Datasheet

25W Multiple-Stage Constant Current Mode LED Driver
LCM-25KN series
SPECIFICATION
MODEL
LCM-25KN
DC VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME Note.3
VOLTAGE RANGE Note.2
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.) Note.4
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
18.9W
59V
41V
500ms / 230VAC
180 ~ 277VAC 220 ~ 392VDC
47 ~ 63Hz
85%
20 ~ 90% RH non-condensing
-40 ~ +80℃, 10 ~ 95% RH
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
1.AllparametersNOTspeciallymentionedaremeasuredat230VACinput,ratedcurrentand25℃ofambienttemperature.
2.De-ratingmaybeneededunderlowinputvoltages.Pleasereferto“STATICCHARACTERISTIC”sectionsfordetails.
3.Lengthofsetuptimeismeasuredatfirstcoldstart.TurningON/OFFthedrivermayleadtoincreaseofthesetuptime.
4.Efficiencyismeasuredat500mA/50VoutputsetbyDIPswitch.
5.Standbypowerconsumptionismeasuredat230VAC.
6.Thedriverisconsideredasacomponentthatwillbeoperatedincombinationwithfinalequipment.SinceEMCperformancewillbeaffectedbythe
completeinstallation,thefinalequipmentmanufacturersmustre-qualifyEMCDirectiveonthecompleteinstallationagain.
7.Theambienttemperaturederatingof3.5℃/1000mwithfanlessmodelsandof5℃/1000mwithfanmodelsforoperatingaltitudehigherthan2000m(6500ft).
OPEN CIRCUIT VOLTAGE (max.)
ENVIRONMENT
SAFETY &
FUNCTION
EMC
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:>100M Ohms / 500VDC / 25℃/ 70% RH
CURRENT LEVEL
350mA 600mA500mA 700mA(default) 900mA 1050mA
CURRENT TOLERANCE
SHORT CIRCUIT
OVER TEMPERATURE
SYNCHRONIZATION
Constant current limiting, recovers automatically after fault condition is removed
Please refer to "SYNCHRONIZATION OPERATION” section
DIMMING
Please refer to "DIMMING OPERATION" section
TOTAL HARMONIC DISTORTION
<0.5mA / 240VAC
PF≧0.94/230VAC, PF≧0.91/277VAC@full load
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
COLD START 20A(twidth=260μs measured at 50% Ipeak) at 230VAC ; Per NEMA 410
±5%
±0.03%/℃ (0 ~ 50℃)
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
26 units (circuit breaker of type B) / 44 units (circuit breaker of type C) at 230VAC
File Name:LCM-25KN-SPEC 2019-09-12
(Please refer to "STATIC CHARACTERISTIC" section)
WORKING TEMP.
MAX. CASE TEMP.
Tcase=+85℃
Tcase=-30 ~ +85℃ (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)
CURRENT RIPPLE
5.0% max. @rated current
Current level selectable via DIP switch, please refer to”DIP SWITCH TABLE” section
THD< 20%(@load≧50%/230VAC; @load≧75%/277VAC)
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
Compliance to EN55015, EN61000-3-2 Class C(@load≧50%) ; EN61000-3-3; GB17625.1,GB17743, EAC TP TC 020
EMC IMMUNITY
<0.5W
STANDBY POWER
CONSUMPTION Note.5
EMC EMISSION Note.6
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level(surge immunity Line-Line 2KV), EAC TP TC 020
6 ~ 50V6 ~ 54V 6 ~ 42V 6 ~ 36V 6 ~ 24V6 ~ 28V
25.2W
0.17A/230VAC 0.15A/277VAC
Shut down o/p voltage, recovers automatically after temperature goes down
I/P-O/P:3.75KVAC ; I/P-DA±:1.875KVAC ; O/P-DA±:1.875KVAC
213.3K hrs min. MIL-HDBK-217F (25℃)
105*68*23mm (L*W*H)
0.173Kg ; 72pcs/13.5Kg/1.04CUFT
CSA C22.2 No.250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent,GB19510.14,GB19510.1,
EAC TP TC 004 approved
KNX STANDARDS
certification