Data Sheet

ManualsBrandsMEAN WELL ManualsPOWERDC Power Supply 1.5kW 12V 125A

SPECIFICATION

1600W Power Supply with Single Output

RSP-1600 series

File Name:RSP-1600-SPEC 2018-01-15

RSP-1600-12 RSP-1600-24 RSP-1600-27

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

HOLD UP TIME (Typ.)

VOLTAGE RANGE

Note.5

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

AC CURRENT (Typ.)

Note.5

12V 24V 27V

125A 67A 59A

0 ~ 125A 0 ~ 67A 0 ~ 59A

1500W 1608W 1593W

150mVp-p

11.5 ~ 15V

200mVp-p 200mVp-p

23.5 ~ 30V 26.5 ~ 33.5V

±1.0% ±1.0% ±1.0%

±0.5%

1500ms, 60ms/230VAC at full load

16ms / 230VAC at 75% load 10ms / 230VAC at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

0.97/230VAC at full load

89%

COLD START 35A/230VAC

14A/115VAC 8A/230VAC

15A/115VAC 8.5A/230VAC

<2mA / 230VAC

RSP-1600-48RSP-1600-36

48V36V

33.5A44.5A

0 ~ 33.5A0 ~ 44.5A

1608W1602W

300mVp-p250mVp-p

47.5 ~ 58.8V35.5 ~ 45V

±1.0%±1.0%

±0.5% ±0.5% ±0.5%±0.5%

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.4

91.5% 92% 93%92%

OVER TEMPERATURE

OVERLOAD

OVER VOLTAGE

105 ~ 115% rated output power

15.75 ~ 18.75V

Protection type : Shut down o/p voltage, re-power on to recover

Protection type : Shut down o/p voltage, recovers automatically after temperature goes down

31.5 ~ 37.5V 35.2 ~ 41.9V 63 ~ 75V47.2 ~ 56.3V

PROTECTION

ALARM SIGNAL

REMOTE SENSE

REMOTE ON-OFF CONTROL

AUXILIARY POWER

5V @ 0.3A, 12V @ 0.8A

FUNCTION

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

-30 ~ +70 (Refer to "Derating Curve")℃

20 ~ 90% RH non-condensing

-40 ~ +85 , 10 ~ 95% RH℃

non-condensing

±℃ ℃0.03%/ (0 ~ 50 )

ENVIRONMENT

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

SAFETY STANDARDS

WITHSTAND VOLTAGE

UL60950-1, TUV EN60950-1 EAC TP TC 004 approved

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC

ISOLATION RESISTANCE

MTBF

DIMENSION

PACKING

OTHERS

160.9K hrs min. Telcordia SR-332 (Bellcore) ; 42.1K hrs min. MIL-HDBK-217F (25 )℃

300*85*41mm (L*W*H)

SAFETY &

EMC

(Note 7)

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

2.1Kg;6pcs/13.6Kg/1.03CUFT

Parameter

ESD

Radiated

EFT / Burst

Surge

Conducted

Magnetic Field

Voltage Dips and Interruptions

Conducted

Radiated

Harmonic Current

Voltage Flicker

Standard

EN55032 (CISPR32) / EN55011 (CISPR11)

EN61000-3-2

EN61000-3-3

EN61000-4-2

EN61000-4-3

EN61000-4-4

EN61000-4-5

EN61000-4-6

EN61000-4-8

EN61000-4-11

Test Level / Note

Class B

Class A

-----

NOTE

EMC IMMUNITY

EMC EMISSION

Isolated signal output for T-alarm and DC OK

Compensate voltage drop on the load wiring up to 0.5V. Please refer to the Function Manual

By electrical signal or dry contact Power ON:short Power OFF:open. Please refer to the Function Manual

Adjustment of output voltage is allowable to 40 ~ 125% of nominal output voltage (60 ~ 125% for 12V).

Please refer to the Function Manual.

EN55024 , EN61204-3, EN61000-6-2

Level 3, 8KV air ; Level 2, 4KV contact

Level 3

Level 4, 2KV/Line-Line 4KV/Line-Earth

Level 3

Level 4

>95% dip 0.5 periods, 30% dip 25 periods,

>95% interruptions 250 periods

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Under parallel operation ripple of the output voltage may be higher than the SPEC at light load condition. It will go back to normal ripple level once the

output load is more than 5%.

4. Tolerance : includes set up tolerance, line regulation and load regulation.

5. Derating may be needed under low input voltages. Please check the derating curve for more details.

6. PV/PC functions when users are not operating on PMBus/CANBus. SVR functions when users are neither operating on PMBus/CANBus nor using PV/PC.

7. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on

a mm* mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.720 360 For guidance on how to

perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)

8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

Protection type : Constant current limiting, unit will shut down o/p voltage after 5 sec. re-power on to recover

Adjustment of constant current level is allowable to 20 ~ 100% of rated current.

Please refer to the Function Manual.

OUTPUT VOLTAGE

PROGRAMMABLE(PV)

Note 6

OUTPUT CURRENT

PROGRAMMABLE(PC)

Note 6