Data Sheet

ManualsBrandsMean Well Manuals12V/DCHLN 12V/60W/5A LED power supply

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

CONSTANT CURRENT REGION

Note.4

HLN-80H-12

B : IP64 rated. Constant current level adjustable through output cable with 1~10Vdc or 10V PWM signal or resistance.

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

RATED POWER

OUTPUT

VOLTAGE ADJ. RANGE

Note.6

CURRENT ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

Note.8

HOLD UP TIME (Typ.)

VOLTAGE RANGE

Note.5

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT (Typ.)

INPUT

INRUSH CURRENT(Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS

Note.7

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVER CURRENT

Note.4

OVER VOLTAGE

OVER TEMPERATURE

Can be adjusted by internal potentiometer A type only

16ms at full load 230VAC /115VAC

90 ~ 305VAC 127 ~ 431VDC

47 ~ 63Hz

COLD START 70A(twidth=485 s measured at 50% Ipeak) at 230VACμ

<0.75mA / 277VAC

95 ~ 108%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

Compliance to EN55015, EN61000-3-2 Class C ( 60% load, 12V model 65% load) ; EN61000-3-3≧≧

Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, EN55024, light industry level (surge 4KV), criteria A

20 ~ 95% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃0.03%/ (0 ~ 40 )

10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes

356.4Khrs min. MIL-HDBK-217F (25 )℃

181*61.5*35mm (L*W*H)

0.5Kg; 24pcs/13Kg/0.75CUFT

Protection type : Shut down o/p voltage, re-power on to recover

80W Single Output Switching Power Supply



Universal AC input / Full range (up to 305VAC)

Built-in active PFC function

Protections: Short circuit / Over current / Over voltage / Over temperature

Cooling by free air convection

OCP point adjustable through output cable or internal potentiometer

Fully isolated plastic case with IP64 level

Class 2 power unit

Three in one dimming function (1~10Vdc or PWM signal or resistance)

Suitable for LED lighting and moving sign applications

Compliance to worldwide safety regulations for lighting

Suitable for dry / damp locations or outdoor application

3 years warranty

■ Features :

HLN-80H series

RIPPLE & NOISE (max.)

Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

PROTECTION

Shut down o/p voltage, re-power on to recover

SELV

IP64

A : IP64 rated. Output voltage and constant current level can be adjusted through internal potentiometer.

14 ~ 17V 18 ~ 24V

23 ~ 30V

28 ~ 35V

35 ~ 43V

41 ~ 49V 54 ~ 63V

48 ~ 58V 59 ~ 68V

88%

89%

90%

90.5%

91%

91%91% 91%

±2.5% ±2.0% ±1.0% ±1.0% ±1.0%

±1.0%

±0.5% ±0.5% ±0.5% ±0.5% ±0.5%

±0.5%

±2.0%

±1.5% ±1.0% ±0.5% ±0.5%

±0.5%

±1.0%

±0.5%

±1.0%

±0.5%

12V

HLN-80H-12 HLN-80H-30HLN-80H-15 HLN-80H-36HLN-80H-20 HLN-80H-42HLN-80H-24 HLN-80H-48 HLN-80H-54

15V 20V 24V 30V

36V

48V

5A 5A 4A 3.4A

2.7A

2.3A

1.7A

60W 75W 80W 81.6W 81W

82.8W

81.6W

150mVp-p 150mVp-p

13.5 ~ 17V

150mVp-p

17 ~ 22V

150mVp-p

22 ~ 27V

200mVp-p

27 ~ 33V

200mVp-p

33 ~ 40V

200mVp-p

43 ~ 53V10.8 ~ 13.5V

54V

1.5A

81W

200mVp-p

49 ~ 58V

42V

1.95A

81.9W

200mVp-p

38 ~ 46V

FMM

110

PF>0.96/115VAC, PF>0.96/230VAC, PF>0.94/277VAC at full load (Please refer to "Power Factor Characteristic" curve)

0.85A / 115VAC 0.425A / 230VAC 0.4A / 277VAC

UL8750, CSA C22.2 No. 250.0-08(except for 48V, 54V), EN61347-1, EN61347-2-13 independent ; IP64, J61347-1,

J61347-2-13 approved ; Design refer to UL60950-1, TUV EN60950-1

3 ~ 5A 3 ~ 5A 2.4 ~ 4A 2.04 ~ 3.4A 1.62 ~ 2.7A

1.38 ~ 2.3A

1.02 ~ 1.7A 0.9 ~ 1.5A

1.17 ~ 1.95A

7.2 ~12V 9 ~ 15V 12 ~ 20V 14.4 ~ 24V 18 ~ 30V

21.6 ~ 36V

28.8 ~ 48V 32.4 ~ 54V

25.2 ~ 42V

-40 ~ +50 (Refer to "Derating Curve")℃

EMC IMMUNITY

EMC EMISSION

( except for 48V,54V )( for 48V,54V only)

SHORT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed

File Name:HLN-80H-SPEC 2014-08-14

1200ms,80ms/115VAC 500ms,80ms/230VAC at full load ; B type 1200ms,200ms/115VAC 500ms,200ms/230VAC at 95% load

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Please refer to "DRIVING METHODS OF LED MODULE".

5. Derating may be needed under low input voltages. Please check the static characteristics for more details.

6. A type only.

7. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1, FCC part18.

8. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.

9. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by

the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

10. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently

connected to the mains.

Summary of content (5 pages)

PAGE 1
HLN-80H 80W Single Output Switching Power Supply series ■ Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function Protections: Short circuit / Over current / Over voltage / Over temperature Cooling by free air convection OCP point adjustable through output cable or internal potentiometer Fully isolated plastic case with IP64 level Class 2 power unit Three in one dimming function (1~10Vdc or PWM signal or resistance) Suitable for LED lighting and moving sign applic
PAGE 2
HLN-80H 80W Single Output Switching Power Supply Mechanical Specification Case No.HLN-80A series Unit:mm A Type:(HLN-80H-_A) 181 300±20 90.5 +V(Red) -V(Black) SVT 18AWG×2C T case 21.25 SVT 18AWG×3C 6.26 35 ※ T case: Max. Case Temperature. 2.3 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 2-R2.5 61.5 300±20 30.75 21.25 6.26 ※IP64 rated. Output voltage and constant current level can be adjusted through internal potentiometer. (can access by removing the rubber stopper on the case).
PAGE 3
HLN-80H 80W Single Output Switching Power Supply Derating Curve series Static Characteristics 100 100 90 80 80 230VAC Input only 70 LOAD (%) LOAD (%) 60 40 20 -40 -25 -10 0 15 30 40 50 60 60 50 40 (HORIZONTAL) 90 AMBIENT TEMPERATURE (℃) 100 125 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz PF Power Factor Characteristic Constant Current Mode 1.00 0.98 0.96 0.94 0.92 0.90 0.88 0.86 0.84 0.82 0.80 0.
PAGE 4
HLN-80H 80W Single Output Switching Power Supply series DRIVING METHODS OF LED MODULE There are two major kinds of LED drive method "direct drive" and "with LED driver". A typical LED power supply may either work in "constant voltage mode (CV) or constant current mode (CC)" to drive the LEDs. Mean Well's LED power supply with CV+ CC characteristic can be operated at both CV mode (with LED driver, at area (A) and CC mode (direct drive, at area (B).
PAGE 5
HLN-80H 80W Single Output Switching Power Supply series ※Using the built-in dimming function on B-type model can't turn the lighting fixture totally dark. Please refer to the connection method below to achieve 0% brightness of the lighting fixture connecting to the LED power supply unit. ※Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.