Datasheet

..
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
VOLTAGE RANGE
Note.6
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY (Typ.)
INRUSH CURRENT (max.)
LEAKAGE CURRENT
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT
800ms, 50ms, 16ms at full load
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
PF>0.95/230VAC PF>0.98/115VAC at full load
72% 72% 74%
3.5A/115VAC 2A/230VAC
COLD START 45A
<2mA / 240VAC
105 ~ 150% rated output power
CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V
Protection type : Shut down o/p voltage, re-power on to recover
UL60950-1, TUV EN60950-1 Approved
-10 ~ +60 (Refer to output load derating curve)
20 ~ 90% RH non-condensing
-20~+85 ,10~95%RH
0.03%/ (0~50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
160.6K hrs min. MIL-HDBK-217F (25 )
230*115*50mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. 33.3% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
6. Derating may be needed under low input voltages. Please check the derating curve for more details.
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN55024, Light industry level, criteria AEN61000-4-2,3,4,5,6,8,11; ENV50204,
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
200W Quad Output with PFC Function
Features :
QP-200 series
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION
QP-200-3B QP-200-3C QP-200-3D
5V 5V 5V3.3V 12V -12V 3.3V 15V -15V 3.3V 24V -12V
15A 15A 10A15A 6A 0.7A 15A 5A 0.7A 15A 4A 0.7A
3~20A 3~20A 3~15A0~20A 0.5~8A 0~1A 0~20A 0.5~6A 0~1A 0~20A 0.4~5A 0~1A
204.9W 210W 203.9W
100mVp-p
CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V
100mVp-p 150mVp-p 150mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 150mVp-p 150mVp-p100mVp-p 100mVp-p
3.0% 3.0% 3.0% 3.0% 3.0% 3.0%+8,-10% 6.0% +10,-6% 6.0% +10,-6% 6.0%
1.0%1.0%1.0% 2.0% 1.0% 1.0% 2.0% 1.0% 1.0%1.0% 2.0% 1.0%
2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0%6.0% 2.0% 6.0% 6.0%
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
File Name:QP-200-SPEC 2004-12-14
INPUT
OVER TEMPERATURE
POWER GOOD / POWER FAIL(OPTIONAL)
10ms/1ms
FUNCTION
Protection type : Constant current limiting, recovers automatically after fault condition is removed
95 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor
20A 20A 8A 1A 20A 7A 1A 20A 6A 1A20A 20APEAK CURRENT Note.4
Universal AC input / Full range
Built-in active PFC function, PF>0.95
Protections:Short circuit/Over load/Over voltage/Over temperature
Forced air cooling by built-in DC fan
CH1,2 can be adjustable from -5~+10%
With power good and fail signal output(Optional)
Built-in remote sense function for CH1,2
100% full load burn-in test
CH4 can set to positive after consult us before delivery
Fixed switching frequency at PFC:67KHz PWM:134KHz(Optional)
3 years warranty
1.2Kg; 12pcs/15.4Kg/0.92CUFT
CH1 CH1 CH1 OUTPUT NUMBER CH2 CH2 CH2CH3 CH3 CH3CH4 CH4 CH4