Data Sheet

SPECIFICATION
(for D type only)
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
EFFICIENCY (Typ.)
INPUT
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
DC CURRENT (Typ.)
5V 12V 24V
18A 20A 8.5A 4.2A
0 ~ 18A 0 ~ 20A 0 ~ 8.5A 0 ~ 4.2A
90W 100W 102W 100.8W
100mVp-p 120mVp-p 150mVp-p
±2.0% ±1.0% ±1.0%
4.5 ~ 5.5VDC 11 ~ 16VDC 23 ~ 30VDC
±0.5%
±0.5%
±0.3%
±0.3%
±0.2%
±0.2%
2s, 50ms(only D mode) at full load
20ms(only D mode) at full load
A:9.5 ~ 18VDC B:19 ~ 36VDC C:36 ~ 72VDC D:72 ~ 144VDC or 85 ~ 132VAC
D:18A/96VDC
<0.75mA/120VAC(SD-100D)
105 ~ 135% rated output power
5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load
31.5 ~ 37.5V
5% load
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Compliance to EN55032 (CISPR32) Class B, EAC TP TC 020
IEC62368-1 CB approved by TUV (for D type only), approvedEAC TP TC 004
Compliance to EN61000-4-2,3,4,6,8, light industry level, criteria A, EAC TP TC 020
-15 ~ +60 (SD-100A), -10 ~ +60 (SD-100B/C/D) (Refer to "Derating Curve")℃℃
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH non-condensing℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
399.9K hrs min.(SD-100A) 356.7K hrs min.(SD-100B) 355.5K hrs min.(SD-100C) 341.9K Hrs min.(SD-100D) MIL-HDBK-217F (25)℃
199*98*38mm (L*W*H)
0.65Kg; 20pcs/13.8Kg/0.8CUFT
File Name:SD-100-SPEC 2020-01-10
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
100W Single Output DC-DC Converter

2:1 wide input range
Protections: Short circuit / Overload / Over voltage
1500VAC I/O isolation
Built-in EMI filter, low ripple noise
Low cost
High reliability
2 years warranty
■
Features :
SD-100 series
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
1. All parameters NOT specially mentioned are measured at 12,24,48,96VDC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a mm* mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.360 360 For guidance on how to
perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
5. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
EMC IMMUNITY
EMC EMISSION
SD-100B-5SD-100A-5 SD-100C-5 SD-100D-5 SD-100B-12 SD-100C-12 SD-100D-12 SD-100A-24 SD-100B-24 SD-100C-24 SD-100D-24 SD-100A-12
74%78%
4.8A/24V
9.7A/12V 10.4A/12V 10A/12V 4.8A/24V 4.8A/24V
75% 76% 75%82%
2.4A/48V 2.4A/48V2.4A/48V
77% 80% 78%84% 81% 83%
1.8A/96V 1.8A/96V 1.8A/96V
31.5 ~ 37.5V/10% load
TPTC004 IEC62368-1