Datasheet

SPECIFICATION
MPT-65A MPT-65B MPT-65C
MODEL
DCVOLTAGE
RATEDCURRENT
CURRENTRANGE
RATEDPOWER
OUTPUT
LINEREGULATION
LOADREGULATION
SETUP,RISETIME
HOLDUP TIME (Typ.)
VOLTAGERANGE
FREQUENCY RANGE
EFFICIENCY(Typ.)
INPUT
INRUSHCURRENT (Typ.)
LEAKAGECURRENT Note.7
WORKINGTEMP.
WORKINGHUMIDITY
STORAGETEMP.,HUMIDITY
TEMP.COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVERVOLTAGE
ACCURRENT (Typ.)
5V 12V
CH2
-5V
CH3
5V
CH1
12V
CH2
-12V
CH3
5V
CH1
15V
CH2
-15V
CH3
5.5A 2.5A 0.5A 5.5A 2.5A 0.5A 5.5A 2A 0.5A
0.4~7A 0.2~3.2A 0~0.7A 0.4~7A 0.2~3.2A 0~0.7A 0.4~7A 0.2~2.6A 0~0.7A
60W 63.5W 65W
60mVp-p 120mVp-p 60mVp-p 60mVp-p 160mVp-p 100mVp-p 60mVp-p 180mVp-p 100mVp-p
¡Ó 4.0% ¡Ó 4.0% ¡Ó 4.0%
CH1:4.5~5.5V
+10,-7% +10,-7% +10,-7% ¡Ó 5.0% ¡Ó 5.0% ¡Ó 5.0%
¡Ó 1.0% ¡Ó 1.0% ¡Ó 1.0% ¡Ó 2.0% ¡Ó 1.0% ¡Ó 1.0% ¡Ó 1.0%
¡Ó 1.0% ¡Ó 1.0% ¡Ó 1.0%
¡Ó 2.0% ¡Ó 2.0%
¡Ó 3.0% ¡Ó 3.0% ¡Ó 3.0% ¡Ó 4.0% ¡Ó 4.0% ¡Ó 4.0%
90~264VAC127~370VDC
47~440Hz
74% 74% 74%
1.6A/115VAC1A/230VAC
COLDSTART 20A/115VAC40A/230VAC
73~95W ratedoutputpower
5.75~6.75VDConCH1
Protectiontype: Hiccupmode,recoversautomaticallyafterfaultconditionisremoved
Protectiontype: Hiccupmode,recoversautomaticallyafterfaultconditionisremoved
-20~+85 ,10~95%RH ¢J
¡Ó ¢J ¢J 0.04%/ (0~50 )on+5Voutput
10~500Hz,2G10min./1cycle,periodfor60min. eachalongX, Y,Zaxes
275.1Khrsmin.MIL-HDBK-217F(25 ) ¢J
127*76*42mm(L*W*H)
0.27Kg;54pcs/16.8Kg/1.35CUFT
FileName:MPT-65-SPEC 2012-11-28
800ms,20ms/230VAC800ms,20ms/115VACatfullload
80ms/230VAC12ms/115VACatfullload
-10~+55 ¢J (Referto"DeratingCurve")
20~90%RHnon-condensing
SAFETY STANDARDS
ANSI/AAMIES60601-1, TUVEN60601-1,IEC60601-1approved
CompliancetoEN55011(CISPR11)ClassB, EN61000-3-2,-3
CompliancetoEN61000-4-2,3,4,5,6,8,11,EN60601-1-2,medicallevel,criteria A
VOLTAGE ADJ.RANGE
65W TripleOutputMedical Type
MPT-65 ser i e s
¡E
¡E
¡E
¡E
¡E
¡E
¡E
Universal AC input / Full range
Low leakage current <250 A
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Medical safety approved (2 x MOPP between primary to secondary)
100% full load burn-in test
Fixed switching frequency at 45KHz
3 years warranty
¡E
¡½
Features :
RIPPLE&NOISE(max.) Note.2
VOLTAGETOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC
(Note4)
PROTECTION
WITHSTANDVOLTAGE
ISOLATIONRESISTANCE
I/P-O/P:4KVACI/P-FG: O/P-FG:0.5KVAC1min.2KVAC
I/P-O/P,I/P-FG:100MOhms/500VDC /25 /70%RH ¢J
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Mounting holes M1 and M2 should be grounded for EMI purposes.
6. Heat Sink HS1,HS2 can not be shorted.
7. .
¢J
For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.
(as available on http://www.meanwell.com)
Touch current was measured from primary input to DC output
OUTPUTPOWER(max.) 72Wwith18CFMmin.Forcedairconvection
CH1 OUTPUTNUMBER
EMCIMMUNITY
EMCEMISSION
Earthleakagecurrent<250 A/264VAC, Touchcurrent<60 A/264VAC £g
£g
£g