Datasheet

..
SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD TIME
VOLTAGE RANGE
Note.6
FREQUENCY RANGE
POWER FACTOR
EFFICIENCY (Typ.)
INRUSH CURRENT (max.)
LEAKAGE CURRENT
SAFETY STANDARDS
HARMONIC CURRENT
EMS IMMUNITY
WORKING TEMP.
POWER GOOD / POWER FAIL(OPTIONAL)
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
AC CURRENT
800ms, 50ms, 16ms at full load
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
PF>0.95/230VAC PF>0.98/115VAC at full load
75% 75%
CH1: 5.75 ~ 6.75V CH2:17.25 ~ 20.25V
72%
CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V
3.5A/115VAC 2A/230VAC
COLD START 45A
<2mA / 240VAC
105 ~ 150% rated output power
CH1:5.75 ~ 6.75V CH2:13.8 ~ 16.2V
Protection type : Shut down o/p voltage, re-power on to recover
UL60950-1, TUV EN60950-1 Approved
-10 ~ +60 (Refer to output load derating curve)
10ms/1ms
20 ~ 90% RH non-condensing
-20~+85 ,10~95%RH
0.03%/ (0~50 )
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
160.6K hrs min. MIL-HDBK-217F (25 )
230*115*50mm (L*W*H)
1.2Kg; 12pcs/15.4Kg/0.92CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. 33.3% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power.
5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
6. Derating may be needed under low input voltages. Please check the derating curve for more details.
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
Compliance to EN55024, Light industry level, criteria AEN61000-4-2,3,4,5,6,8,11; ENV50204,
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
200W Quad Output with PFC Function
Universal AC input / Full range
Built-in active PFC function, PF>0.95
Protections:Short circuit/Over load/Over voltage/Over temperature
Forced air cooling by built-in DC fan
CH1,2 can be adjustable from -5~+10%
With power good and fail signal output(Optional)
Built-in remote sense function for CH1,2
100% full load burn-in test
CH4 can set to positive after consult us before delivery
Fixed switching frequency at PFC:67KHz PWM:134KHz(Optional)
3 years warranty
Features :
QP-200 series
ENVIRONMENT
SAFETY &
FUNCTION
EMC
(Note 5)
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
EMI CONDUCTION & RADIATION
QP-200D QP-200F QP-200-3A
5V 5V 5V12V
CH2 CH2 CH2
24V
CH3 CH3 CH3
-12V
CH4 CH4 CH4
15V 24V -15V 3.3V 12V -5V
15A 15A 15A4A 3A 0.7A 3A 3A 0.7A 15A 6A 0.7A
3~20A 3~20A 3~20A0~6A 0.4~5A 0~1A 0~5A 0.4~5A 0~1A 0~20A 0.5~8A 0~1A
203.4W 202.5W 200W
100mVp-p
20A
CH1: 4.75 ~ 5.5V CH2: 11.4 ~ 13.2V CH1: 4.75 ~ 5.5V CH2: 14.25 ~ 16.5V CH1: 4.75 ~ 5.5V CH2: 3.14 ~ 3.63V
150mVp-p
7A
150mVp-p
6A
150mVp-p
1A
150mVp-p
6A
150mVp-p
6A
150mVp-p
1A
100mVp-p
20A
150mVp-p
8A
150mVp-p
1A
100mVp-p
20A
100mVp-p
20A
3.0% 3.0% 3.0% 3.0% 3.0% 3.0%+10,-6% 6.0% +10,-6% 6.0% +8,-10% 6.0%
1.0%1.0%1.0% 2.0% 1.0% 1.0% 2.0% 1.0% 1.0%1.0% 2.0% 1.0%
2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0% 2.0%6.0% 2.0% 6.0% 6.0%
95 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
File Name:QP-200-SPEC 2004-12-14
INPUT
OVER TEMPERATURE
PEAK CURRENT
Note.4
Protection type : Constant current limiting, recovers automatically after fault condition is removed
CH1 CH1 CH1 OUTPUT NUMBER