and Figure 23 shows the synchronization connections through an ICSU (400A). Figure 24 shows the synchronization connections directly to the timing source (401A, 402A, 403A).
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 277 Use the information in Table 15 to determine the maximum cable run lengths for the configuration. 7 8 6 5 1 9 4 3 2 cydaatm1 LJK 020100 Figure Notes: 1. Public Switched Telephone Network (PSTN) 5. H600-383 quad cable from sync splitter to ATM switch A 2. Main Distribution Frame (MDF) or smart jack 6.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 278 1 3 2 4 7 6 8 5 cydaatm3 KLC 020200 Figure Notes: 1. Public switched telephone network (PSTN) 5. H600-383 quad cable from sync splitter to ATM switch A 2. Main distribution frame (MDF) or smart jack 6. H600-383 quad cable from sync splitter to duplicated ATM switch B (critical reliability/ATM network duplication) 3. H600-383 quad cable 4.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 279 Use the information in Table 15 to determine the maximum cable run lengths for the configuration. Table 15.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM 280 Table 16 lists the splitter model(s) applicable to specific countries. Table 16.
Issue 1 April 2000 What’s New in DEFINITY ECS Release 8.2 Job Aid 555-233-754 2 Networking Enhancements Networking - ATM Table 16.
What’s New in DEFINITY ECS Release 8.
